RUGO™ 2 700-301 PRODUCT MANUAL
TABLE OF CONTENTS INTRODUCTION Reference Guide 3 Overview 4 Physical Characteristics 4 POWER PACK Charging the Power Pack 5 Reassembling the Rugo™ 2 after Charging 6 Power Pack Life 6 Operational Modes 6 TRI-LENS™ Using the Tri-Lens™ 7 Removing the Tri-Lens ™ 7 REMOVING/CHANGING MOUNTS Removing the Standard Mount 8 Removing the ¼"-20 & Cold-Shoe Mount 8 MOUNTING TO DEVICES GoPro® 9 DSLR 9 Tripod/Puck Adaptor 9 MAINTENANCE Replacing the Seal 10 Removing the Guard 10 WARNINGS/
RUGO™ 2 REFERENCE GUIDE FULL ASSEMBLY ¼"-20 MOUNT GUARDS POWER/MODE SWITCH TRI-LENS™ CHARGE INDICATOR THUMBSCREWS DISASSEMBLED LIGHT HEAD DISASSEMBLED POWER PACK LOCKING POST LED CONTACT CAVITY (2) USB CHARGE PORT LED MODULE SCREW HOLE (4) “O”-RING ACCESS SCREW POWER CONTACTS MOUNTS INCLUDED THUMBSCREWS (2) ¼"–20 AND COLD-SHOE MOUNT STANDARD MOUNT WITH (2) KNOBS 3
OVERVIEW The Rugo™ 2 is a compact and powerful LED Light which has the ability to be mounted to the GoPro®, a DSLR, a drone, a tripod and many other devices. Having four different intensities (70–620 Lumens) with three interchangeable lens settings (Tri-Lens™), makes it a powerful tool for action sports as well as photography and filming. A Charge Indicator and Quick Swap™ Power Pack makes the Rugo™ 2, patents pending, one of a kind.
CHARGING THE POWER PACK 1 2 3 1 1. Press and hold the Power Pack Release Lever located on the Light Head portion of the Rugo™ 2. 2 2. While maintaining pressure on the Power Pack Release Lever, pull the Light Head and the Power Pack apart. If unable to pull apart easily (due to resistance of the internal rubber gasket), try moving the Power Pack back and forth while pulling apart. NOTE: Once apart, be sure to keep both ends dry and away from water, moisture and dust.
REASSEMBLING THE RUGO™ AFTER CHARGING 1 1. Install the Power Pack to the Light Head—confirm position of alignment posts to their respected cavities. 2 2. Push both halves together. A ‘click’ should be heard as they become locked together. Test the light to make sure that the Power Pack is properly connected to the Light Head by pressing the Power/Mode Switch. POWER PACK LIFE MODE DURATION LUMENS HIGH 1 hour 620 1.5 hours 380 6.75 hours 70 2.5 hours 620 MEDIUM LOW STROBE 1.
USING THE TRI-LENS™ The Rugo™ 2 Tri-Lens™ has three (3) beam emission angles which can be used for many different applications by simply sliding from left to right and viseversa. FLOOD SPOT AREA 120° 55° BEAM DISTANCE: 10 ft (3 m) USED FOR: Close-up BEAM DISTANCE: 30 ft (10 m) USED FOR: Mid-range 25° BEAM DISTANCE: 100 ft (30 m) USED FOR: Distance REMOVING THE TRI-LENS™ 1 2 1. 1 Push the Tri-Lens™ to either the right or left side until it won’t go any further.
REMOVING/CHANGING MOUNTS STANDARD MOUNT 1 2 3 1 1. Start with the Rugo™ 2 positioned so that the Thumbscrews are on top. 2 2. Twist each Thumbscrew counter-clockwise until they become loose. They should then be ready to pull out completely. 3 3. Once Thumbscrews are removed, the Standard Mount can then be disengaged from the Rugo™ completely. ¼"-20 AND COLD-SHOE MOUNT 1 8 2 3 1 1. Start with the Rugo™ 2 positioned so that the Thumbscrews are on top. 2 2.
MOUNTING TO DEVICES ACTION CAM The Rugo™ 2 can be mounted to an Action Cam via the removable Standard Mount. Line up the mounts on the Rugo™ with the mounts on the Action Cam and then tighten the Mount Knobs. NOTE: Orientation of Knobs should match as shown below. CAMERA The Rugo™ 2 can be mounted to a DSLR camera via the removable Cold-shoe Mount. Simply slide the mount onto the camera flash attachment and twist the Locking Ring until securely fastened.
MAINTENANCE REPLACING THE O-RING (P/N 51-112) 1 2 3 O-RING RETAINING TAB 1 1. Separate the Power Pack from the Light Head (follow steps 1–2 in the “Charging the Power Pack” section on page 5). 2. 2 Using a #2 Phillips head screwdriver (not included) remove the screw from the Light Head (reference “Disassembled Light Head” diagram on page 3). 3 3. The Retaining Tab and O-Ring can now be removed. If the O-Ring does not fall out on its own when unscrewed, it may need to be pulled out.
NOTES 11
WARRANTY AND OTHER INFORMATION PRODUCT DURABILITY WARNINGS FoxFury, LLC is not responsible for the incorrect use of any FoxFury Lighting product. 20 M 3M IPX7 PRODUCT NAME: Rugo™ 2 MODEL NUMBER: 700-301 ADAPTOR INPUT: AC 100-240V, 50/60 Hz CARE/CLEANING Your FoxFury product is a professional tool. Regular maintenance and care of your light will maximize performance for you. As needed, wash your FoxFury product using a soft washcloth, clean water and a mild soap.
This limited lifetime warranty is given only to the original end user of the accompanying product. If you purchased a product from someone other than an authorized FoxFury reseller/distributor or if the product was used, (including but not limited to demo models, show models or refurbished product by someone other than FoxFury) prior to your purchase, you are not the Original Purchaser and the product that you purchased is not covered by this warranty.
FOXFURY.
