Contents Before driving Introduction 2 Instrumentation 6 Controls and features 17 Seating and safety restraints 84 Starting and driving Starting 122 Driving 127 Roadside emergencies 144 Servicing Maintenance and care 162 Capacities and specifications 222 Customer assistance 230 Reporting safety defects 242 Index 243 All rights reserved.
Introduction The following warning may be required by California law: CALIFORNIA Proposition 65 Warning WARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
Introduction WARNINGS Warnings provide information which may reduce the risk of personal injury and prevent possible damage to others, your vehicle and its equipment. BREAKING-IN YOUR VEHICLE There are no particular guidelines for breaking-in your vehicle. During the first 1 600 km (1 000 miles) of driving, vary speeds frequently. This is recommended to give the moving parts a chance to break in. INFORMATION ABOUT THIS GUIDE The information found in this guide was in effect at the time of printing.
Introduction These are some of the symbols you may see on your vehicle.
Introduction Vehicle Symbol Glossary Child Safety Door Lock/Unlock Interior Luggage Compartment Release Symbol Panic Alarm Engine Oil Engine Coolant Engine Coolant Temperature Do Not Open When Hot Battery Avoid Smoking, Flames, or Sparks Battery Acid Explosive Gas Fan Warning Power Steering Fluid Maintain Correct Fluid Level Emission System Engine Air Filter Passenger Compartment Air Filter Jack MAX MIN Check fuel cap 5
Instrumentation Headlamp control (pg. 17) Instrument panel dimmer control (pg. 18) Instrument cluster (pg. 8) Trunk release — sedan only (pg. 66) Rear window wiper and washer — wagon only* (pg. 57) * if equipped 6 Parking brake release (pg. 129) Turn signal and wiper/washer control (pg. 56) Driver air bag (pg.
Instrumentation Electronic sound system (pg. 30) Speed control* (pg. 53) Climate control system (pg. 19) Gearshift (pg.
Instrumentation WARNING LIGHTS AND CHIMES F FUEL DOOR > H 60 E C 3 4 5 2 RPMx1000 100 6 1 20 180 MPH LOW COOLANT + 140 0 00000 20 – 60 0 0 0 0 80 40 km/h THEFT P R N D D 1 120 0 7 ABS ! P BRAKE CRUISE Turn signal Illuminates when the left or right turn signal or the hazard lights are turned on. If one or both of the indicators stay on continuously or flash faster, check for a burned-out turn signal bulb. Refer to Bulbs in the Maintenance and care chapter.
Instrumentation Safety belt Momentarily illuminates when the ignition is turned to the ON position to remind you to fasten your safety belts. For more information, refer to the Seating and safety restraints chapter. Door ajar Illuminates when the ignition is in the ON position and any door is open. It may also momentarily illuminate after the engine is started and all doors are closed. Check fuel cap Momentarily illuminates when the ignition is turned to the ON position to ensure your bulb is working.
Instrumentation Service engine soon Your vehicle is equipped with a computer that monitors the engine’s emission control system. This system is commonly known as the On Board Diagnostics System (OBD II). The OBD II system protects the environment by ensuring that your vehicle continues to meet government emission standards. The OBD II system also assists the service technician in properly servicing your vehicle.
Instrumentation Light is blinking: Engine misfire is occurring which could damage your catalytic converter. You should drive in a moderate fashion (avoid heavy acceleration and deceleration) and have your vehicle serviced at the first available opportunity. Under engine misfire conditions, excessive exhaust temperatures could damage the catalytic converter, the fuel system, interior floor coverings or other vehicle components, possibly causing a fire.
Instrumentation Anti-lock brake system (ABS) (If equipped) Momentarily illuminates when the ignition is turned to the ON position ABS to ensure the circuit is functional. If the light does not illuminate momentarily at start up, remains on or continues to flash, the ABS needs to be serviced. With the ABS light on, the anti-lock brake system is disabled and normal braking is still effective unless the brake warning light also remains illuminated with the parking brake released.
Instrumentation Engine oil pressure Momentarily illuminates when the ignition is turned to the ON position and the engine is off. Illuminates when the oil pressure falls below the normal range. Stop the vehicle as soon as safely possible and switch off the engine immediately. Check the oil level and add oil if needed. Refer to Engine oil in the Maintenance and care chapter. Charging system Illuminates when the ignition is turned to the ON position and the engine is off.
Instrumentation Key-in-ignition warning chime Sounds when the key is left in the ignition in the OFF/LOCK or ACC position and the driver’s door is opened. Headlamps on warning chime Sounds when the headlamps or parking lamps are on, the ignition is off (and the key is not in the ignition) and the driver’s door is opened.
Instrumentation Tachometer Indicates the engine speed in revolutions per minute. Driving with your tachometer pointer continuously at the top of the scale may damage the engine. 3 4 5 2 RPMx1000 1 0 6 7 Engine coolant temperature gauge Indicates the temperature of the engine coolant. At normal operating temperature, the needle remains H within the normal area (the area between the “H” and “C”). If it enters the red section, the engine is C overheating.
Instrumentation Odometer Registers the total kilometers (miles) of the vehicle. 60 0 0 0 0 80 40 100 60 140 100 0 00000 20 20 180 MPH P Trip odometer Registers the kilometers (miles) of individual journeys. To reset, depress the control. km/h 120 R N D D 1 60 0 0 0 0 80 40 60 140 100 0 00000 20 20 180 MPH P km/h 120 R N D D1 Fuel gauge Displays approximately how much fuel is in the fuel tank (when the key is in the ON position).
Controls and features HEADLAMP CONTROL Rotate the headlamp control to the first position to turn on the parking lamps. Rotate to the second position to also turn on the headlamps. A Daytime running lamps (DRL) (if equipped) Turns the headlamps on with a reduced output. To activate: • the ignition must be in the ON position and • the headlamp control is in the OFF or Parking lamps position. Always remember to turn on your headlamps at dusk or during inclement weather.
Controls and features PANEL DIMMER CONTROL Use to adjust the brightness of the instrument panel during headlamp and parklamp operation. • Rotate up to brighten. • Rotate down to dim. • Rotate to full up position (past detent) to turn on interior lamps. • Rotate to full down position (past detent) to turn off interior lamps. The dome lamp will not illuminate if the control switch is in the OFF position.
Controls and features The defroster turns off automatically after 10 minutes or when the ignition is turned to the OFF position. To manually turn off the defroster before 10 minutes have passed, push the control again. Activating the rear window defroster will also activate the heated mirrors (if equipped). For more information refer to Heated outside mirrors in this chapter.
Controls and features Mode selector control Controls the direction of the airflow to the inside of the vehicle. A/C The air conditioning compressor can operate in all modes except . However, the air conditioning will only function if the outside temperature is about 6°C (43°F) or higher.
Controls and features • (Floor and defrost)-Distributes outside air through the windshield defroster ducts and the floor ducts. Heating and air conditioning capabilities are provided in this mode. For added customer comfort, when the temperature control knob is anywhere in between the full hot and full cold positions, the air distributed through the floor ducts will be slightly warmer than the air sent to the windshield defrost ducts.
Controls and features • Don’t put objects under the front seat that will interfere with the airflow to the back seats. • Remove any snow, ice or leaves from the air intake area at the base of the windshield. • Do not place objects over the defroster outlets. These objects can block airflow and reduce your ability to see through your windshield. Avoid placing small objects on top of the instrument panel.
Controls and features Turning the EATC on OUTSIDE TEMP OFF MAX F R A/C AUTO TEMP Press AUTO, any of the override controls or the fan speed control. The EATC will only operate when the vehicle is running. Turning the EATC off Press OFF. The Outside Temperature function will continue to operate until the ignition is turned off. OUTSIDE TEMP OFF MAX A/C AUTO TEMP Automatic operation Press AUTO and select the desired temperature.
Controls and features Temperature selection The display window indicates the selected temperature, function (AUTO or one of the override controls) and manual control of fan speed ( ) if automatic fan speed is not desired. AUTO F FAN • • • To control the temperature, select any temperature between 18°C (65°F) and 29°C (85°F) by pressing the temperature control.
Controls and features Temperature conversion OUTSIDE TEMP OFF MAX F R A/C AUTO TEMP Press MAX A/C and F at the same time (until the display changes) to switch between Fahrenheit and Celsius. Fan speed ( ) When AUTO is pressed, fan speed is adjusted automatically for existing conditions. You can override fan speed at any time. To control fan speed manually, press the fan control to cancel automatic fan speed operation. Press the control up for higher fan speed or down for lower fan speed.
Controls and features Manual override controls OUTSIDE TEMP OFF MAX F R A/C AUTO TEMP The override controls are located at the bottom of the EATC and allow you to determine where airflow is directed. To return to full automatic control, press AUTO. The air conditioning compressor can operate in all modes except and . It will also operate only when required when AUTO has been selected. However, the air conditioning will only function if the outside temperature is about 6°C (43°F) or higher.
Controls and features • • • • • (Floor)-Allows for maximum heating by distributing outside air through the floor ducts. However, the air cannot be cooled below the outside temperature because the air conditioning does not operate in this mode. (Panel and floor) -Distributes outside air through the instrument panel registers and the floor ducts. Heating and air conditioning capabilities are provided in this mode. The air will be heated or cooled based on the temperature selection.
Controls and features Operating tips • In humid weather conditions, place the climate control system in F before driving. This will reduce fogging on your windshield. Once the windshield has been cleared, operate the climate control system as desired. • To reduce humidity buildup inside the vehicle in cold weather conditions, don’t drive with the climate control system in the OFF or MAX A/C position.
Controls and features • Do not place objects over the defroster outlets. These objects can block airflow and reduce your ability to see through your windshield. Avoid placing small objects on top of the instrument panel. These objects may fall down into the defroster outlets and block airflow, in addition to damaging the climate control system. Do not place objects on top of the instrument panel, as these objects may become projectiles in a collision or sudden stop.
Controls and features USING YOUR AUDIO SYSTEM AM/FM Stereo Volume/power control Press the control to turn the audio system on or off. Turn control to raise or lower volume.
Controls and features If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on. If you wish to maintain your preset volume level, turn the audio system off with the power control before switching off the ignition. AM/FM select The AM/FM select control works in radio mode. Press the AM or FM control to enter radio mode.
Controls and features Seek function in radio mode • Press to find the next listenable station down the frequency band. to find the next listenable station up the frequency band. • Press Scan function The scan function works in radio mode. Scan function in radio mode Press the SCAN control to hear a brief sampling of all listenable stations on the frequency band. Press the control again to stop the scan mode. Radio station memory preset The radio is equipped with six station memory preset controls.
Controls and features • The treble adjust control allows you to increase or decrease the audio system’s treble output. Speaker balance/fade adjust • Speaker sound distribution can be adjusted between the right and left speakers. • Speaker sound can be adjusted between the front and rear speakers. Setting the clock To set the hour, press and hold the hour (H) control. When the desired hour appears, release the control. To set the minute, press and hold the minute (M) control.
Controls and features MACHT Audio System with AM/FM Stereo/Cassette Volume/power control Press the control to turn the audio system on or off. Turn control to raise or lower volume. If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on. If you wish to maintain your preset volume level, turn the audio system off with the power control before switching off the ignition.
