Table of Contents Introduction Instrument Cluster 4 12 Warning lights and chimes Gauges 12 16 Entertainment Systems 19 AM/FM stereo AM/FM Stereo single CD/MP3 system In-dash CDX6/MP3 disc Premium/Audiophile Pioneer audio system Tremor IV CD/MP3 audio system Auxiliary input jack Satellite radio information Climate Controls Heater only Manual heating and air conditioning Lights Headlamps Turn signal control Bulb replacement Driver Controls Windshield wiper/washer control Steering wheel adjustment Pow
Table of Contents Seating and Safety Restraints Seating Safety restraints Airbags Child restraints Tires, Wheels and Loading Tire information Tire inflation Tire Pressure Monitoring System (TPMS) Vehicle loading Trailer towing Recreational towing Driving 80 80 83 98 106 117 119 121 134 138 144 154 156 Starting Brakes Transmission operation 156 160 163 Roadside Emergencies 177 Getting roadside assistance Hazard flasher switch Fuel pump shut-off switch Fuses and relays Changing tires Lug nut torque
Table of Contents Maintenance and Specifications Engine compartment Engine oil Battery Engine coolant Fuel information Air filter(s) Part numbers Maintenance product specifications and capacities Engine data 220 222 226 232 234 239 256 257 259 264 Accessories 268 Index 271 All rights reserved.
Introduction CALIFORNIA Proposition 65 Warning WARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. In addition, certain fluids contained in vehicles and certain products of component wear contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
Introduction SAFETY AND ENVIRONMENT PROTECTION Warning symbols in this guide How can you reduce the risk of personal injury to yourself or others? In this guide, answers to such questions are contained in comments highlighted by the warning triangle symbol. These comments should be read and observed. Warning symbols on your vehicle When you see this symbol, it is imperative that you consult the relevant section of this guide before touching or attempting adjustment of any kind.
Introduction SPECIAL NOTICES New Vehicle Limited Warranty For a detailed description of what is covered and what is not covered by your vehicle’s New Vehicle Limited Warranty, refer to the Warranty Guide that is provided to you along with your Owner’s Guide. Special instructions For your added safety, your vehicle is fitted with sophisticated electronic controls. Please read the section Supplemental restraint system (SRS) in the Seating and Safety Restraints chapter.
Introduction Event Data Recording Other modules in your vehicle — event data recorders — are capable of collecting and storing data during a crash or near crash event. The recorded information may assist in the investigation of such an event.
Introduction Notice to owners of pickup trucks and utility type vehicles Utility vehicles have a significantly higher rollover rate than other types of vehicles. Before you drive your vehicle, please read this Owner’s Guide carefully. Your vehicle is not a passenger car. As with other vehicles of this type, failure to operate this vehicle correctly may result in loss of vehicle control, vehicle rollover, personal injury or death. Be sure to read Driving off road in the Driving chapter.
Introduction Middle East/North Africa vehicle specific information For your particular global region, your vehicle may be equipped with features and options that are different from the ones that are described in this Owner’s Guide; therefore, a supplement has been supplied that complements this book. By referring to the pages in the provided supplement, you can properly identify those features, recommendations and specifications that are unique to your vehicle.
Introduction These are some of the symbols you may see on your vehicle.
Introduction Vehicle Symbol Glossary Power Windows Front/Rear Power Window Lockout Child Safety Door Lock/Unlock Interior Luggage Compartment Release Symbol Panic Alarm Engine Oil Engine Coolant Engine Coolant Temperature Do Not Open When Hot Battery Avoid Smoking, Flames, or Sparks Battery Acid Explosive Gas Fan Warning Power Steering Fluid Maintain Correct Fluid Level Emission System Engine Air Filter Passenger Compartment Air Filter Jack Check Fuel Cap Low Tire Pressure Warning MAX
Instrument Cluster WARNING LIGHTS AND CHIMES Warning lights and gauges can alert you to a vehicle condition that may become serious enough to cause expensive repairs. A warning light may illuminate when a problem exists with one of your vehicle’s functions. Many lights will illuminate when you start your vehicle to make sure the bulb works. If any light remains on after starting the vehicle, refer to the respective system warning light for additional information.
Instrument Cluster Check fuel cap: Illuminates when the fuel cap may not be properly installed. Continued driving with this light on may cause the Check Engine warning light to come on. It may take a long period of time for the system to detect an improperly installed or properly re-installed fuel filler cap depending on driving and fuel tank level conditions. Refer to Fuel filler cap in the Maintenance and Specifications chapter.
Instrument Cluster Airbag readiness: If this light fails to illuminate when ignition is turned to ON, continues to flash or remains on, have the system serviced immediately by your authorized dealer. A chime will also sound when a malfunction in the supplemental restraint system has been detected. Safety belt: Reminds you to fasten your safety belt. A BeltMinder威 chime will also sound to remind you to fasten your safety belt.
Instrument Cluster Foglamps: Illuminates when the foglamps are turned on. Refer to Foglamp control in the Lights chapter. Low fuel: Illuminates when the fuel level in the fuel tank is at or near empty (refer to Fuel gauge in this chapter). Door ajar: Illuminates when the ignition is in the ON position and any door is open. Overdrive off (if equipped): O/D Illuminates when the overdrive OFF function of the transmission has been turned off, refer to the Driving chapter.
Instrument Cluster Turn signal: Illuminates when the left or right turn signal or the hazard lights are turned on. If the indicators stay on or flash faster, check for a burned out bulb. High beams: Illuminates when the high beam headlamps are turned on. Key-in-ignition warning chime: Sounds when the key is left in the ignition in the OFF/LOCK or ACCESSORY position and the driver’s door is opened.
Instrument Cluster Engine coolant temperature gauge: Indicates engine coolant temperature. At normal operating temperature, the needle will be in the normal range (between “H” and “C”). If it enters the red section, the engine is overheating. Stop the vehicle as soon as safely possible, switch off the engine and let the engine cool. Never remove the coolant reservoir cap while the engine is running or hot. Odometer: Registers the total miles (kilometers) of the vehicle.
Instrument Cluster Fuel gauge: Indicates approximately how much fuel is left in the fuel tank (when the ignition is in the ON position). The fuel gauge may vary slightly when the vehicle is in motion or on a grade. Proper gauge indication requires the ignition to be in the OFF or ACCESSORY position during refueling, otherwise correct fuel indication after refueling can be slow to update. Also, a minimum of 3 gallons is needed for correct indication after refueling.
Entertainment Systems AUDIO SYSTEMS AM/FM stereo (if equipped) Display preference: You can select Clock mode, which displays the time, or Frequency mode, which displays the current radio frequency, to appear in the radio display. Press CLK repeatedly to toggle between Clock and Frequency modes. If clock mode is selected and a radio function is pressed (i.e. SEEK, TUNE, Memory Presets), the radio information will display momentarily and then again display the time. 1.
Entertainment Systems To set the display mode: Press repeatedly to toggle between Clock mode and frequency mode. 3. AUDIO: Press AUDIO repeatedly to toggle through the following / to make modes and use adjustments in those modes. Bass: Press Treble: Press Balance: Press right speakers. Hours: Press Minute: Press AUDIO AUDIO AUDIO AUDIO AUDIO to decrease/increase the bass setting. to decrease/increase the treble setting. to adjust the audio between the left and to decrease/increase the hours.
Entertainment Systems AM/FM stereo single CD system (if equipped) 1. CD eject: Press to eject the CD. 2. CLK (Clock): Press CLK until SELECT HOUR or SELECT MINS is displayed. MENU to adjust the Press hours/minutes. Press CLK to display the time when the ignition is off. 3. MUTE: Press to mute the playing media. Press again to return to the playing media. 4. MENU: Press MENU repeatedly to toggle through the following / to make an modes and use adjustment in those modes.
Entertainment Systems your original manually set preset stations. When the six strongest stations are filled, the station stored in preset 1 will begin playing. If there are less than six strong stations, the system will store the last one in the remaining presets. Bass: Press Treble: Press Balance: Press right speakers. MENU MENU to decrease/increase the bass setting. to decrease/increase the treble setting.
Entertainment Systems 12. SCAN: Press to toggle between SCAN ON and SCAN OFF. When activated, the system scans up through and plays a brief sampling of available radio stations or CD tracks. Press again to stop. 13. AM/FM: Press to select AM/FM1/FM2 frequency band. 14. ON/OFF/Volume: Press to turn ON/OFF. Turn to increase/decrease volume.
Entertainment Systems AM/FM stereo single CD/MP3 Satellite Compatible system (if equipped) 1. CD eject: Press to eject the CD/MP3. 2. CLK (Clock): Press CLK until SELECT HOUR or SELECT MINS is displayed. MENU to adjust the Press hours/minutes. Press CLK to display the time when the ignition is off. 3. MUTE: Press to mute the playing media. Press again to return to the playing media. 4. MENU: Press MENU repeatedly to scroll through the following / to make an modes and use adjustment in those modes.
Entertainment Systems CATEGORY (Satellite Radio if equipped): Press MENU until the currently active category appears in the display (CATEGORY ALL). In CATEGORY ALL, press / to scroll through the list of available Sirius Categories (Pop, Rock, News, etc.) Press SEEK or SCAN to select the channels within each category. After a category is selected, press SEEK to search for that specific channel. To select a different category, press MENU until CATEGORY ALL appears in the display.
Entertainment Systems In CATEGORY ALL, press / to scroll through the list of available Sirius channel Categories (Pop, Rock, News, etc.). Refer to Category Mode under Menu for further information. Satellite radio is available only with a valid SIRIUS subscription. Check with your authorized dealer for availability. 6. SHUFF (Shuffle): Press to play the current CD/MP3 tracks in random order. In MP3 directory mode, press to play the tracks within the current directory in random order. 7.
Entertainment Systems In Satellite Radio mode (if equipped), press SEEK to seek to the previous/next channel. If a specific category is selected, (Jazz, Rock, SEEK to seek to the previous/next channel in News, etc.), press SEEK to fast seek through the selected category. Press and hold the previous /next channels. SEEK to view the previous/additional In TEXT MODE, press display text. TUNE to select a category. In CATEGORY ALL, press In CATEGORY MODE, press SEEK to select a channel within that category.
Entertainment Systems 15. ON/OFF/Volume: Press to turn ON/OFF. Turn to increase/decrease volume. If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on. 16. CD: Press to enter CD/MP3 mode. If a CD/MP3 is already present in the system, the disc will begin to play. 17. CD slot: Insert a CD/MP3 label side up. CD units are designed to play commercially pressed 4.
