Use and Care Manual

9
OVEN CONTROLS
Setting The Clock
The set clock key is used to set the clock. The clock may
be set for 12 or 24 hour time of day operation. The clock
was preset at the factory for 12 hour operation. When the
range is first plugged in, or when the power supply to the
range has been interrupted, the timer in the display will
flash. To set the clock (example below for 1:30)
1. Press set clock. CLO will appear in the display.
2. Press 1 3 0 to set the time of day to 1:30. CLO will stay
in the display.
3. Press start. CLO will disappear and the clock will start.
The clock must be set for the oven to operate. If you have a
power interruption of any kind remember to set the clock
when power is restored. When programming a delay start
make sure the clock is set to the correct time of day.
Changing Between 12 or 24 Hour Time of Day
Operation
1. Press and hold set clock for 6 seconds. CLO will
appear in the display.
2. Continue holding the key until 12Hr dAY or 24Hr dAY
appears in the display and the control beeps once.
3. Press self clean to switch between the 12 and 24 hour
time of day display. The display will show either 12Hr
dAY or 24Hr dAY.
4. Press start to accept the change or press off to reject
the change.
5. Reset the correct time as described above in Setting
the Clock instructions. If the 24 hour time of day mode
was chosen, the clock will display time from 0:00
through 23:59 hours.
Setting Continuous Bake or 6 Hour Energy Saving
The timer and self clean keys control the Continuos Bake
or 6 Hour Energy Saving features. The oven control has a
factory preset 6 Hour Energy Saving feature that will shut
off the oven if the oven control is left on for more than 6
hours. The oven can be programmed to override this
feature for Continuous Baking.
Setting the control for Continuous Bake or 6 Hour
Energy Saving:
1. Press and hold timer for 6 seconds. After 6 seconds
6Hr OFF or StAY On will appear in the display and the
control will beep once.
2. Press self clean to switch between the 6 Hour Energy
Saving and Continuous Bake features.
3. Press start to accept the change (display will return to
time of day) or press off to reject the change.
6Hr OFF indicates the control is set for the 6 Hour Energy
Saving mode. StAY On indicates the control is set for the
Continuous Bake feature.
Setting Temperature Display in Fahrenheit or
Celsius
The broil and self clean keys control the Fahrenheit or
Celsius temperature display modes. The oven has been
preset at the factory to display in Fahrenheit.
To change display from Fahrenheit to Celsius or
Celsius to Fahrenheit:
1. To tell if the display is set for Fahrenheit or Celsius
press broil and hold it for 6 seconds; 550° will appear
and broil will flash in the display and a beep will sound.
If FAhrnht appears, the display is set to show tempera-
tures in Fahrenheit. If CELSIUS appears, the display is
set to show temperatures in Celsius.
2. Press self clean to switch between Fahrenheit or
Celsius display modes. The display will show either
FAhrnht or CELSIUS.
3. Press start to accept the change or press off to reject
the change.
Setting Silent Control Operation
The delay start and self clean keys control the Silent
Control operation feature. This feature allows the oven
control to be operated with or without out sounds or beeps.
To change control from normal sound operation to
silent control operation
1. To set range for normal or silent operation press and
hold delay start. -- -- will appear and DELAY will flash
in the display. After 6 seconds bEEP On or bEEP OFF
will appear in the display.
2. Press self clean to switch between normal sound
operation and silent operation mode. The display will
show either bEEP On or bEEP OFF. If bEEP On
appears, the control will operate with normal sounds
and beeps. If bEEP OFF appears, the control is in the
silent operation mode.
3. Press start to accept the change or press off to reject
the change. Note: The control will always beep at the
end of a minute timer and will beep when a set temper-
ature has been reached, even if the control is set to
silent operation.