Controls and features AM/FM select The AM/FM select control works in radio, tape and CD modes (if equipped). Press the AM or FM control to enter into radio mode. AM/FM select in radio mode This control allows you to select AM or FM frequency bands. Press the control to switch between AM, FM1 or FM2 memory preset stations. Pressing the AM or FM controls when the ignition is turned on will also engage the radio. AM/FM select in tape mode Press this control to stop tape play and begin radio play.
Controls and features • Press to select the next disc in the CD changer. Hold the control to fast-forward through the remaining discs. Seek function The seek function control works in radio, tape or CD mode. Seek function in radio mode • Press to find the next listenable station down the frequency band. to find the next listenable station up the frequency band. • Press Seek function in tape mode • Press to listen to the previous selection on the tape. to listen to the next selection on the tape.
Controls and features Scan function in CD mode Press the SCAN control to hear a short sampling of all selections on the CD. (The CD scans in a forward direction, wrapping back to the first track at the end of the CD.) To stop on a particular selection, press the control again. Radio station memory preset The radio is equipped with six station memory preset controls. These controls can be used to select up to six preset AM stations and twelve FM stations (six in FM1 and six in FM2).
Controls and features • Speaker sound can be adjusted between the front and rear speakers. Inserting a tape Push only slightly when inserting a cassette tape (with the open edge to the right). A cassette deck loading mechanism pulls the tape in the rest of the way. You can switch from CD to tape play by inserting a tape into the cassette deck. Tape/CD select • Pressing the TAPE or CD control when the ignition is on will engage the system if a tape or CD is present in the audio system.
Controls and features Fast forward The fast forward control works in tape and CD modes. • In the tape mode, tape direction will automatically reverse when the end of the tape is reached. • In CD mode, pressing the control for less than three seconds results in slow forward action. Pressing the control for more than three seconds results in fast forward action. • You can cancel the fast forward mode by pressing TAPE, or the FF control.
Controls and features Shuffle feature The shuffle feature operates in CD mode and plays all tracks on the current disc in random order. If equipped with the CD changer, the shuffle feature continues to the next disc after all tracks are played. Press the SHUFFLE control to start this feature. Random order play will continue until the SHUFFLE control is pressed again. Setting the clock To set the hour, press and hold the hour (H) control. When the desired hour appears, release the control.
Controls and features Audio System with AM/FM Stereo/Single CD Player Volume/power control Press the control to turn the audio system on or off. Turn control to raise or lower volume. If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on. If you wish to maintain your preset volume level, turn the audio system off with the power control before switching off the ignition.
Controls and features AM/FM select The AM/FM select control works in radio, and CD modes (if equipped). Press the AM or FM control to enter into radio mode. AM/FM select in radio mode This control allows you to select AM or FM frequency bands. Press the control to switch between AM, FM1 or FM2 memory preset stations. Pressing the AM or FM controls when the ignition is turned on will also engage the radio. AM/FM select in CD mode Press this control to stop CD play and begin radio play.
Controls and features Seek function The seek function control works in radio or CD mode. Seek function in radio mode • Press to find the next listenable station down the frequency band. to find the next listenable station up the frequency band. • Press Seek function in CD mode • Press to seek to the previous track of the current disc. If a selection has been playing for three seconds or more and you press , the CD changer will replay that selection from the beginning.
Controls and features Setting memory preset stations 1. Select the frequency band with the AM/FM select control. 2. Select a station. Refer to Tune adjust or Seek function for more information on selecting a station. 3. Press and hold a memory preset control until the sound returns, indicating the station is held in memory on the control you selected. Bass/treble adjust • The bass adjust control allows you to increase or decrease the audio system’s bass output.
Controls and features CD select • Pressing the CD control when the ignition is on will engage the system if a CD is present in the audio system. • To begin CD play, press the CD control. The first track of the first disc will begin playing. After that CD play will begin where it stopped last. • Press the CD control again to toggle between single CD mode and CD changer mode (if available).
Controls and features Compression adjust Compression adjust brings soft and loud CD passages together for a more consistent listening level. Press the COMP control to activate and deactivate compression adjust. Shuffle feature The shuffle feature operates in CD mode and plays all tracks on the current disc in random order. If equipped with the CD changer, the shuffle feature continues to the next disc after all tracks are played. Press the SHUFFLE control to start this feature.
Controls and features CD changer (if equipped) Your CD changer is either located in the trunk, the console or the right side cargo area storage compartment. 1. Slide the door to access the CD changer magazine. 2. Press to eject the magazine. 3. Turn the magazine (A) over. 4. Using the disc holder release knob (C), pull the disc holder (B) out of the magazine.
Controls and features A If you pull too hard on the disc holder, the disc holder may come completely out of the magazine. If this happens, reinsert the disc holder back into the magazine while pressing on the lever (A). 5. Line up the CD with the groove of the disc holder. Ensure that the label on the CD faces downwards. 6. Press in on the disc holder until it locks securely into the magazine. If the disc holders are not fully locked into the magazine, the unit will not operate.
Controls and features The CD magazine may be inserted or ejected with the radio power off. ONLY use the magazine supplied with the CD changer, other types will damage the unit. Keep the CD changer door closed. Coins and foreign objects will damage the CD player and void your audio system warranty. Do not insert any promotional (odd shaped or sized) discs, or discs with removable labels into the CD player as jamming may occur.
Controls and features • Do not insert more than one disc into each slot of the CD changer magazine. Do not insert any promotional (odd shaped or sized) discs, or discs with removable labels into the CD player as jamming may occur. Cleaning cassette player (if equipped) Clean the tape player head with a cassette cleaning cartridge after 10 to 12 hours of play in order to maintain the best sound and operation. Cassette and cassette player care • Use only cassettes that are 90 minutes long or less.
Controls and features • Terrain.Hills, mountains and tall buildings between your vehicle’s antenna and the radio station signal can cause FM reception problems. Static can be caused on AM stations by power lines, electric fences, traffic lights and thunderstorms. Moving away from an interfering structure (out of its “shadow”) returns your reception to normal. • Station overload.Weak signals are sometimes captured by stronger signals when you pass a broadcast tower.
Controls and features TRACTION CONTROLY (IF EQUIPPED) This control can be used to turn the Traction Controly on or off. Refer to the Traction Controlysection of the Driving chapter for more information. O F T/C F POSITIONS OF THE IGNITION 1. ACCESSORY, allows the electrical 3 accessories such as the radio to 2 operate while the engine is not running. 2. LOCK, locks the steering wheel, automatic transmission gearshift 4 1 lever and allows key removal. 5 3.
Controls and features SPEED CONTROL (IF EQUIPPED) To turn speed control on • Press ON. Vehicle speed cannot be controlled until the vehicle is traveling at or above 48 km/h (30 mph). Do not shift the gearshift lever into N (Neutral) with the speed control on. OFF ON Do not use the speed control in heavy traffic or on roads that are winding, slippery, or unpaved. To turn speed control off • Press OFF or • Turn off the vehicle ignition.
Controls and features To set a speed • Press SET+. For speed control to operate, the speed control must be ON and the vehicle speed must be greater than 48 km/h (30 mph). If you drive up or down a steep hill, your vehicle speed may vary momentarily slower or faster than the set speed. This is normal. Speed control cannot reduce the vehicle speed if it increases above the set speed on a downhill.
Controls and features To set a lower set speed • Press and hold CST −. Release the control when the desired speed is reached or • Press and release CST − to operate the Tap-Down function. Each press will decrease the set speed by 1.6 km/h (1 mph) or • Depress the brake pedal. When the desired vehicle speed is reached, press SET +. To disengage speed control • Depress the brake pedal. Disengaging the speed control will not erase the previously programmed set speed.
Controls and features Indicator light This light comes on when either the CRUISE SET or RES controls are pressed. It turns off when the speed control OFF control is pressed, the brake is applied or the ignition is turned to the OFF position. TURN SIGNAL CONTROL • Push down to activate the left turn signal. • Push up to activate the right turn signal. WINDSHIELD WIPER/WASHER CONTROLS Rotate the windshield wiper control to the desired interval, low or high speed position.
Controls and features Rear window wiper and washer (wagon only) The rear wiper control is located under the headlamp controls Press the wiper control to activate the rear wiper. Press again to turn off the wiper. Press the washer control to activate the rear washer. The wiper will come on when the washer control is pressed, if it is not already on. HAZARD FLASHER For information on the hazard flasher control, refer to Hazard flasher in the Roadside emergencies chapter.
Controls and features TILT STEERING Pull the tilt steering control toward you to move the steering wheel up or down. Hold the control while adjusting the wheel to the desired position, then release the control. Never adjust the steering wheel when the vehicle is moving. REPLACING THE INTERIOR BULBS Check the operation of the following interior bulbs frequently: • interior overhead lamp • map lamp For bulb replacement, see a dealer or qualified technician.
Controls and features With the control in the middle position, the dome lamp will illuminate whenever a front door is opened. If either front door has been opened from the outside, the lamp will remain on for 25 seconds after the door is shut. If any other door has been opened from the inside, the lamp will shut off immediately after the door is closed. The map lamp controls (if equipped) are located on the dome lamp. Press the controls on either side of each lens on each map lamp to activate the lamps.
Controls and features ILLUMINATED VISOR MIRROR (IF EQUIPPED) To turn on the visor mirror lamps, lift the mirror cover. Adjust the amount of light by sliding the control. MOON ROOF (IF EQUIPPED) Push up on the control to raise the moon roof to the vent position. Push the front portion of the control rearward to open the moon roof. To close, press and hold the front portion of the control.
Controls and features You will need a Phone Adapter System (PAS) that is compatible with your cell phone that you install into the center console. This system includes a Phone Adapter Module (PAM) with a Wiring Harness and a Hang-Up Cup. For more information, call 1–800–736–9450 to order the Phone Adapter System (PAS) for your specific phone. To install the PAS, locate the four screw holes in the console. Install the PAM and the hang-up cup with four screws.
Controls and features To prevent damage to the antenna or your car, remove the cellular phone antenna mast before using an automatic car wash. POWER WINDOWS Press and hold the rocker switches to open and close windows. • Press the top portion of the rocker switch to close. AUTO • Press the bottom portion of the rocker switch to open. AUTO One touch down • Press AUTO completely down to the second detent. The driver’s window will open fully. Depress up to stop window operation.
Controls and features Window lock The window lock feature allows only the driver to operate the power windows. To lock out all the window controls except for the driver’s press the left side of the control. Press the right side to restore the window controls. Accessory delay (if equipped) With accessory delay, the window switches may be used for up to ten minutes after the ignition switch is turned to the OFF position or until any door is opened.
Controls and features POWER SIDE VIEW MIRRORS To adjust your mirrors: to adjust the left 1. Select mirror or to adjust the right mirror. 2. Move the control in the direction you wish to tilt the mirror. 3. Return to the center position to disable adjust function. Heated outside mirrors (if equipped) Both mirrors are heated automatically to remove ice, mist and fog when the rear window defrost is activated.
