User manual
Table Of Contents
- Introduction
- Product Overview
- Installation and Quick Startup
- Package Contents
- Switch Installation
- Installing the Switch in a Rack
- Quick Starting the Switch
- System Information Setup
- Quick Start up Software Version Information
- Quick Start up Physical Port Data
- Quick Start up User Account Management
- Quick Start up IP Address
- Quick Start up Uploading from Switch to Out-of-Band PC
- Quick Start up Downloading from Out-of-Band PC to Switch
- Quick Start up Downloading from TFTP Server
- Quick Start up Factory Defaults
- Console and Telnet Administration Interface
- Web-Based Management Interface
- Command Line Interface Structure and Mode-based CLI
- Switching Commands
- System Information and Statistics commands
- Device Configuration Commands
- Interface
- L2 MAC Address and Multicast Forwarding Database Tables
- VLAN Management
- Double VLAN commands
- GVRP and Bridge Extension
- IGMP Snooping
- IGMP Snooping Querier
- MLD Snooping
- MLD Snooping Querier
- Port Channel
- Storm Control
- L2 Priority
- Port Mirror
- Link State
- Port Backup
- FIP Snooping
- Enhanced Transmission Selection (ETS)
- Congestion Notification
- Management Commands
- Spanning Tree Commands
- System Log Management Commands
- Script Management Commands
- User Account Management Commands
- Security Commands
- CDP (Cisco Discovery Protocol) Commands
- SNTP (Simple Network Time Protocol) Commands
- MAC-Based Voice VLAN Commands
- LLDP (Link Layer Discovery Protocol) Commands
- Denial Of Service Commands
- VTP (VLAN Trunking Protocol) Commands
- Protected Ports Commands
- Static MAC Filtering Commands
- System Utilities
- DHCP Snooping Commands
- IP Source Guard (IPSG) Commands
- Dynamic ARP Inspection (DAI) Command
- Differentiated Service Command
- ACL Command
- IPv6 ACL Command
- CoS (Class of Service) Command
- Domain Name Server Relay Commands
- Routing Commands
- IP Multicast Commands
- IPv6 Commands
- Web-Based Management Interface
- Overview
- System Menu
- View ARP Cache
- Viewing Inventory Information
- Configuring Management Session and Network Parameters
- Defining Forwarding Database
- Viewing Logs
- Managing Switch Interface
- Defining sFlow
- Defining SNMP
- Viewing Statistics
- Managing System Utilities
- Managing CDP Function
- Defining Trap Manager
- Configuring SNTP
- Defining DHCP Client
- Defining DNS Relay Function
- Switching Menu
- Managing DHCP Snooping
- Managing IP Source Guard (IPSG)
- Managing Dynamic ARP Inspection (DAI)
- Managing Filters
- Managing Port-based VLAN
- Managing Protected Ports
- Managing Protocol-based VLAN
- Managing IP Subnet-based VLAN
- Managing MAC-based VLAN
- Managing MAC-based Voice VLAN
- Managing Voice VLAN
- Defining GARP
- Managing IGMP Snooping
- Managing IGMP Snooping Querier
- Managing MLD Snooping
- Managing MLD Snooping Querier
- Managing Port-Channel
- Viewing Multicast Forwarding Database
- Managing Spanning Tree
- Defining 802.1p priority
- Managing Port Security
- Managing LLDP
- Managing LLDP-MED
- Managing VTP
- Managing Link State
- Managing Port-Backup
- Managing FIP-Snooping
- Routing Menu
- Security Menu
- IPv6 Menu
- Configuring IPv6 Global Configuration Page
- Configuring IPv6 Interface Configuration Page
- Viewing IPv6 Interface Summary Page
- Viewing IPv6 Interface Statistics Page
- Viewing IPv6 Neighbor Table Information Page
- Viewing IPv6 Static Neighbor Table Information Page
- Managing OSPFv3 Protocol
- Managing IPv6 Routes
- Managing RIPv6
- QOS Menu
- IPv4 Multicast Menu
- IPv6 Multicast Menu
- 232 -
Default Setting
None
Command Mode
Privileged Exec
Display Message
User Name: The name the user will use to login using the serial port, Telnet or Web. A new user may
be added to the switch by entering a name in a blank entry. The user name may
be up to eight characters, and is not case sensitive. Two users are included as the factory
default, admin, and guest.
User Access Mode: Shows whether the operator is able to change parameters on the switch
(Read/Write) or is only able to view them (Read Only). As a factory default, admin has Read/Write
access and guest has Read Only access. There can only be one Read/Write user and up to five Read
Only users.
SNMPv3 AccessMode: This field displays the SNMPv3 Access Mode. If the value is set to Read-
Write, the SNMPv3 user will be able to set and retrieve parameters on the system. If the value is set
to ReadOnly, the SNMPv3 user will only be able to retrieve parameter information. The SNMPv3
access mode may be different from the CLI and Web access mode.
SNMPv3 Authentication: This field displays the authentication protocol to be used for the specified
login user.
SNMPv3 Encryption: This field displays the encryption protocol to be used for the specified login
user.
7.7.1.2 show users account information
The user can go to the CLI Privilege Exec to get all of user information, use the show users accounts
Privilege command.
Syntax
show users accounts
Default Setting
None
Command Mode
Privileged Exec
Display Message
User Name: The local user account’s user name.
Access Mode: The user’s access level (read-only or read/write).
Lockout Status: Indicates whether the user account is locked out (true or false).
Password Expiration Date: The current password expiration date in date format.