User manual
Table Of Contents
- Introduction
- Product Overview
- Installation and Quick Startup
- Package Contents
- Switch Installation
- Installing the Switch in a Rack
- Quick Starting the Switch
- System Information Setup
- Quick Start up Software Version Information
- Quick Start up Physical Port Data
- Quick Start up User Account Management
- Quick Start up IP Address
- Quick Start up Uploading from Switch to Out-of-Band PC
- Quick Start up Downloading from Out-of-Band PC to Switch
- Quick Start up Downloading from TFTP Server
- Quick Start up Factory Defaults
- Console and Telnet Administration Interface
- Web-Based Management Interface
- Command Line Interface Structure and Mode-based CLI
- Switching Commands
- System Information and Statistics commands
- Device Configuration Commands
- Interface
- L2 MAC Address and Multicast Forwarding Database Tables
- VLAN Management
- Double VLAN commands
- GVRP and Bridge Extension
- IGMP Snooping
- IGMP Snooping Querier
- MLD Snooping
- MLD Snooping Querier
- Port Channel
- Storm Control
- L2 Priority
- Port Mirror
- Link State
- Port Backup
- FIP Snooping
- Enhanced Transmission Selection (ETS)
- Congestion Notification
- Management Commands
- Spanning Tree Commands
- System Log Management Commands
- Script Management Commands
- User Account Management Commands
- Security Commands
- CDP (Cisco Discovery Protocol) Commands
- SNTP (Simple Network Time Protocol) Commands
- MAC-Based Voice VLAN Commands
- LLDP (Link Layer Discovery Protocol) Commands
- Denial Of Service Commands
- VTP (VLAN Trunking Protocol) Commands
- Protected Ports Commands
- Static MAC Filtering Commands
- System Utilities
- DHCP Snooping Commands
- IP Source Guard (IPSG) Commands
- Dynamic ARP Inspection (DAI) Command
- Differentiated Service Command
- ACL Command
- IPv6 ACL Command
- CoS (Class of Service) Command
- Domain Name Server Relay Commands
- Routing Commands
- IP Multicast Commands
- IPv6 Commands
- Web-Based Management Interface
- Overview
- System Menu
- View ARP Cache
- Viewing Inventory Information
- Configuring Management Session and Network Parameters
- Defining Forwarding Database
- Viewing Logs
- Managing Switch Interface
- Defining sFlow
- Defining SNMP
- Viewing Statistics
- Managing System Utilities
- Managing CDP Function
- Defining Trap Manager
- Configuring SNTP
- Defining DHCP Client
- Defining DNS Relay Function
- Switching Menu
- Managing DHCP Snooping
- Managing IP Source Guard (IPSG)
- Managing Dynamic ARP Inspection (DAI)
- Managing Filters
- Managing Port-based VLAN
- Managing Protected Ports
- Managing Protocol-based VLAN
- Managing IP Subnet-based VLAN
- Managing MAC-based VLAN
- Managing MAC-based Voice VLAN
- Managing Voice VLAN
- Defining GARP
- Managing IGMP Snooping
- Managing IGMP Snooping Querier
- Managing MLD Snooping
- Managing MLD Snooping Querier
- Managing Port-Channel
- Viewing Multicast Forwarding Database
- Managing Spanning Tree
- Defining 802.1p priority
- Managing Port Security
- Managing LLDP
- Managing LLDP-MED
- Managing VTP
- Managing Link State
- Managing Port-Backup
- Managing FIP-Snooping
- Routing Menu
- Security Menu
- IPv6 Menu
- Configuring IPv6 Global Configuration Page
- Configuring IPv6 Interface Configuration Page
- Viewing IPv6 Interface Summary Page
- Viewing IPv6 Interface Statistics Page
- Viewing IPv6 Neighbor Table Information Page
- Viewing IPv6 Static Neighbor Table Information Page
- Managing OSPFv3 Protocol
- Managing IPv6 Routes
- Managing RIPv6
- QOS Menu
- IPv4 Multicast Menu
- IPv6 Multicast Menu
- 559 -
<gateway-address> - Gateway address in IPv6 global or link-local address format.
no – Use this command remove IPv6 gateways on the network port interface.
Command Mode
Interface vlan
10.3.2.7 ipv6 route
Use this command to configure an IPv6 static route. The <ipv6-prefix> is the IPv6 network that is the
destination of the static route. The <prefix_length> is the length of the IPv6 prefix — a decimal value
(usually 0-64) that shows how many of the high-order contiguous bits of the address comprise the prefix
(the network portion of the address). A slash mark must precede the <prefix_length>. The
<next-hop-address> is the IPv6 address of the next hop that can be used to reach the specified network.
The <preference> parameter is a value the router uses to compare this route with routes from other route
sources that have the same destination. The range for <preference> is 1 - 255, and the default value is 1.
The interface <slot/port> identifies direct static routes from point-to-point and broadcast interfaces, and
must be specified when using a link-local address as the next hop. A route with a preference of 255
cannot be used to forward traffic.
Syntax
ipv6 route <ipv6-prefix>/<prefix_length> {<next-hop-address> [<preference>] | interface <slot/port>
<next-hop-address> [<preference>]}
no ipv6 route <ipv6-prefix>/<prefix_length> [{<next-hopaddress> | interface
<slot/port> <next-hop-address> | <preference>}]
no – Use this command to delete an IPv6 static route. Use the command without the optional
parameters to delete all static routes to the specified destination. Use the <preference> parameter to
revert preference of a route to default preference.
Default Setting
Disabled
Command Mode
Global Config
10.3.2.8 ipv6 route distance
This command sets the default distance (preference) for IPv6 static routes. Lower route distance values
are preferred when determining the best route. The ipv6 route command allows you to optionally set the
distance (preference) of an individual static route. The default distance is used when no distance is
specified in this command.