Installation Owner manual

7 Page 7 - 10 TANK SENTINEL
®
INSTALLATION GUIDE
PROBE 1
-(BLK) +(RED)
PROBE 4 PROBE 3PROBE 2
SHLD -(BLK) SHLD +(RED) -(BLK) +(RED) SHLD -(BLK) SHLD +(RED)
BLACK WIRE ( - )
SHLD (SHIELD)
- BARE WIRE -
I.S. Liquid Level Probe
Interface Terminal Wiring
Enlarged View
F16
F14
SEE
WIRING
DETAIL
BASED ON
PROBE TYPE (MODEL)
bb
aa
cc
INTRINSIC
SAFETY (I.S.)
TERMINAL GUARD
COVER FOR PROBE & SENSOR
TERMINALS
J17
F17
F15
J15
J16
POW ER
ON
SW 1
OFF
+
+
B1
J14
J13
J19
SENSOR 9 SENSO R 10
bb
GND(BLK) IN ( W H T ) PWR(RED) PWR(RED) IN ( W H T )
SENSOR 5 SENSO R 6
IN (W H T ) GN D(BLK) PWR(RED) PWR(RED) IN (W H T )
SENSOR 2SENSOR 1
-(BLK) SHLD +(RED) +(RED) -(BLK)
PWR(RED) IN (W H T ) GN D(BLK) PWR(RED) IN (W H T )
J18
aa
PROBE 2 PROBE 1
TP4
RED, OR
YELLOW WIRE ( + )
LIQUID LEVEL PROBE INPUT CHANNEL
#4 WIRING
SHOWN TYPICAL
RED, YELLOW,
OR WHITE WIRE ( + )
SEE: FIGURES 7-4a & 7-4b
FOR PROBE WIRING
& TS-DB1 SPLICE KIT DETAIL
TSP-LL2 PROBE
TSP-LL2 PROBE
NEW STYLE
POW ER
TERMINAL
SAFETY SHIELD
(CLEAR COVER)
dd
SAFETY
GND
RELAY OU TPUTS
C 2
NO 2
NO 1
NC 2
C 1
NC 1
- I.S. WEATHERPROOF PULL BOX
FOR INTRINSICALLY SAFE PROBE
AND SENSOR CABLE/WIRES - ONLY !
- EYS SEAL FITTING
- UNISTRUT & NUT ASSEMBLY
WEATHERPROOF
JUNCTION BOX
TS- L LD
DSY
IN P U T S
POWER
GND
dd
L1
GND
NEUT
GND
IN 2
S.RTN
IN 1
485B
485A
SENSOR 11 SENSOR 12
IN ( W H T ) GND(BLK) PWR(RED) GND(BLK) IN ( W H T ) PWR(RED) GND(BLK)
EYS SEAL
RMC
(TYPICAL)
(SHLD) SHIELD,
- BARE WIRE -
BLACK WIRE ( - )
I.S .
PROBE
&
SENSOR
PC Bd
GN D(BLK) PWR(RED) IN (W H T ) GN D(BLK) PWR(RED) IN (W H T ) GN D(BLK)
SENSOR 7 SENSOR 8
SENSOR 3
IN (W H T ) GN D(BLK) PWR(RED) GN D(BLK) IN (W H T ) PWR(RED) GN D(BLK)
SENSOR 4
cc
PROBE 3 PROB E 4
-(BLK) SHLD +(RED) SHLD -(BLK) +(RED) SHLD
WARNING:
LETHAL VOLTAGES COULD EXIST !
LOCAT E AND DISCONNECT ALL EXTERNAL POWER SOURCES
BEFORE WORKING ON OR SERVICING THESE CIRCUITS —
REINSTALL THIS COVER BEFORE OPERATING EQUIPMENT.
PROBE & SENSOR type & location:
Tank - 1
Tank - 2
Tank - 3
Tank - 4
Sensor 1
Sensor 2
Sensor 3
Sensor 4
Sensor 5
Sensor 6
Sensor 7
Sensor 8
Sensor 9
Sensor 10
Sensor 11
Sensor 12
INPUT 1
INPUT 2
RELAY 1
RELAY 2
240-2032
-wired to-
WARNING
THIS COVER MUST BE INSTALLED TO MAINTAIN
INTRINSIC SAFETY ! OPERATING THE SYSTEM WITH
THIS COVER REMOVED COULD RESULT IN AN
EXPLOSION HAZARD. CONSULT THE INSTALLATION
MANUAL FOR MORE INFORMATION.
Also see Figure 7-2a for
the T4, T7 & T8 probe
Terminal Board
arrangement, and see
Figure 7-2b for the T2 TB
arrangement.
Figure 7-5. Console to Liquid Level Probe Wiring (General)