Assembly Instructions

ManualsBrandsFreeport Park ManualsOutdoor SaleRobert 10 Ft. W x 10 Ft. D Metal Patio Gazebo

Page 1 OF 12

Caution : You must read this before you proceed.

Read all instructions before assembling and using this product

1. Select ideal location. Set out all parts on a clear and level surface prior to assembly. Ideally, the Gazebo should be set up in

the desired location to avoid moving it after assembly.

2. Team Work. We recommend 4-5 adults and it may require 3 to 4 hours to fully ass

emble the Gazebo. If possible, please use

safety ladders.

3. Use caution. During the entire assembly process, especially when lifting heavy or large parts or using ladders, pay attention

to safety. No one other than those assistants should be allowed in the work area.

4. Check all available parts. Before assembling your Gazebo Frame, make sure that you have all the parts described in the Parts

List.

5. Ensure that ALL BOLTS are fully and securely bolted in before you proceed to attach the Canopies.

6. Keep children away. Children shouldn’t be allowed in the work area. Do not let them handle parts and tools. Do not allow

children to climb the Gazebo.

7. It is recommended that the canopy be removed during strong windy conditions.

Gazebo

Summary of content (12 pages)

PAGE 1
Assembly Instructions Caution : You must read this before you proceed. Read all instructions before assembling and using this product 1. Select ideal location. Set out all parts on a clear and level surface prior to assembly. Ideally, the Gazebo should be set up in the desired location to avoid moving it after assembly. 2. Team Work. We recommend 4-5 adults and it may require 3 to 4 hours to fully assemble the Gazebo. If possible, please use safety ladders. 3. Use caution.
PAGE 2
Parts List Label Picture Description QTY A Crossbar 2 B Crossbar 2 C Crossbar 2 D Crossbar 2 E Main Pillar 4 F Supporting Fabric Tube 2 G Supporting Fabric Tube 2 H Supporting Fabric Tube 2 I Supporting Fabric Tube 2 Page 2 OF 12
PAGE 3
J Pull Tube 2 K Pull Tube 2 L Brace 8 M Canopy 2 Description QTY Hardware Label ① Picture Bolt/Washer/Spacer (M6*45) 7 ② Bolt/Washer (M6*15) 66 ③ Wrench 1 ④ Stake 8 Page 3 OF 12
PAGE 4
Assembly Preparation Before Beginning Assembly: ×66 ×7 ×1 ×8 Page 4 OF 12
PAGE 5
Assembly Steps Crossbar (B) Crossbar (C) Crossbar (A) Crossbar (D) Crossbar (D) Crossbar (A) Crossbar (B) Main Pillar (E) Canopy (M) Crossbar (C) Main Pillar (E) Main Pillar (E) Main Pillar (E) This Gazebo has multiple parts and may require up to 3-4 hours to assemble. To give you an overview of the Gazebo parts, the above picture is to help you put the various parts into perspective. Please read through the instructions below to familiarise yourself with the parts and steps before assembly.
PAGE 6
Step 1 A B 2 A B 2 Fig.1 Attach Crossbars(A) to Crossbars(B) using Bolts(②) with Wrench(③). (See Fig. 1) Note: Make sure the direction of the Crossbars are the same as per the above drawing. Tighten all Bolts in a sequential manner.
PAGE 7
Step 2 D C 2 C D 2 F ig.2 C D I H I H C D D C H I 1 I H 1 1 F ig.3 Attach Crossbars(C) to Crossbars(D) using Bolts(②) with Wrench(③). (See Fig. 2) Note: Make sure the direction of the Crossbars are the same as per the above drawing. Attach Supporting Fabric Tubes(I) and Supporting Fabric Tubes(H) together to the Crossbar (D) using Bolts(①) with Wrench(③) Attach Supporting Fabric Tubes(I) to Crossbars(D) using Bolts(①) with Wrench(③).
PAGE 8
Step 3 E L E A 2 L 2 2 A 2 B Fig.4 E L Attach Crossbars(A) to Main Pillars(E) using Bolts(②) with Wrench(③). Attach Braces(L) to Main Pillars(E) and Crossbars(A) using Bolts(②) with Wrench(③). (See Fig. 4) Attach Crossbars(B) to Main Pillars(E) using Bolts(②) with Wrench(③). Attach Braces(L) to Main Pillars(E) and Crossbars(B) using Bolts(②) with Wrench(③). Do not fully tighten the Bolts.
PAGE 9
Step 4 A D 2 2 L 2 2 E Fig.5 B A C H D L I I D H A E B C L L E E E Attach Crossbars(C) to Main Pillars(E) using Bolts(②) with Wrench(③). Attach Braces(L) to Main Pillars(E) and Crossbars(C) using Bolts(②) with Wrench(③). Attach Crossbars(D) to Main Pillars(E) using Bolts(②) with Wrench(③). Attach Braces(L) to Main Pillars(E) and Crossbars(D) using Bolts(②) with Wrench(③). (See Fig. 5) Do not fully tighten the Bolts.
PAGE 10
Step 5 A/B 2 2 Fig.7 B A C G H D L F I Fig.6 F I D Fig.6 H A B E E G F L C L E G E Fig.6 Attach Supporting Fabric Tubes(F) to Supporting Fabric Tubes(G) using the preattached snap buttons. (See Fig.6) Attach Supporting Fabric Tubes(F/G) the Crossbars(A/B) using Bolts(②) with Wrench(③). (See Fig.7). Now, fully and securely, tighten all bolts, at all joints.
PAGE 11
Step 6 M M E E Fig.8 Fig.9 K J E E Fig.8 M M F/G Fig.10 F/G H/I F/G J/K Fig.9.1 M 4 E 4 E Fig.9.2 Fig.10 Attach the Pull Tube (J) to the Pull Tube (K) using the preattached snap buttons. (See Fig.8) Insert the Canopy(M) through Supporting Fabric Tubes(H/I), then onto Supporting Fabric Tubes(F/G). Insert the Pull Tubes(J/K) into the sleeves of the Canopy(M). Fastening all lashings to the Main Pillars. (See Fig.
PAGE 12
Page 12 OF 12