Entertainment Systems Premium and Audiophile in-dash CD6/MP3 disc Pioneer audio systems (if equipped) 1. AM/FM: Press to select AM/FM1/FM2 frequency bands. 2. CD: Press to enter CD/MP3 mode. If a CD/MP3 is already in the system, the disc will start playing. 3. EJ (CD eject): To eject an individual CD/MP3, press the eject control and select the correct slot number by pressing the corresponding memory preset. Press and hold to eject all CD/MP3s. 4.
Entertainment Systems 5. MUTE: Press to mute the playing media. Press again to return to the playing media. 6. MENU: Press MENU repeatedly to toggle through the following / to make modes and use adjustment in those modes. Autoset: Allows you to set the strongest local radio stations without losing your original manually set preset stations for AM/FM1/FM2 . Press MENU to access. Use MENU to set. When the six strongest stations are filled, the station stored in preset 1 will begin playing.
Entertainment Systems 9. SHUFF (Shuffle): Press to play the tracks on the current CD/MP3 in random order. In MP3 directory mode, press to play the tracks within the current directory in random order. 10. Compression: In CD/MP3 modes, press to bring loud and soft passages together for a more consistent listening level. 11. REPEAT: Press to repeat the current CD/MP3 track. The selection will repeat continuously until deactivated. Press REPEAT again to deactivate. 12.
Entertainment Systems 18. LOAD: Press to load a CD/MP3. To load a CD/MP3 disc to a specific slot, press LOAD and select the slot number by pressing the corresponding memory preset. Press and hold LOAD to autoload up to six discs. 19. CD slot: Insert a CD/MP3, label side up. CD units are designed to play commercially pressed 4.75 in (12 cm) audio compact discs only. Due to technical incompatibility, certain recordable and re-recordable compact discs may not function correctly when used in Ford CD players.
Entertainment Systems 1. AM/FM: Press to select AM/FM1/FM2 frequency bands. 2. CD: Press to enter CD/MP3 mode. If a CD/MP3 is already in the system, the disc will start playing. 3. AUX: Press AUX to cycle through SAT1, SAT2, SAT3 (Satellite radio modes, if equipped) and LINE IN (Auxiliary audio mode, if equipped). To return to radio mode, press AM/FM. Satellite radio is available only with a valid SIRIUS subscription. Check with your authorized dealer for availability. 4.
Entertainment Systems category, press MENU until CATEGORY ALL appears in the display. Press / to select a different category. Satellite radio is available only with a valid SIRIUS subscription. Check with your authorized dealer for availability. Autoset: Allows you to set the strongest local radio stations without losing your original manually set preset stations for AM/FM1/FM2 . Press MENU to access. Use MENU to set.
Entertainment Systems 10. COMP (Compression): In CD/MP3 modes, press to bring loud and soft passages together for a more consistent listening level. 11. REPEAT: Press to repeat the current CD/MP3 track. The selection will repeat continuously until deactivated. Press REPEAT again to deactivate. 12. FF (Fast forward): Press to manually advance in a CD/MP3 track. 13. REW (Rewind): Press to manually reverse in a CD/MP3 track. REW 1 14.
Entertainment Systems In TEXT MODE, press SEEK to view the previous/additional display text. TUNE to select a category. In CATEGORY ALL, press SEEK to select a channel within In CATEGORY MODE, press that category. Satellite radio is available only with a valid SIRIUS subscription. Check with your authorized dealer for availability. 16. TEXT/SCAN: In radio and CD mode, press for a brief sampling of radio stations or CD tracks. Press again to stop.
Entertainment Systems 19. CD slot: Insert a CD/MP3, label side up. CD units are designed to play commercially pressed 4.75 in (12 cm) audio compact discs only. Due to technical incompatibility, certain recordable and re-recordable compact discs may not function correctly when used in Ford CD players. Irregular shaped CDs, CDs with a scratch protection film attached, and CDs with homemade paper (adhesive) labels should not be inserted into the CD player. The label may peel and cause the CD to become jammed.
Entertainment Systems 2. CD: Press to enter CD/MP3 mode. If a CD/MP3 is already present in the system, the disc will begin play. 3. CLK (Clock): Press CLK until SELECT HOUR/SELECT MINUTE is / ) to displayed. Press TUNE ( adjust the hours/minutes. Press CLK to display the time when the ignition is off. 4. TUNE: In radio mode, press to manually go up or down the radio frequency, or to access another CD. Also use in menu mode to select various settings. 5.
Entertainment Systems BASS: Press TUNE to decrease/increase the bass levels. TREB (treble): Press levels. TUNE to decrease/increase the treble BAL (Balance):Press left and right speakers. TUNE to adjust the audio between the FADE: Press rear speakers. TUNE to adjust the audio between the front and Next/previous directory: In MP3 mode, press the previous/next directory. TUNE to go to Flat file/directory mode: In MP3 mode, press Flat file mode or Directory mode.
Entertainment Systems 13. Memory presets: To set a station: Select frequency band AM/FM; tune to a station, press and hold a preset button until sound returns. To select a preset station, press the desired memory preset button. 14. MUTE: Press to mute the playing media. Press again to return to the playing media. 15. REW (rewind): Press to manually reverse a CD/MP3 track. 16. SEEK: In radio, CD and MP3 / to flat file mode, press access the previous/next strong station or track.
Entertainment Systems Tremor IV CD/MP3 satellite compatible audio system (if equipped) 1. EJ (CD eject): To eject an individual CD/MP3, press the eject control and select the correct slot number by pressing the corresponding memory preset. Press and hold to eject all loaded CD/MP3s. 2. CD: Press to enter CD/MP3 mode. If a CD/MP3 is already present in the system, the disc will begin play. 3. CLK (Clock): Press CLK until SELECT HOUR/SELECT MINUTE is / ) to displayed. Press TUNE ( adjust the hours/minutes.
Entertainment Systems 4. TUNE: In radio mode, press to manually go up or down the radio frequency, or to access another CD. Also use in menu mode to select various settings. In CATEGORY ALL, press / to scroll through the list of available Sirius channel Categories (Pop, Rock, News, etc.). Refer to Category Mode under Menu for further information. Satellite radio is available only with a valid SIRIUS subscription. Check with your authorized dealer for availability. 5.
Entertainment Systems BASS: Press TUNE to decrease/increase the bass levels. TREB (treble): Press levels. TUNE to decrease/increase the treble BAL (Balance):Press left and right speakers. TUNE to adjust the audio between the FADE: Press rear speakers. TUNE to adjust the audio between the front and Next/previous directory: In MP3 mode, press the previous/next directory. TUNE to go to Flat file/directory mode: In MP3 mode, press Flat file mode or Directory mode.
Entertainment Systems Satellite radio is available only with a valid SIRIUS subscription. Check with your authorized dealer for availability. 10. REPEAT: Press to repeat the current CD/MP3 track. The selection will repeat continuously until deactivated. Press REPEAT again to deactivate. 11. FF (fast forward): Press to manually advance in a CD/MP3 track. 12. Memory presets: To set a station: Select frequency band AM/FM; tune to a station, press and hold a preset button until sound returns.
Entertainment Systems In TEXT MODE, press SEEK to view the previous/additional display text. TUNE to select a category. In CATEGORY ALL, press SEEK to select a channel within In CATEGORY MODE, press that category. Satellite radio is available only with a valid SIRIUS subscription. Check with your authorized dealer for availability. 16. AM/FM: Press to select AM/FM1/FM2 frequency band. 17.
Entertainment Systems Auxiliary input jack (if equipped) Your vehicle may be equipped with an Auxiliary Input Jack (AIJ). The Auxiliary Input Jack provides a way to connect your portable music player to the in-vehicle audio system. This allows the audio from a portable music player to be played through the vehicle speakers with high fidelity. To achieve optimal performance, please observe the following instructions when attaching your portable music device to the audio system. Required equipment: 1.
Entertainment Systems Troubleshooting: 1. Do not connect the audio input jack to a line level output. Line level outputs are intended for connection to a home stereo and are not compatible with the AIJ. The AIJ will only work correctly with devices that have a headphone output with a volume control. 2. Do not set the portable music player’s volume level higher than is necessary to match the volume of the CD or FM radio in your audio system as this will cause distortion and will reduce sound quality.
Entertainment Systems CD/CD player care Do: • Handle discs by their edges only. Never touch the playing surface. • Inspect discs before playing. Clean only with an approved CD cleaner and wipe from the center out. Don’t: • Expose discs to direct sunlight or heat sources for extended periods of time. • Clean using a circular motion. CD units are designed to play commercially pressed 4.75 in (12 cm) audio compact discs only.
Entertainment Systems • Terrain: Hills, mountains, tall buildings, bridges, tunnels, freeway overpasses, parking garages, dense tree foliage and thunderstorms can interfere with your reception. • Station overload: When you pass a ground based broadcast repeating tower, a stronger signal may overtake a weaker one and result in an audio mute. Unlike AM/FM audible static, you will hear an audio mute when there is a satellite radio signal interference.
Entertainment Systems Radio Display ACQUIRING SAT FAULT INVALID CHNL UNSUBSCRIBED NO TEXT Condition Action Required Radio requires more No action required. than two seconds to This message should produce audio for the disappear shortly. selected channel. Internal module or If this message does system failure not clear within a short present. period of time, or with an ignition key cycle, your receiver may have a fault. See your authorized dealer for service. Channel no longer This previously available.
Entertainment Systems Radio Display NO TEXT NO TEXT NO SIGNAL UPDATING CALL SIRIUS 1–888–539–7474 Condition Song title information not available. Action Required Song title information not available at this time on this channel. The system is working properly. Category information Category information not available. not available at this time on this channel. The system is working properly.
Climate Controls HEATER ONLY SYSTEM (IF EQUIPPED) 1. Fan speed adjustment: Controls the volume of air circulated in the vehicle. 2. Temperature selection: Controls the temperature of the airflow in the vehicle. 3. Air flow selections: Controls the direction of the airflow in the vehicle. See the following for a brief description on each control. : Distributes outside air through the instrument panel vents. OFF: Outside air is shut out and the fan will not operate.
Climate Controls To aid in side window defogging/demisting in cold weather: 1. Select . 2. Adjust the temperature control to maintain comfort. 3. Set the fan speed to the highest setting. 4. Direct the outer instrument panel vents towards the side windows. To increase airflow to the outer instrument panel vents, close the vents located in the middle of the instrument panel. Do not place objects on top of the instrument panel as these objects may become projectiles in a collision or sudden stop.
