Reference Manual
Table Of Contents
- Preface
- 1. Overview
- Untitled
- 2. Equipment
- 3. Installation
- 4. Basic Radio Programming and Setup
- 4.1. Define the Network Type and the Radio's Role in that Network
- 4.2. Establish Communication with Instrumentation and Computers
- 4.3. Establishing Communication with Other Radios in the Network
- 4.4. Set the Data Transmission Characteristics
- 4.5. Set Radio Passwords
- 4.6. Set the Hop Table Size in the Terminal Interface
- 4.7. Set the Radio to a Single Channel in a Terminal Emulator
- 4.8. Set the Radio to Hop Channels
- 4.9. Edit Frequencies for Multiple Channels
- 5. Configure Point-to-MultiPoint Networks
- 5.1. Point to MultiPoint Network Characteristics
- 5.2. Point-to-MultiPoint Network Quick Start (Terminal Interface)
- 5.3. Overlapping MultiPoint Networks
- 5.4. Establishing Communication with Other Radios in a MultiPoint Network
- 5.5. Routing Communication Through the Network
- 5.6. Setting Other MultiPoint Parameters
- 5.7. Reading Diagnostics in Tool Suite
- 6. Configure Point-to-Point Networks
- 7. View Radio Statistics
- 8. Release Notes
- 9. Additional Radio Information
- Appendix A: Technical Specifications
- Appendix B: RF Board Pin-Out
- Appendix C: RS232 Pin Assignments - DB9
- Appendix D: LRS455 Frequency Table
- Appendix E: Factory Default Settings
- Appendix F: Point-to-MultiPoint Operation LEDs
- Appendix G: Point-to-Point Operation LEDs
- Appendix H: FreeWave Legal Information
- Blank Page
- Blank Page
3. Installation
LUM0020CD Rev June-2020 Page 24 of 112 Copyright © 2019FreeWave
This document is subject to change without notice. This document is the property of FreeWave Technologies, Inc.
and contains proprietary information owned by FreeWave. This document cannot be reproduced in whole or in
part by any means without written permission from FreeWave Technologies, Inc.
3.3. Configuration Tool Options
Note: The terms modem and radio are used interchangeably in this document and in the text within
the setup tools. While the words have different meanings, the two terms should be treated as one
and the same when referring to FreeWave products.
When the radio is in Setup mode, use either of these setup tools to configure the settings on the
radio:
l Tool Suite - provides a group of tools for configuring the devices in your network and for
monitoring the network's performance. Use the Configuration application in Tool Suite to
program changes to the radio's settings.
l Terminal Emulator - A terminal emulator program, e.g.,Tera Term, offers many of the
same configuration options that are available in the Configuration application in Tool
Suite.
3.3.1. Tool Suite and Terminal Emulators
If using a terminal emulator, the tabs for a device in Tool Suite mirror the Setup main menu
selections.
Example: Option 0 from the Setup main menu in the terminal menu setup is Set Operation Mode.
The corresponding configuration tab for the device in Tool Suite is (0) Operation Mode.
Figure 8: Tool Suite menu Matched to Terminal menu
Note: In this document, if the setup procedure in the terminal emulator is different than the procedure
in Tool Suite, the terminal instructions are also included.
LRS455A-C, LRS455A-CE, LRS455-T
User-Reference Manual
-
Device Informat ion (~ perat io n Mo~ t l ) Baud Rate
(2)Call Book (3) Transmission Characterist ics
(5) Mult iPoi1
◄
►
•
-
Modem Mode
I (0) Point to Point Maste r
[:JI
Setup Mode Timeout
I Disabled
G[
Ethernet Mode
I Disabled
G1
Slave IP Stack
I Disabled
Gl
Slave UDP Mode
jo
l•JI
Duplex
. l"UII
[•j ,
(0 )
Se l Oper a ti on Mode I
,,
J t::
~
~~~
n <Jl t::
2 Ed i I Ca l I Book
Local IP Address
I 255 '
255
, 255
. 255 I
3 Edi I Rad io Trans • iss i on Char ac ter-i s t ics
4 Show Rad io Sta ti s t ics
Local Port
J 65535
I
5 Edi t Mui t i Poi nt Par a1111e ter s
6
TOMA Menu
8
Chg Passw or d
Reply IP Address
1 255 . 255 , 255
. 255 1
Escl
Ei,ci t Set up
Reply Port
J 65535
I
Enter- Choi ce
-
-;;
< >
Ccrn9do!dl:ll2 :'50
--
192008-N-l N..N
'