KIT#:503900K1 ITEM#:50301929ET02 IMPORTANT, RETAIN FOR FUTURE REFERENCE: READ CAREFULLY Hillcrest Concealed Motion Club Chair Customer Service E-Mail : customerservice@foremostgroups.com 8:30a.m.– 5:00p.m. EST, M-F Toll Free : 1-800-443-1410 (USA) Fax: (973) 428-8026 www.foremostgroups.
WARNING! • • Chairs have a 250 lbs weight capacity. Hang cushion over chair frame to dry if it gets wet to prevent mold/mildew. Please read instructions carefully and thoroughly before assembling. Check parts against the parts list to make sure you have all the parts needed for proper assembly. Familiarize yourself with the inventory of parts and the accompanying illustrations to ensure safe and proper assembly. Place the chair on a non-abrasive flat surface to prevent scratching.
PART DESCRIPTION PICTURE QTY G BOLT (5/16x 25 MM) 4 H BOLT (5/16x 45 MM) 4 I LOCK WASHER (Ø 8.5MM) 8 J FLAT WASHER (Ø 8.
1 Loosely attach U Support Bar to Right Arm Panel (C) & Left Arm Panel (D) with bolts (G) through lock washer (I) and flat washer (J) using wrench (N). Do not tighten the bolts at this point. Figure 1 C B D J I G 2 Loosely attach the Connector Bar (E) to Right Arm Panel (B) & Left Arm Panel (C) with countersunk bolts (F) using Hex Screw Driver (M). Do not tighten the bolts at this point.
3 Place the chair seat (A) on a non-abrasive flat surface. Align the holes on the support bar on the underside of the chair seat with the holes on the spring plates which are pre-attached to the chair base. Insert bolts (H) through the C-clamp alum plates (L), and support bar attached to the underside of the seat, and spring plates attached to the U support bar (D) as shown in the diagram. Secure bolts with flat washers (J), lock washers (I) and nuts (K).
4 Once all the nuts and bolts are in place, securely tighten all the bolts (F&G&H) and nuts (K), including the ones at the front part on the rocker mechanism with the hex screw driver (M) and the wrench (N) . Place the seat cushions (P) and back cushions (O) on the chairs. Your chair is ready for your enjoyment now.
CARE & MAINTENANCE Clean furniture frame with wet towel using mild soap and water solution. Dry completely with soft towel. Clean cushions and sling seat material with a mild solution of soap and water and hang cushions to drip dry completely. Store them in a clean dry area of your home. Do not machine wash or dry. Do not use bleach or strong solvents to clean any of your patio furniture. It will harm both fabrics and metal finishes.
WARRANTY EXCLUSIONS Failure caused by unreasonable or abusive use.
HILLCREST SQUARE GAS FIRE PIT KIT#: 503900K1 ITM./ART.#: 50310529E004 MODEL#: F170147 ANS Z21.97/CSA 2.41-2014 Outdoor Decorative Gas Appliances Installer: Leave these instructions with consumer. Consumer: Keep these instructions for further reference. DANGER WARNING If you smell gas: Shut off gas to the appliance. Extinguish any open flame. If odor continues, keep away from the appliance and immediately call your gas supplier or fire department. DANGER WARNING: For Outdoor Use Only.
IMPORTANT SAFETY INFORMATION 1. The installation must conform with local codes or, in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1●NFPA 54; National Fuel Gas Code; Natural Gas and Propane Installation Code, CSA B149.1; or Propane Storage and Handling Code, CSA B149.2, as applicable. 2.
IMPORTANT SAFETY INFORMATION ABOUT PROPANE (LP) GAS 1. The LP-gas supply cylinder to be used must be constructed and marked in accordance with the U.S. Deparment of Transportation (D.O.T.) Specifications for LP-Gas Cylinders, or the Standard for Cylinders, Spheres and Tubes for Transportation of Dangerous Goods and Commission, CAN/CSA-B339, as applicable. 2. The LP-gas supply cylinder to be used must have a listed overfilling prevention device (See Figure 1). 3.
PACKAGE CONTENTS A B L C I M J D H N G K E F PART DESCRIPTION QUANTITY PART DESCRIPTION QUANTITY A Lid 1 J B Table Top 1 K Door handle 1 C Back panel 1 L Weather cover 1 D Right panel 1 M Lava rock (13.
ILLUSTRATED PARTS LIST A Lid B Table Top C Back panel D Right panel E Base support F Decorative foot G Foot glider H Door panel I Left panel J Gas cylinder support K Door handle L Weather cover M Lava rock (13.