Climate Controls Operating tips • To reduce fog build up on the windshield during humid weather, place position. the air flow selector in the • To reduce humidity build up inside the vehicle: do not drive with the air flow selector in the OFF position. • Under normal weather conditions, do not leave the air flow selector in MAX A/C or OFF when the vehicle is parked. This allows the vehicle to “breathe” using the outside air inlet vents.
Lights HEADLAMP CONTROL Turns the lamps off. Turns on the parking lamps, instrument panel lamps, license plate lamps and tail lamps. Turns the headlamps on. Foglamp control (if equipped) The foglamps can be turned on when the headlamp control is in or position and the the high beams are not turned on. Pull headlamp control towards you to turn foglamps on. The foglamp on the headlamp indicator light control and in the instrument cluster will illuminate.
Lights Flash to pass Pull toward you slightly to activate and release to deactivate. Daytime running lamps (DRL) (if equipped) The daytime running light system turns the headlamps on, with a reduced light output. To activate: • the ignition must be in the ON position and • the headlamp system is in the OFF position or parking lamp position. Always remember to turn on your headlamps at dusk or during inclement weather.
Lights AIMING THE HEADLAMPS The headlamps on your vehicle are properly aimed before leaving the assembly plant. If your vehicle is involved in an accident or if you have problems fixing the alignment of your headlamps, have them checked by a qualified service technician. Headlamp aim adjustment The headlamps are designed to be mechanically aimed, but can also be aimed visually by doing the following: 1. Park your vehicle on a level surface about 25 feet (7.6 meters) away from a vertical plain surface (3).
Lights 5. Locate the vertical adjuster for each headlamp. Adjust the aim by turning the adjuster control either clockwise (to adjust down) or counterclockwise (to adjust up). 6. In addition to the horizontal line marked in step 2, a pair of vertical lines (5) must be marked at the center line of the headlamps on the wall or screen. 7. On the wall or screen, locate the high intensity area of the beam pattern.
Lights INTERIOR LAMPS Courtesy/reading lamps (if equipped) The courtesy lamp lights when: • any door is opened. • the instrument panel dimmer switch is held up until the courtesy lamps come on. • the remote entry controls are pressed and the ignition is OFF. BULB REPLACEMENT Headlamp Condensation The headlamps are vented to equalize pressure. When moist air enters the headlamp(s) through the vents, there is a possibility that condensation can occur.
Lights Function Number of bulbs Trade number Rear license plate 2 194 lamps Backup lamps 2 3155 or 3156 (STX) Dome lamp 1 912 Map/dome-SuperCab 2 904 (if equipped) Map/dome-Regular 1 904 Cab (if equipped) All replacement bulbs are clear in color except where noted. To replace all instrument panel lights - see your authorized dealer. Replacing the interior bulbs Check the operation of all bulbs frequently. Replacing exterior bulbs Check the operation of all the bulbs frequently.
Lights 4. Remove the bulb retaining ring by rotating it counterclockwise and slide the ring off the plastic base. 5. Remove the old bulb by pulling it straight out of the lamp. Handle a halogen headlamp bulb carefully and keep out of children’s reach. Grasp the bulb only by its plastic base and do not touch the glass. The oil from your hand could cause the bulb to break the next time the headlamps are operated. Install the new bulb(s) in reverse order. Replacing front sidemarker bulbs 1.
Lights 3. Remove screw(s) from lamp assembly and disengage lamp assembly (it has a snap fit). 4. Rotate bulb socket counterclockwise and remove from lamp assembly. 5. Carefully pull bulb straight out of socket and push in the new bulb. 6. Install the bulb socket in lamp assembly by turning clockwise. Install the new bulb in reverse order.
Lights Replacing tail lamp/backup lamp bulbs 1. Make sure the headlamp switch is in the OFF position and the open the tailgate to expose the lamp assemblies. 2. Remove the four screws and the lamp assembly from vehicle. 3. Rotate bulb socket counterclockwise turn and remove from lamp assembly. 4. Carefully pull the bulb straight out of the socket Install the new bulb(s) in reverse order.
Lights Replacing foglamp bulbs (if equipped) 1. Make sure the headlamp switch is in the OFF position and remove the bulb socket from the foglamp by turning counterclockwise. 2. Disconnect the electrical connector. Install the new bulb in reverse order. Replacing high-mount brakelamp bulb 1. Make sure the headlamp switch is in the OFF position and remove the two screws and lamp assembly from vehicle. 2. Remove the bulb socket from lamp assembly by rotating it counterclockwise. 3.
Driver Controls MULTI-FUNCTION LEVER Windshield wiper: Rotate the end of the control away from you to increase the speed of the wipers (from desired interval to low or high speed position); rotate towards you to decrease the speed of the wipers. Windshield washer: Push the end of the stalk: • briefly: causes a single swipe of the wipers without washer fluid. • a quick push and hold: the wipers will swipe three times with washer fluid.
Driver Controls TILT STEERING WHEEL (IF EQUIPPED) To adjust the steering wheel: 1. Pull and hold the steering wheel release control toward you. 2. Move the steering wheel up or down until you find the desired location. 3. Release the steering wheel release control. This will lock the steering wheel in position. Never adjust the steering wheel when the vehicle is moving. CENTER CONSOLE (IF EQUIPPED) Your vehicle may be equipped with a variety of console features.
Driver Controls The auxiliary power points are located on the instrument panel. Do not use the power point for operating the cigarette lighter element (if equipped). To prevent the fuse from being blown, do not use the power point(s) over the vehicle capacity of 12 VDC/180W. Refer to Passenger Compartment Fuse Panel in the Roadside Emergencies chapter for fuse ratings in your vehicle.
Driver Controls One touch down Allows the driver’s window to open fully without holding the control down. Press completely down on AUTO and release quickly. Press again to stop. EXTERIOR MIRRORS Power side view mirrors (if equipped) To adjust your mirrors: to adjust the left 1. Select mirror or to adjust the right mirror. 2. Move the control in the direction you wish to tilt the mirror. 3. Return to the center position to lock mirrors in place.
Driver Controls Setting speed control The controls for using your speed control are located on the steering wheel for your convenience. 1. Press the ON control and release it. 2. Accelerate to the desired speed. 3. Press the SET + control and release it. 4. Take your foot off the accelerator pedal. on the 5. The indicator light instrument cluster will turn on. Note: • Vehicle speed may vary momentarily when driving up and down a steep hill.
Driver Controls Resuming a set speed Press the RES (resume) control and release it. This will automatically return the vehicle to the previously set speed. The RES control will not work if the vehicle speed is not faster than 30 mph (48 km/h). Increasing speed while using speed control There are three ways to set a higher speed: • Press and hold the SET + control until you get to the desired speed, then release the control. • Press and release the SET + control to operate the Tap-Up function.
Driver Controls Turning off speed control There are two ways to turn off the speed control: • Press the speed control OFF control. • Turn OFF the ignition. Note: When you turn off the speed control or the ignition, your speed control set speed memory is erased. CARGO AREA FEATURES Cargo area shade (if equipped) Your vehicle may be equipped with notches in the side trim panels that are used for a cargo area shade. See your authorized dealer for more information.
Driver Controls 4. Evenly push down on the bed extender and push the lever in on each side locking it in place. To stow the bed extender, follow steps one through four in reverse order. The bed extender may be used to secure a load of up to 100 lb. (46 kg) on the tailgate. The bed extender should always be kept in the stowed position with the tailgate closed when not in use.
Locks and Security KEYS The key operates all locks on your vehicle. You should always carry a second key with you in a safe place in case you require it in an emergency. If your vehicle is equipped with the SecuriLock娂 Passive Anti-theft system, your keys are coded to your vehicle; using a non-coded key will not permit your vehicle to start. If you lose your dealer supplied keys, replacement keys are available through your authorized dealer.
Locks and Security Your vehicle is equipped with a remote entry system which allows you to: • unlock the vehicle doors without a key. • lock all the vehicle doors without a key. • activate the personal alarm. If there are problems with the remote entry system, make sure to take ALL remote entry transmitters with you to your authorized dealer in order to aid in troubleshooting the problem. Unlocking the doors 1. Press and release to unlock the driver’s door. Note: The interior lamps will illuminate. 2.
Locks and Security Replacing the battery The remote entry transmitter uses one coin type three-volt lithium battery CR2032 or equivalent. To replace the battery: 1. Twist a thin coin between the two halves of the remote entry transmitter near the key ring. DO NOT TAKE THE RUBBER COVER AND CIRCUIT BOARD OFF THE FRONT HOUSING OF THE REMOTE ENTRY TRANSMITTER. 2. Do not wipe off any grease on the battery terminals on the back surface of the circuit board. 3. Remove the old battery.
Locks and Security Replacing lost remote entry transmitters If you would like to have your remote entry transmitter reprogrammed because you lost one, or would like to buy additional remote entry transmitters, you can either reprogram them yourself, or take all remote entry transmitters to your authorized dealer for reprogramming. How to reprogram your remote entry transmitters You must have all remote entry transmitters (maximum of four) available before beginning this procedure.
Locks and Security Illuminated entry The interior lamps illuminate when the remote entry system is used to unlock the door(s) or sound the personal alarm. The illuminated entry system will turn off the interior lights if: • the ignition switch is turned to the ON position, or • the remote transmitter lock control is pressed, or • after 25 seconds of illumination. The inside lights will not turn off if: • they have been turned on with the dimmer control, or • any door is open.
Locks and Security Anti-theft indicator The anti-theft indicator is located in the instrument cluster. Vehicles equipped with the SecuriLock娂 Passive Anti-theft system behave as follows: • When the ignition is in the 1(OFF/LOCK) position, the indicator will flash once every 2 seconds for a total of 10 seconds to indicate the SecuriLock娂 system is functioning as a theft deterrent.
Locks and Security • If no previously programmed coded keys are available, you must take your vehicle to your authorized dealer to have the spare key(s) programmed. 1. Insert a previously programmed coded key into the ignition. 4 2. Turn the ignition from the 3 3 (OFF) position to the 4 (ON) 5 position. Keep the ignition in the 4 (ON) position for at least one 2 second, but no more than 10 seconds. 1 3. Turn the ignition to the 3 (OFF) position, and remove the coded key from the ignition. 4.
Seating and Safety Restraints SEATING Notes: Reclining the seatback can cause an occupant to slide under the seat’s safety belt, resulting in severe personal injuries in the event of a collision. Do not pile cargo higher than the seatbacks to reduce the risk of injury in a collision or sudden stop. Before returning the seatback to its original position, make sure that cargo or any objects are not trapped behind the seatback.