Controls and features CENTER CONSOLE Your vehicle may be equipped with a variety of console features. These include: • Utility compartment • Bin mat (snap-in) • Cupholders (front and rear) • Coin holder slots • Compact disc changer (if equipped) • Tissue holder • Rear A/C vent • Rear ashtray (see your Ford, Lincoln Mercury dealer to obtain rear ashtray Use only soft cups in the cupholder. Hard objects can injure you in a collision.
Controls and features TRUNK REMOTE CONTROL Press the remote trunk release control on the instrument panel to the left of the steering wheel. LIFTGATE (WAGON ONLY) You can open and close the liftgate and the liftgate window from outside the vehicle. It cannot be opened from inside the cargo area. • To open the liftgate window, unlock the liftgate (with the key, the power door locks or the remote entry key fob) and push the key lock cylinder.
Controls and features CARGO AREA FEATURES Storage compartment Your vehicle comes equipped with a storage compartment in the floor of the cargo area. An additional compartment is in the rear trim panel on the right. Always put the load you are carrying as far forward as possible. Cargo net (if equipped) (Wagon) The cargo net secures lightweight objects in the cargo area. Attach the net to the anchors provided. Do not put more than 22 kg (50 lbs.) in the net.
Controls and features To install the shade: 1. Fasten the cover into the mounting brackets (make sure the cover is right side up). 2. Pull the end of the shade toward you and hook the sides into the notches (right side first) in the rear trim panels. To reduce the risk of injuries, the fasteners for cargo area cover must be properly attached to the mounting clips on the rear trim panels. Do not place any objects on the cargo area cover.
Controls and features 2. Wrap the vinyl around the roller tube twice. Tuck the edges of the vinyl inside the end cap with each wrap. 3. Fold the edges of the vinyl towards the center, making sure that the edges clear the end cap slots. Use tape or a rubber band to hold the vinyl to the left side of the tube. 4. Push in the right end cap (marked RH) about 1⁄4 of the total length to disengage the clutch and hold the end cap in while turning the roller tube toward you 14 times. 5. Let go of the right end cap.
Controls and features Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. The remote entry system allows you to lock or unlock all vehicle doors, trunk and liftgate without a key. The remote entry features only operate with the vehicle in P (Park) or N (Neutral) and the ignition in the, ACC, OFF or ON positions.
Controls and features Unlocking the liftgate/trunk Press the control to unlock the liftgate/trunk. Sounding a panic alarm Press this control to activate the alarm. To deactivate the alarm, press the control again or turn the ignition to ACC or ON. Panic alarm will only operate with the ignition in the OFF position. Illuminated entry The interior lamps illuminate when the remote entry system is used to unlock the door(s).
Controls and features Replacing lost transmitters If a remote transmitter has been lost and you would like to remove it from the vehicle’s memory, or you would like to purchase additional remote transmitters and have them programmed to your vehicle: • Take all your vehicle’s transmitters to your dealer for programming, or • Perform the programming procedure yourself Programming remote transmitters It is necessary to have all (maximum of four — original and/or new) of your remote transmitters available prio
Controls and features Replacing the battery The remote transmitter is powered by one coin type three-volt lithium battery CR2032 or equivalent. Typical operating range will allow you to be up to 10 meters (33 feet) away from your vehicle. A decrease in operating range can be caused by: • weather conditions • nearby radio towers • structures around the vehicle • other vehicles parked next to the vehicle To replace the battery: 1. Twist a thin coin between the two halves of the transmitter near the key ring.
Controls and features The system is ready to arm whenever the key is removed from the ignition. Any of the following actions will prearm the alarm system: • Press the remote entry lock control (doors opened or closed). • Press 7/8 and 9/0 controls on the keyless entry pad at the same time to lock the doors (doors opened or closed). 1 2 3 4 5 6 7 8 9 0 • Open a door and press the power door lock control to lock the doors.
Controls and features If the doors/hood or liftgate (wagon) are not closed and you press the remote entry transmitter twice to confirm the doors are locked, the horn will chirp twice to warn you that a door/hood or liftgate (wagon) is still open. Disarming the system You can disarm the system by any of the following actions: • Unlock the doors by using your remote entry transmitter. • Unlock the doors by using your keyless entry pad. 1 2 3 4 5 6 7 8 9 0 • Unlock the doors or liftgate with a key.
Controls and features Triggering the anti-theft system The armed system will be triggered if: • Any door, liftgate or hood is opened without using the door key or the remote entry transmitter. • The trunk is forced opened.
Controls and features 2. Press the 1/2 control within five seconds of step 1. 1 2 3 4 5 6 7 8 9 0 3. Enter your personal 5 digit code. Enter each digit within five seconds of the previous one. Do not set a code that includes three of the same number or presents them in sequential order. Thieves can easily figure out these types of codes. Your personal code does not replace the permanent code that the dealership gave you. You can use either code to unlock your vehicle.
Controls and features 2. To unlock the passenger’s door(s) and liftgate (wagon), press the 3/4 control within five seconds of unlocking the driver’s door. 3. To unlock the trunk or liftgate (wagon), enter the five-digit factory-set code, then press the 5/6 control within five seconds. Locking the doors and liftgate (wagon), press the 7/8 and 9/0 controls at the same time. This can be done at any time.
Controls and features The user should receive a horn chirp to indicate the system has been altered. Pressing the power door UNLOCK control button again will toggle the Autolock/Relock states. • Turn ignition to OFF to exit. Deactivating/activating horn chirp There are 2 methods to enable/disable this feature. One through your dealer and the second with a door lock sequence using the following instructions: 1. Turn the ignition key to RUN, then press the door UNLOCK control button 3 times. 2.
Controls and features Automatic arming The vehicle is armed immediately after switching the ignition to the 3 (OFF) position. The THEFT light in the instrument cluster will flash every two seconds when the vehicle is armed. 2 3 4 1 5 Automatic disarming Switching the ignition to the 4 (ON) position with a coded key disarms the vehicle. The THEFT light will illuminate for three seconds and then go out.
Controls and features Large metallic objects, electronic devices on the key chain that can be used to purchase gasoline or similar items, or a second key on the same key ring as the coded key may cause vehicle starting issues. If present, you need to keep these objects from touching the coded key while starting the engine. These objects and devices cannot damage the coded key, but can cause a NO—START condition if they are too close to the key during engine start.
Controls and features Programming spare keys A maximum of eight keys can be coded to your vehicle. Only SecuriLocky keys can be used. To program a coded key yourself, you will need two previously programmed coded keys (keys that already operate your vehicle’s engine) and the new unprogrammed key(s) readily accessible for timely implementation of each step in the procedure.
Controls and features INTERIOR LUGGAGE COMPARTMENT RELEASE Your vehicle is equipped with a mechanical interior luggage compartment release handle that provides a means of escape for children and adults in the event they become locked inside the luggage compartment. Adults are advised to familiarize themselves with the operation and location of the release handle. To open the luggage compartment door (lid) from the inside, pull the illuminated “T” shaped handle and push up on the trunk lid.
Seating and safety restraints SEATING Adjustable head restraints Your vehicle’s seats are equipped with head restraints which are vertically adjustable. The purpose of these head restraints is to help limit head motion in the event of a rear collision. To properly adjust your head restraints, lift the head restraint so that it is located directly behind your head or as close to that position as possible. Refer to the following to raise and lower the head restraints.
Seating and safety restraints Adjusting the front manual seat Never adjust the driver’s seat or seatback when the vehicle is moving. Do not pile cargo higher than the seatbacks to reduce the risk of injuring people in a collision or sudden stop. Always drive and ride with your seatback upright and the lap belt snug and low across the hips. Reclining the seatback can reduce the effectiveness of the seat’s safety belt in the event of a collision. Lift handle to move seat forward or backward.
Seating and safety restraints Adjusting the front power seat (if equipped) Never adjust the driver’s seat or seatback when the vehicle is moving. Do not pile cargo higher than the seatbacks to avoid injuring people in a collision or sudden stop. Always drive and ride with your seatback upright and the lap belt snug and low across the hips. Reclining the seatback can reduce the effectiveness of the seat’s safety belt in the event of a collision.
Seating and safety restraints Using the manual lumbar support (if equipped) The lumbar control is located on the front of the seat cushion. Turn to adjust lumbar support. REAR SEATS 2nd seat/split-folding rear seat (if equipped) One or both rear seatbacks can be folded down to provide additional cargo space. To lower the seatback(s) from inside the vehicle, pull tab to release seat back and then fold seatback down. When raising the seatback(s), make sure you hear the seat latch into place.
Seating and safety restraints 3rd seat (wagon only) The third seat faces the rear of the vehicle. For height and weight limits, see the label on the seat cushion. When the seat is down, the back of your wagon has a flat surface for carrying cargo. To open up the seat: 1. Unlock the floor panel with the key, then use the handle to fold the floor panel toward the front of the car. 2. Remove the cargo cover. The cargo cover must be removed or the seatback will not latch in the upright position. 3.
Seating and safety restraints SAFETY RESTRAINTS Personal Safety System The Personal Safety System provides an improved overall level of frontal crash protection to front seat occupants and is designed to help further reduce the risk of air bag-related injuries. The system is able to analyze different occupant conditions and crash severity before activating the appropriate safety devices to help better protect a range of occupants in a variety of frontal crash situations.
Seating and safety restraints common, moderate-severity impacts. A higher energy level is provided for the most severe impacts. Whether or not the air bag deploys at all can also be different for the driver versus the passenger based upon driver’s seat position and safety belt usage allowing further tailoring of the system.
Seating and safety restraints When are the front air bags and pretensioners deployed? Front air bags and pretensioners are designed to activate in frontal and near-frontal collisions, not rollover, side-impacts, or rear-impacts unless the collision causes sufficient longitudinal deceleration. The fact that the pretensioners or air bags did not activate in a collision does not mean that something is wrong with the system.
Seating and safety restraints In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt. Each seating position in your vehicle has a specific safety belt assembly which is made up of one buckle and one tongue that are designed to be used as a pair. 1) Use the shoulder belt on the outside shoulder only. Never wear the shoulder belt under the arm. 2) Never swing the safety belt around your neck over the inside shoulder.
Seating and safety restraints The front and rear outboard safety restraints in the vehicle are combination lap and shoulder belts. The front passenger and rear seat outboard safety belts have two types of locking modes described below: Energy management retractors Your vehicle has a seat belt system equipped with energy management retractors at the driver and front outboard passenger seating positions. An energy management retractor is a device which pays out webbing in a controlled manner.
Seating and safety restraints Vehicle sensitive mode The vehicle sensitive mode is the normal retractor mode, allowing free shoulder belt length adjustment to your movements and locking in response to vehicle movement. For example, if the driver brakes suddenly or turns a corner sharply, or the vehicle receives an impact of approximately 8 km/h (5 mph) or more, the combination safety belts will lock to help reduce forward movement of the driver and passengers.
Seating and safety restraints • Grasp the shoulder portion and pull downward until the entire belt is extracted. • Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the automatic locking mode. How to disengage the automatic locking mode Disconnect the combination lap/shoulder belt and allow it to retract completely to disengage the automatic locking mode and activate the vehicle sensitive (emergency) locking mode.
Seating and safety restraints Safety belt pretensioner Your vehicle is equipped with safety belt pretensioners at the driver and front outboard passenger seating positions. The safety belt pretensioners are designed to activate only when the safety belts are fastened during certain frontal or near-frontal collisions with sufficient longitudinal deceleration.
