Installation Manual

ManualsBrandsFront Runner ManualsPortable Fridge AccessoriesLoad Bed Cargo Slide / Medium

SSBS008_REV_A01

Load Bed Cargo Slide

MKIII - Medium

SSBS008

ENG

IMPORTANT WARNING!

IT IS CRITICAL THAT ALL FRONT RUNNER PRODUCTS BE PROPERLY AND SECURELY ASSEMBLED AND ATTACHED TO YOUR VEHICLE.

IMPROPER ATTACHMENT COULD RESULT IN AN AUTOMOBILE ACCIDENT, AND COULD CAUSE SERIOUS BODILY INJURY OR DEATH.

YOU ARE RESPONSIBLE FOR ASSEMBLING AND SECURING ALL FRONT RUNNER PRODUCTS TO YOUR VEHICLE. CHECKING THE ATTACHMENTS PRIOR TO USE, AND PERIODICALLY INSPECTING THE PRODUCTS FOR ADJUSTMENT, WEAR AND DAMAGE.

THEREFORE YOU MUST READ AND UNDERSTAND ALL OF THE INSTRUCTIONS AND PRECAUTIONS SUPPLIED WITH YOUR FRONT RUNNER PRODUCT PRIOR TO INSTALLATION OR USE.

IF YOU DO NOT UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS, OR IF YOU HAVE NO MECHANICAL EXPERIENCE AND ARE NOT THOROUGHLY FAMILIAR WITH THE INSTALLATION PROCEDURES,

YOU SHOULD HAVE THE PRODUCT INSTALLED BY A PROFESSIONAL INSTALLER OR OTHER QUALIFIED PERSONNEL.

READ ME !

Thank you for purchasing a Front Runner Load Bed Cargo Slide.

Before you start, take a moment to familiarize yourself with the Fitting Instructions and the components received.

Refer to Page 2 for a list of all the components, quantities and tools required.

READ ME !

NOTE: Front Runner will not be responsible for any damage caused by the failure to install the product according to these instructions.

Please call us if you have any questions about the installation of this product.

Summary of content (5 pages)

PAGE 1
Load Bed Cargo Slide MKIII - Medium ENG SSBS008 READ ME ! Thank you for purchasing a Front Runner Load Bed Cargo Slide. READ ME ! Before you start, take a moment to familiarize yourself with the Fitting Instructions and the components received. Refer to Page 2 for a list of all the components, quantities and tools required. NOTE: Front Runner will not be responsible for any damage caused by the failure to install the product according to these instructions.
PAGE 2
1 GET ORGANIZED Here is what you are looking at for SSBS008 IN THE BOX 1 2 3 4 5 6 7 8 9 10 1X 1X 1X 9X 2X 5X 10 X 9X 6X 9X TOOLS NEEDED Load Bed Cargo Slide MKIII - Medium M6x25 Countersink Bolt M10 Flat Washer M6x40 Hex Bolt M8 Nyloc Nut M6x25 Hex Bolt M6 Rivnut M6 Spring Washer 19x12.58x12 Aluminium Spacer M6x30x1 Flat Washer 10MM 17MM 10MM 17MM 4mm 4mm 9.5mm FIGURE 1.
PAGE 3
FIT AND SECURE 2 2.1 Before ﬁtting the Cargo Slide in the vehicle, remove the wood base by loosening the four M6 Button Head Bolts. 10MM 2.2 4MM To loosen the two rear bolts, open the Cargo Slide. Looking at both the left and right rear corners of the Cargo Slide (Item 1), loosen and remove the rubber stopper. This is done by gripping the stopper to prevent it from t urning and removing the M6 button head bolt as shown.
PAGE 4
FIT AND SECURE 2 Make sure you have closed the load bed tail gate to ensure that it does not make contact with the frame. Once you are satisﬁed with the positioning of the frame, mark the position of all the mounting points as indicated by the arrows onto the load body. 2.4 4MM 9MM Remove the frame and drill a 4mm pilot hole on each of your markings. Check the underside of the load bed before drilling to make sure that there is no piping or wiring in the way. Re-drill all of the pilot holes to 9mm.
PAGE 5
COMPLETION 3 3.1 Congratulations! You did it. Take a step back and admire your work! 4 INSTALL OTHER VEHICLE AND RACK ACCESSORIES Now's the time to visit your favorite Front Runner Dealer in person or online.