User’s Manual FOS Luminus Table USER’S MANUAL Before you operate this fixture read the manual carefully. Always make sure to include the manual if you pass/rent/sell the fixture to another user.
User’s Manual TABLE OF CONTENT 1. WARNING ………………………………….….…….…………………………….………………………………………….2 1.1 Safety Instructions ………………………………………………….……………………………………………………….2 1.2 Rigging …………………………………………………………………………………………………………………….….…3 2. PRODUCT INTRUDUCTION …………………………………………………………………………….……………3 2.1 Items Included in the Tour Pack. ….…………………………….…….…….…….…………………….……..........3 2.2 Product Overview…………………………………………………………………….……………………………………….3 2.2.1 Fixture Elements and Connectors …………………………………….………………….……………….4 2.2.
User’s Manual 1. WARNING 1.1 Safety Instructions This product guide contains important information about the safe installation and use of this product. Please read and follow these instructions carefully and keep this manual in a safe place for future reference. When unpacking and before disposing of the carton, check there is no transportation damage before using the product. Should there be any damage caused by transportation, consult your dealer and do not use the apparatus.
User’s Manual IMPORTANT: The manufacturer will not accept liability for any resulting damages caused by the non-observance of this manual or any unauthorized modification to the fixture. 1.2 Rigging Concerning rigging, trussing for this fixture, please follow the European and national guidelines. Only the qualified technicians are allowed for the device installation, The fixture must never be mounted for a possible swinging position, and a safety cord attached must always be used. 2.
User’s Manual hours in auto run mode and around 12 hours in running single color. Table light Q6 can operate in wireless DMX mode, Master/Slave mode, and also in auto run mode. IR controller is supplied to make remote control as well. Its magnetic base helps it to stand right in the center of table or on any metal surface. You can also put it on top of metal spike in your garden as a garden light. Table light Q6 is rated IP54. It is therefore suitable for indoor and outdoor applications. 2.2.
User’s Manual 1. Menu to select the programming functions 2. Enter Enter the current menu or confirm the current function value 3. Up Scroll “UP” through the menu list to increase the value of the current function 4. Down Scroll “DOWN” through the menu list to decrease value of the current function 2.2.3 Fixture Dimensions Fixture Tour Pack 2.3 Storing the Fixture Make sure to fully charge all fixtures before storing. Partially charged batteries will lose capacity.
User’s Manual 2.4 Specifications Electrical Power input Power consumption Power input/output connector 100-240VAC 50/60Hz 15W max. Magnetic DC connector Battery Battery Charge time Battery life 11.1V 8.8Ah About 4.
User’s Manual 3 INSTALLATION The fixture can be mounted to any metal surface. 3.1 The table light can be placed on the enclosed metal plate on dinner table. Put the metal plate on dinner table or underneath tablecloth, put your table light to the center of the metal plate. 3.2 The table light can also be attachd to any solid metal surface. Make sure the surface is flat and table light magnetic base can be attached to it safely. 3.
User’s Manual 4. BATTERY CHARGE The fixture has a rechargeable lithium battery built in. Always store the fixtures with full battery. Depleted batteries must be recharged immediately; otherwise fixture performance will suffer. Battery runtime will decreased time by time. Battery runtime may be slightly shorter than predicted due to different working enviroments. The fixture has a magnetic DC charge connector.
User’s Manual 5.
User’s Manual 5.2 DMX Addressing Each fixture must be given a DMX address so that the correct fixture responds to the correct control signals. This DMX address is the channel number from which the fixture starts to “listen” to the digital control information being sent out from the controller. This fixture has 3 DMX channel modes, 4, 6 and 10 DMX channels. To set up fixture DMX address, first select DMX channel mode. The highest DMX address for this fixture is 512.
User’s Manual 5.3.2 Connect Fixture to a Wireless DMX Transmitter After fixture is switched on, and if there is no new transmitter, fixture will connect to the old transmitter automatically, no need to re-connect it. To put table light into wireless DMX, receive mode, press MENU button repeatedly until you see “Wireless DMX”, press ENTER to select [ Transmit] / [ Receive]. Press UP/DOWN to select [ Receive], and press ENTER to save the setting.
User’s Manual 5.4 OLED Display Protection OLED display can be set to turn off in 10-30 second or always “On”. Follow below steps: - Continue pressing “MENU” till “Back Light” appears. - Press “ENTER” you will see “Always On”, you can scroll up/down to set up the time for OLED display back light to turn off, or always “On” - Press “ENTER” to save your setting. 5.5 ECO Mode Fixture can be set to operate at ECO mode.
User’s Manual 6. OPERATION 6.1 DMX Control Mode This function will allow users to control individual fixture with a standard DMX 512 console. Below is fixture DMX Channel Chart.
User’s Manual 236-240 White 8 241-245 White 9 246-250 White 10 251-255 White 11 0-5 No function 6-25 R:255 G:215 B:076 A:251 26-50 R:255 G:236 B:095 A:252 51-75 R:249 G:249 B:108 A:253 76-100 R:229 G:255 B:125 A:239 Color 101-125 R:197 G:242 B:133 A:207 temperature 126-150 R:187 G:235 B:136 A:191 151-175 R:169 G:236 B:148 A:207 176-200 R:168 G:240 B:156 A:204 201-225 R:167 G:244 B:165 A:201 226-250 R:167 G:255 B:183 A:192 251-255 No function 0
User’s Manual - Press “UP” or “DOWN” to scroll up/down to select “Auto”; - Press “ENTER” to select from “Program 1” to “Program 4”; - Press ENTER to confirm your setting; - Press ENTER again to adjust auto run speed (from 01 -09). To exit out of any above options, press MENU button. 6.4 Customized Colors Users are allowed to program their own color effects and save to the fixture. Follow the steps below: - Press button “MENU” repeatedly until “Custom” appears.
User’s Manual the fixture. 1 - Set the fixture into blackout (LED on/off). 2 - Adjust auto, strobe & fade speed, sound sensitivity, DMX address, DMX channel, brightness etc. 3 - Run auto mode, use “Speed” button followed by the buttons to adjust auto speeds. 4 – Run sound program, use buttons to adjust sound sensitivity. 5 – Run strobe program, use buttons to adjust strobe speed. 6 – Set auto/fade speed, Press this button followed by buttons to adjust program speed.
User’s Manual The fixture has optical lenses; users should clean the lenses periodically to optimize light output. The cleaning frequency depends on the environment in which the curtain system is installed. Damp, smoky or particularly dirty surrounding can cause greater accumulation of dirt on the lenses. Even in a clean type of surroundings, it is suggested to clean the lens and housing at least once a month. It is suggested to use a soft cloth using normal glass cleaning fluid.
User’s Manual Memo: ______________________________________________________________________________________ ______________________________________________________________________________________ ______________________________________________________________________________________ ______________________________________________________________________________________ ______________________________________________________________________________________ ________________________________________________________
User’s Manual FOS Luminus Table USER’S MANUAL Dealer Info. Copyright reserved Manual version: Ver. 1.