Seating and safety restraints Front safety belt height adjustment Your vehicle has safety belt height adjustments for the driver and front passenger. Adjust the height of the shoulder belt so the belt rests across the middle of your shoulder. To lower the shoulder belt height, pull the control down and slide the height adjuster down. To raise the height of the shoulder belt, slide the height adjuster up. Pull down on the height adjuster to make sure it is locked in place.
Seating and safety restraints Insert the tongue into the correct buckle (the buckle closest to the direction the tongue is coming from). To lengthen the belt, turn the tongue at a right angle to the belt and pull across your lap until it reaches the buckle. To tighten the belt, pull the loose end of the belt through the tongue until it fits snugly across the hips. Shorten and fasten the belt when not in use.
Seating and safety restraints To fasten the belt, pull the combination lap and shoulder belt from the retractor so that the shoulder belt portion of the safety belt crosses your shoulder and chest. Be sure the belt is not twisted. If the belt is twisted, remove the twist. Insert the tongue into the proper buckle for your seating position until you hear a snap and feel it latch. Make sure the tongue is securely fastened to the buckle by pulling on the tongue.
Seating and safety restraints the label. Also, use the safety belt extension only if the safety belt is too short for you when fully extended. Do not use extensions to change the fit of the shoulder belt across the torso. Safety belt warning light and indicator chime The seat belt warning light illuminates in the instrument cluster and a chime sounds to remind the occupants to fasten their safety belts. Conditions of operation If...
Seating and safety restraints If... The driver’s safety belt is not buckled before the vehicle has reached at least 5 km/h (3 mph) and 1-2 minutes have elapsed since the ignition switch has been turned to ON... Then... The Belt Minder feature is activated - the safety belt warning light illuminates and the warning chime sounds for 6 seconds every 30 seconds, repeating for approximately 5 minutes or until safety belt is buckled.
Seating and safety restraints Reasons given... “Traffic is light” Consider... Nearly 1 of 2 deaths occur in single-vehicle crashes, many when no other vehicles are around. “Belts wrinkle my Possibly, but a serious crash can do much more clothes” than wrinkle your clothes, particularly if you are unbelted. Set the example, teen deaths occur 4 times more “The people I’m with don’t wear often in vehicles with TWO or MORE people. belts” Children and younger brothers/sisters imitate behavior they see.
Seating and safety restraints • • • • the ignition switch is in the OFF position all vehicle doors are closed the driver’s safety belt is unbuckled the parklamps/headlamps are in OFF position (If vehicle is equipped with Autolamps, this will not affect the procedure.) To reduce the risk of injury, do not deactivate/activate the Belt Minder feature while driving the vehicle. 1. Turn the ignition switch to the RUN (or ON) position. (DO NOT START THE ENGINE) 2.
Seating and safety restraints Safety belt maintenance Inspect the safety belt systems periodically to make sure they work properly and are not damaged. Inspect the safety belts to make sure there are no nicks, tears or cuts. Replace if necessary.
Seating and safety restraints severity. This information will assist Ford in the servicing of your vehicle and may help Ford better understand real world collisions and further improve the safety of future vehicles. The air bag supplemental restraint system is designed to work in conjunction with the safety belts to help protect the driver and front outboard passenger from certain upper body injuries. The term “supplemental restraint” means the air bags are intended as a supplement to the safety belts.
Seating and safety restraints Important supplemental restraint system precautions Air bags DO NOT inflate slowly or gently and the risk of injury from a deploying air bag is greatest close to the trim covering the air bag module. All occupants of the vehicle, including the driver, should always properly wear their safety belts, even when an air bag SRS is provided. Always transport children 12 years old and under in the back seat and always properly use appropriate child restraints.
Seating and safety restraints Do not put anything on or over the air bag module. Placing objects on or over the air bag inflation area may cause those objects to be propelled by the air bag into your face and torso causing serious injury. Do not attempt to service, repair, or modify the Air Bag Supplemental Restraint System or its fuses. See your Ford or Lincoln Mercury dealer.
Seating and safety restraints Determining if the system is operational The supplemental restraint system uses a warning indicator in the instrument cluster or a back-up tone to indicate the condition of the system. Refer to the Warning Light section in the Instrument cluster chapter. Routine maintenance of the air bag is not required. A difficulty with the system is indicated by one or more of the following: • The readiness light (same light for front and side air bag system) will either flash or stay lit.
Seating and safety restraints How do the air bag supplemental restraints work? The air bags inflate and deflate rapidly upon activation. After air bag deployment, it is normal to notice a smoke-like, powdery residue or smell the burnt propellant. This may consist of cornstarch, talcum powder (to lubricate the bag) or sodium compounds (e.g., baking soda) that result from the combustion process that inflates the air bag.
Seating and safety restraints Side air bag system (if equipped) Do not place objects or mount equipment on or near the air bag cover on the side of the seatbacks of the front seats or in front seat areas that may come into contact with a deploying air bag. Failure to follow these instructions may increase the risk of personal injury in the event of a collision. Do not use accessory seat covers.
Seating and safety restraints How does the side air bag system work? The side air bag system consists of the following: • An inflatable nylon bag (air bag) with a gas generator concealed behind the outboard bolster of the driver and front passenger seatbacks. • A special seat cover designed to allow airbag deployment. • The same warning light, electronic control and diagnostic unit as used for the front air bags. • Two crash sensors located under the outboard side of the front seats, attached to the floor.
Seating and safety restraints Several air bag system components get hot after inflation. Do not touch them after inflation. If the side air bag has deployed, the air bag will not function again. The side air bag system (including the seat) must be inspected and serviced by a qualified technician in accordance with the vehicle service manual. If the air bag is not replaced, the unrepaired area will increase the risk of injury in a collision.
Seating and safety restraints Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from injury in a collision. Always follow the instructions and warnings that come with any infant or child restraint you might use. When possible, always place children under age 12 in the rear seat of your vehicle. Accident statistics suggest that children are safer when properly restrained in the rear seating positions than in the front seating position.
Seating and safety restraints SAFETY SEATS FOR CHILDREN Child and infant or child safety seats Use a safety seat that is recommended for the size and weight of the child. Carefully follow all of the manufacturer’s instructions with the safety seat you put in your vehicle. If you do not install and use the safety seat properly, the child may be injured in a sudden stop or collision.
Seating and safety restraints • Put the safety belt in the automatic locking mode. Refer to Automatic locking mode. Ford recommends the use of a child safety seat having a top tether strap. Install the child safety seat in a seating position which is capable of providing a tether anchorage. For more information on top tether straps, refer to Attaching safety seats with tether straps in this chapter.
Seating and safety restraints 2. Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together. 3. While holding the shoulder and lap belt portions together, route the tongue through the child seat according to the child seat manufacturer’s instructions. Be sure the belt webbing is not twisted. 4. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) for that seating position until you hear a snap and feel the latch engage.
Seating and safety restraints 5. To put the retractor in the automatic locking mode, grasp the shoulder portion of the belt and pull downward until all of the belt is extracted and a click is heard. 6. Allow the belt to retract. The belt will click as it retracts to indicate it is in the automatic locking mode. 7. Pull the lap belt portion across the child seat toward the buckle and pull up on the shoulder belt while pushing down with your knee on the child seat. 8.
Seating and safety restraints Installing child safety seats in the lap belt seating positions 1. Lengthen the lap belt. To lengthen the belt, hold the tongue so that its bottom is perpendicular to the direction of webbing while sliding the tongue up the webbing. 2. Place the child safety seat in the center seating position. 3. Route the tongue and webbing through the child seat according to the child seat manufacturer’s instructions. 4.
Seating and safety restraints 1. Position the child safety seat on the seat cushion. 2. Route the child safety seat tether strap over the back of the seat. For vehicles with adjustable head restraints, route the tether strap under the head restraint and between the head restraint posts, otherwise route the tether strap over the top of the seatback. 3. Locate the correct anchor for the selected seating position. 4. Open the tether anchor cover. 5. Clip the tether strap to the anchor as shown.
Seating and safety restraints Attaching child safety seats with LATCH attachments for child seat anchors Some child safety seats are labeled as LATCH or LATCH-compatible child seats. These seats include two rigid or webbing mounted attachments that connect to two anchors at specific seating positions in your vehicle. This type of child seat eliminates the need to use seat belts to attach the child seat. For forward-facing child seats, the tether strap must also be attached to the proper tether anchor point.
Seating and safety restraints Attach the lower anchors for child seat installation or lower anchors for child seat installation-compatible child seat only to the appropriate locations shown. If you install a child seat with rigid LATCH attachments, do not tighten the tether strap enough to lift the child seat off the seat when the child is seated in it. Keep the tether strap just snug without raising the front of the child seat.
Starting PREPARING TO START YOUR VEHICLE Engine starting is controlled by the powertrain control system. This system meets all Canadian Interference-Causing Equipment standard requirements regulating the impulse electrical field strength of radio noise. When starting a fuel-injected engine, avoid pressing the accelerator before or during starting. Only use the accelerator when you have difficulty starting the engine. For more information on starting the vehicle, refer to Starting the engine in this chapter.
Starting 3. Make sure the gearshift is in P (Park). P R N D D 1 4. Make sure the parking brake is set. 5. Turn the key to 4 (ON) without 3 turning the key to 5 (START). 2 If there is difficulty in turning the key, firmly rotate the steering wheel 4 left and right until the key turns 1 freely.
Starting • If the driver’s safety belt is fastened, the light may not illuminate. STARTING THE ENGINE NOTE: Whenever you start your vehicle, release the key as soon as the engine starts. Excessive cranking could damage the starter. 1. Turn the key to 5 (START) 3 without pressing the accelerator 2 pedal and release as soon as the engine starts. The key will return to 4 4 (ON). 1 2.
Starting Cold starting performance can also be improved with the use of an engine block heater. The engine block heater is available as a Ford option and can also be obtained from your Ford dealer. Consult the engine block heater section for proper use of the engine block heater.
Starting Guarding against exhaust fumes Although odorless and colorless, carbon monoxide is present in exhaust fumes. Take precautions to avoid its dangerous effects. If you ever smell exhaust fumes of any kind inside your vehicle, have your dealer inspect and fix your vehicle immediately. Do not drive if you smell exhaust fumes. These fumes are harmful and could kill you.
Driving BRAKES Your service brakes are self-adjusting. Refer to the scheduled maintenance guide for scheduled maintenance. Occasional brake noise is normal and often does not indicate a performance concern with the vehicle’s brake system. In normal operation, automotive brake systems may emit occasional or intermittent squeal or groan noises when the brakes are applied.
Driving ABS warning lamp ABS The ABS warning lamp in the instrument cluster momentarily illuminates when the ignition is turned to the ON position. If the light does not illuminate momentarily at start up, remains on or continues to flash, the ABS needs to be serviced. With the ABS light on, the anti-lock ! P brake system is disabled and normal braking is still effective unless the BRAKE brake warning light also remains illuminated with parking brake released.
