User guide
7
adjustments
to
the armrest
angle
you will
need
two 13mm
spanners
(not
provided). Lift
the
arm upwar
ds,
you will note
the adjusting
bolt.
F
irst
loosen the locking
nut,
rotate
the
bolt
in
or
out
until
the
required
angle
is
found,
lower the
arm and
check
the
angle
for
comfort;
re-adjust
as
necessar
y
.
F
inally
tighten the locking
nut.
Warning:
When
lowering the
arm
mak
e
certain
clothing
or
fingers
are
not
positioned
under
it.
4.
Seat Slide
A
djustment:
(Fig
4).
Located
on
the
right
front
side
of
the
seat. This lever allows
you
to
adjust
your
seat
for
wards and backwards when
sitting
on
the
seat. Simply
pull
up
the
lever and move
in
the desired
position
backwards
by
pushing
or for
war
d
by
hitching. As soon
as
the
lever is
released,
the
seat
will lock
into
the
new
position.
Caution:
Test
that the
seat
has
fully lock
ed
by hitching
backwards and
for
war
ds.
Warning:
Do
not
car
r
y
out
this operation
when
your
Scooter
is
moving,
first
stop
apply the brak
es
and
then
car
r
y
out
the
seat
positioning.
SCOOTER
SEA
T
:
(Fig
5).
The
seat
as
fitted
to
your
Richmond Scooter
,
has
a
fold
down
backrest.
The
seat
has
two
height
positions.
Y
our
F
reerider
distributor
will
position
the
seat
to
allow
you
the most
comfortable
drivin g
position.
5.
Seat
Height
A
djustment:
Y
ou
may
need
to
alter the
seat
height setting
at
a
later date,
please
follow
these
instructions.
1.
R
emove
your
seat
from
the Scooter by
lifting
the
seat
locking
lever and
lifting
the
seat
clear
of
the
vehicle
(see
F
ig
1).
Note your
seat
for
safety reasons
can
only
be
removed
when
it
is
turned
90˚
to
the
right
or
left from
the straight
ahead
drivin g
position.
Please
tak
e
care
when
lifting
heavy
weights.
Place
your
seat
on
a
soft
clean
work
area.
2.
W
ith
the aid
of
a
17mm
spanner
(not
supplied)
loosen
the
10mm
seat
clamp
fixing
bolt
(see
F
ig
6).
3.
R
emove
the
10mm fixing
bolt
and
reposition
the
bolt into
one
of
the
two preferred location
holes
of
the
seat
mounting
tube
(see
F
ig
6).
4.
R
e
-tighten
the
10mm fixing
bolt.
R
efit
the
seat
onto
your
Scooter
.
Warning:
Do
not
have
the
seat
set
too
high,
you
must
be
abl e
to
place
both
feet
firmly on
the Scooter
’s
floor
area.
Stability
will
be
reduced
the
higher
your
seat
is
set
on
the
handlebar
from
a
lock
ed
position pull
the
black lever
FIG
3
FIG
4
FIG
5
FIG
6
the
mounting
tube.
Always
tak
e
great care when
cornering,
lean
into the corner
to
achieve
the
best
stability
fr
om your
Scooter
.
HANDLEBAR ADJUSTMENT
The handlebar
of
your
Scooter
is designed
to
allow
you
to
position
it
in
a
comfortable
drivin g
position.
It
can
be
lock
ed
into
numerous
positions
or
unlock
ed
to
move
freely
for
transportation.
The handlebar
lock
is
operated by
a
black lever
positioned
on
the
right
hand side
of
the
handlebar
(see
F
ig
7,
page
8).
T
o
release
upwar
ds, the
handlebar
will
now
move
freely
,
but
under
mild
tension.
T
o
lock
the
handlebar
into
a
comfortable
drivin g
position,
simply
push
the
black lever
downwar
ds
until
the
handlebar is
lock
ed
firmly
into
position.
W
i
th
the
combination
of
the
seat
slide
and
height adjustment
together
with
the
handlebar
movement,
you
should
find
a
suitably
comfortable
drivin g
position.
Warning:
Always
mak
e
certain the
handlebar
locking
lever is
fully
down
and
the
handlebar is securely clamped
onto
the chrome