Instructions / Assembly

Foundation Armor 2 Gallon Sprayer
3 Howe Drive, Suite 2
Amherst, NH 03031
866-306-0246
Warning: Improper use or failure to follow instructions can
result in explosive failure causing serious injury to the eyes, other
parts of the body, or people or items in the surrounding area. For safe
use of this product you must read and follow all safety instructions,
and use appropriate personal protective gear. Do not leave a
pressurized sprayer in the hot sun. Heat can cause pressure build-up
resulting in possible explosion. Do not store or leave chemicals or
liquids of any kind in tank after use. Clean immediately. Always
wear goggles, gloves, long sleeve shirt, long pants, full foot
protection, and any additional personal protective gear as required on
the Safety Data Sheet of the chemical/liquid you are spraying. Never
use any tool to remove pump if there is pressure in the sprayer.
Never stand with face or body over the top of the tank when
pumping or loosening pump to prevent ejecting pump assembly
and/or solution from striking and injuring you. Do not aim sprayer
nozzle at your face. Never pressurize sprayer by any means other
than the original pump. Do not attempt to modify this sprayer.
Replace parts only with manufacturer’s original parts. Never spray
flammable, caustic, acidic, chloring, bleach or other corrosive
solutions or heat, pressure, or gas producing chemicals. Always read
and follow chemical/liquid manufacturer’s instructions prior to use
with this sprayer as some chemicals/liquids may be hazardous when
used in this sprayer. Keep out of reach of children and pets. For
professional use. User is responsible for determining if sprayer is
appropriate for chemical/liquid being sprayed, as well as all actions
and consequences that can result from the use of the sprayer.
PARTS & PIECES
• (1) 0.5 GPM Adjustable Spray Cone Tip Nozzle
• (1) 1 GPM Fan Tip Nozzle
• (1) EPDM Rubber Hose
• (2) EPDM O-Ring
• (1) Viton O-Ring
• (1) 2 Gallon Stainless Steel Tank
• (1) Extension Wand
• (1) Holster Strap
• (1) O-Ring Lubricant
HOW TO USE
STEP 1: Attach hose to handle, tighten.
STEP 2: Attach nozzle to shut off handle or extension rod, tighten.
STEP 3: PRE-USE CHECKLIST
• Check tightness of hose nut to be sure hose is securely
attached to the tank outlet.
• Inspect the hose for deterioration, cracks, softness,
brittleness, or holes. If any of these conditions are found,
replace hose prior to use using only manufacturer’s parts.
• Remove the pump and inspect the interior and exterior of
the tank for signs of deterioration. Any sign of
deterioration indicates possible tank weakening and could
result in explosive bursting under pressure. If there are
any signs of deterioration, discard tank immediately and
replace. Do not attempt to patch leaks, cracks, wear, etc.,
as this could result in serious injury.
• Follow the FILLING, PRESSURIZING, and SPRAYING
instructions, using only air, to inspect for leaks. Maintain
20 PSI for 2-3 minutes. Direct shut-off away from you
and open to make sure discharge is not clogged. Ensure
pressure gauge is functioning and accurate. If unit passes
the leak and pressure test, empty tank and proceed with
FILLING, PRESSURIZING, and SPRAYING
instructions. If sprayer doesn’t pressurize with all parts
functioning and intact, discard sprayer.
• Inspect all metal parts including the wand, nozzle, and
fittings for rust, corrosion, pitting, and cracks. If any of
these conditions are found, replace affected part with
original manufacturer’s part before using.
• Ensure the appropriate O-Rings are installed in the
sprayer pump for the type of liquid being used. EPDM
rubber O-ring (currently installed in sprayer pump)
should be used for liquids containing acetone, such as the
Armor WL550, Armor SX5000, and Armor ultra-low
VOC acrylic sealers. Viton O-Ring should be used for
liquids containing Naphtha, such as the Armor AR350,
Armor AR500, Armor AX25, Armor AG Brown Seal,
Armor LV15, and Armor LV25. Water based liquids can
use either O-Ring. When changing pump O-Ring,
lubricate O-Ring prior to installing.
STEP 4: FILLING
• Turn the pump handle counterclockwise and remove
pump
• Prepare liquid following all directions and safety
information provided by the manufacturer of the liquid
being used.
• Fill the tank to no more than 2 gallons. DO NOT over fill
to accommodate the pump.
• Check the pump to make sure that no grass or dirt is stuck
to the barrel. Replace the pump in tank and tighten
securely.
STEP 5: PRESSURIZING
• Push handle down and turn clockwise until fully locked
and sealed.
• To pressurize, push handle down and turn ¼ turn
counterclockwise, then pump up and down until desired
pressure is achieved. Once desired pressure is achieved,
lock handle into place by pressing the handle down and
turning ¼ turn clockwise.
STEP 6: SPRAYING
• For consistent spraying, push down on the shut-off handle
and move locking mechanism away from you. To release,
squeeze handle and move the locking mechanism toward
you.
STEP 7: RELEASING PRESSURE
• With the pump pressure release valve facing away from
you, pull the release valve ring until air begins to escape.
Continue pulling escape valve ring until all pressure is
released from the sprayer.
STEP 8: CLEANING, CARE, STORAGE, AND MAINTENACE
• Immediately after spraying, clean the sprayer using the
instructions from the chemical/liquid manufacturer.
Follow the FILLING, PRESSURIZING, and SPRAYING
instructions, only do not fully pressurize. Do not allow
chemical/liquid to sit in the container. Do not clean the
tank with harsh liquids and chemicals such as Xylene,
MEK, or other similar chemicals. Warm soap and water,
or acetone are ok.
• Open the shut-off and allow the recommended cleaning
solution to run through the discharge assembly.
• Release the pressure according to the pressure release
instructions, remove pump, and empty sprayer.
• Store sprayer tank upside down, with pump removed, in a
warm and dry location.
• Periodically oil pump by dropping 10-12 drops of light
oil down pump rod through opening in cover.
SPRAYER USES
Sprayer is resistant to many liquids and chemicals, but not all. Using
a harsh liquid or chemical could result in the deterioration of seals or
hoses. If this happens, replace necessary parts as needed.
Best uses for this sprayer: water and solvent based acrylic sealers,
water repellent sealers, concrete densifiers and surface hardeners,
some pesticides, and some cleaning solutions.