Installation Manual

I
24 in or16 in.
(609mm/406 mm)
2-1 2-2 2-3 2-4
STEP 3 Attach TV Brackets to TV back STEP 4 Attach TV to the arm assembly
Made in China.
Position the wallplate template at your desired height
and line up the holes with your stud center line.
Level the wall plate and mark the holes.
Drill pilot holes using a 5/32 in (4mm) diameter drill bit.
of 3.5in.(90 mm).Be sure to drill into the center of the stud.
IMPORTANT: Pilot holes must be drilled to a depth
CAUTION:
property damage!
● Minimum solid concrete thickness: 8 in. (203 mm).
● Minimum concrete block size: 8 x 8 x 16 in. (203 x 203 x 406 mm)
● Minimum horizontal space between fasteners: 16 in
(406 mm
).
● Mount wall plate
directly onto the concrete surface.
Position wallplate template
at your
desired height. Level, then
mark the six hole locations.
Drill six pilot holes using a 3/8 in.
(10 mm) masonry drill bit.
Min.
8 in.
(203 mm)
Min. 8 in.
(203 mm)
Min. 16 in.
(406 mm)
CAUTION: Be sure the anchors are
seated flush with the concrete surface.
Install wall plate
DO NOT over-tighten the screws.
and screws
holding power of screws
with six washers
01
IMPORTANT : Ensure TV bracket is securely fastened before moving on to the next step.
CAUTION:Avoid potential personal injuries and property damage!
DO NOT use a power screwdriver for this step
STEP 2A Wall Plate Install( Wood Stud )
STEP 2B Wall Plate Install( Solid Concrete or Concrete Block )
½ x 3½ in. (38 x 89 mm)
Y
MUST BE
CAUTION: Avoid potential personal injuries
and property damage!
●
Drywall covering the wall must not exceed
5/8 in. (16 mm)
●
Minimum wood stud size: common 2 x 4 in.
(51 x 102 mm) nominal 1
CAUTION:
A
01 .
void potential personal injury
or property damage! All lag bolts
firmly tightened to prevent unwanted
movement of the wall plate
CAUTION:
Ensure the wall plate is securely
fastened to the wall before continuing on to the
next step.
the studs by finding the stud edges using an awl,
a thin nail, or an edge-to-edge stud finder.
Locate your studs. Verify and mark the center of
Install wall plate
washers
they are pulled firmly a gainst the wall plate
.Tighten the lag bolts only until
using lag bolt and
01
01
01
Y
X
Z
2
2
X
Y
3.5 in (90mm)
5/32 in.
( 4 mm)
Avoid potential personal injuries and
2A-1
2A-2 2A-3
01
Min. 16 in.
(406 mm)
drilled to a depth of 3.5 in ( 90 mm ).
Never drill into the mortar between blocks.
IMPORTANT:Pilot holes must be
Z
Insert six concrete anchors
( 10x80mm ) to the wall
CAUTION:
Improper use could reduce the
Y
a Flat Back
D E F
G J L
b Round Back/Extra Space
CAUTION: Avoid potential personal injury or property damage!
Make sure your locking screws
are tightened BEHIND the mounting plate
so the TV is securely fastened in place.
STEP 5 Tilt and level adjustment
2A-4
A B C
Wall plate
D E F H K M
Safety Bolt
Wall Plate
Wall Plate
Monitor Brackets
Monitor Brackets
Wall
Wall
Allen key
Levelling Mount(TV )
by hand dire ctly
knobs for tilt
angles adjustment
Wall Plate
Y
X
Wall Plate
24” 16"
(609mm/406mm)
Y
X