User manual
Table Of Contents
- Introduction
- Product Overview
- Installation and Quick Startup
- Package Contents
- Switch Installation
- Installing the Switch in a Rack
- Quick Starting the Switch
- System Information Setup
- Quick Start up Software Version Information
- Quick Start up Physical Port Data
- Quick Start up User Account Management
- Quick Start up IP Address
- Quick Start up Uploading from Switch to Out-of-Band PC
- Quick Start up Downloading from Out-of-Band PC to Switch
- Quick Start up Downloading from TFTP Server
- Quick Start up Factory Defaults
- Console and Telnet Administration Interface
- Web-Based Management Interface
- Command Line Interface Structure and Mode-based CLI
- Switching Commands
- System Information and Statistics commands
- Device Configuration Commands
- Interface
- L2 MAC Address and Multicast Forwarding Database Tables
- VLAN Management
- Double VLAN commands
- GVRP and Bridge Extension
- IGMP Snooping
- IGMP Snooping Querier
- MLD Snooping
- MLD Snooping Querier
- Port Channel
- Storm Control
- L2 Priority
- Port Mirror
- Link State
- Port Backup
- FIP Snooping
- Enhanced Transmission Selection (ETS)
- Congestion Notification
- Management Commands
- Spanning Tree Commands
- System Log Management Commands
- Script Management Commands
- User Account Management Commands
- Security Commands
- CDP (Cisco Discovery Protocol) Commands
- SNTP (Simple Network Time Protocol) Commands
- MAC-Based Voice VLAN Commands
- LLDP (Link Layer Discovery Protocol) Commands
- Denial Of Service Commands
- VTP (VLAN Trunking Protocol) Commands
- Protected Ports Commands
- Static MAC Filtering Commands
- System Utilities
- DHCP Snooping Commands
- IP Source Guard (IPSG) Commands
- Dynamic ARP Inspection (DAI) Command
- Differentiated Service Command
- ACL Command
- IPv6 ACL Command
- CoS (Class of Service) Command
- Domain Name Server Relay Commands
- Routing Commands
- IP Multicast Commands
- IPv6 Commands
- Web-Based Management Interface
- Overview
- System Menu
- View ARP Cache
- Viewing Inventory Information
- Configuring Management Session and Network Parameters
- Defining Forwarding Database
- Viewing Logs
- Managing Switch Interface
- Defining sFlow
- Defining SNMP
- Viewing Statistics
- Managing System Utilities
- Managing CDP Function
- Defining Trap Manager
- Configuring SNTP
- Defining DHCP Client
- Defining DNS Relay Function
- Switching Menu
- Managing DHCP Snooping
- Managing IP Source Guard (IPSG)
- Managing Dynamic ARP Inspection (DAI)
- Managing Filters
- Managing Port-based VLAN
- Managing Protected Ports
- Managing Protocol-based VLAN
- Managing IP Subnet-based VLAN
- Managing MAC-based VLAN
- Managing MAC-based Voice VLAN
- Managing Voice VLAN
- Defining GARP
- Managing IGMP Snooping
- Managing IGMP Snooping Querier
- Managing MLD Snooping
- Managing MLD Snooping Querier
- Managing Port-Channel
- Viewing Multicast Forwarding Database
- Managing Spanning Tree
- Defining 802.1p priority
- Managing Port Security
- Managing LLDP
- Managing LLDP-MED
- Managing VTP
- Managing Link State
- Managing Port-Backup
- Managing FIP-Snooping
- Routing Menu
- Security Menu
- IPv6 Menu
- Configuring IPv6 Global Configuration Page
- Configuring IPv6 Interface Configuration Page
- Viewing IPv6 Interface Summary Page
- Viewing IPv6 Interface Statistics Page
- Viewing IPv6 Neighbor Table Information Page
- Viewing IPv6 Static Neighbor Table Information Page
- Managing OSPFv3 Protocol
- Managing IPv6 Routes
- Managing RIPv6
- QOS Menu
- IPv4 Multicast Menu
- IPv6 Multicast Menu
- 597 -
None
Command Mode
Router OSPFv3 Config
10.5 RIPng Commands
RIPng is intended to allow routers to exchange information for computing routes through an IPv6-based
network. RIPng is a distance vector protocol. RIPng should be implemented only in routers. Any router
that uses RIPng is assumed to have interfaces to one or more networks, otherwise it isn’t really a router.
These are referred to as its directly-connected networks. The protocol relies on access to certain
information about each of these networks, the most important of which is its metric. The RIPng metric of a
network is an integer between 1 and 15, inclusive. It is set in some manner not specified in this protocol;
however, given the maximum path limit of 15, a value of 1 is usually used. Implementations should allow
the system administrator to set the metric of each network. In addition to the metric, each network will
have an IPv6 destination address prefix and prefix length associated with it. These are to be set by the
system administrator in a manner not specified in this protocol.
10.5.1 Show Commands
10.5.1.1 show ipv6 rip
This command displays information relevant to the RIPng router
Syntax
show ipv6 rip
Default Setting
None
Command Mode
Privileged Exec
Display Messages
RIPng Admin Mode: Select enable or disable from the pulldown menu. If you select enable RIPng
will be enabled for the switch. The default is disabled.
Split Horizon Mode: Select none, simple or poison reverse from the pulldown menu. Split horizon is
a technique for avoiding problems caused by including routes in updates sent to the router from which
the route was originally learned. The options are: None - no special processing for this case. Simple -
a route will not be included in updates sent to the router from which it was learned. Poisoned reverse
- a route will be included in updates sent to the router from which it was learned, but the metric will be
set to infinity. The default is simple.
Default Metric: Sets a default for the metric of redistributed routes. This field displays the default
metric if one has already been set or blank if not configured earlier. The valid values are (1 to 15).
Default Route Advertise: The default route.