Installation Guide

ManualsBrandsFranklin Brass ManualsBathFutura 24 in. Towel Shelf with Towel Bar in Polished Chrome

4 53/64"

[122.6 mm]

23 3/4"

[603.0 mm]

23 3/4"

[603.0 mm]

1 9/64"

[29.0 mm]

9/16"

[14.5 mm]

TOP

These installation instructions are for typical 1/2" drywall.

• For wood stud installation, use #6 x 1-1/4" wood screws.

Locate mounting hardware before discarding any packaging. Mounting hardware packed in Red Bag.

5A) Using a drill and a 3/16-in. drill bit, drill pilot holes in the marked location.

5B) Gently tap in wall anchors (E) with a hammer.

Please note: These installation instructions are intended for typical 1/2-in.

drywall and do not include instructions for installing into wood, tile or stucco.

When installing directly into woods studs, use #6 1 1/4-in. woods screws.

With mounting brackets facing outward, attach provided screws (D) into

installed anchors (E) and tighten with a screw driver.

Inquiries: 140 Business Park Dr. • Winston-Salem, NC, USA 27107

1-800-542-3789

Installation Instructions - Futura Vave Shelf Assembly

Attach support brace (B) to the left post of the pre-assembled shelf with

machine screw (G).

Repeat the process from step 1 on the right post of the pre-assembled shelf

Place fully assembled shelf on the included template on a flat surface and

make sure the post locations of the shelf align with the post locations

of the template.

4A) Using a level to ensure that template is properly aligned vertically and

horizontally, secure the template to the wall with tape.

4B) Using a pencil, mark holes.

Using the allen wrench, loosen the set screws (F) from the bottom of the

both posts and attach both posts to mounting brackets. Tighten set screw

with allen wrench.

With the remaining provided screws (D), securely fasten support braces

to the wall using a screw driver.

Electric drill

une pereuse électrique

taladro eléctric

3/16 in. drill bit / 1/16 in. drill bit

foret de 3/16 po / foret de 1/16 po

broca de 3/16 in / broca de 1/16 in

Hammer

marteau

martillo

Phillips screw driver

tournevis Phillips

destornillador en cruz Phillips

Safety goggles

lunettes de sécurit

gafas de seguridad

Level

niveau

nivel

Pencil

crayon

lápiz

Allen wrench

clé Allen

llave Allen

masking / painters’ tape

ruban masque / ruban cache

Cinta adhesiva de papel / para pintor

Summary of content (2 pages)

PAGE 1
TOP 23 3/4" [603.0 mm] 1x 1 A 1x B 1x 7 4 G 2x F 1 9/64" [29.0 mm] 1x 2x A 4A B 4B Attach support brace (B) to the left post of the pre-assembled shelf with machine screw (G). 2x 4A) Using a level to ensure that template is properly aligned vertically and horizontally, secure the template to the wall with tape. 4B) Using a pencil, mark holes. Using the allen wrench, loosen the set screws (F) from the bottom of the both posts and attach both posts to mounting brackets.
PAGE 2
Care Instructions: Care should be given to the cleaning of this product. Although its finish is extremely durable, it can be damaged by harsh abrasives or polish. To clean, simply wipe gently with a damp cloth and blot dry with a soft towel. Warranty Information Instrucciones sobre el cuidado: Se debe tener cuidado con la limpieza de este producto. Consignes d'Entretien: Il faut faire attention à la façon dont ce produit est nettoyé.