Reference Manual
Table Of Contents
- Preface
- 1. Overview
- Untitled
- 2. Equipment
- 3. Installation
- 4. Basic Radio Programming and Setup
- 4.1. Define the Network Type and the Radio's Role in that Network
- 4.2. Establish Communication with Instrumentation and Computers
- 4.3. Establishing Communication with Other Radios in the Network
- 4.4. Set the Data Transmission Characteristics
- 4.5. Set Radio Passwords
- 4.6. Set the Hop Table Size in the Terminal Interface
- 4.7. Set the Radio to a Single Channel in a Terminal Emulator
- 4.8. Set the Radio to Hop Channels
- 4.9. Edit Frequencies for Multiple Channels
- 5. Configure Point-to-MultiPoint Networks
- 5.1. Point to MultiPoint Network Characteristics
- 5.2. Point-to-MultiPoint Network Quick Start (Terminal Interface)
- 5.3. Overlapping MultiPoint Networks
- 5.4. Establishing Communication with Other Radios in a MultiPoint Network
- 5.5. Routing Communication Through the Network
- 5.6. Setting Other MultiPoint Parameters
- 5.7. Reading Diagnostics in Tool Suite
- 6. Configure Point-to-Point Networks
- 7. View Radio Statistics
- 8. Release Notes
- 9. Additional Radio Information
- Appendix A: Technical Specifications
- Appendix B: RF Board Pin-Out
- Appendix C: RS232 Pin Assignments - DB9
- Appendix D: LRS455 Frequency Table
- Appendix E: Factory Default Settings
- Appendix F: Point-to-MultiPoint Operation LEDs
- Appendix G: Point-to-Point Operation LEDs
- Appendix H: FreeWave Legal Information
- Blank Page
- Blank Page
Appendix G: Point-to-Point Operation LEDs
Master Slave Repeater
Condition
Carrier
Detect
(CD)
Transmit
(Tx)
Clear to Send
(CTS)
Carrier
Detect
(CD)
Transmit
(Tx)
Clear to Send
(CTS)
Carrier
Detect
(CD)
Transmit
(Tx)
Clear to Send
(CTS)
Powered, no link
Solid Red
(Bright)
Solid Red
(Bright)
Solid Red
(Bright)
Solid Red
(Bright)
Off Solid Black
Blinking Red
Solid Red
(Bright)
Off Solid Black
Blinking Red
Linked.
No Repeater
Sending sparse data
Solid Green
Intermittent Red
Flash
Intermittent Red
Flash
Solid Green
Intermittent Red
Flash
Intermittent Red
Flash
N/A N/A N/A
Master calling
Slave through Repeater
Solid Red
(Bright)
Solid Red (Dim)
Solid Red
(Bright)
Solid Red
(Bright)
Off Solid Black
Blinking Red
Solid Red
(Bright)
Off Solid Black
Blinking Red
Master linked to
Repeater, not to Slave
Blinking
Orange
Solid Red (Dim)
Solid Red
(Bright)
Solid Red
(Bright)
Off Solid Black
Blinking Red
Solid Red
(Bright)
Solid Red (Dim)
Solid Red
(Bright)
Repeater linked to Slave
Solid Green
Intermittent Red
Flash
Intermittent Red
Flash
Solid Green
Intermittent Red
Flash
Intermittent Red
Flash
Solid Green
Intermittent Red
Flash
Intermittent Red
Flash
Mode 6
Waiting for ATD
command
Solid Red
(Bright)
Off Solid Black
Blinking Red
Solid Red
(Bright)
Off Solid Black
Blinking Red
N/A N/A N/A
Setup Mode
Solid Green
Solid Green Solid Green
Solid Green
Solid Green Solid Green
Solid Green
Solid Green Solid Green
LUM0020CD Rev June-2020 Page 107 of 112 Copyright © 2019FreeWave
This document is subject to change without notice. This document is the property of FreeWave Technologies, Inc. and contains proprietary information owned
by FreeWave. This document cannot be reproduced in whole or in part by any means without written permission from FreeWave Technologies, Inc.
Appendix G: Point-to-Point Operation LEDs LRS455A-C, LRS455A-CE, LRS455-T User-Reference Manual
- - - -
•
e
-
•
e
lo: lo: :o: :o:
-
•
- -
•
e
-
•
e
B
•
- -
•
e
-
•
-
:O! lo! :O! lO! :O! lo!
-
•
e
-
•
e