26" CITY BREEZE LADIES ELECTRIC BIKE FS26LDEBKSA
SAFETY & WARNINGS Electric Assisted Bike Regulations The EN 15194 EU standard or EPAC (Electric Power Assisted Cycle) conforms to the following characteristics for electric power assisted bikes: • Motor assistance only starts when the cyclist pedals. • The assistance cuts out as soon as the cyclist stops pedalling. • The assistance cuts out as soon as the speed exceeds 25km/h.
14. Store the battery in a dry place after having completely recharged it. Avoid extreme temperatures (both low and high) as they can damage the battery. Optimal operating range: -10°C to 35°C. Cleaning and Maintenance • • • • • Use a damp cloth with neutral detergent to clean the bike frame. Do not use any detergents or cleaning liquids liable to deteriorate the frame or components.
OVERVIEW Basic overview Handle grips Control pad Bell Brake lever Handlebars Seat Handlebar stem Battery Rack Headlight Seatpost clamp Front brakes Bike frame Rear sprocket Fork Pedals Rear wheel Crankset Chain Front wheel
ASSEMBLY Stem & Handlebar Assembly WARNING: To prevent steering system damage and possible loss of control, the stem must be inserted enough so that the minimum insertion marks are completely covered (see Figure 1). Minimum insertion mark Figure 1 Remove the plastic shipping cap from the bottom of the stem; insert the stem and handlebar assembly into the fork, making sure the stem wedge is loose. Ensure the cables are not tangled and track smoothly on either side of the stem.
Wheel Mounting 1. 2. 3. 4. 5. 6. Make sure the brakes are loose enough to allow the wheel to pass through the brake pads easily. If not already loose, disconnect the front brake by detaching the cable guide from the carrier. Place wheel into fork dropouts (Figure 3a) Install retaining washers with raised lip pointed towards the fork and insert into the small hole of the fork blade. Install axle nut and securely tighten (Figures 3a and 3b). Make sure the wheel is centred between the fork blades.
Seat Assembly 1. 2. 3. 4. Insert the seat stem into the frame (see Figure 5). Pull the quick-release lever free and insert the seat-post to the minimal insertion marker indicated on the seat-post. Insert at least to the minimal indication on the seat stem using rotary movements. You can use grease to help assembly. Tighten the quick-release clamp and then fold the lever to closed position. Minimal torque specifications are 19.5Nm.
BEFORE FIRST USE Recommendations and Component Control before Use Before using your bicycle for the first time, you must check that all adjustments have been correctly made. • Check that the front and rear brakes work, check brake pads for wear. • Check the cables and sheaths and that the hydraulic system functions correctly. Wheels and Tires • Check tires are inflated to the pressure indicated (either in Bar or Psi) on the tire sidewall.
Bearings • • • Check that all bearings are properly adjusted, and apply lubricant if needed. Ensure they are not too loose, and that they have not seized up. Check steering bearings, wheel bearings, pedal bearings and bottom bracket bearings. Crank set and Pedals • Make sure that the pedals are correctly tightened and that the teeth of the crank set do not show any unusual wear. Accessories • Check front and rear lights; also check that bell is working.
OPERATION Presentation and Electrical Start-Up ELECTRONIC PAD LAYOUT – (A): Less assistance M (B): Mode On/Off + (C): More assistance Starting System 1. Press the Mode On/Off button (B) for 5 seconds in order to start the system or shut the system off. 2. Hold + Button (C) for 3 seconds to turn on the light, hold again for another 3 seconds to turn off the light. 3. When the vehicle is stationary, long press – Button (A) to enter the 6KM/h walk mode. Walk mode is in effect while the button is held.
Battery Mounting and Locking Use the battery key which supplied in carton to take out the battery. Use the battery key to fix the battery. Press the power display button on the battery to check the battery volume. Battery Charging With the supplied charger, you can charge the battery directly whilst it is on the bike or use the key to take out the battery; the connection plug is located at the top of the battery.
CLEANING & CARE Care and Lubrication Only use specific bicycle lubricants. Pedals A few drops every 6 months on the axle. Chain Spray the whole surface every 6 months. Bottom bracket Every 6 months, please check with your authorised dealer. Motor Every year, please check with your authorised dealer. Maintenance and Advice 1. Never modify your bicycle with non-certified parts. 2. Never ride in deep water. 3. Do not use for jumps or stunts (apart from downhill or endure bicycles). 4.
SPECIFICATIONS Power supply 36V Instrument rated working current 10mA Maximum working current of the instrument 30mA Shutdown leakage current <1uA Supply the working current of the controller Max 500mA Using temperature -20~60°C Storage temperature -30~70°C
NOTES
Need more information? We hope that this user guide has given you the assistance needed for a simple set-up. For the most up-to-date guide for your product, as well as any additional assistance you may require, head online to help.kogan.com.