Driving Parking brake Apply the parking brake whenever the vehicle is parked. To set the parking brake, press the parking brake pedal down until the pedal stops. The BRAKE warning lamp in the instrument cluster illuminates and remains illuminated (when the ignition is turned ON) until the parking brake is released. ! P BRAKE Always set the parking brake fully and make sure that the gearshift is securely latched in P (Park). The parking brake is not recommended to stop a moving vehicle.
Driving Pull the release lever to release the brake. Driving with the parking brake on will cause the brakes to wear out quickly and reduce fuel economy. TRACTION CONTROLY (IF EQUIPPED) Your vehicle may be equipped with the optional Traction Controly system. This system helps you maintain the stability and steerability of your vehicle. It is especially useful on slippery and/or hilly road surfaces. The system operates by detecting and controlling wheel spin.
Driving During Traction Controly operation, the traction control active light will illuminate, you may hear an electric motor type of sound coming from the engine compartment and the engine will not “rev-up” when you push further on the accelerator. This is normal system behavior. The Traction Controly on/off switch, located on the right side of the instrument cluster, illuminates O OFF when the system is turned F T/C OFF.
Driving • • • • high crown in center of road high crosswinds wheels out of alignment loose or worn suspension components AUTOMATIC TRANSAXLE OPERATION Brake-shift interlock This vehicle is equipped with a brake-shift interlock feature that prevents the gearshift lever from being moved from P (Park) when the ignition is in the ON position unless brake pedal is depressed. If you cannot move the gearshift lever out of P (Park) with ignition in the ON position and the brake pedal depressed: 1.
Driving Always set the parking brake fully and make sure the gearshift is latched in P (Park). Turn off the ignition whenever you leave your vehicle. If the parking brake is fully released, but the brake warning lamp remains illuminated, the brakes may not be working properly. See your dealer or a qualified service technician. Driving with an automatic overdrive transaxle Your automatic transaxle electronically controls the shift feel by using an adaptive learning strategy.
Driving Hold the brake pedal down while you move the gearshift lever from P (Park) to another position. If you do not hold the brake pedal down, your vehicle may move unexpectedly and injure someone. Understanding gearshift positions P (Park) Always come to a complete stop before shifting into P (Park). Make sure the gearshift lever is securely latched in P (Park). This locks the transaxle and prevent the front wheels from rotating.
Driving N (Neutral) With the gearshift lever in the N (Neutral) position, the vehicle can be started and is free to roll. Hold the brake pedal down while in this position. P R N D D 1 (Overdrive) The (Overdrive) position is the P R N D D 1 normal driving position for an automatic overdrive transaxle. When in the (Overdrive) position, the transaxle works the same way as when in D (Drive).
Driving When to use D (Drive) The D (Drive) position eliminates the needless shifting back and forth between third and fourth gears that your vehicle may do when driving on hilly terrain. It also gives more engine braking than overdrive to slow your vehicle on downgrades. 1 (First) Use 1 (First) for when added engine braking is desired when descending steep hills. The automatic transaxle will shift to the proper gear to ascend any grade without any need to shift to 1 (First).
Driving When parking, do not use the gearshift in place of the parking brake. Always set the parking brake fully and make sure that the gearshift is securely latched in Park (P). Turn off the ignition whenever you leave your vehicle. Never leave your vehicle unattended while it is running. If you do not take these precautions, your vehicle may move unexpectedly and injure someone.
Driving • Maximum Trailer Weight: Maximum weight of a trailer the loaded vehicle (including occupants and cargo) is permitted to tow. It is determined by subtracting the weight of the loaded trailer towing vehicle from the GCWR for the towing vehicle. • Trailer Weight Range: Specified weight range that the trailer must fall within that ranges from zero to the maximum trailer weight rating. Remember to figure in the tongue load of your loaded trailer when figuring the total weight.
Driving Once through the water, always try the brakes. Wet brakes do not stop the vehicle as effectively as dry brakes. Drying can be improved by moving your vehicle slowly while applying light pressure on the brake pedal. Driving through deep water where the transmission vent tube is submerged may allow water into the transmission and cause internal transmission damage. TRAILER TOWING Your vehicle is classified as a light duty towing vehicle.
Driving Model Sedan Wagon 3.0L 4-Valve Duratec Engine Passenger Luggage Load - #/kg (lbs.) Load - kg (lbs.) 5/340 (750) 0 2/135 (300) 70 (150) 2/135 (300) 0 5/340 (750) 70 (150) 2/135 (300) 70 (150) 2/135 (300) 0 Max Trailer Wt.- kg (lbs.) 590 (1 300) 725 (1 600) 795 (1 750) 455 (1 000) 660 (1 450) 725 (1 600) The above chart is based on the specified vehicle at a maximum GCW (Vehicle weight + Trailer weight) equal to 2 470 kg (5 450 lbs.).
Driving Trailer brakes Electric brakes and manual, automatic or surge-type trailer brakes are safe if installed properly and adjusted to the manufacturer’s specifications. The trailer brakes must meet local and Federal regulations. Do not connect a trailer’s hydraulic brake system directly to your vehicle’s brake system. Your vehicle may not have enough braking power and your chances of having a collision greatly increase. The braking system of the tow vehicle is rated for operation at the GVWR not GCWR.
Driving • If you are driving down a long or steep hill, shift to a lower gear. Do not apply the brakes continuously, as they may overheat and become less effective. • The trailer tongue weight should be 10% of the loaded trailer weight. • After you have traveled 80 km (50 miles), thoroughly check your hitch, electrical connections and trailer wheel lug nuts. • When stopped in traffic for long periods of time in hot weather, place the gearshift in P (Park) and increase idle speed.
Driving LUGGAGE RACK (IF EQUIPPED) The rear cross-bar can be adjusted to fit the item being carried. The front cross-bar does not move. Do not load more than 44 kg (100 lbs.) on the luggage rack. To adjust cross-bar position: 1. Loosen the thumbwheel at both ends of the cross-bar. 2. Slide the cross-bar to the desired location. 3. Tighten the thumbwheel at both ends of the cross-bar. Use adjustable tie down loops to secure the load.
Roadside emergencies Getting roadside assistance To fully assist you should you have a vehicle concern, Ford Motor Company offers a complimentary roadside assistance program. This program is separate from the New Vehicle Limited Warranty. The service is available: • 24–hours, seven days a week • for the Basic warranty period (Canada) or New Vehicle Limited Warranty period (U.S.
Roadside emergencies Roadside coverage beyond basic warranty In the United States, you may purchase additional roadside assistance coverage beyond this period through the Ford Auto Club by contacting your Ford or Lincoln Mercury dealer. Similarly in Canada, for uninterrupted Roadside Assistance coverage, you may purchase extended coverage prior to your Basic Warranty’s Roadside Assistance expiring. For more information and enrollment, contact 1–877–294–2582 or visit our website at www.ford.ca.
Roadside emergencies If your vehicle is a sedan, the fuel pump shut-off switch is located on the right side of the trunk behind the trunk liner. If your vehicle is a wagon, the fuel pump shut-off switch is located behind the service panel on the right side of the cargo area. Use the following procedure to reset the fuel pump shut-off switch. 1. Turn the ignition to the OFF position. 2. Check the fuel system for leaks. 3.
Roadside emergencies FUSES AND RELAYS Fuses If electrical components in the vehicle are not working, a fuse may have blown. Blown fuses are identified by a broken wire within 15 the fuse. Check the appropriate fuses before replacing any electrical components. NOTE: Always replace a fuse with one that has the specified amperage rating. Using a fuse with a higher amperage rating can cause severe wire damage and could start a fire.
Roadside emergencies 33 37 41 32 36 40 35 39 PULL TAB TO RELEASE 38 42 14 18 22 26 30 13 17 21 25 29 11 15 19 23 27 9 12 16 20 24 28 10 8 6 5 7 4 3 2 1 S E E OW NE RS MA NU AL CONS UL TE R L A GUID E Passenger compartment fuse panel The fuse panel is located below and to the left of the steering wheel by the brake pedal. Remove the panel cover to access the fuses. To remove a fuse use the fuse puller tool provided on the fuse panel cover. The fuses are coded as follows.
Roadside emergencies Fuse/Relay Location 12 13 14 15 16 Fuse Amp Rating 10A 20A — 30A 15A 17 15A 18 19 20 21 22 — — — — 20A 23 24 25 26 10A 15A 2A 10A 27 10A 28 29 30 31 32 10A 15A 15A — 10A 33 34 — — Passenger Compartment Fuse Panel Description Heated Mirrors, Rear Defrost Switch Power Point Not Used Front Wiper Motor Flasher and GEM Power, Integrated Control Panel (ICP) Power, RCC Memory, Cluster Stop Lamp, Speed Control Deactivating Switch Not Used Not Used Not Used Not Used Deck Lid Releas
Roadside emergencies Fuse/Relay Location 35 36 37 38 39 40 41 42 Fuse Amp Rating — 15A 15A 5A — — — — Passenger Compartment Fuse Panel Description Not Used Turn Signals, Back-up Lamps Transmission Position Switch GEM Park Neutral Switch Not Used Not Used Not Used Not Used Power distribution box The power distribution box is located in the engine compartment. The power distribution box contains high-current fuses that protect your vehicle’s main electrical systems from overloads.
32 31 33 30 25 29 24 14 13 28 27 26 23 12 11 15 16 17 18 19 20 21 22 8 10 7 9 6 5 2 4 1 3 Roadside emergencies The high-current fuses are coded as follows.
Roadside emergencies Fuse/Relay Location 21 22 23 24 25 26 27 28 Fuse Amp Rating 15 A* 10A* — — — 10A* 5A* 15A* 29 — 30 — 31 — 32 — 33 — * Mini Fuses ** Maxi Fuses Power Distribution Box Description Left Headlamp A/C Clutch Relay, PCM Keep Alive Power Starter Motor Relay Low Speed Fan Relay Wiper Speed Relay Generator Rear Control Unit, Antenna HEGO Sensor Transmission Shift Solenoid, Canister Vent, A/C Clutch Relay, Thermactor Bypass Solenoid Wiper Park Relay Fuel Pump Relay PCM Power Relay High Speed F
Roadside emergencies When driving with the temporary spare tire do not: • exceed 80 km/h (50 mph) under any circumstances • load the vehicle beyond maximum vehicle load rating listed on the Safety Compliance Label • tow a trailer • use tire chains • drive through an automatic car wash, because of the vehicle’s reduced ground clearance • try to repair the temporary spare tire or remove it from its wheel • use the wheel for any other type of vehicle Tire change procedure 1.
Roadside emergencies • In the sedan, these are located in the trunk cargo area storage compartment. • In the wagon, they are stored in the left side rear trim panel for the temporary spare and in the floor cargo area storage compartment for the full size spare. 3. If equipped with a wheel cover that’s bolted on, loosen the five plastic nuts with the lug nut wrench. 4. Remove the center ornament or wheel cover from the wheel with the tapered end of the wheel lug nut wrench that came with your vehicle.
Roadside emergencies 5. Loosen each wheel lug nut one-half turn counterclockwise but do not remove them until the wheel is raised off the ground. 6. Put the jack in the jack notch next to the door of the tire you are changing. Turn the jack handle clockwise until the wheel is completely off the ground. 7. Remove the lug nuts with the lug nut wrench. 8. Replace the flat tire with the spare tire, making sure the valve stem is facing outward. Reinstall lug nuts until the wheel is snug against the hub.