Seating and Safety Restraints Lift the release bar to move seat forward or backward. Ensure that the seat is locked into place. Pull lever located at the side of the seat cushion up to adjust seatback. 60/40 seat (if equipped) To gain access to the storage compartment in your armrest (if equipped), lift the latch to open lid. The 60/40 seat cupholder (if equipped) is detachable for cleaning. • Firmly grasp the bottom of the cup holder and pull up.
Seating and Safety Restraints Using the manual lumbar support (if equipped) Turn the lumbar support control clockwise to increase firmness. Turn the lumbar support control counterclockwise to increase softness. Passenger side rear access Pull up on the recliner handle. The seat will lean forward. Lift the release bar to move the seat forward to access the rear area of the cab. To return seat to original position, slide the seat bottom back, then push the seatback up to lock it in place.
Seating and Safety Restraints Center facing jump seat (4 door SuperCab) (if equipped) To open, pull seat assembly down, then raise seatback. To stow the seat, fold seat back down and raise seat assembly to the fully upright position. Do not install a child seat in the center facing jump seats as there are no child restraints recommended for use in this seating position. Booster seats must be installed only in seating positions equipped with a combination lap/shoulder belt.
Seating and Safety Restraints • Restraint system warning light and back-up tone. • The electrical wiring for the airbags, crash sensor(s), safety belt pretensioners, front safety belt usage sensors, driver seat position sensor, and indicator lights. How does the Personal Safety System姟 work? The Personal Safety System娂 can adapt the deployment strategy of your vehicle’s safety devices according to crash severity and occupant classification and conditions.
Seating and Safety Restraints Front passenger sensing system For airbags to do their job they must inflate with great force, and this force can pose a potentially deadly risk to occupants that are very close to the airbag when it begins to inflate. For some occupants, like infants in rear-facing child seats, this occurs because they are initially sitting very close to the airbag.
Seating and Safety Restraints Front outboard safety belt pretensioners The safety belt pretensioners at the front outboard seating positions are designed to tighten the safety belts firmly against the occupant’s body during frontal collisions, and in side collisions and rollovers when the vehicle is equipped with the Safety Canopy娂 system. This helps increase the effectiveness of the safety belts.
Seating and Safety Restraints Safety restraints precautions Always drive and ride with your seatback upright and the lap belt snug and low across the hips. To reduce the risk of injury, make sure children sit where they can be properly restrained. Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from injury in a collision.
Seating and Safety Restraints Combination lap and shoulder belts 1. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) until you hear a snap and feel it latch. Make sure the tongue is securely fastened in the buckle. 2. To unfasten, push the release button and remove the tongue from the buckle. Lap belts Adjusting the front center seat and rear center facing jump seat lap belts (if equipped) The lap belt does not adjust automatically.
Seating and Safety Restraints Shorten and fasten the belt when not in use. For the rear jump seat, shorten and fold the belt into the seat when not in use. Energy Management Feature • This vehicle has a safety belt system with an energy management feature at the front outboard seating positions to help further reduce the risk of injury in the event of a head-on collision. • This energy management system has a retractor assembly that is designed to pay out webbing in a controlled manner.
Seating and Safety Restraints How to use the automatic locking mode • Buckle the combination lap and shoulder belt. • Grasp the shoulder portion and pull downward until the entire belt is pulled out. • Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the automatic locking mode.
Seating and Safety Restraints BELT AND RETRACTOR ASSEMBLY MUST BE REPLACED if the safety belt assembly “automatic locking retractor” feature or any other safety belt function is not operating properly when checked authorized dealer. Failure to replace the Belt and Retractor assembly could increase the risk of injury in collisions. Safety belt pretensioner Your vehicle is equipped with safety belt pretensioners at the driver and front outboard passenger seating positions.
Seating and Safety Restraints • 2–door SuperCab To lower the shoulder belt height, push the button and slide the height adjuster down. To raise the height of the shoulder belt, push the button and slide the height adjuster up. Pull down on the height adjuster to make sure it is locked in place. Position the safety belt height adjusters so that the belt rests across the middle of your shoulder.
Seating and Safety Restraints equipped), child safety seat tether anchors, and attaching hardware, should be inspected after a collision. Ford Motor Company recommends that all safety belt assemblies in use in vehicles involved in a collision be replaced. However, if the collision was minor and an authorized dealer finds that the belts do not show damage and continue to operate properly, they do not need to be replaced.
Seating and Safety Restraints BeltMinder姞 The BeltMinder威 feature is a supplemental warning to the safety belt warning function. This feature provides additional reminders by intermittently sounding a chime and illuminating the safety belt warning light in the instrument cluster when the driver’s and front passenger’s safety belt is unbuckled.
Seating and Safety Restraints If... The driver’s or front passenger’s safety belt becomes unbuckled for approximately 1 minute while the vehicle is traveling at least 3 mph (5 km/h) and more than 1-2 minutes have elapsed since the ignition switch has been turned to ON... Then... The BeltMinder威 feature is activated the safety belt warning light illuminates and the warning chime sounds for 6 seconds every 30 seconds, repeating for approximately 5 minutes or until the safety belts are buckled.
Seating and Safety Restraints Reasons given... “Traffic is light” “Belts wrinkle my clothes” “The people I’m with don’t wear belts” “I have an airbag” “I’d rather be thrown clear” Consider... Nearly 1 of 2 deaths occur in single-vehicle crashes, many when no other vehicles are around. Possibly, but a serious crash can do much more than wrinkle your clothes, particularly if you are unbelted. Set the example, teen deaths occur 4 times more often in vehicles with TWO or MORE people.
Seating and Safety Restraints Read Steps 1 - 4 thoroughly before proceeding with the deactivation/activation programming procedure. Note: The driver and front passenger BeltMinder威 features must be disabled/enabled separately. Both cannot be disable/enabled during the same key cycle.
Seating and Safety Restraints • This will enable the BeltMinder威 feature for that seating position if it is currently disabled. As confirmation, the safety belt warning light will flash 4 times per second for 3 seconds, followed by 3 seconds with the light off, then followed by the safety belt warning light flashing 4 times per second for 3 seconds again.
Seating and Safety Restraints Important supplemental restraint system (SRS) precautions The supplemental restraint system is designed to work with the safety belt to help protect the driver and right front passenger from certain upper body injuries. Airbags DO NOT inflate slowly or gently and the risk of injury from a deploying airbag is greatest close to the trim covering the airbag module. Rear facing child seats should NEVER be placed in front of an active airbag.
Seating and Safety Restraints Steps you can take to properly position yourself away from the airbag: • Move your seat to the rear as far as you can while still reaching the pedals comfortably. • Recline the seat slightly (one or two degrees) from the upright position. Do not put anything on or over the airbag module. Placing objects on or over the airbag inflation area may cause those objects to be propelled by the airbag into your face and torso causing serious injury.
Seating and Safety Restraints Children and airbags For additional important safety information, read all information on safety restraints in this guide. Do not install a child seat in a center facing jump seat. Airbags can kill or injure a child in a child seat. NEVER place a rear-facing child seat in front of an active airbag. If you must use a forward-facing child seat in the front seat, move the seat all the way back.
Seating and Safety Restraints The airbags inflate and deflate rapidly upon activation. After airbag deployment, it is normal to notice a smoke-like, powdery residue or smell the burnt propellant. This may consist of cornstarch, talcum powder (to lubricate the bag) or sodium compounds (e.g., baking soda) that result from the combustion process that inflates the airbag. Small amounts of sodium hydroxide may be present which may irritate the skin and eyes, but none of the residue is toxic.
Seating and Safety Restraints A difficulty with the system is indicated by one or more of the following: • The readiness lights will either flash or stay lit. • The readiness lights will not illuminate immediately after ignition is turned on. • A series of five beeps will be heard. The tone pattern will repeat periodically until the problem and/or light are repaired. If any of these things happen, even intermittently, have the SRS serviced at an authorized dealer immediately.
Seating and Safety Restraints Even with Advanced Restraints Systems, children 12 and under should be properly restrained in the back seat (if equipped). When the front passenger seat is occupied and the sensing system has turned off the passenger’s frontal air bag, the ⬙passenger air bag off⬙ or ⬙pass air bag off⬙ indicator will light and stay lit to remind you that the front passenger frontal air bag is off.
Seating and Safety Restraints Occupant Pass Airbag Off Indicator Lamp Unlit Lit Passenger Airbag Empty seat Disabled Disabled Small child in child safety seat or booster Small child with safety Lit Disabled belt buckled or unbuckled Adult Unlit Enabled After all occupants have adjusted their seats and put on safety belts, it’s very important that they continue to sit upright, with their back against the seatback, with their feet comfortably extended on the floor while the vehicle is still in motion.
Seating and Safety Restraints The front passenger sensing system may detect small or medium objects placed on the seat cushion. For most objects that are in the front passenger seat, the passenger airbag will be disabled. Even though the passenger airbag is disabled, the ⬙pass airbag off⬙ light may or may not be illuminated according to the table below. Objects Pass Airbag Off Indicator Lamp Unlit Small (i.e. 3 ring binder, small purse, bottled water) Medium (i.e.
Seating and Safety Restraints Do not install a child seat in a center facing jump seat. Children and safety belts If the child is the proper size, restrain the child in a safety seat. Children who are too large for child safety seats (as specified by your child safety seat manufacturer) should always wear safety belts. Follow all the important safety restraint and airbag precautions that apply to adult passengers in your vehicle.
Seating and Safety Restraints Booster seats should be used until you can answer YES to ALL of these questions: • Can the child sit all the way back against the vehicle seat back with knees bent comfortably at the edge of the seat without slouching? • Does the lap belt rest low across the hips? • Is the shoulder belt centered on the shoulder and chest? • Can the child stay seated like this for the whole trip? Types of booster seats There are two types of belt-positioning booster seats: • Those that are back
Seating and Safety Restraints Children and booster seats vary widely in size and shape. Choose a booster that keeps the lap belt low and snug across the hips, never up across the stomach, and lets you adjust the shoulder belt to cross the chest and rest snugly near the center of the shoulder. The drawings below compare the ideal fit (center) to a shoulder belt uncomfortably close to the neck and a shoulder belt that could slip off the shoulder.
Seating and Safety Restraints Never use pillows, books, or towels to boost a child. They can slide around and increase the likelihood of injury or death in a collision. SAFETY SEATS FOR CHILDREN Child and infant or child safety seats Use a safety seat that is recommended for the size and weight of the child. Carefully follow all of the manufacturer’s instructions with the safety seat you put in your vehicle.
