ＫＯＮＦＯＲ ＳＰＳ－ ９１３ＢＷ User Manual Ultrasonic Mist Humidifier
* Read all the safety instructions carefully before use and keep this instruction manual for future reference: Warning: Please be aware of the following points or you might be in danger of high voltage charges or burn your body. 1) N e v e r d i s a s s e m b l e t h e b a s e u n i t w i t h o u t consulting qualified personnel. 2) If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
11) Never scrape Transducer cpl on your own. 12) Never clean Transducer cpl with detergents or chemical solutions that are not made by our company. 13) Never let water splash into inner base unit to avoid components damage. 14) Care should be taken when using the appliance due to emission of hot water vapor. 15) Before cleaning and maintenance, the appliance must be disconnected from the power supply. 16) Prior to cleaning or other maintenance , the appliance must be disconnected from the supply mains.
*Working Principle: Ultrasonic Humidifier uses the ultrasonic high-frequency oscillator to break up water into tiny water particles with the diameter of about 1-5um.The ventilation system blows out this water into the dry air where they evaporate to give the required humidity. The clearly visible smooth and even fog can be seen out of the unit. *Features: High efficient in humidification with large output. Low energy consumption, save 85-90 percent of electricity than normal stream humidifier.
*Correct Humidity Level: What exactly is relative humidity: Relative humidity is the amount of water vapor in the air, expressed as a percentage of the maximum amount that the air could hold at the given temperature.. We normally mark it with ％RH, like 45％RH. Atomosphereic air always contains water vapor, the percentage of which depends on the meterological conditions. The higher the temperature is the more the air keeps water vapor. Therefore, we use the concept of ‘relative humidity”.
*Operation Instruction First Operation, put unit in the room temperature for half of an hour before running. It is recommended to use the unit under temperature of 20 degree C, relative humidity less than 80％RH. Use clear water not over 40 degree C Check the water basin, make sure it is clear. 1. Put the machine on a flat surface. 3. Put the water tank on the main base. 2. Fill the water into the water tank, and then tighten the tank cover.
* FUNCTIONS 1: Relative Humidity 1. The percentage of water mist in a given space with a given air temperature is named as relative humidity, usually marked as %RH, i.e. 45%RH. The air contains water mist more or less. The proportion of water mist to the air varies according to different air temperatures. The higher the temperature, the more water mist inhaled in the air. 2. In the winter, the cold air outside enters the room and becomes warmer by the higher temperature in the room.
INSTRUCTIONS FOR USAGE: 1. Put the machine on a flat surface. 2. Fill the water into the water tank, and then tighten the tank cover. 3. Put the water tank on the main base. 4. Check if the rated voltage meets the input voltage, and plug into the socket. Then display shows the symbol POWER 5 . Touch the symbol POWER on the machine, the background LED light will be on. The machine will begin to work in AUTO mode. Display shows AUTO symbol and current humidity, temperature.
The device checks the accordance of the temperature level and the humidity level every 1 minute. 6 . Touch the symbol MODES baby mode and auto mode , to choose health mode, In health mode: a) WARM MIST is on. Display show the health mode symbol , warm mist symbol The device starts to achieve humidity 60% at maximum power . b) After the humidity 60% is achieved, the device works at minimal power. c) Only TIMER SETING function is operable in healthy mode.
you set the expected humidity, the machine will keep the memory and confirm after 5 seconds. The LED display shows the symbol and current humidity. Touch again, it shows the expected humidity setting. If the expected humidity is less than the current humidity, the machine will be in sleeping state. But if the expected humidity is 3% higher than the current humidity, the humidify function will work. Mist output speed cannot be setting during the constant humidity model. 9 .
Operation steps • Take the water tank out of the unit, open the water tank cover and fill the tank with clear water. Close the cover and put the tank onto the base unit carefully. • Put the nozzle into the socket on top of the water tank. • Connect the power supply, switch on the unit (NEVER RUN THE UNIT WHEN THERE IS NO WATER IN WATER BASIN), the main connection lamp will on. The unit will begin working. Connect To The Mobile Client 1. Configure the network. ——Quick Connect mode 2.
Connect to the mobile client ——Hotspot Mode 1. Connect your phone to WiFi, scan the QR code below, or search for “ProscenicHome” in the app store to download the app. 2. In the power-on state, long press the key “ ” 66 seconds until the WiFi indicator “ ” Slow flash.
TECHNICAL DATA • • • • Model: SPS-913BW Power supply: 110-120V 50/60Hz Heating power: 80W Humidify power: 30W • • • • Total power: 110W Water tank capacity: 5L Evaporation Rate: ≥300mL/h Noise level: ≤35dB(A) Maintenance Instruction Maintenance In a case when the water is hard which means water contains too much calcium and magnesium, it can cause a “white powder” problem and leave heavy scales on the surface of water basin, transducer and inner surface of the water tank.
Trouble Shooting Guide Trouble Shooting Guide If any trouble is found in normal operation, please kindly refer to the following points: Trouble Possible reasons Solution Power lamp off, does not work No power supply Connect power supply, switch on Power lamp on, no mist outlet with wind 1. No water in water tank 2. Security switch is too loose 1. Fill water into water tank 2. Tighten the switch Abnormal smell mist 1. New unit 2. Dirty water or water sitting too long 1.
ＫＯＮＦＯＲ Ｆｏｓｈａｎ Ｓａｍｙｏｏ Ｅｌｅｃｔｒｏｎｉｃ Ｃｏ．，Ｌｔｄ Ａｄｄ ： Ｊｉａｎｇｃｕｎ Ｉｎｄｕｓｔｒｉａｌ Ｚｏｎｅ ，Ｌｅｌｉｕ ，Ｓｈｕｎｄｅ Ｆｏｓｈａｎ， Ｇｕｇｎａｇｄｏｎｇ ， Ｐ．Ｒ．Ｃｈｉｎａ Ｔｅｌ ：０７５７－ ２８６０１７００ Ｆａｘ ：０７５７－ ２８６０１７１１
FCC STATEMENT : This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
