Service Manual

the button is pressed and held in for
longer than two seconds, the numbers will
continue to advance until the button is re-
leased.
1.3
Advance the minute setting by repeatedly
pushing, or pushing and holding the
minute button, as needed.
1.4
Push the Run/Set switch to the middle
(RUN) position.
2.
To set the alarm time:
2.1
Push the Run/Set switch to the left
(ALARM-SET position).
2.2
Set the alarm time by using the same pro-
cedure that you used to set the time of
day. Remember to set the hour for A.M.
(no letters in the corner of the display), or
P.M., as desired.
2.3
Return the Run/Set switch to the middle
(RUN) position. The readout will return to
the time-of-day setting.
3.
To operate the alarm:
3.1
With the alarm time set, push the alarm
(upper) switch to the left. An alarm "wave"
symbol and the letters "AL" will appear in
the upper left corner of the display when
the alarm is on.
3.2
When the displayed time of day coincides
with the alarm time, the alarm will sound.
If the "snooz" button is not pushed or the
alarm switch is not moved, the alarm will
automatically stop sounding after 1
minute, and will not sound again for 24
hours.
3.3
If desired, press the "snooz" button while
the alarm is sounding, to shut the alarm
off for 3 minutes. The alarm symbol will
flash in the display when the button is
pushed, and will continue to flash until the
alarm switch is moved or the alarm has
sounded for 1 minute. The snooze proce-
dure can be done as many times as de-
sired.
3.4
Move the alarm switch to the right when
you wish to shut off or cancel the alarm;
the alarm symbol will disappear.
Kysor Digital Clock, Optional
A Kysor digital clock (Fig. 2.14) has a constant red
display, which automatically adjusts the brightness
for day or night. The clock features a 24-hour alarm.
1.
To set the time of day:
1.1
Depress both of the time "Set" push but-
tons, labelled "Fast" and "Slow"; 12:00
A.M. will appear as the readout.
NOTE: A small illuminated red dot in the
upper left side of the clock (above "PM") in-
dicates P.M. No dot indicates A.M.
1.2
Advance to the correct time by pushing
either the "Fast" or "Slow" push button.
2.
To set the alarm:
2.1
Depress the alarm "Set" push button. Ob-
serve that a red lamp above the word
"Alarm" illuminates.
2.2
Set the alarm time by using the same pro-
cedure that you used to set the time of
day. Remember to select either A.M. (no
red dot) or P.M. (red dot illuminates) when
setting the alarm time.
2.3
After the desired alarm time appears, de-
press the alarm "Set" push button again.
The readout will return to the time of day,
and the red lamp will go out.
2.4
To set the alarm, depress the alarm "On"
push button. Observe that a red dot on
the right side of the time-of-day readout is
illuminated. The alarm is now set, and
when the displayed time of day coincides
with the alarm time, the alarm will sound.
2.5
To cancel or shut off the alarm, depress
the alarm "On" push button again. The red
dot on the face of the clock will go out.
Tachograph, Optional
A Sangamo tachograph (Fig. 2.30) indicates and
records vehicle speed, time, and distance traveled. It
also records the length of time the engine is oper-
ated when the vehicle is stationary. A warning light
comes on whenever a preestablished speed limit is
exceeded.
Instruments and Controls Identification
2.30