Seating and Safety Restraints anchor. For more information on top tether straps, refer to Attaching child safety seats with tether straps. in this chapter. Carefully follow all of the manufacturer’s instructions included with the safety seat you put in your vehicle. If you do not install and use the safety seat properly, the child may be injured in a sudden stop or collision. Installing child safety seats with combination lap and shoulder belts 1.
Seating and Safety Restraints 3. While holding the shoulder and lap belt portions together, route the tongue through the child seat according to the child seat manufacturer’s instructions. Be sure the belt webbing is not twisted. 4. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) for that seating position until you hear and feel the latch engage. Make sure the tongue is latched securely by pulling on it. 5.
Seating and Safety Restraints 7. Pull the lap belt portion across the child seat toward the buckle and pull up on the shoulder belt while pushing down with knee on the child seat. 8. Allow the safety belt to retract to remove any slack in the belt. 9. Before placing the child in the seat, forcibly tilt the seat forward and back to make sure the seat is securely held in place. To check this, grab the seat at the belt path and attempt to move it side to side and forward.
Seating and Safety Restraints The tether strap anchors in your vehicle are in the following positions (shown from top view): • Bucket seats • 60/40 seats Attach the tether strap only to the appropriate tether anchor as shown. The tether strap may not work properly if attached somewhere other than the correct tether anchor. 1. Position the child safety seat on the front seat cushion. 2. Route the child safety seat tether strap over the back of the seat.
Seating and Safety Restraints 3. Locate the correct anchor for the selected seating position. The tether anchor is located on the rear lower portion of the passenger seat. 4. Clip the tether strap to the anchor.
Seating and Safety Restraints Center seating location When installing a child safety seat in the front center position, route the tether strap over the center arm rest and clip it to the center anchor. If the tether strap is clipped incorrectly, the child safety seat may not be retained properly in the event of a collision. 5. Install the child safety seat tightly using the safety belt. Follow the instructions in this chapter. 6.
Tires, Wheels and Loading NOTICE TO UTILITY VEHICLE AND TRUCK OWNERS Utility vehicles and trucks handle differently than passenger cars in the various driving conditions that are encountered on streets, highways and off-road. Utility vehicles and trucks are not designed for cornering at speeds as high as passenger cars any more than low-slung sports cars are designed to perform satisfactorily under off-road conditions. Utility vehicles have a significantly higher rollover rate than other types of vehicles.
Tires, Wheels and Loading Power is supplied to all four wheels through a transfer case or power transfer unit. 4WD vehicles allow you to select different drive modes as necessary. Information on transfer case operation and shifting procedures can be found in the Driving chapter. Information on transfer case maintenance can be found in the Maintenance and Specifications chapter. You should become thoroughly familiar with this information before you operate your vehicle.
Tires, Wheels and Loading • Narrower — to provide greater maneuverability in tight spaces, particularly in off-road use. As a result of the above dimensional differences, SUV’s and trucks often will have a higher center of gravity and a greater difference in center of gravity between the loaded and unloaded condition. These differences that make your vehicle so versatile also make it handle differently than an ordinary passenger car.
Tires, Wheels and Loading Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half (1 1/2) times as well on the government course as a tire graded 100.
Tires, Wheels and Loading Glossary of tire terminology • Tire label: A label showing the OE (Original Equipment) tire sizes, recommended inflation pressure and the maximum weight the vehicle can carry. • Tire Identification Number (TIN): A number on the sidewall of each tire providing information about the tire brand and manufacturing plant, tire size and date of manufacture. Also referred to as DOT code. • Inflation pressure: A measure of the amount of air in a tire.
Tires, Wheels and Loading Every day before you drive, check your tires. If one looks lower than the others, use a tire gauge to check pressure of all tires and adjust if required. At least once a month and before long trips, inspect each tire and check the tire pressure with a tire gauge (including spare, if equipped). Inflate all tires to the inflation pressure recommended by Ford Motor Company.
Tires, Wheels and Loading drop of 1 psi (7 kPa) in inflation pressure. Check your tire pressures frequently and adjust them to the proper pressure which can be found on the Safety Compliance Certification Label or Tire Label. To check the pressure in your tire(s): 1. Make sure the tires are cool, meaning they are not hot from driving even a mile. If you are checking tire pressure when the tire is hot, (i.e. driven more than 1 mile [1.6 km]), never “bleed” or reduce air pressure.
Tires, Wheels and Loading tread grooves. Check for holes or cuts that may permit air leakage from the tire and make necessary repairs. Also inspect the tire sidewalls for cracking, cuts, bruises and other signs of damage or excessive wear. If internal damage to the tire is suspected, have the tire demounted and inspected in case it needs to be repaired or replaced. For your safety, tires that are damaged or show signs of excessive wear should not be used because they are more likely to blow out or fail.
Tires, Wheels and Loading U.S. DOT Tire Identification Number (TIN) Both U.S. and Canada Federal regulations require tire manufacturers to place standardized information on the sidewall of all tires. This information identifies and describes the fundamental characteristics of the tire and also provides a U.S. DOT Tire Identification Number for safety standard certification and in case of a recall. This begins with the letters “DOT” and indicates that the tire meets all federal standards.
Tires, Wheels and Loading When mounting replacement tires and wheels, you should not exceed the maximum pressure indicated on the sidewall of the tire to set the beads without additional precautions listed below. If the beads do not seat at the maximum pressure indicated, re-lubricate and try again. When inflating the tire for mounting pressures up to 20 psi greater than the maximum pressure on the tire sidewall, the following precautions must be taken to protect the person mounting the tire: 1.
Tires, Wheels and Loading If your vehicle is stuck in snow, mud, sand, etc., do not rapidly spin the tires; spinning the tires can tear the tire and cause an explosion. A tire can explode in as little as three to five seconds. Do not spin the wheels at over 35 mph (56 km/h). The tires may fail and injure a passenger or bystander. Highway hazards No matter how carefully you drive there’s always the possibility that you may eventually have a flat tire on the highway.
Tires, Wheels and Loading • Rear Wheel Drive (RWD) vehicles/Four Wheel Drive (4WD)/ All Wheel Drive (AWD) vehicles (front tires at top of diagram) Sometimes irregular tire wear can be corrected by rotating the tires. Note: If your tires show uneven wear ask an authorized dealer to check for and correct any wheel misalignment, tire imbalance or mechanical problem involved before tire rotation. Note: Your vehicle may be equipped with a dissimilar spare tire/wheel.
Tires, Wheels and Loading Information on “P” type tires P215/65R15 95H is an example of a tire size, load index and speed rating. The definitions of these items are listed below. (Note that the tire size, load index and speed rating for your vehicle may be different from this example.) 1. P: Indicates a tire, designated by the Tire and Rim Association (T&RA), that may be used for service on cars, SUVs, minivans and light trucks.
Tires, Wheels and Loading Note: You may not find this information on all tires because it is not required by federal law. Letter rating Speed rating - mph (km/h) M 81 mph (130 km/h) N 87 mph (140 km/h) Q 99 mph (159 km/h) R 106 mph (171 km/h) S 112 mph (180 km/h) T 118 mph (190 km/h) U 124 mph (200 km/h) H 130 mph (210 km/h) V 149 mph (240 km/h) W 168 mph (270 km/h) Y 186 mph (299 km/h) Note: For tires with a maximum speed capability over 149 mph (240 km/h), tire manufacturers sometimes use the letters ZR.
Tires, Wheels and Loading 12. Treadwear, Traction and Temperature Grades • Treadwear: The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half (11⁄2) times as well on the government course as a tire graded 100. • Traction: The traction grades, from highest to lowest are AA, A, B, and C.
Tires, Wheels and Loading Additional information contained on the tire sidewall for “LT” type tires “LT” type tires have some additional information beyond those of “P” type tires; these differences are described below: 1. LT: Indicates a tire, designated by the Tire and Rim Association (T&RA), that is intended for service on light trucks. 2. Load Range/Load Inflation Limits: Indicates the tire’s load-carrying capabilities and its inflation limits. 3. Maximum Load Dual lb.
Tires, Wheels and Loading Information on “T” type tires “T” type tires have some additional information beyond those of “P” type tires; these differences are described below: T145/80D16 is an example of a tire size. Note: The temporary tire size for your vehicle may be different from this example. 1. T: Indicates a type of tire, designated by the Tire and Rim Association (T&RA), that is intended for temporary service on cars, SUVs, minivans and light trucks. 2.
Tires, Wheels and Loading TIRE PRESSURE MONITORING SYSTEM (TPMS) Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label. (If your vehicle has tires of a different size than the size indicated on the vehicle placard or tire inflation pressure label, you should determine the proper tire inflation pressure for those tires.
Tires, Wheels and Loading Changing tires with TPMS Each road tire is equipped with a tire pressure sensor fastened to the inside rim of the wheel. The pressure sensor is covered by the tire and is not visible unless the tire is removed. The pressure sensor is located opposite (180 degrees) from the valve stem. Care must be taken when changing the tire to avoid damaging the sensor. It is recommended that you always have your tires serviced by an authorized dealer.
Tires, Wheels and Loading no longer capable of functioning as intended. Please refer to the following chart for information concerning your Tire Pressure Monitoring System: Low Tire Pressure Possible cause Customer Action Required Warning Light Solid Warning Light Tire(s) 1. Check your tire pressure to under-inflated ensure tires are properly inflated; refer to Inflating your tires in this chapter. 2.
Tires, Wheels and Loading Low Tire Pressure Possible cause Customer Action Required Warning Light Flashing Warning Spare tire in use Your temporary spare tire is in Light use. Repair the damaged road wheel and re-mount it on the vehicle to restore system functionality. For a description of how the system functions under these conditions, refer to When your temporary spare tire is installed in this section.
Tires, Wheels and Loading any tire is under-inflated, carefully drive the vehicle to the nearest location where air can be added to the tires. Inflate all the tires to the recommended inflation pressure. SNOW TIRES AND CHAINS Driving too fast for conditions creates the possibility of loss of vehicle control. Driving at very high speeds for extended periods of time may result in damage to vehicle components. Snow tires must be the same size and grade as the tires you currently have on your vehicle.
Tires, Wheels and Loading Base Curb Weight – is the weight of the vehicle including a full tank of fuel and all standard equipment. It does not include passengers, cargo, or optional equipment. Vehicle Curb Weight – is the weight of your new vehicle when you picked it up from your authorized dealer plus any aftermarket equipment. Payload – is the combined weight of cargo and passengers that the vehicle is carrying.
