Reference Manual
Table Of Contents
- Preface
- 1. Overview
- Untitled
- 2. Equipment
- 3. Installation
- 4. Basic Radio Programming and Setup
- 4.1. Define the Network Type and the Radio's Role in that Network
- 4.2. Establish Communication with Instrumentation and Computers
- 4.3. Establishing Communication with Other Radios in the Network
- 4.4. Set the Data Transmission Characteristics
- 4.5. Set Radio Passwords
- 4.6. Set the Hop Table Size in the Terminal Interface
- 4.7. Set the Radio to a Single Channel in a Terminal Emulator
- 4.8. Set the Radio to Hop Channels
- 4.9. Edit Frequencies for Multiple Channels
- 5. Configure Point-to-MultiPoint Networks
- 5.1. Point to MultiPoint Network Characteristics
- 5.2. Point-to-MultiPoint Network Quick Start (Terminal Interface)
- 5.3. Overlapping MultiPoint Networks
- 5.4. Establishing Communication with Other Radios in a MultiPoint Network
- 5.5. Routing Communication Through the Network
- 5.6. Setting Other MultiPoint Parameters
- 5.7. Reading Diagnostics in Tool Suite
- 6. Configure Point-to-Point Networks
- 7. View Radio Statistics
- 8. Release Notes
- 9. Additional Radio Information
- Appendix A: Technical Specifications
- Appendix B: RF Board Pin-Out
- Appendix C: RS232 Pin Assignments - DB9
- Appendix D: LRS455 Frequency Table
- Appendix E: Factory Default Settings
- Appendix F: Point-to-MultiPoint Operation LEDs
- Appendix G: Point-to-Point Operation LEDs
- Appendix H: FreeWave Legal Information
- Blank Page
- Blank Page
LUM0020CD Rev June-2020 Page 4 of 112 Copyright © 2019FreeWave
This document is subject to change without notice. This document is the property of FreeWave Technologies, Inc.
and contains proprietary information owned by FreeWave. This document cannot be reproduced in whole or in
part by any means without written permission from FreeWave Technologies, Inc.
4.4.2. Hop Table Size 38
4.4.3. Low Power Mode 38
Conserve Power 40
4.4.4. Max Packet Size and Min Packet Size 40
4.4.5. Network ID 43
4.4.6. Remote LED 43
4.4.7. Retry Timeout 44
4.4.8. RF Data Rate 45
4.4.9. RTS to CTS 46
4.4.10. Rx Frequency 46
4.4.11. Slave Security 47
4.4.12. Transmit Power 48
4.4.13. Transmit Rate 49
4.4.14. Tx Frequency 50
4.5. Set Radio Passwords 51
4.5.1. Set a Password 51
4.5.2. Change the Password 52
4.5.3. Disable the Password 52
4.6. Set the Hop Table Size in the Terminal Interface 53
4.7. Set the Radio to a Single Channel in a Terminal Emulator 53
4.8. Set the Radio to Hop Channels 53
4.9. Edit Frequencies for Multiple Channels 54
5. Configure Point-to-MultiPoint Networks 55
5.1. Point to MultiPoint Network Characteristics 56
5.1.1. Golden Settings 56
5.1.2. Master to Slave Communications 56
5.1.3. Slave to Master Communications 56
5.2. Point-to-MultiPoint Network Quick Start (Terminal Interface) 57
5.3. Overlapping MultiPoint Networks 58
5.4. Establishing Communication with Other Radios in a MultiPoint Network 59
5.4.1. Using the Network ID in MultiPoint Networks 59
5.4.2. Using the Call Book in MultiPoint Networks 59
5.5. Routing Communication Through the Network 61
5.5.1. Assigning Subnet ID Values 61
5.6. Setting Other MultiPoint Parameters 63
5.6.1. 1 PPS Enable Delay 63
Setup 1PPS Enable / Delay 64
Calibrate a Slave Radio in 1PPS Enable / Delay Mode 64
5.6.2. Diagnostics 64
LRS455A-C, LRS455A-CE, LRS455-T
User-Reference Manual