INSTALLATION GUIDE Little Butler® Hot Water Dispensing Faucets and Drinking Water Dispensing Faucets Rev 1 - 8/4/2017 DW6100C & LB6100C Series LB6200C Series DW7000C & LB7100C Series LB7200C Series DW9000C & LB9100C Series LB9200C Series MAKE IT WONDERFUL
TECHNICAL DATA Pressure Range - MINIMUM 35 PSI - Recommended Maximum 75 PSI has certified that this faucet complies with ASME A112.18.1/CSA B125.1, NSF61 and NSF372 drinking water system component requirements. These requirements meet California Health and Safety Code requirements for low lead (AB1953) as well as the low lead requirements of the US Safe Drinking Water Act of 2014. INSTALLATION INSTRUCTIONS 1 Remove all contents from the package and check for completeness.
Installation Little Butler® Series Hot only Faucets (LB_100C) Package Contents: 1 1 - Faucet (item pictured may differ from faucet you have.
Installation 2 For best result, Franke recommends this faucet be installed by a licensed, professional plumber. The installer should familiarize themselves with how this dispensing faucet will be installed and function as part of a point-of-use hot water, a filtration only drinking water, or a combination hot and filtered point-of-use water dispensing arrangement BEFORE the products are installed. Make certain to observe all local plumbing and building codes during installation of this unit.
Installation 3 It is recommended to take the components and locate their optimum positions before starting the installation. Make sure there is adequate clearance for the dispenser handle(s) to open fully without interference. Make sure all plumbing and electrical connections will reach the intended mounting positions for all the components and there will be no obstructions or sharp bends in plumbing. Make sure the counter top is no thicker than 2-¼”.
Installation 4 Ensure proper hole is in place for the faucet. This faucet is designed for a 1-3/8” (35mm) mounting hole. Before inserting the faucet in the hole in the sink or counter top, make sure the O-ring is positioned in its seat. All supply hoses are factory installed for convenience and to ensure a proper connection. Place the faucet in the hole, orienting the spout towards the sink bowl. NOTE: There should be a service label attached to one of the supply hoses on the faucet.
Installation 6 7 Take the black 3/8” poly-tubing from the faucet and connect it to the outlet of the filtration system as outlined in the filtration system instructions. If you decide not to utilize a filtration system with your LB_100 Series faucet, you must provide a connection for the black 3/8” poly-tube to the home’s cold water supply. This will complete the installation for the Drinking Water only (DW_ _00C Series) dispensing faucets.
Usage 1 Push the handle(s) back to turn on the water supply and foreward to turn the water off the water supply. Note: The spout has a 360° swivel capability HOT COLD ON 2 3 OFF WARNING! Do not operate both handles at the same time, as this can build up pressure in the heating tank causing the bladder to expand and eventually burst. Such damage is not covered by the warranty.
MAINTENANCE 1 Trouble Shooting PROBLEM POSSIBLE CAUSE RECOMMENDED ACTION Water spews and steams forcefully from spout with the dispenser in the off position -The heating tank is boiling because temperature setting it too high Lower temperature adjustment on the heating tank. Turn on faucet lever and run water until stream is normal again.
2 Replacement Parts Replacement Part # for Identified Part Model # LB6100 Series LB6200 Series DW6100 Series LB7100 Series LB7200 Series DW7000 Series LB9100 Series LB9200 Series DW9000 Series #1 Cartridge #2 Cartridge Nut Assembly #3 Lever Assembly (see chart below for all series) Cold Hot 5-036 5-036 5-036 5-036 5-036 5-036 5-036 5-036 5-036 5-042* 5-042* 5-042* 5-042* 5-042* 5-042* 5-042* 5-042* 5-042* 5-039* 5-039* 5-040* 5-040* 5-041* 5-041* 5-039H* 5-039H* 5-040H* 5-040H* 5-041H* 5-041H* -
WARRANTY Congratulations on the purchase of this Franke product! Franke is one of the world’s largest manufacturers of kitchen systems. Our products are manufactured using the highest degree of technology quality and design. As a result we are proud to offer the following warranty. Franke Kitchen Systems, LLC , warrants the quality of its water dispensing systems to be free from manufacturing defects for a period of five years from the date of purchase.
Franke Kitchen Systems, LLC 800 Aviation Parkway Smyrna, TN 37167 Phone: 1-800-626-5771 Fax: 1-888-685-0007 www.franke.us/ks.
