Installation Guide
6
and fix the top hinge on the door,to make the door level,see chart 8.
Step 14:Check the sealing of the door,then refit the parts �ǃ�.
Chart 8
Placement of Wine Cooler
The wine cooler should be placed in dry and ventilated room. The location of
the wine cooler should not be irradiated by direct sunshine. The wine cooler
should be far away from heating sources, such as: cooking stove or heating
radiator. If the wine cooler has to be placed near heating source, please adopt
proper heating insulation board for insulation or keep the wine cooler at least
the following minimum distances away from the heating sources:
For electric stove: 3 .
For oil or coal stove: 30 .
Replacement of Door Hinge
The door hinges of this wine cooler can be interchanged between the left and
right sides.
Installation of Handle
1. Set the handle on the fixation shaft.
- 10 -
Fig. 7
Chart 2
Step 7:Remove the bolt on the bottom of the door by screwdriver�(see chart
3)
Step 8:Remove the screw� and the block �,then set them on the left side.(see
chart 3)
ľ
ļ
Ľ
Chart 3
Step 9:Change the hinge axis� from the right hole to left hole(see chart 4)
Ŀ
Chart 4
Step 10:Use knife to remove the parts�,see chart 5.
- 8 -
Fig. 6
Bushing
Stop
bracket
Install the wine cooler in the •
coolest part of a dry and ventilated
room, out of direct sunlight and
away from heating ducts or
registers. Do not place the wine
cooler next to heat-producing
appliances such as a range, oven
or dishwasher.
Level the wine cooler so the door close tightly.•
Do not over crowd the wine cooler or block cold air •
vents. Doing so causes the wine cooler to run longer
and use more energy. Shelves should not be lined
with aluminum foil, wax paper or paper toweling.
Liners interfere with cold air circulation, making the
wine cooler less efcient.
Wipe containers dry before placing them in the wine
•
cooler. This cuts down on moisture build-up inside
the unit.
Organize the wine cooler to reduce door openings.
•
Remove as many items as needed at one time and
close the door as soon as possible.
ENERGY SAVING TIPS
InStALLAtIOn
Cool Down Period
For best performance, allow 4 hours for the wine cooler to cool down completely. The wine cooler will run continuously
for the rst several hours.
Temperature Control for Single Zone Model
Indication of Temperature in Lower Chamber
: Press this button once and the temperature increase 1°C.
: Press this button once and the temperature decrease 1°C.
Indication of Temperature in Upper Chamber
: Press this button once and the temperature increase 1°C.
: Press this button once and the temperature decrease 1°C.
: Temperature display.
Light: Lighting button for LED lamp; it controls the on/off of lamp.
Power: On/off button used to turn on/off all load.
Press Light and Power together for 2 seconds and you can convert between
fahrenheit temperature and Celsius temperature.
Notice!
z The default temperature is 10/10°C, and the temperature after power
failure will be the temperature set before the power failure.
z To elongate the service life of compressor, please wait for at least 5
minutes before the wine cooler is restarted after power failure.
z Failure display
z If there is failure on the sensor, the screen may display failure code, such
as: E and F. When the screen displays the above-mentioned errors, please
do not disassemble it for check by yourself. You should contact local
after-sales service personnel for repair.
z If the temperature in the cooler is too low, it will display “L”.
When the temperature in the cooler is too high, the screen will display “H”
and will flash; under this state, the buzzer will buzz until 30 seconds; one
minute later, the buzzer will continue to give alarm in the next 30 seconds; after
the alarm is given for three times, it will not give alarm any more. You can
press any key to cancel sound alarm.
z When you put a lot of wines together in the cooler, the temperature in the
cooler may rise temporarily.
- 10 -
Temperature display
Light: This button turns the light ON and OFF.
Power: This buttons turns the power ON and OFF.
Press both Light and Power button’s at the same time
to change between Fahrenheit and Celsius temperatures.
Indication of Temperature in Lower Chamber
: Press this button once and the temperature increase 1°C.
: Press this button once and the temperature decrease 1°C.
Indication of Temperature in Upper Chamber
: Press this button once and the temperature increase 1°C.
: Press this button once and the temperature decrease 1°C.
: Temperature display.
Light: Lighting button for LED lamp; it controls the on/off of lamp.
Power: On/off button used to turn on/off all load.
Press Light and Power together for 2 seconds and you can convert between
fahrenheit temperature and Celsius temperature.
Notice!
z The default temperature is 10/10°C, and the temperature after power
failure will be the temperature set before the power failure.
z To elongate the service life of compressor, please wait for at least 5
minutes before the wine cooler is restarted after power failure.
z Failure display
z If there is failure on the sensor, the screen may display failure code, such
as: E and F. When the screen displays the above-mentioned errors, please
do not disassemble it for check by yourself. You should contact local
after-sales service personnel for repair.
z If the temperature in the cooler is too low, it will display “L”.
When the temperature in the cooler is too high, the screen will display “H”
and will flash; under this state, the buzzer will buzz until 30 seconds; one
minute later, the buzzer will continue to give alarm in the next 30 seconds; after
the alarm is given for three times, it will not give alarm any more. You can
press any key to cancel sound alarm.
z When you put a lot of wines together in the cooler, the temperature in the
cooler may rise temporarily.
- 10 -
Press this button once to increase temperature 1° F/C.
Press this button once to decrease temperature 1° F/C.
The wine cooler can be operated by adjusting the temperature control buttons (up arrow and down arrow) until
the desired temperature is reached.
The display will ash for a few seconds before set point is locked in.
The temperature range MIN and MAX is 41° - 64°F (5° - 18° C).
tEMpERAtuRE cOntROLS