Installation Manual

ManualsBrandsFront Runner Manuals4WD & CampingUte Slimline II Load Bed Rack Kit / 1255(W) x 1560(L)

Universal LOAD BED

TRAY & Load BArs

READ ME FIRST:

Thank you for purchasing a Front Runner Slimline II Load Bed Rack or Load Bar Kit.

Your Kit will contain the following items:

1.) A Slimline II Tray or Load Bar Set

2.) Universal Load Bed Tracks

3.) Universal Load Bed Legs

The different sections in this document will help you fit the various items received in your kit.

Section 1: Fitment of Load Bed Tracks to your vehicle.

Section 2: Fitment of Universal Load Bay Legs & Slimline II Tray.

Section 3: Fitment of Universal Load Bay Legs & Load Bars.

INSTALL LOAD BED TRACKS

()

Here is what you are looking at for TBRU002. Please note that only one side's components are shown

below. Familiarize yourself with the parts and then step away from the work area and read through these

instructions from beginning to end. Take a moment as a little prep now may save you a lot of time later.

You will need:

 4 mm Hex key

 10 mm Wrench

 4 & 7 mm Drill bit

 Drill machine

INSTALL TIME: 2.5 Hours

 Marking pen

 Measuring tape

 Small Phillips Screwdriver

 Friend

Item # Quantity Description

1 4 M3 x 6 SELF TAPPING SCREW

2 12 M6 x 25 COUNTERSUNK BOLT

3 4 END CAP

4 2 LOAD BED TRACK

5 2 RUBBER TRACK LINER

6 6 CLAMP PLATE

7 12 M6 FLAT WASHER

8 12 M6 NYLOC NUT

TRBU002 / KRLBUNI2_REV

A00

TRBU002 / KRLBUNI2

Summary of content (6 pages)

PAGE 1
Universal LOAD BED TRAY & Load BArs TRBU002 / KRLBUNI2 INSTALL TIME: 2.5 Hours READ ME FIRST: Thank you for purchasing a Front Runner Slimline II Load Bed Rack or Load Bar Kit. Your Kit will contain the following items: 1.) A Slimline II Tray or Load Bar Set 2.) Universal Load Bed Tracks 3.) Universal Load Bed Legs The different sections in this document will help you fit the various items received in your kit. Section 1: Fitment of Load Bed Tracks to your vehicle.
PAGE 2
INSTALL LOAD BED TRACKS (b) (c) Looking inside the load bin of the vehicle, measure the length of the load bin from the back of the cabin below the rear window to the start of the tail gate. Using a marking pen, mark the midpoint. Mark Midpoint of Load Bed Make another two markings, 20 mm either side of your center marking from Step 2B.
PAGE 3
installation of slimline ii tray Note: If you have not fitted the Universal Load Bed Legs, fit them according to the Universal Load Bed Leg Fitting Instruction - Document LASS026. If your Slimline II Tray is not already assembled, assemble it as per the Slimline II Tray Universal Assembly Instruction - Document RRSTUNI.
PAGE 4
installation of slimline ii tray cont... (C) Slide an End Cap (Item 3) into the ends of Track and secure in position using the M3 x 6 Self Tapping Screw (Item 1). (D) Grab your friend and with one of you on each side of the Rack, flip it end over end so that the bolts are facing down. Approach the vehicle from the rear lifting the Rack above the Legs. Slowly lower the Rack lining up the bolts in the Rack with the holes in the Legs. You may need to adjust the position of the Legs.
PAGE 5
installation OF LOAD BARS Note: If you have not fitted the Universal Load Bed Tracks or Legs, please fit them as per the Universal Load Bed Track and Universal Load Bed Led Fitting Instructions (Documents TRBU001 & LASS026). (A) Slide an End Cap (Item 3) into the ends of Track and secure in position using the M3 x 6 Self Tapping Screw (Item 1). (B) Fit a Plastic End Caps received with your Load Bars into each end of the Load Bars as shown.
PAGE 6
installation OF LOAD BARS cont... (D) Position the Load Bay Legs as required and secure in position. Turn the Load Bars over so that the Bolts inserted in Step 2B are facing down. Lower the Load Bars onto the Legs, lining up the bolts in the Load Bars with the holes in the Legs. You may need to adjust the position of the Bolts. Place the M8 Flat Washers and M8 Nyloc Nuts supplied with the Universal Load Bed Legs onto the Bolts securing the Load Bars to the Legs and hand tighten.