Tires, Wheels and Loading Example only: Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. When towing, trailer tongue load or king pin weight is also part of cargo weight. GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) – including vehicle curb weight and all payload.
Tires, Wheels and Loading GAWR (Gross Axle Weight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance Certification Label located on the B-Pillar or the edge of the driver’s door. The total load on each axle must never exceed its GAWR. Note: For trailer towing information refer to Trailer towing found in this chapter or the RV and Trailer Towing Guide provided by your authorized dealer.
Tires, Wheels and Loading GCW (Gross Combined Weight) – is the weight of the loaded vehicle (GVW) plus the weight of the fully loaded trailer. GCWR (Gross Combined Weight Rating) – is the maximum allowable weight of the vehicle and the loaded trailer – including all cargo and passengers – that the vehicle can handle without risking damage. (Important: The towing vehicle’s braking system is rated for operation at GVWR, not at GCWR.
Tires, Wheels and Loading Exceeding any vehicle weight rating limitation could result in serious damage to the vehicle and/or personal injury. Steps for determining the correct load limit: 1. Locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or XXX lbs.” on your vehicle’s placard. 2. Determine the combined weight of the driver and passengers that will be riding in your vehicle. 3. Subtract the combined weight of the driver and passengers from XXX kg or XXX lbs. 4.
Tires, Wheels and Loading transport the cement to your home? If you and your friend each weigh 220 lb. (99 kg), the calculation would be: 1400 - (2 x 220) (12 x 100) = 1400 - 440 - 1200 = - 240 lb. No, you do not have enough cargo capacity to carry that much weight. In metric units, the calculation would be: 635 kg - (2 x 99 kg) - (12 x 45 kg) = 635 - 198 540 = -103 kg. You will need to reduce the load weight by at least 240 lb. (104 kg). If you remove 3-100 lb.
Tires, Wheels and Loading Engine 2.3L 3.0L* 3.0L* Edge 4x2 w/manual transmission Rear axle Maximum Maximum ratio GCWR - lb. trailer (kg) weight - lb. (kg) Regular Cab w/6’ box All 4800 (2177) 1580 (716) All All 2.3L All 3.0L* All 2.3L All 6000 (2722) 6000 (2722) 2640 (1198) 2500 (1134) Regular Cab w/7’ box 4800 (2177) 1520 (689) 6000 (2722) SuperCab 4800 (2177) 2580 (1170) 1400 (635) Maximum frontal area of trailer ft2 (m2) Equal to frontal area of vehicle 50 (4.64) 50 (4.
Tires, Wheels and Loading 4x2 w/manual transmission Engine Rear axle Maximum Maximum Maximum ratio GCWR - lb. trailer frontal area (kg) weight - lb. of trailer (kg) ft2 (m2) Maximum trailer weight is shown. The combined weight of the completed towing vehicle (including hitch, passengers and cargo) and the loaded trailer must not exceed the Gross Combined Weight Rating (GCWR). The Ranger is capable of pulling the maximum trailer weight(s) as specified above.
Tires, Wheels and Loading 4x4 w/manual transmission Engine Rear axle Maximum Maximum Maximum ratio GCWR - lb. trailer frontal area (kg) weight - lb. of trailer (kg) ft2 (m2) *When towing on roads with steep grades or moderate but long sustained grades (5 miles [8 km] or more), or when ambient temperatures exceed 100°F (37°C), vehicle speed should not exceed 45 mph (72 km/h) in both cases. For definition of terms used in this table, see Vehicle loading earlier in this chapter.
Tires, Wheels and Loading Engine 3.0L* 4.0L 2.3L 4x2 w/automatic transmission Rear axle Maximum Maximum ratio GCWR - lb. trailer (kg) weight - lb. (kg) All 6000 (2722) 2540 (1152) All 9500 (4309) 6000 (2722) SuperCab All 5500 (2495) 2100 (953) Maximum frontal area of trailer ft2 (m2) 50 (4.64) 50 (4.64) Equal to frontal area of vehicle 50 (4.64) 50 (4.64) 3.0L* All 6000 (2722) 2420 (1098) 3.0L* All 6000 (2722) 2280 (1034) Edge 4.0L All 9500 (4309) 5860 (2658) 50 (4.64) 4.
Tires, Wheels and Loading Engine 3.0L* 4.0L 3.0L* 4.0L 4x4 w/automatic transmission Rear axle Maximum Maximum ratio GCWR - lb. trailer (kg) weight - lb. (kg) Regular Cab w/6’ box All 6000 (2722) 2300 (1043) All 9500 (4309) 5720 (2594) Regular Cab w/7’ box All 6000 (2722) 2220 (1007) All 9500 (4309) 5640 (2558) SuperCab All 9500 (4309) 5560 (2522) Maximum frontal area of trailer ft2 (m2) 50 (4.64) 50 (4.64) 50 (4.64) 50 (4.64) 4.0L 50 (4.64) (without FX4 package) 4.0L All 9500 (4309) 5220 (2368 ) 50 (4.
Tires, Wheels and Loading Do not exceed the GVWR or the GAWR specified on the certification label. Towing trailers beyond the maximum recommended gross trailer weight exceeds the limit of the vehicle and could result in engine damage, transmission damage, structural damage, loss of vehicle control, vehicle rollover and personal injury. Preparing to tow Use the proper equipment for towing a trailer and make sure it is properly attached to your vehicle.
Tires, Wheels and Loading Trailer brakes Electric brakes and manual, automatic or surge-type trailer brakes are safe if installed properly and adjusted to the manufacturer’s specifications. The trailer brakes must meet local and Federal regulations. Do not connect a trailer’s hydraulic brake system directly to your vehicle’s brake system. Your vehicle may not have enough braking power and your chances of having a collision greatly increase.
Tires, Wheels and Loading Trailer tow connector The trailer tow connector is located under the rear bumper, on the driver’s side of the vehicle. 1 2 4 3 Refer to the following chart for information regarding the factory-equipped trailer tow connector: Trailer tow connector Color Function 1. Dark Green Trailer right-hand turn signal 2. Yellow Trailer left-hand turn signal 3. Tan/White Tail lamp 4.
Tires, Wheels and Loading • Consult your local motor vehicle speed regulations for towing a trailer. • To eliminate excessive shifting, use a lower gear. This will also assist in transmission cooling. (For additional information, refer to the Driving with a 5–speed automatic transmission section in the Driving chapter.) • Under extreme conditions with large frontal trailers, high outside temperatures and highway speeds, the coolant gauge may indicate higher than normal coolant temperatures.
Tires, Wheels and Loading • Vehicles with trailers should not be parked on a grade. If you must park on a grade, place wheel chocks under the trailer’s wheels. Launching or retrieving a boat Disconnect the wiring to the trailer before backing the trailer into the water. Reconnect the wiring to the trailer after the trailer is removed from the water. When backing down a ramp during boat launching or retrieval: • do not allow the static water level to rise above the bottom edge of the rear bumper.
Tires, Wheels and Loading For 4x4 vehicles with a manual transmission, it is recommended that a Neutral Tow Kit be purchased and installed by an authorized dealer if the vehicle is towed frequently. In addition, it is recommended that you follow the instructions provided by the aftermarket manufacturer of the towing apparatus if one has been installed.
Driving STARTING Positions of the ignition 1. ACCESSORY, allows the electrical accessories such as the radio to operate while the engine is not running. 2. LOCK, locks the steering wheel, automatic transmission gearshift lever and allows key removal. For vehicles equipped with a manual transmission, you must depress the ignition release lever to release the key. 3 4 5 2 1 3. OFF, shuts off the engine and all accessories without locking the steering wheel.
Driving Extended idling at high engine speeds can produce very high temperatures in the engine and exhaust system, creating the risk of fire or other damage. Do not park, idle, or drive your vehicle in dry grass or other dry ground cover. The emission system heats up the engine compartment and exhaust system, which can start a fire. Do not start your vehicle in a closed garage or in other enclosed areas. Exhaust fumes can be toxic. Always open the garage door before you start the engine.
Driving If starting a vehicle with an automatic transmission: • Make sure the parking brake is set. • Make sure the gearshift is in P (Park). If starting a vehicle with a manual transmission: 1. Make sure the parking brake is set. 2. Push the clutch pedal to the floor. • Turn the key to 4 (ON) without turning the key to 5 (START). 4 3 5 2 1 Some warning lights will briefly illuminate. See Warning lights and chimes in the Instrument Cluster chapter for more information regarding the warning lights.
Driving Starting the engine 1. Turn the key to 4 (ON) without turning the key to 5 (START). If there is difficulty in turning the key, rotate the steering wheel until the key turns freely. 2. Turn the key to 5 (START), then release the key as soon as the engine starts. Excessive cranking could damage the starter. 4 3 5 2 1 Note: If the engine does not start within five seconds on the first try, turn the key to OFF, wait 10 seconds and try again.
Driving To reduce the risk of electrical shock, do not use your heater with ungrounded electrical systems or two-pronged (cheater) adapters. BRAKES Occasional brake noise is normal. If a metal-to-metal, continuous grinding or continuous squeal sound is present, the brake linings may be worn-out and should be inspected by an authorized dealer. If the vehicle has continuous vibration or shudder in the steering wheel while braking, the vehicle should be inspected by an authorized dealer.
Driving Even when the ABS is disabled, normal braking is still effective. (If your BRAKE warning lamp illuminates with the parking brake released, have your brake system serviced immediately.) Parking brake To set the parking brake (1), press the parking brake pedal down until the pedal stops. ! P BRAKE The BRAKE warning lamp will illuminate and will remain illuminated until the parking brake is released. ! P BRAKE To release, pull the lever (2).
Driving • Do not fill the power steering fluid reservoir above the MAX mark on the reservoir, as this may result in leaks from the reservoir. If the power steering system breaks down (or if the engine is turned off), you can steer the vehicle manually, but it takes more effort.
Driving Loaded vehicles, with a higher center of gravity, may handle differently than unloaded vehicles. Do not overload your vehicle and use extra precautions, such as driving at slower speeds, avoiding abrupt steering changes and allowing for increased stopping distance, when driving a heavily loaded vehicle. Over loading or loading the vehicle improperly can deteriorate handling capability and contribute to loss of vehicle control and vehicle rollover.
Driving If the parking brake is fully released, but the brake warning lamp remains illuminated, the brakes may not be working properly. See your authorized dealer. Driving with a 5–speed automatic transmission (if equipped) This vehicle is equipped with an adaptive Transmission Shift Strategy. Adaptive Shift Strategy offers the optimal transmission operation and shift quality.