Roadside emergencies 11. Return the flat tire, jack and lug wrench to their proper storage locations. Make sure the jack is fastened so it does not rattle when you drive. 12. Unblock the wheels. JUMP STARTING YOUR VEHICLE The gases around the battery can explode if exposed to flames, sparks, or lit cigarettes. An explosion could result in injury or vehicle damage. Batteries contain sulfuric acid which can burn skin, eyes, and clothing, if contacted. Do not attempt to push-start your vehicle.
Roadside emergencies 3. Park the booster vehicle close to the hood of the disabled vehicle making sure the two vehicles do not touch. Set the parking brake on both vehicles and stay clear of the engine cooling fan and other moving parts. 4. Check all battery terminals and remove any excessive corrosion before you attach the battery cables. Ensure that vent caps are tight and level. 5. Turn the heater fan on in both vehicles to protect any electrical surges. Turn all other accessories off.
Roadside emergencies + + – – 3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery. + + – – 4. Make the final connection of the negative (-) cable. Make the connection to an exposed metal part of the stalled vehicle’s engine, away from the battery and the carburetor/fuel injection system. Do not use fuel lines, engine rocker covers or the intake manifold as grounding points.
Roadside emergencies Jump starting 1. Start the engine of the booster vehicle and run the engine at moderately increased speed. 2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both engines for an additional three minutes before disconnecting the jumper cables. Removing the jumper cables + + – – Remove the jumper cables in the reverse order that they were connected. 1. Remove the jumper cable from the ground metal surface. + + – – 2.
Roadside emergencies + + – – 3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’s battery. + + – – 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’s battery. After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn its idle conditions.
Roadside emergencies WRECKER TOWING If you need to have your vehicle towed, contact a professional towing service or, if you are a member, your roadside assistance center. It is recommended that your vehicle be towed with a wheel lift or flatbed equipment. Do not tow with a slingbelt. Ford Motor Company has not approved a slingbelt towing procedure.
Maintenance and care SERVICE RECOMMENDATIONS To help you service your vehicle: • We highlight do-it-yourself items in the engine compartment for easy location. • We provide a scheduled maintenance guide which makes tracking routine service easy. If your vehicle requires professional service, your dealership can provide the necessary parts and service. Check your Warranty Guide to find out which parts and services are covered.
Maintenance and care Note: Do not start your engine with the air cleaner removed and do not remove it while the engine is running. OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located under the bottom of the instrument panel. 2. Go to the front of the vehicle and release the auxiliary latch located in the center between the hood and the grille. 3. Lift the hood until the lift cylinders hold it open.
Maintenance and care IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 3.0L V6 Vulcan engine 9 8 1. 2. 3. 4. 5. 6. 7. 8. 9.
Maintenance and care 3.0L DOHC V6 Duratec engine 8 7 1. 2. 3. 4. 5. 6. 7. 8. 9.
Maintenance and care ENGINE OIL Checking the engine oil Refer to the scheduled maintenance guide for the appropriate intervals for checking the engine oil. 1. Make sure the vehicle is on level ground. 2. Turn the engine off and wait a few minutes for the oil to drain into the oil pan. 3. Set the parking brake and ensure the gearshift is securely latched in P. 4. Open the hood. Protect yourself from engine heat. 5. Locate and carefully remove the engine oil indicator (dipstick). MIN 1QT MAX FULL 6.
Maintenance and care • If the oil level is below the add 1QT or MIN mark, add enough oil to raise the level within the 1QT-FULL or the MIN-MAX range (depending on application). • Oil levels above the F in FULL or above the MAX mark, may cause engine damage. Some oil must be removed from the engine by a service technician. 7. Put the indicator back in and ensure it is fully seated. Adding engine oil 1. Check the engine oil. For instructions, refer to Checking the engine oil in this chapter. 2.
Maintenance and care Engine oil and filter recommendations Look for this certification trademark. SAE 5W-20 engine oil is recommended. Only use oils “Certified For Gasoline Engines” by the American Petroleum Institute (API). Use Motorcraft or an equivalent oil meeting Ford specification WSS-M2C153–H. SAE 5W-20 oil provides optimum fuel economy and durability performance meeting all requirements for your vehicle’s engine. Do not use supplemental engine oil additives, oil treatments or engine treatments.
Maintenance and care BRAKE FLUID Checking and adding brake fluid Brake fluid should be checked and refilled as needed. Refer to the scheduled maintenance guide for the service interval schedules. 1. Clean the reservoir cap before removal to prevent dirt or water from entering the reservoir. 2. Visually inspect the fluid level. 3. If necessary, add brake fluid from a clean un-opened container until MAX the level reaches MAX. Do not fill above this line. 4.
Maintenance and care WINDSHIELD WASHER FLUID Washer fluid Check the washer fluid whenever you stop for fuel. The reservoir is highlighted with a symbol. If the level is low, add enough fluid to fill the reservoir. In very cold weather, do not fill the reservoir all the way. Only use a washer fluid that meets Ford specification . Refer to Lubricant specifications in the Capacities and specifications chapter.
Maintenance and care Checking and adding washer fluid for the liftgate (if equipped) The opening for the reservoir is located on the passenger side under the tail lamp. Refill this reservoir with the same fluid you use for your windshield. ENGINE COOLANT Checking engine coolant The concentration and level of engine coolant should be checked at the mileage intervals listed in the scheduled maintenance guide.
Maintenance and care • Protection against rust and other forms of corrosion. • Enables calibrated gauges to work properly. When the engine is cold, check the level of the engine coolant in the reservoir. • The engine coolant should be at the “cold fill level” or within the “cold fill range” as listed on the engine coolant reservoir (depending upon application). • Refer to the Scheduled Maintenance Guide for service interval schedules.
Maintenance and care Adding engine coolant When adding coolant, make sure it is a 50/50 mixture of engine coolant and distilled water. Add the mixture to the coolant reservoir, when the engine is cool, until the appropriate fill level is obtained. Do not add engine coolant when the engine is hot. Steam and scalding liquids released from a hot cooling system can burn you badly. Also, you can be burned if you spill coolant on hot engine parts.
Maintenance and care • Do not use alcohol, methanol or brine or any engine coolants mixed with alcohol or methanol antifreeze (coolant). Alcohol and other liquids can cause engine damage from overheating or freezing. • Do not add extra inhibitors or additives to the coolant. These can be harmful and compromise the corrosion protection of the engine coolant. • Do not mix with recycled coolant unless from a Ford-approved recycling process (see Use of Recycled Engine Coolant section).
Maintenance and care Whenever coolant has been added, the coolant level in the coolant reservoir should be checked the next few times you drive the vehicle. If necessary, add enough 50/50 concentration of engine coolant and distilled water to bring the liquid level to the proper level. If you have to add more than 1.0 liter (1.0 quart) of engine coolant per month, have your dealer check the engine cooling system. Your cooling system may have a leak.
Maintenance and care • Refer to the chart on the coolant container to ensure the coolant concentration in your vehicle will provide adequate freeze protection at the temperatures in which you drive in the winter months. If you drive in extremely hot climates: • It is still necessary to maintain the coolant concentration above 40%. • NEVER decrease the coolant concentration below 40%.
Maintenance and care 1. Start the engine and let it run until it reaches normal operating temperature (the engine coolant temperature gauge indicator will be near the center of the normal area between H and C). 2. While the engine idles, turn the steering wheel left and right several times. 3. Turn the engine off. Perform steps 4 and 5 following the procedure for your engine. 3.0L V6 Vulcan engine 4. Check the fluid level on the dipstick. It should be between the arrows in the FULL HOT range.
Maintenance and care TRANSMISSION FLUID Checking automatic transmission fluid Refer to your scheduled maintenance guide for scheduled intervals for fluid checks and changes. Your transaxle does not consume fluid. However, the fluid level should be checked if the transaxle is not working properly, i.e., if the transaxle slips or shifts slowly or if you notice some sign of fluid leakage. Automatic transmission fluid expands when warmed.
Maintenance and care Correct fluid level The transmission fluid should be checked at normal operating temperatures 66°C-77°C (150°F-170°F) on a level surface. The normal operating temperature can be reached after approximately 30 km (20 miles) of driving. The transmission fluid should be in this range if at normal operating DON’T ADD IF IN CROSSHATCH AREA--CHECH WHEN HOT-IDLING temperature (66°C-77°C [150°F-170°F]). High fluid level Fluid levels above the safe range may result in transaxle failure.
Maintenance and care CABIN AIR FILTER (IF EQUIPPED) The particulate air filtration system is designed to reduce the concentration of airborne particles such as dust, spores and pollen in the air being supplied to the interior of the vehicle.
Maintenance and care 1. Release and open the hood. 2. Remove the four clips located on the cowl vent screen.
Maintenance and care 3. Remove the cowl vent screen. 4. Remove the two screws retaining the cowl top inner panel shield. 5. Remove the inner panel shield.
Maintenance and care 6. Remove the filter from the cabin air filter housing. 7. Install the new cabin air filter into the cabin air filter housing.
Maintenance and care 8. Replace the inner panel shield. 9. Replace the two screws retaining the cowl top inner panel shield. 10. Replace the cowl vent screen.
Maintenance and care 11. Replace the four clips located on the cowl vent screen. BATTERY Your vehicle is equipped with a Motorcraft maintenance-free battery which normally does not require additional water during its life of service. However, for severe usage or in high temperature climates, check the battery electrolyte level. Refer to the scheduled maintenance guide for the service interval schedules. Keep the electrolyte level in each cell up to the “level indicator”. Do not overfill the battery cells.
Maintenance and care If your battery has a cover/shield, make sure it is reinstalled after the battery has been cleaned or replaced. For longer, trouble-free operation, keep the top of the battery clean and dry. Also, make certain the battery cables are always tightly fastened to the battery terminals. If you see any corrosion on the battery or terminals, remove the cables from the terminals and clean with a wire brush. You can neutralize the acid with a solution of baking soda and water.
Maintenance and care RN LE TU AD RE 2. Put the gearshift in P (Park), turn off all accessories and start the engine. 3. Run the engine until it reaches normal operating temperature. 4. Allow the engine to idle for at least one minute. 5. Turn the A/C on and allow the engine to idle for at least one minute. 6. With your foot on the brake pedal and with the A/C on, put the vehicle in D (Drive) and allow the engine to idle for at least one minute. 7. Drive the vehicle to complete the relearning process.
Maintenance and care Changing the wiper blades To replace the wiper blades: 1. Pull the wiper arm away from the windshield and lock into the service position. 2. Turn the blade at an angle from the wiper arm. Push the lock pin manually to release the blade and pull the wiper blade down toward the windshield to remove it from the arm. 3. Attach the new wiper to the wiper arm and press it into place until a click is heard.
Maintenance and care U.S. Department of Transportation-Tire quality grades: The U.S. Department of Transportation requires Ford to give you the following information about tire grades exactly as the government has written it. Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course.
Maintenance and care The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, underinflation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure. SERVICING YOUR TIRES Checking the tire pressure • Use an accurate tire pressure gauge. • Check the tire pressure when tires are cold, after the vehicle has been parked for at least one hour or has been driven less than 5 km (3 miles).
