RBI-100 CALLER ID User’s Guide Mode d’emploi • Manual del usuario 40
Introduction Congratulations! You now own a Rolodex® Electronics Caller ID.
Introduction ® New Call Indicator Light New Message Indicator Light NEW MSG REVIEW SET DEL Down Delete Up Set Battery Compartment Door Wall Mount Wall Mount Phone Jack and Line Jack (Interchangeable) 2
Getting Started To Install the Battery (Not Included) Note: The Caller ID will not function without a battery. 1. Disconnect the telephone line. 2. Lift the battery compartment door on the back of the Caller ID. 3. Install a 9-volt battery. 4. Replace the battery compartment door. To Connect the Telephone Line 1. Connect one end of the telephone cord into one of the jacks on the back of the Caller ID (either jack can be used) and connect its other end into the wall jack. 2.
Changing the Settings Caution: When you press SET to change a setting, that setting will flash on the screen for about 5 seconds. If you do not adjust the setting and then press SET during this time, the settings will remain unchanged. To Set the Time and Date 1. Press SET until ENTER TIME appears and the hour is flashing. or to adjust the hour. 2. Use You can also adjust AM and PM on the 12-hour clock while adjusting the hour.
Changing the Settings To Set the Language and Area Code 1. To set the language of the screen prompts, press SET until IN ENGLISH? appears. 2. Use or to set a language. 3. To set your area code, press SET until ENTER AREA CODE appears and the first digit of the area code flashes. or to change the first digit. 4. Use 5. To change the other digits, press SET until the or . desired digit flashes and then use Note: If your area code has three digits, press SET again when the fourth digit flashes.
Receiving Calls When the telephone connected to the Caller ID rings, new call information appears between the first and second ring. If you answer before the second ring, the Caller ID will not display any information. When a call is received, the Caller ID displays a call record, which can include, if available, the name of the caller, the caller’s telephone number, and the time that the call was placed. The amount of information displayed depends on the signal sent by your phone company.
Reviewing Calls This Caller ID automatically stores the call information from the last 90 calls. If you have not received any new calls, the Caller ID will display the date, time, and number of total calls, if any. If you have received new calls, the screen will display the appropriate number (ex: 03 NEW CALLS). 4-11 PM 4:27 NEW ONE NEW CALL 1. To review your new calls, press repeatedly. 2. To review your old calls, press repeatedly.
Reviewing Calls ✓ About Message Waiting Your Caller ID can alert you to check your phones messages if you have a voice mail service from your phone company that offers Caller ID signalling. For more information about these services, contact your phone company. When you have a new message, the phone company will send a signal to your Caller ID that causes the MSG light to blink and a marker to appear on the display the next time you receive a call.
Deleting Calls To Delete Individual Calls When you are reviewing a call record, you can delete it from your Caller ID’s memory. 1. Use or to find the call record you want to delete. 2. Hold DEL for about 1 second. The call record will be deleted and the next call record will be displayed. To Delete All Your Calls 1. Use or until you see TOP OF LIST or END OF LIST. 2. Hold DEL until DELETE ALL? appears. Warning! If you continue with these steps all your call records will be deleted.
Troubleshooting ✓ When the Battery Is Low When the battery is low on power, the low battery marker ( ) appears on the display. You should change the battery as soon as possible to ensure normal operation. Warning! Your call records may be erased if the Caller ID is without a battery for more than 20 seconds, so be sure to have a fresh battery on hand before you remove the old battery. To learn how to install a battery, read “Getting Started.
Troubleshooting • To reduce the risk of electric shock, do not disassemble this product. Take it to a qualified serviceman when service or repair work is required. Opening or removing covers may expose you to dangerous voltages or other risks. Incorrect reassembly can cause electric shock when the appliance is subsequently used. • Unplug this product from the telephone lines and refer to qualified service personnel under the following conditions: A. If the product has been exposed to liquid. B.
Limited Warranty (U.S. only) Franklin Electronic Publishers, Inc. (“Franklin”) warrants to the end user that this product will be free from defects in material and workmanship for a period of ONE YEAR from the date of original retail purchase, as evidenced by sales receipt. On discovery of a defect, the end user must return this product (transportation charges prepaid) either to the dealer from whom it was purchased or directly to Franklin at the address given below.
Product Information Specifications Model: RBI-100 • Dimensions: 111 x 67 x 70 mm • Weight: 4.7 oz. • REN 0.0B Cleaning, Storage, Problems To clean this Caller ID, spray a mild glass cleaner onto a cloth and wipe its surface. Don’t spray liquids directly on the Caller ID. Don’t use or store this Caller ID in extreme or prolonged heat, cold, humidity, or other adverse conditions. If you have a problem with your Caller ID, refer to the limited warranty.
