Installation Sheet

TECHNICAL DATA
NOTE:
CONTENTS IN BOX
INSTALLATION INSTRUCTIONS
Contact us immediatly if you see inconsistencies.
Phone: [phone])
website: www.franke.us/ks
email: [e-mail]
Flow Rate
Recommended Water Pressure
Max. Water Pressure
Recommended Hot Water Temp.
Hole Size For Faucet
Certies this faucet complies with ASME A112.18.1 / CSA B125.1
& NSF 61, NSF 372 and AB1953
1.75 GPM at 60 PSI
30-75 PSI
145 PSI
120°-140° F
1 3/8”
1. Remove all contents from the package and check for completeness.
2. Turn o water supply.
3. Remove faucet and hardware from its protective packaging.
Faucet comes assembled.
4. Cut a mounting hole 1 3/8 diameter (35mm) in the desired position in
counter top or sink (if one isn’t available) and cut a mounting hole
1 1/8 diameter (30mm) for side spray spray mounting.
5. Slide the rubber washer (2) over the faucet shank and place in the
escutcheon groove.
2
5
1
7
4
3
6
8
10
20
21
17
15
18
14
11
9
13
19
ATTENTION: For steps 5 and 8
The washer should be sitting between the countertop and faucet base.
DO NOT use putty or other sealant at this location. For solid surface
installation the countertop mounting surface needs to be at and free of
debris, otherwise the faucet or side spray may not sit properly. For tile
installations, avoid installing faucet or side spray near or on top of grout
lines. This may cause a weak joint and could cause leaks.
6. Install the mounting hardware to the base of the faucet body in the
following order – rubber washer (3), plastic ange (4), xing plate (5), and
xing nut (6) as illustrated.
7. Tighten the xing nut (6) onto the body (1)
8. Slide the rubber washer (14) over the side spray mounting ange shank
and place in the groove.
9. Install the side spray mounting hardware to the base of the side spray
mounting ange (13), in the following order – rubber washer (15),
Plastic spacer (16), xing plate (17), and xing nut (18).
10. Connect side spray shower (11) to side spray supply hose (19) by
hand. Make sure sealing washer (12) is in place on the supply hose,
otherwise the side spray will leak.
11. Insert the side spray supply hose (19) into the side spray mounting
ange (13) from the top
12. Connect the side spray supply hose (8) coming from the faucet
body to the top of the side spray diverter (10).
13. Connect the side spray return hose (9) to the left side (largest
tting) of the side spray diverter (10).
15. Secure the weight (20) to the side spray supply hose (19) with the
screws (21) approximately 2” (50mm) above the bend in the bottom of
the side spray supply hose (19).
16. Connect the supply hoses (7) to the water supply in the home and
turn on the faucet.
14. Connect the bottom (smallest tting) of the side spray diverter (10) to
the side spray supply hose (19).
16
12
2” (50 mm)
CONTENTS IN BOX
1 Faucet assembly
2 Rubber washer
3 Rubber washer
4 Plastic ange
5 Fixing plate
6 Fixing nut
12 Sealing washer
13 Side spray mounting ange
1
5
6
11
2
4
3
10
7
9
7 Supply hoses
8 Side spray supply hose
9 Side spray return hose
Side spray shower
11
14
16
8
13
19
17
15 Rubber washer
16 Plastic spacer
Rubber washer
14
18
20
21
Side spray diverter
10
17 Fixing plate
18 Fixing nut
19 Side spray supply hose
20 Weight
22
21 Screws
22 Key for aerator
12
15
17. Remove the aerator using the aerator key, turn on water, ush the
faucet for any debris and check for leaks.
Reinstall the aerator and ensure everything is functioning properly.