ASSEMBLY INSTRUCTIONS NOTE: Tool Required for Assembly: phillips screw driver ( NOT included) 1. Carefully unpack all parts from the box, compare parts with package content listed above, make sure all parts are present before beginning assembly of product. If any part is missing or damaged, do not attempt to assemble the product. Contact customer service for replacement parts. 2. Place table top (B) on a non-abrasive flat surface to prevent scratching.
F E D I Figure 4 5. Attach gas cylinder support (J) to base support (E) with bolt (AA) and washer (BB) using hex screw driver (CC), (see Figure 5). NOTE: Tighten ALL screws completely. Hardware Used: AA Bolt (M6 x 15) BB Washer (M6) CC Hex screw driver CC AA BB E x4 x4 x1 J Figure 5 6. With the help of another person, carefully turn the fire pit to the upright position.
7. Attach door handle (K) to door panel (H) with bolt (DD), then use Phillips screwdriver (not included) to screw tightly (see Figure 7). Hardware Used: DD Bolt (M4 x 25) x1 H K DD Figure 7 8. Put lava rock (M) around the burner, then remove the label from the pilot box (see Figure 8). A gas fire pit requires 13.2 lbs lava rock. NOTE: DO NOT completely cover the burner element or block the pilot box with the lava rocks.
10. Place the lid (A) onto the fire bowl when not in use to protect it from the elements or when fire pit is cooled COMPLETELY after use. Cover the fire pit with weather cover (L) when not in use to protect it from the elements or when fire pit is cooled COMPLETELY after use, (see Figure 10). NOTE: Allow 30 minutes after use for fire pit to cool down before placing the lid to prevent scalding.
STOP NATURAL GAS CONVERSION STOP Natural gas conversion must be performed only by natural gas provider or service company. 1. Disconnect the propane hose from the gas valve (see Figure 11). gas valve propane hose 2. Figure 11 Unscrew and disconnect the propane orifice from the bellows (see Figure 12). Propane orifice (2.21 mm diameter size) is painted with red mark. propane orifice propane orifice bellows bellows Figure 12 3.
4. Connect the natural gas hose with the gas valve by screwing clockwise tightly (see Figure 14). Plug the natural gas fixture into the natrual gas supply piping system (see Figure 15). gas valve natural gas fixture natural gas supply piping system natural gas hose Figure 14 5. Figure 15 Stick and cover the conversion label onto the propane rating plate (see Figure 16). Serial Number: CAUTION: This appliance has been converted to use natural gas. Propane orifice dia2.21mm, natural gas orifice dia4.
BATTERY Make sure the control knob is in the “OFF” position. Unscrew the push button cap on the ignitor module located on the control panel to access the battery compartment. The ignitor module requires one AAA size battery (See Figure 17), BATTERY IS NOT INCLUDED. WARNING: 1. Please observe proper polarity and use the correct battery type when placing or replacing the battery. Improper installation could result in ignition failure. 2.
gas valve-hose connection (Figure 20) inlet tube-bellows connection (Figure 21) To perform a leak test: 1. Make 2~3 oz. of leak solution by mixing one part liquid dishwashing detergent and three parts water. Noted: make sure control knob is “OFF”. 2. Apply several drops of solution where the cylinder attaches to regulator (see Figure 18), inspect the solution at the connection looking for bubbles. If NO bubbles appear, the connection is secure.
Observe Flame Height When Lit: The burner will display blue and yellow flames. These flames should be a blue / yellow color between 1~2 in. height (see Figure 23). These flames should not be yellow or produce thick smoke. This would indicate an obstruction of airflow through the burners. The flames should be blue with straight yellow tops.
REPLACEMENT PARTS LIST NO PART# DESCRIPTION 01 HLCST-SQTTA Table top 02 HLCST-RP Right panel 03 HLCST-LP Left panel 04 HLCST-DR Door panel 05 HLCST-BP Back panel 06 HLCST-FRLG Front-right leg 07 HLCST-BRLG Back-right leg 08 HLCST-FLLG Front-left leg 09 HLCST-BLLG Back-left leg 10 HLCST-UPBM Upper beam 11 HLCST-BTBM Bottom beam 12 HLCST-GCSPT Gas cylinder support 13 HLCST-FOOTGD Foot glider 14 HLCST-HDL Handle assembly 15 HLCST-THRMCPL Thermocouple 16 HLCST-PL
WARRANTY Firepits Burner, steel fire pit bowl, all mechanical parts and fittings to control panel and burner assembly are warranted for a period of one (1) year from original date of purchase, against defects in material and or workmanship. Rust is not covered. Frames Frames are warranted to be free from defects in materials and workmanship for a period of one (1) year. Damage to frames or welds due to improper assembly or exposure to water and sub-freezing temperatures, is not covered.