Driving N (Neutral) With the gearshift lever in N (Neutral), the vehicle can be started and is free to roll. Hold the brake pedal down while in this position. D (Drive) with Overdrive The normal driving position for the best fuel economy. Transmission operates in gears one through five. D (Drive) without Overdrive D (Drive) with Overdrive can be deactivated by pressing the O/D ON/OFF transmission control switch on the end of the gearshift lever. • This position allows for all forward gears except overdrive.
Driving MANUAL TRANSMISSION OPERATION (IF EQUIPPED) 1 3 5 2 4 R Using the clutch The manual transmission has a starter interlock that prevents cranking the engine unless the clutch pedal is fully depressed. To start the vehicle: 1. Make sure the parking brake is fully set. 2. Press the clutch pedal to the floor, then put the gearshift lever in the neutral position. 3. Start the engine. 4. Press the brake pedal and move the gearshift lever to the desired gear; 1 (First) or R (Reverse). 5.
Driving Recommended shift speeds Downshift according to the following charts for your specific engine/drivetrain combination: Upshifts when accelerating (for best fuel economy) Transfer case position (if equipped) Shift from: 2H or 4H 4L 1-2 10 mph (14 km/h) 4 mph (5 km/h) 2-3 22 mph (32 km/h) 9 mph (11 km/h) 3-4 33 mph (50 km/h) 13 mph (19 km/h) 4 - 5 (Overdrive) 41 mph (71 km/h) 17 mph (27 km/h) Upshifts when cruising (recommended for best fuel economy) Transfer case position (if equipped) Shift from: 2H
Driving Parking your vehicle 1. Apply the brake and shift into the neutral position. 2. Fully apply the parking brake, then shift into 1 (First). 3. Turn the ignition off. Do not park your vehicle in Neutral, it may move unexpectedly and injure someone. Use 1 (First) gear and set the parking brake fully. Removing the key Turn the ignition off, push the release lever (located above the ignition), then turn the key toward you and remove the key.
Driving 4WD system will not engage. This is normal and should be no reason for concern. Refer to Shifting to/from 4WD Low for proper operation. 4WD system indicator lights • 4x4 - Momentarily illuminates 4x4 when the vehicle is started. Illuminates when 4H (4WD High) is engaged. • 4x4 LOW – Momentarily 4x4 illuminates when the vehicle is LOW started. Illuminates when 4L (4WD Low) is engaged.
Driving 1. Bring the vehicle to a complete stop 2. Depress the brake 3. On vehicles equipped with an automatic transmission, place the transmission in N (Neutral); on vehicles equipped with a manual transmission, depress the clutch. 4. Move the 4WD control to the desired position. • If shifting into 4L (4WD Low), wait for the 4WD LOW light in the instrument cluster to turn on indicating the shift is complete.
Driving • Be extremely careful when driving on pavement made slippery by loose sand, water, gravel, snow or ice. If your vehicle goes off the edge of the pavement • If your vehicle goes off the edge of the pavement, slow down, but avoid severe brake application, ease the vehicle back onto the pavement only after reducing your speed. Do not turn the steering wheel too sharply while returning to the road surface.
Driving Emergency maneuvers • In an unavoidable emergency situation where a sudden sharp turn must be made, remember to avoid “over-driving” your vehicle, i.e., turn the steering wheel only as rapidly and as far as required to avoid the emergency. Excessive steering will result in less vehicle control, not more. Additionally, smooth variations of the accelerator and/or brake pedal pressure should be utilized if changes in vehicle speed are called for.
Driving Normal characteristics On some 4WD models, the initial shift from two-wheel drive to 4x4 while the vehicle is moving can cause some momentary clunk and ratcheting sounds. Sand When driving over sand, try to keep all four wheels on the most solid area of the trail. Avoid reducing the tire pressures but shift to a lower gear and drive steadily through the terrain. Apply the accelerator slowly and avoid spinning the wheels.
Driving Driving through deep water may damage the transmission. If the front or rear axle is submerged in water, the axle lubricant should be replaced. After driving through mud, clean off residue stuck to rotating driveshafts and tires. Excess mud stuck on tires and rotating driveshafts causes an imbalance that could damage drive components. “Tread Lightly” is an educational program designed to increase public awareness of land-use regulations and responsibilities in our nations wilderness areas.
Driving Descend a hill in the same gear you would use to climb up the hill to avoid excessive brake application and brake overheating. Do not descend in neutral; instead, disengage overdrive or manually shift to a lower gear. When descending a steep hill, avoid sudden hard braking as you could lose control. When you brake hard, the front wheels can’t turn and if they aren’t turning, you won’t be able to steer. The front wheels have to be turning in order to steer the vehicle.
Driving Maintenance and Modifications The suspension and steering systems on your vehicle have been designed and tested to provide predictable performance whether loaded or empty and durable load carrying capability. For this reason, Ford Motor Company strongly recommends that you do not make modifications such as adding or removing parts (such as lift kits or stabilizer bars) or by using replacement parts not equivalent to the original factory equipment.
Roadside Emergencies ROADSIDE ASSISTANCE Getting roadside assistance To fully assist you should you have a vehicle concern, Ford Motor Company offers a complimentary roadside assistance program. This program is separate from the New Vehicle Limited Warranty.
Roadside Emergencies Canadian customers refer to your Owner Information Guide for information on: • coverage period • exact fuel amounts • towing of your disabled vehicle • emergency travel expense reimbursement • travel planning benefits Using roadside assistance Complete the roadside assistance identification card and place it in your wallet for quick reference. In the United States, this card is found in the Owner Guide portfolio in the glove compartment.
Roadside Emergencies HAZARD FLASHER The hazard flasher is located on the steering column, just behind the steering wheel. The hazard flashers will operate when the ignition is in any position or if the key is not in the ignition. Push in the flasher control and all front and rear direction signals will flash. Press the flasher control again to turn them off. Use it when your vehicle is disabled and is creating a safety hazard for other motorists.
Roadside Emergencies The fuel pump shut-off switch is located under the right-hand side of the glove box, just above the carpet. To reset the switch: 1. Turn the ignition OFF. 2. Check the fuel system for leaks. 3. If no leaks are apparent, reset the switch by pushing in on the reset button. 4. Turn the ignition ON. 5. Wait a few seconds and return the key to OFF. 6. Make another check for leaks. FUSES AND RELAYS Fuses If electrical components in the vehicle are not working, a fuse may have blown.
Roadside Emergencies Standard fuse amperage rating and color COLOR Fuse rating Mini fuses Standard fuses Maxi fuses 2A 3A 4A 5A 7.
Roadside Emergencies The fuses are coded as follows: Fuse/Relay Location 1 2 3 4 5 6 7 8 Fuse Amp Rating 5A 10A 10A 10A 30A 10A 5A 10A 9 5A 182 2007 Ranger (ran) Owners Guide (post-2002-fmt) USA (fus) Passenger Compartment Fuse Panel Description Instrument panel dimmer switch Trailer tow park lamps Right low beam headlamp Left low beam headlamp Windshield wipers/washer Radio (RUN/ACCY) Not used (spare) Restraints Control Module (RCM), PADI (Passenger Air bag Deactivation Indicator), Occupant classifi
Roadside Emergencies Fuse/Relay Location 10 Fuse Amp Rating 10A 11 10A 12 15A 13 14 15A 15A 15 16 17 18 19 — 30A cartridge fuse 15A — 20A 20 10A 21 22 23 24 25 26 27 5A 5A 30A 20A — 2A 10A 28 29 15A 20A Passenger Compartment Fuse Panel Description Cluster (RUN/START), 4x4 module (RUN/START) Smart Junction Box (SJB) (Logic power) Audiophile subwoofer amplifier, Satellite radio Horn, Interior lamps High beam headlamp, High beam indicator (cluster) One-touch down relay Power windows Turn signal
Roadside Emergencies Fuse/Relay Location 30 31 Fuse Amp Rating 5A 20A 32 33 5A 5A 34 35 20A 15A Passenger Compartment Fuse Panel Description Power mirrors Front park lamps, Rear park lamps, License plate lamps, Dimmer switch, Trailer tow park lamps Brake switch (logic) Instrument cluster battery feed (B+) Power point Power locks Power distribution box The power distribution box is located in the engine compartment.
Roadside Emergencies If the battery has been disconnected and reconnected, refer to the Battery section of the Maintenance and Specifications chapter. 2.
Roadside Emergencies Fuse/Relay Location 12 13 14 15 16 17 Fuse Amp Rating — 30A** — — — 40A** 18 19 20 21 — 20A** — 10A* 22 23 24 25 26 27 28 29 30 31 32 33 — 30A* — 10A* — — — — — 15A* — 30A* 34 35 36 37 38 39 — — — — 7.
Roadside Emergencies Fuse/Relay Location 40 41 42 43 Fuse Amp Rating — 10A* 7.
Roadside Emergencies 3.0L and 4.
Roadside Emergencies Fuse/Relay Location 16 17 18 19 20 21 Fuse Amp Rating — 40A** — — — 10A* 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 — 30A* — 10A* — 20A* — — — 15A* — 30A* — — — — 7.5A* 15A* — 10A* 7.
Roadside Emergencies Fuse/Relay Fuse Amp Location Rating 45A — 45B — 46A — 46B — 47 — 48A — 48B — 51 — 52 — 53 — 54 — 55 — 56 — * Mini Fuses ** Maxi Fuses Power Distribution Box Description Wiper HI/LO relay Wiper Park/Run relay A/C clutch solenoid Washer pump relay PCM relay Fuel pump relay, Fuel injectors relay Fog lamp relay Not used Not used Not used Not used Blower relay Starter relay CHANGING THE TIRES If you get a flat tire while driving: • do not brake heavily.
Roadside Emergencies Refer to Tire Pressure Monitoring System (TPMS) in the Tires, Wheels and Loading chapter for important information. If the tire pressure monitor sensor becomes damaged, it will no longer function. Dissimilar spare tire/wheel information Failure to follow these guidelines could result in an increased risk of loss of vehicle control, injury or death. If you have a dissimilar spare tire/wheel, then it is intended for temporary use only.
Roadside Emergencies Use of one of the dissimilar spare tires listed above at any one wheel location can lead to impairment of the following: • Handling, stability and braking performance • Comfort and noise • Ground clearance and parking at curbs • Winter weather driving capability • Wet weather driving capability For vehicles equipped with 4WD, it is not recommended that the vehicle be operated in 4WD modes with a temporary emergency spare tire.
