Reference Manual
Table Of Contents
- Preface
- 1. Overview
- Untitled
- 2. Equipment
- 3. Installation
- 4. Basic Radio Programming and Setup
- 4.1. Define the Network Type and the Radio's Role in that Network
- 4.2. Establish Communication with Instrumentation and Computers
- 4.3. Establishing Communication with Other Radios in the Network
- 4.4. Set the Data Transmission Characteristics
- 4.5. Set Radio Passwords
- 4.6. Set the Hop Table Size in the Terminal Interface
- 4.7. Set the Radio to a Single Channel in a Terminal Emulator
- 4.8. Set the Radio to Hop Channels
- 4.9. Edit Frequencies for Multiple Channels
- 5. Configure Point-to-MultiPoint Networks
- 5.1. Point to MultiPoint Network Characteristics
- 5.2. Point-to-MultiPoint Network Quick Start (Terminal Interface)
- 5.3. Overlapping MultiPoint Networks
- 5.4. Establishing Communication with Other Radios in a MultiPoint Network
- 5.5. Routing Communication Through the Network
- 5.6. Setting Other MultiPoint Parameters
- 5.7. Reading Diagnostics in Tool Suite
- 6. Configure Point-to-Point Networks
- 7. View Radio Statistics
- 8. Release Notes
- 9. Additional Radio Information
- Appendix A: Technical Specifications
- Appendix B: RF Board Pin-Out
- Appendix C: RS232 Pin Assignments - DB9
- Appendix D: LRS455 Frequency Table
- Appendix E: Factory Default Settings
- Appendix F: Point-to-MultiPoint Operation LEDs
- Appendix G: Point-to-Point Operation LEDs
- Appendix H: FreeWave Legal Information
- Blank Page
- Blank Page
LUM0020CD Rev June-2020 Page 5 of 112 Copyright © 2019FreeWave
This document is subject to change without notice. This document is the property of FreeWave Technologies, Inc.
and contains proprietary information owned by FreeWave. This document cannot be reproduced in whole or in
part by any means without written permission from FreeWave Technologies, Inc.
5.6.3. DTR Connect 65
5.6.4. Local Mode 65
5.6.5. Master Packet Repeat 66
5.6.6. Max Slave Retry 67
5.6.7. Multi-Master Sync 67
5.6.8. Radio ID 67
5.6.9. Repeaters 67
5.6.10. Repeater Frequency 68
5.6.11. Retry Odds 68
5.6.12. Slave / Repeater 69
5.6.13. Subnet ID 70
5.7. Reading Diagnostics in Tool Suite 72
6. Configure Point-to-Point Networks 74
6.1. Point-to-Point Network Quick Start (Tool Suite) 75
6.2. Point-to-Point Network Quick Start (Terminal Interface) 77
6.3. Using Call Book in Point-to-Point Networks 79
6.3.1. Set the Call Book in Tool Suite 80
6.3.2. Set the Call Book in the Terminal Interface 80
7. View Radio Statistics 82
7.1. View Statistics in Tool Suite 83
7.2. View the Radio Transmission Characteristics in the Terminal Interface 83
7.3. Antenna Fwd 83
7.4. Antenna Reflected Power 83
7.5. Antenna Rev 83
7.6. Master-Slave Distance 84
7.7. Noise Level 84
7.8. Number of Disconnects 84
7.9. Radio Temperature 85
7.10. Rate % 85
7.11. Signal Level 85
8. Release Notes 86
8.1. Version 1.79 86
8.2. Version 1.77 87
8.3. Version 1.74 87
8.4. Version 1.72 88
8.5. Version 1.71 88
8.6. Version 1.70 89
8.7. Version 1.69d9 89
8.8. Version 1.67o 89
LRS455A-C, LRS455A-CE, LRS455-T
User-Reference Manual