Maintenance and care Replacing the tires Replace the tires when the wear band is visible through the tire treads. When replacing full size tires, never mix radial bias-belted, or bias-type tires. Use only the tire sizes that are listed on the Certification or Tire Label. Make sure that all tires are the same size, speed rating, and load-carrying capacity. Use only the tire combinations recommended on the label. If you do not follow these precautions, your vehicle may not drive properly and safely.
Maintenance and care Follow these guidelines when using snow tires and chains: • Use only cable type chains offered by Ford as an accessory or equivalent. SAE class “S” or other conventional link type chains may cause damage to the vehicle’s wheel house and/or body. • Install cable chains securely, verifying that the cables do not touch any wiring, brake lines or fuel lines. • Drive cautiously. If you hear the cables rub or bang against your vehicle, stop and re-tighten the cables.
Maintenance and care Fuel ethanol and gasoline may contain benzene, which is a cancer-causing agent. Observe the following guidelines when handling automotive fuel: • Extinguish all smoking materials and any open flames before fueling your vehicle. • Always turn off the vehicle before fueling. • Automotive fuels can be harmful or fatal if swallowed. Fuels such as gasoline and ethanol are highly toxic and if swallowed can cause death or permanent injury.
Maintenance and care • FFV fuel tanks may contain zero to 85 percent ethanol. Any fuel blends containing gasoline and ethanol should be treated the same as “Fuel Ethanol (E85)”. To identify if your vehicle is an FFV, check your VIN or the label on the inside of your fuel filler door. When checking the VIN look for the engine type identifier (8th character). If your vheicle is an FFV, then the character will be labeled as a “K.
Maintenance and care The flow of fuel through a fuel pump nozzle can produce static electricity, which can cause a fire if fuel is pumped into an ungrounded fuel container. Use the following guidelines to avoid static build-up when filling an ungrounded fuel container: • Place approved fuel container on the ground. • DO NOT fill a fuel container while it is in the vehicle (including the cargo area). • Keep the fuel pump nozzle in contact with the fuel container while filling.
Maintenance and care The fuel system may be under pressure. If the fuel filler cap is venting vapor or if you hear a hissing sound, wait until it stops before completely removing the fuel filler cap. Otherwise, fuel may spray out and injure you or others. If you do not use the proper fuel filler cap, excessive pressure or vacuum in the fuel tank may damage the fuel system or cause the fuel cap to disengage in a collision, which may result in possible personal injury.
Maintenance and care FFV engine (if equipped) Your vehicle is designed to use Fuel Ethanol(E85), “Regular” unleaded gasoline or any percentage of the two fuels combined. U.S. government regulations require fuel ethanol dispensing pumps to have a small, square, orange and black label with the common abbreviation E85 or the appropriate percentage for that region. Use of other fuels such as Fuel Methanol may cause powertrain damage, a loss of vehicle performance, and your warranty may be invalidated.
Maintenance and care your VIN or the label on the inside of your fuel filler door. When checking the VIN, look for the engine type identifier (8th character). If your vehicle is an FFV, then the character will be labeled as a “K.” Standards for fuel ethanol have been developed to provide FFVs the best possible performance, safety and durability.
Maintenance and care ESSENTIALS OF GOOD FUEL ECONOMY Measuring techniques Your best source of information about actual fuel economy is you, the driver. You must gather information as accurately and consistently as possible. Fuel expense, frequency of fillups or fuel gauge readings are NOT accurate as a measure of fuel economy. We do not recommend taking fuel economy measurements during the first 1 600 km (1 000 miles) of driving (engine break-in period).
Maintenance and care Calculating fuel economy 1. Fill the fuel tank completely and record the initial odometer reading (in kilometers or miles). 2. Each time you fill the tank, record the amount of fuel added (in liters or gallons). 3. After at least three to five tank fill-ups, fill the fuel tank and record the current odometer reading. 4. Subtract your initial odometer reading from the current odometer reading. 5.
Maintenance and care • Using the air conditioner or defroster may reduce fuel economy. • You may want to turn off the speed control in hilly terrain if unnecessary shifting between third and fourth gear occurs. Unnecessary shifting of this type could result in reduced fuel economy. • Warming up a vehicle on cold mornings is not required and may reduce fuel economy. • Resting your foot on the brake pedal while driving may reduce fuel economy. • Combine errands and minimize stop-and-go driving.
Maintenance and care EPA window sticker Every new vehicle should have the EPA window sticker. Contact your dealer if the window sticker is not supplied with your vehicle. The EPA window sticker should be your guide for the fuel economy comparisons with other vehicles. It is important to note the box in the lower left corner of the window sticker. These numbers represent the Range of L/100 km (MPG) expected on the vehicle under optimum conditions.
Maintenance and care Exhaust leaks may result in entry of harmful and potentially lethal fumes into the passenger compartment. Do not make any unauthorized changes to your vehicle or engine. By law, vehicle owners and anyone who manufactures, repairs, services, sells, leases, trades vehicles, or supervises a fleet of vehicles are not permitted to intentionally remove an emission control device or prevent it from working.
Maintenance and care • Tail lamps • Brakelamps • High-mount brakelamp • Turn signals • Backup lamps • License plate lamp Do not remove lamp bulbs unless they will be replaced immediately. If a bulb is removed for an extended period of time, contaminants may enter the lamp housings and affect performance. Replacing headlamp bulbs To remove the headlamp bulb: 1. Make sure headlamp switch is in OFF position. 2. Remove the bolt from the headlamp housing. 3.
Maintenance and care 4. Remove the protective dust shield from the housing by turning the dust shield counterclockwise (when viewed from the rear). 5. Disconnect the electrical connector from the bulb by pulling rearward. 6. Remove the bulb retaining ring by rotating it counterclockwise. 7. Remove the old bulb from the lamp assembly by pulling it straight out of the lamp assembly.
Maintenance and care To install the new bulb: Handle a halogen headlamp bulb carefully and keep out of children’s reach. Grasp the bulb only by its plastic base and do not touch the glass. The oil from your hand could cause the bulb to break the next time the headlamps are operated. 1. Install the new bulb in lamp assembly by pushing straight in with the flat surface of the bulb’s plastic base facing upward.
Maintenance and care Replacing front parking lamp/turn signal/cornering lamp bulbs 1. Make sure the headlamp control is in the OFF position. 2. Remove the bolt from the headlamp housing. 3. At the back of the headlamp, pry up and remove the two retainer pins to release the headlamp assembly from the vehicle and pull headlamp forward. 4. Rotate the bulb socket counterclockwise and remove it from the lamp assembly. 5. Carefully pull bulb straight out of the socket and push in the new bulb. 6.
Maintenance and care Replacing high-mount brakelamp bulbs — Sedan only • TYPE A 1. Open trunk and locate the insulator under the rear window. Note the number of the push pins before removal. 2. Remove the insulator by carefully prying out the push pins to gain access to the bulb sockets. 3. Remove the bulb socket by rotating it counterclockwise and pulling it down from the lamp assembly. 4. Carefully pull bulb straight out of socket and push in new bulb. 5.
Maintenance and care Replacing high-mount brakelamp bulbs — Wagon only 1. Open liftgate. 2. Remove two screw covers, screws and handle from liftgate. 3. Remove two screws and the lower trim panel from the liftgate. 4. Remove the upper trim panel. 5. Remove the rubber plug from the lower access hole in the upper portion of the liftgate. 6. Remove four nuts from the lamp assembly.
Maintenance and care 7. Carefully lift the lamp assembly away from the liftgate. 8. Remove the bulb socket by rotating it counterclockwise and pulling it out from the lamp assembly. 9. Carefully pull the bulb straight out of the socket and push in the new bulb. 10. To complete installation, follow the removal procedure in reverse order. Replacing license plate lamp bulbs Wagon 1. Remove screw and the license plate lamp assembly from liftgate. 2. Remove bulb socket by turning counterclockwise. 3.
Maintenance and care Sedan 1. Remove two screws, grommets and the license plate lamp assembly from the trunk lid. 2. Carefully pull the bulb from the socket and push in the new bulb. 3. Install the lamp assembly on trunk lid with two grommets, ensuring the grommets are pushed all the way in to the trunk lid and secure with two screws.
Maintenance and care 4. Remove the bulb socket by rotating it counterclockwise, then pulling it out of the lamp assembly. 5. Pull the bulb from the socket and push in the new bulb. 6. Install the bulb socket into the lamp assembly by rotating it clockwise. 7. Install the lamp assembly on the vehicle with three nut and washer assemblies ensuring the washers on the nuts are flush with the body to prevent water from entering the trunk. 8.
Maintenance and care Using the right bulbs Replacement bulbs are specified in the chart below. Headlamp bulbs must be marked with an authorized “D.O.T.” for North America and an “E” for Europe to assure lamp performance, light brightness and pattern and safe visibility. The correct bulbs will not damage the lamp assembly or void the lamp assembly warranty and will provide quality bulb burn time.
Maintenance and care AIMING THE HEADLAMPS The headlamps on your vehicle are properly aimed at the assembly plant. If your vehicle has been in an accident the alignment of your headlamps should be checked by a qualified service technician. Vertical aim adjustment 1. Park the vehicle on a level surface approximately 7.6 meters (25 feet) from a vertical wall or screen directly in front of it.
Maintenance and care 4. On the wall or screen you will observe an area of high intensity light. The top of the high intensity area should touch the horizontal reference line, if not, the beam will need to be adjusted. To see a clearer light pattern for adjusting, you may want to block the light from one headlamp while adjusting the other. 5. Locate the vertical adjuster on each headlamp. Using a 4 mm wrench, turn the adjuster either clockwise (to adjust down) or counterclockwise (to adjust up).
Maintenance and care CLEANING AND CARING FOR YOUR VEHICLE Refer to the Customer Assistance chapter for a list of Ford-approved cleaners, polishes and waxes. Washing your vehicle Wash your vehicle regularly with cold or lukewarm water. Never use strong detergents or soap. If your vehicle is particularly dirty, use a quality car wash detergent. Always use a clean sponge, washing glove or similar device and plenty of water for best results.
Maintenance and care Use only carnauba or synthetic-based waxes. Use a cleaning fluid with a clean cloth to remove any bugs before waxing your vehicle. Use tar remover to remove any tar spots. Avoid getting wax on the windshield, or on any surfaces which appear coarse or bumpy. If you have wax applied at a commercial car wash, it is recommended that you clean the wiper blades and windshield as described in Cleaning the wiper blades and windshield.
Maintenance and care Cleaning the exterior lamps Wash with the same detergent as the exterior of your vehicle. If necessary, use a tar remover such as Ford Extra Strength Tar and Road Oil Remover (B7A-19520–AA). To avoid scratching the lamps, do not use a dry paper towel, chemical solvents or abrasive cleaners. Cleaning the windshield, wiper blades and rear window If the wiper blades do not wipe properly, clean the wiper blade rubber element with undiluted windshield washer solution or a mild detergent.
Maintenance and care • 3.0L Vulcan engine • 3.0L Duratec engine • Never wash or rinse the engine while it is running; water in the running engine may cause internal damage.
