ＫＯＮＦＯＲ ＳＰＳ－ ８０７Ｗ User Manual Ultrasonic Mist Humidifier
Catalog Attentions 1-2 Attentions & Working Principle and Characteristics 2 Humidity introduction and function 3 Operating steps 4-6 Connect to mobile client 6-8 Maintenance Instruction 9 Trouble Shooting Guide 10
Attentions Thank you for purchasing your new Ultrasonic Humidifier. The humidifier helps you to restore an appropriate level of humidity and eliminate the discomfort associated with dry air. We wish you many years of healthy indoor air with this efficient and effective product. We recommend you spend some time reading this instruction manual in order to fully understand all the operational features it offers.
Attentions & Working Principle and Characteristics 15). Before cleaning and maintenance, the appliance must be disconnected from the power supply. 16). Prior to cleaning or other maintenance, the appliance must be disconnected from the supply mains. 17). This appliance can be used by children aged from 8 years and above if they have been given supervision or instruction concerning use of the appliance in a safe way and if they understand the hazards involved.
Humidity Introduction and Function Correct Humidity Level What exactly is relative humidity: Relative humidity is the amount of water vapor in the air, expressed as a percentage of the maximum amount that the air could hold at the given temperature.. We normally mark it with ％ RH, like 45％RH. Atomosphereic air always contains water vapor, the percentage of which depends on the meterological conditions. The higher the temperature is the more the air keeps water vapor.
Operating Steps Operation Instruction First Operation, put unit in the room temperature for half of an hour before running. It is recommended to use the unit under temperature of 20 degree C, relative humidity less than 80％RH. Use clear water not over 40 degree C Check the water basin, make sure it is clear. INSTRUCTIONS FOR USAGE 1. Put the machine on a flat surface. 2. Fill the water into the water tank, and then tighten the tank cover. Temperature 3. Put the water tank on the main base. Humidity 4.
Operating Steps 5. Touch the symbol POWER “ ” on the machine; the background LED light will be on. The machine will begin to work in AUTO mode. Display shows AUTO symbol. After 15 seconds without any operation, the display will become dim, press any key except power key to wake up the display. Temperature of the air, degrees Celsius ≤19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 ≥37 Humidity(%) 65 60 58 57 55 53 50 48 45 43 40 38 36 35 34 32 31 30 25 6.
Operating Steps & Connect To Mobile Client 12. Slide the symbol MAX-MIN “ ” , AUTO mode is cancelled and the mist output is in the first speed. You may select 7 desired levels of mist volume. The corresponding strip symbol will appear on the display. 5 seconds after setting mist output speed, the current room humidity will appear on the display as well. On the remote control, just to press symbol “ ” to select mist output level and AUTO mode in different times. 13.
Connect To Mobile Client Add device Add device Change network confirm Add device Confirmation indicator 4. APP add device: turn on the APP, select add humidifier device and confirm WiFi indicator “ ” flash. 5. erform network configuration. According to the APP page prompt, select and enter the WiFi password to make the device enter the connection state and wait for the distribution network to complete. * Note: the host does not support 5.8g band WiFi network.
Connect To Mobile Client & Parameters Add a Device AP mode Please select the purchased device make sure the WiFi indicator flashes slowly Add a Device AP mode Please select the p LDS-xxxx make sure the WiFi indicator flashes slowly 807C ...... M7 H500 807C H600 ...... indicator flashes slowly Click or pull up to load more 3. Add a humidifier device to the app, switch to the hotspot mode, and confirm that the WiFi indicator is in a slow flashing state. Setting 4.
Maintenance Instruction Maintenance In a case when the water is hard which means water contains too much calcium and magnesium, it can cause a “white powder” problem and leave heavy scales on the surface of water basin, transducer and inner surface of the water tank. Scales on the surface of transducer will let the unit work improperly. We recommend 1). Use cold boiled water or distilled water. 2). Clean the transducer, water tank and basin unit every week. 3) .
Trouble Shooting Guide Trouble Shooting Guide If any trouble is found in normal operation, please kindly refer to the following points: Trouble Possible reasons Solution Power lamp off, does not work No power supply Connect power supply, switch on Power lamp on, no mist outlet with wind 1. No water in water tank 2. Security switch is too loose 1. Fill water into water tank 2. Tighten the switch Abnormal smell mist 1. New unit 2. Dirty water or water sitting too long 1.
Ａｄｄ ： ＫＯＮＦＯＲ Ｆｏｓｈａｎ Ｓａｍｙｏｏ Ｅｌｅｃｔｒｏｎｉｃ Ｃｏ．，Ｌｔｄ Ａｄｄ ： Ｊｉａｎｇｃｕｎ Ｉｎｄｕｓｔｒｉａｌ Ｚｏｎｅ ，Ｌｅｌｉｕ ，Ｓｈｕｎｄｅ Ｆｏｓｈａｎ， Ｇｕｇｎａｇｄｏｎｇ ， Ｐ．Ｒ．Ｃｈｉｎａ Ｔｅｌ ：０７５７－ ２８６０１７０１ Ｆａｘ ：０７５７－ ２８６０１７１１
FCC STATEMENT : This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
