introduction Thank you for purchasing F-18 "Fighting Falcon” scale EDF jel. F-18 "Fighting Falcon® is a lightweight multi-role fighter manufactured in the United States, this excellent fighter, it received weeds attention from is first launch. Se far, total have 24 countries use this fighter to pro fact their country. No doubt, F-16 “Fighting Falcon” is the main fighter in Western countries. This is a new F-16 "Fighting Falcon” scale EDF jet brings us excellent scale details.
Installing Fuselage As the right photo shown, use glue to attach the front/rear fuselage and left f right foam parts. Connection tail flame light cable and extension cable in fuselage. Installing the elevator A-Gore FH B-starve Past Fe Straw pharisaic © -Malta fixed ring 1.Use servo tester or radio to center the servo am. 2. Connact the servo cable and extension] cable, then use "screw (A) fo fix the “serve (BY.
Installing rudder 1. Connact the rudder serve cabs, rudder LED light cable and extension cable in fuselage. 2.Insert the rudder on the tall of fuselage and use poss screws to fix. PAS*EMM {apes) installing Main wing A-Sower wri #17g larva cov C-17gssrvo box D-Allison horn £ Alfalfa push rod F Serra rough 1.Use savor tester or radio to center the servo arm. 2. Uss glue to attach the "17g serve box {C)" and “aileron hom (D)° on the aileron. 3.
installing missiles and pylons 1. As the right photo shown, Installed the missiles and pylons. When installing, pleads refer to the right ll photo, and check the direction of missile: TREE Milestone Te deo) & pylons Xenon directions (All direction) NON Ss installing Nose Cons . incense installed magnet, we only need to put the nose cone an the front of | fuselage. : Installing tall flame LED light module Replace the tail flame LED light, please refer to the right photo, install step by tap.
installing nose cabin door Please refer to the following drawing, assemblaldisassemble and replaces the sens cabin door.
Introduction of integrated circulate module of servo cables and LED light Integrated circuit module of servo cables and LED light have two function: 1.Switch off control of LED taxi light & cabin door. 2. All servo cables integrated adaption. This part can affectingly reduce the number of cables in battery compartment, Jet it become mars concise. We will bs mire clear when connect io receiver.
Install on battery integrated circuit mods of eva enables and LED it Receiver Our standard battery is: 68 22.2V S000mAh 25C You can choose the battery refer to the battery cabin size: L=254mm; W=84mm; H-5Smm the low position. w §522.2Y 5000mARh 6000mAh Discharge rate of C » 35C Different weight battery may affect its CG, please pay attention of the correct tangs of CG indication. Lift up tape.it removable canopy, then bundled battery with Velcro.
install powerless reinstalled the motor (I) in the dusted fan cover {C). 2.Fixed i with poss cup head screws (B). 3.Put the fan (E} into motor shaft. { please note the plat position of hardware which installed in the fan, and the plat position of miter shaft, please check the alignment io install together. TM Hi £0 4.Use the spinner (F) cover the fan, and use the cup head screw {G) io fix the spinner (F). 8.
Control direction lest After installed the plane, before flying, we need a fully charged battery and connect to the ESC, then use radio to test and check that every control surfaces work properly.
Troubleshooting Guide Marat doss not turn on A} Li-Po battery depleted B} Transmitter battles depleted ©) Transmitter not turreted on A) Recharge Li-Po battery 8) Rapists or recharge batteries ©) Tum on transmitter Dj Li-PS be fiery nol plugged in 3) Plugin Li-Po bestiary E} Motor not armed E} Arm motor F} Crash has damaged an maintain component 8} £8C or other damaged £) Replace 5) Chick ESC or contact local distributor Cub is difficult be control A} You ars flying in tao mush wind 8} Li-Po battery deplete