Maintenance and care Cleaning the instrument panel Clean with a damp cloth, then dry with a dry cloth. Avoid cleaner or polish that increases the gloss of the upper portion of the instrument panel. The dull finish in this area helps protect the driver from undesirable windshield reflection. Do not use chemical solvents or strong detergents when cleaning the steering wheel or instrument panel to avoid contamination of the air bag system.
Maintenance and care Cleaning and maintaining the safety belts Clean the safety belts with a mild soap solution recommended for cleaning upholstery or carpets. Do not bleach or dye the belts, because these actions may weaken the belt webbing. Check the safety belt system periodically to make sure there are no nicks, tears or cuts. If your vehicle has been involved in an accident, refer to the Safety belt maintenance section in the Seating and safety restraints chapter.
Capacities and specifications MOTORCRAFT PART NUMBERS Component Air filter element 1 Fuel filter Battery (standard) Battery (optional) Oil filter PCV valve Spark plugs 1 2 3.0L V6 Vulcan engine FA-1683 3.0L FFV V6 engine FA-1683 3.0L DOHC V6 Duratec engine FA-1683 FG-1006 BXT-58R FG-1006 BXT-58R FG-1006 BXT-36R BXT-36R N/A N/A FL-400-S EV-228 AWSF-32PP FL-400-S EV-228 AGSF-22PP FL-820-S EV-243 AWSF-32F 3 3 Do not use oil-impregnated air filter elements.
Capacities and specifications REFILL CAPACITIES Fluid Brake fluid Engine coolant1 Engine oil (includes filter change) Ford Part Application Name Motorcraft All High Performance DOT 3 Motor Vehicle Brake Fluid Motorcraft 3.0L V6 Vulcan Premium engine Engine Coolant (green-colored) or Motorcraft 3.0L V6 Duratec Premium Gold engine Engine Coolant (yellow-colored) Motorcraft SAE 3.0L V6 Vulcan engine 5W-20 Super Premium 3.
Capacities and specifications Fluid Windshield washer fluid Front Windshield washer fluid Rear Ford Part Name Ultra-Clear Windshield Washer Concentrate Ultra-Clear Windshield Washer Concentrate Application Capacity All 2.8L (94.7 oz.) Wagon 1.8L (60.9 oz.) 1 Add the coolant type originally equipped in your vehicle.
Capacities and specifications Ford Part Name or equivalent Constant velocity CV Joint Grease joints (High Temp.
Capacities and specifications ENGINE DATA Engine Cubic inches Required fuel Firing order Spark plug gap Ignition system Compression ratio 3.0L V6 Vulcan engine 182 87 octane 1-4-2-5-3-6 1.07-1.17 mm (0.042-0.046 inch) EDIS 9.3:1 3.0L FFV V6 engine 182 87 octane or Ethanol (E 85) 1-4-2-5-3-6 1.07-1.17 mm (0.042-0.046 inch) EDIS 9.3:1 3.0L DOHC V6 Duratec engine 183 87 octane 1-4-2-5-3-6 1.3-1.4 mm (0.052-0.056 inch) EDIS 10.
Capacities and specifications 3 5 2 4 1 227
Capacities and specifications 4 1 IDENTIFYING YOUR VEHICLE Certification label The National Highway Traffic Safety Administration Regulations require that a Certification label be affixed to a vehicle and prescribe where the Certification label may be located. The Certification label is located on the front door latch pillar on the driver’s side.
Capacities and specifications Vehicle identification number The vehicle identification number is attached to a metal tag and is located on the driver side instrument panel. (Please note that in the graphic XXXX is representative of your vehicle identification number.) XXXXXXXXXXXXXXXXX Engine number The engine number (the last eight numbers of the vehicle identification number) is stamped on the engine block, frame and transaxle.
Customer assistance Ford Extended Service Plan You can get more protection for your new car or light truck by purchasing Ford Extended Service Plan (Ford ESP) coverage. Ford ESP is an optional service contract which is backed by Ford Motor Company or Ford Motor Service Company (in the U.S.) and Ford of Canada (in Canada). It provides the following: • Benefits during the warranty period depending on the plan you purchase (such as: reimbursement for rentals; coverage for certain maintenance and wear items).
Customer assistance taken to another dealer. If a particular dealership can not assist you, then contact the Customer Relationship Center. If you have questions or concerns, or are unsatisfied with the service you are receiving, follow these steps: 1. Contact your Sales Representative or Service Advisor at your selling/servicing dealership. 2. If your inquiry or concern remains unresolved, contact the Sales Manager or Service Manager at the dealership. 3.
Customer assistance In the United States: Ford Motor Company Customer Relationship Center 16800 Executive Plaza Drive P.O. Box 6248 Dearborn, Michigan 48121 1-800-521-4140 (TDD for the hearing impaired: 1-800-232-5952) In Canada: Customer Relationship Centre Ford Motor Company of Canada, Limited P.O.
Customer assistance THE DISPUTE SETTLEMENT BOARD (U.S. ONLY) The Dispute Settlement Board is: • an independent, third-party arbitration program for warranty disputes • available free to owners and lessees of qualifying Ford Motor Company vehicles The Dispute Settlement Board may not be available in all states. Ford Motor Company reserves the right to change eligibility limitations, modify procedures and/or to discontinue this service without notice and without incurring obligations per applicable state law.
Customer assistance Board membership The Board consists of: • three consumer representatives • a Ford or Lincoln Mercury dealership representative Consumer candidates for Board membership are recruited and trained by an independent consulting firm. The dealership Board member is chosen from Ford and Lincoln Mercury dealership management, recognized for their business leadership qualities.
Customer assistance You will receive a letter of explanation if your application does not qualify for Board review. Oral presentations If you would like to make an oral presentation, indicate YES to question 6 on the application. While it is your right to make an oral presentation before the Board, this is not a requirement and the Board will decide the case whether or not an oral presentation is made. An oral presentation may be requested by the Board as well.
Customer assistance UTILIZING THE MEDIATION/ARBITRATION PROGRAM (CANADA ONLY) In those cases where you continue to feel that the efforts by Ford and the dealer to resolve a factory-related vehicle service concern have been unsatisfactory, Ford of Canada participates in an impartial third party mediation/arbitration program administered by the Canadian Motor Vehicle Arbitration Plan (CAMVAP).
Customer assistance If your vehicle must be serviced while you are traveling or living in Central or South America, the Caribbean, or the Middle East, contact the nearest Ford dealership. If the dealership cannot help you, write or call: FORD MOTOR COMPANY WORLDWIDE DIRECT MARKET OPERATIONS 1555 Fairlane Drive Fairlane Business Park #3 Allen Park, Michigan 48101 U.S.A. Telephone: (313) 594-4857 FAX: (313) 390-0804 If you are in another foreign country, contact the nearest Ford dealership.
Customer assistance Ford Multi-Purpose Cleaner* Motorcraft Car Wash Concentrate Motorcraft Carlite Glass Cleaner Ford Spot and Stain Remover* Ford Super Premium Tire and Trim Dressing Ford Triple Clean Ford Ultra-Clear Spray Glass Cleaner (not available in Canada) * May be sold with the Motorcraft name FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of genuine Ford accessories are available for your vehicle through your local authorized Ford, Lincoln Mercury or Ford of Canada dealer.
Customer assistance Comfort and convenience Air filtration Cargo nets Cargo organizers Cargo shades (wagon) Engine block heaters Travel equipment Electrochromic inside mirror with compass Electrochromic inside mirror with compass and temperature Factory luggage rack adaptors Framed luggage carrier Removable luggage rack Removable luggage rack adapters Soft luggage carrier Speed control Protection and appearance equipment Car covers Cargo liners Carpet floor mats Flat splash guards Front end covers (full) Mo
Customer assistance • The Federal Communications Commission (FCC) and Canadian Radio Telecommunications Commission (CRTC) regulate the use of mobile communications systems - such as two-way radios, telephones and theft alarms - that are equipped with radio transmitters. Any such equipment installed in your vehicle should comply with FCC or CRTC regulations and should be installed only by a qualified service technician.
Customer assistance IN CALIFORNIA (U.S. ONLY) California Civil Code Section 1793.
Reporting safety defects REPORTING SAFETY DEFECTS (U.S. ONLY) If you believe that your vehicle has a defect that could cause a crash, or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Ford Motor Company. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.
Index A B Accessory delay ..........................63 Air bag supplemental restraint system ........................104, 106, 110 and child safety seats ............107 description ......................106, 110 disposal ....................................112 driver air bag ..........105, 109, 111 indicator light ...................13, 108 operation .................105, 109, 111 passenger air bag ...105, 109, 111 side air bag ..............................110 Air cleaner filter .......................
Index Child safety seats ......................114 attaching with tether straps ..118 in front seat ............................115 in rear seat ......................115, 118 LATCH .....................................120 Cleaning your vehicle ...............216 engine compartment ..............218 exterior ............................216–217 exterior lamps .........................218 instrument cluster lens ..........220 instrument panel ....................220 interior .............................
Index idle speed control ...................185 lubrication specifications ..................224, 226 refill capacities ........................223 service points ..................164–165 starting after a collision .........145 Engine block heater .................125 Engine oil ..................................166 checking and adding ..............166 dipstick ....................................166 filter, specifications ........168, 222 recommendations ...................168 refill capacities .........
Index high beam .............................8, 17 replacing bulbs .......................204 turning on and off ....................17 warning chime ..........................14 Heating ........................................19 heating and air conditioning system .......................................19 Hood ..........................................163 I Ignition .................................52, 226 Infant seats (see Safety seats) .....................114 Inspection/maintenance (I/M) testing .......
Index Locks autolock .....................................78 childproof ..................................63 Lubricant specifications ...224, 226 Lumbar support, seats ...............87 R Mirrors .........................................60 cleaning ...................................217 heated ........................................64 side view mirrors (power) .......64 Moon roof ....................................60 Motorcraft parts ................198, 222 Radio ......................................
Index Servicing your vehicle ..............162 Spark plugs, specifications .....................222, 226 Specification chart, lubricants ...........................224, 226 Speed control ..............................53 Speedometer ...............................14 Starting your vehicle ........122, 124 jump starting ..........................156 Steering wheel tilting .........................................58 T Tachometer .................................15 Tires ...........................
Filling station information Item Required fuel Information Refer to 9Octane recommendations9 in the Maintenance and care chapter. Fuel tank capacity 68.1L (18 gallons) Engine oil capacity (including filter 4.25L (4.5 quarts). Use Motorcraft change)-3.0L V6 Vulcan engine SAE 5W-20 Super Premium Motor Oil, Ford specification WSS-M2C153-H. Engine oil capacity (including filter 5.2L (5.5 quarts). Use Motorcraft change)-3.
Filling station information 1 Use either green-colored Motorcraft Premium Engine Coolant or yellow-colored Motorcraft Premium Gold Engine Coolant. DO NOT USE Ford Extended Life Engine Coolant (orange in color). Refer to Adding engine coolant, in the Maintenance and Care chapter. 2 Ensure the correct automatic transmission fluid is used. Transmission fluid requirements are indicated on the dipstick or on the dipstick handle. MERCONt and MERCONt V are not interchangeable. DO NOT mix MERCONt and MERCONt V.