Roadside Emergencies Full-size Matching Spare Tire/Wheel Information This spare tire/wheel will match the road tire/wheel. When driving with the full size matching spare tire/wheel, do not exceed 70 mph (113 km/h). It is intended for temporary use only. This means if you need to use it, you should replace it as soon as possible. Location of the spare tire and tools Note: The tire pressure monitoring system (TPMS) indicator light will illuminate when the spare is in use.
Roadside Emergencies Removing the spare tire 1. Assemble the jack handle to the lug wrench as shown in the illustrations. When connecting the jack handle, assemble the following: • one handle extension and one typical extension. To assemble, slide parts together. To disconnect, depress button and pull apart. • one wheel nut wrench. Depress button and slide together. 2.
Roadside Emergencies 3. Insert the square end of the jack handle into the rear access hole located just above the rear bumper and below the tailgate. Forward motion will stop and resistance to turning will be felt when properly engaged. 4. Turn the handle counterclockwise until tire is lowered to the ground and the cable is slightly slack. 5. With the spare tire on the ground, remove the retainer from the spare tire.
Roadside Emergencies 1. Park on a level surface, activate hazard flashers and place gearshift lever in P (Park) (automatic transmission) or 1 (First) (manual transmission). 2. Set the parking brake and turn engine OFF. 3. Block the diagonally opposite wheel. 4. Insert tapered end of the lug wrench behind hub caps and twist them off. 5. Loosen each wheel lug nut one-half turn counterclockwise but do not remove them until the wheel is raised off the ground. 6.
Roadside Emergencies • Rear To lessen the risk of personal injury, do not put any part of your body under the vehicle while changing a tire. Do not start the engine when your vehicle is on the jack. The jack is only meant for changing the tire. • Never use the differential as a jacking point. 7. Remove the wheel lug nuts with the lug wrench. 8. Replace the flat tire with the spare tire, making sure the valve stem is facing outward. Reinstall the lug nuts until the wheel is snug against the hub.
Roadside Emergencies Stowing the flat/spare tire Note: Failure to follow spare tire stowage instructions may result in failure of cable or loss of spare tire. 1. Lay the tire on the ground with the valve stem facing up. 2. Slide the wheel partially under the vehicle and install the wire and retainer through the center of the wheel. 3. Turn the jack handle clockwise until the tire is raised to its original position underneath the vehicle.
Roadside Emergencies When a wheel is installed, always remove any corrosion, dirt or foreign materials present on the mounting surfaces of the wheel or the surface of the wheel hub, brake drum or brake disc that contacts the wheel. Ensure that any fasteners that attach the rotor to the hub are secured so they do not interfere with the mounting surfaces of the wheel.
Roadside Emergencies 4. Check all battery terminals and remove any excessive corrosion before you attach the battery cables. Ensure that vent caps are tight and level. 5. Turn the heater fan on in both vehicles to protect from any electrical surges. Turn all other accessories off. Connecting the jumper cables + + – – 1. Connect the positive (+) jumper cable to the positive (+) terminal of the discharged battery.
Roadside Emergencies + + – – 3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery. + + – – 4. Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle’s engine, away from the battery and the carburetor/fuel injection system. Do not use fuel lines, engine rocker covers or the intake manifold as grounding points. Do not connect the end of the second cable to the negative (-) terminal of the battery to be jumped.
Roadside Emergencies 3. Once the disabled vehicle has been started, run both engines for an additional three minutes before disconnecting the jumper cables. Removing the jumper cables + + – – Remove the jumper cables in the reverse order that they were connected. 1. Remove the jumper cable from the ground metal surface. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. + + – – 2.
Roadside Emergencies + + – – 3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’s battery. + + – – 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’s battery. After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn its idle conditions.
Roadside Emergencies WRECKER TOWING If you need to have your vehicle towed, contact a professional towing service or, if you are a member of a roadside assistance program, your roadside assistance service provider. It is recommended that your vehicle be towed with a wheel lift or flatbed equipment. Do not tow with a slingbelt. Ford Motor Company has not approved a slingbelt towing procedure.
Customer Assistance GETTING THE SERVICES YOU NEED At home You must take your Ford vehicle to an authorized dealer for warranty repairs. While any authorized dealer handling your vehicle line will provide warranty service, we recommend you return to your selling authorized dealer who wants to ensure your continued satisfaction. Please note that certain warranty repairs require special training and/or equipment, so not all authorized dealers are authorized to perform all warranty repairs.
Customer Assistance In Canada: Customer Relationship Centre Ford Motor Company of Canada, Limited P.O. Box 2000 Oakville, Ontario L6J 5E4 1-800-565-3673 (FORD) www.ford.ca If you own a Lincoln vehicle and are away from home when your vehicle needs service, or if you need more help than the authorized dealer could provide, after following the steps described above, contact the Ford Customer Relationship Center to find an authorized dealer to help you.
Customer Assistance In some states (in the U.S.) you must directly notify Ford in writing before pursuing remedies under your state’s warranty laws. Ford is also allowed a final repair attempt in some states. In the United States, a warranty dispute must be submitted to the BBB AUTO LINE before taking action under the Magnuson-Moss Warranty Act, or to the extent allowed by state law, before pursuing replacement or repurchase remedies provided by certain state laws.
Customer Assistance THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM (U.S. ONLY) Your satisfaction is important to Ford Motor Company and to your dealer. Experience has shown that our customers have been very successful in achieving satisfaction by following the three-step procedure outlined on the front page of the Warranty Guide. However, if your warranty concern has not been resolved using the three-step procedure, you may be eligible to participate in the BBB AUTO LINE program.
Customer Assistance UTILIZING THE MEDIATION/ARBITRATION PROGRAM (CANADA ONLY) For vehicles delivered to authorized Canadian dealers. In those cases where you continue to feel that the efforts by Ford of Canada and the authorized dealer to resolve a factory-related vehicle service concern have been unsatisfactory, Ford of Canada participates in an impartial third party mediation/arbitration program administered by the Canadian Motor Vehicle Arbitration Plan (CAMVAP).
Customer Assistance If you did not take advantage of the Ford Extended Service Plan at the time of purchasing your vehicle, you may still be eligible. Since this information is subject to change, please ask your authorized dealer for complete details about Ford Extended Service Plan coverage options, or visit the Ford ESP website at www.ford-esp.com. GETTING ASSISTANCE OUTSIDE THE U.S. AND CANADA Before exporting your vehicle to a foreign country, contact the appropriate foreign embassy or consulate.
Customer Assistance ORDERING ADDITIONAL OWNER’S LITERATURE To order the publications in this portfolio, contact Helm, Incorporated at: HELM, INCORPORATED P.O. Box 07150 Detroit, Michigan 48207 Or call: For a free publication catalog, order toll free: 1-800-782-4356 Monday-Friday 8:00 a.m. - 6:00 p.m. EST Helm, Incorporated can also be reached by their website: www.helminc.com. (Items in this catalog may be purchased by credit card, check or money order.
Customer Assistance To contact NHTSA, you may call the Vehicle Safety Hotline toll-free at 1–888–327–4236 (TTY: 1–800–424–9153); go to http://www.safercar.gov; or write to: Administrator NHTSA 400 Seventh Street, SW Washington, D.C. 20590 You can also obtain other information about motor vehicle safety from http://www.safercar.gov.
Cleaning WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutral pH shampoo, such as Motorcraft Detail Wash (ZC-3–A), which is available from your authorized dealer. • Never use strong household detergents or soap, such as dish washing or laundry liquid. These products can discolor and spot painted surfaces. • Never wash a vehicle that is “hot to the touch” or during exposure to strong, direct sunlight.
Cleaning WAXING Applying Motorcraft Paint Sealant (ZC-45) to your vehicle every six months will assist in reducing minor scratches and paint damage. • Wash the vehicle first. • Do not use waxes that contain abrasives; use Motorcraft Premium Liquid Wax (ZC-53-A), which is available from your authorized dealer, or an equivalent quality product.
Cleaning ENGINE Engines are more efficient when they are clean because grease and dirt buildup keep the engine warmer than normal. When washing: • Take care when using a power washer to clean the engine. The high-pressure fluid could penetrate the sealed parts and cause damage. • Do not spray a hot engine with cold water to avoid cracking the engine block or other engine components. • Spray Motorcraft Engine Shampoo and Degreaser (ZC-20) on all parts that require cleaning and pressure rinse clean.
Cleaning • 3.0L V6 engine • 4.0L SOHC V6 engine • Never wash or rinse the engine while it is running; water in the running engine may cause internal damage. PLASTIC (NON-PAINTED) EXTERIOR PARTS Use only approved products to clean plastic parts. These products are available from your authorized dealer. • For routine cleaning, use Motorcraft Detail Wash (ZC-3–A). • If tar or grease spots are present, use Motorcraft Bug and Tar Remover (ZC-42).
Cleaning WINDOWS AND WIPER BLADES The windshield, rear and side windows and the wiper blades should be cleaned regularly. If the wipers do not wipe properly, substances on the vehicle’s glass or the wiper blades may be the cause. These may include hot wax treatments used by commercial car washes, water repellant coatings, tree sap, or other organic contamination; these contaminants may cause squeaking or chatter noise from the blades, and streaking and smearing of the windshield.
Cleaning • Be certain to wash or wipe your hands clean if you have been in contact with certain products such as insect repellent and suntan lotion in order to avoid possible damage to the interior painted surfaces. INTERIOR For fabric, carpets, cloth seats and safety belts: • Remove dust and loose dirt with a vacuum cleaner. • Remove light stains and soil with Motorcraft Professional Strength Carpet & Upholstery Cleaner (ZC-54).
Cleaning FORD AND LINCOLN MERCURY CAR CARE PRODUCTS Your Ford or Lincoln Mercury authorized dealer has many quality products available to clean your vehicle and protect its finishes. These quality products have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and appearance of your vehicle. Each product is made from high quality materials that meet or exceed rigid specifications.
Maintenance and Specifications SERVICE RECOMMENDATIONS To help you service your vehicle, we provide scheduled maintenance information which makes tracking routine service easy. If your vehicle requires professional service, your authorized dealer can provide the necessary parts and service. Check your Warranty Guide/Owner Information Guide to find out which parts and services are covered. Use only recommended fuels, lubricants, fluids and service parts conforming to specifications.
Maintenance and Specifications 2. Block the wheels. To reduce the risk of vehicle damage and/or personal burn injuries do not start your engine with the air cleaner removed and do not remove it while the engine is running. OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located under the bottom of the instrument panel near the steering column. 2. Go to the front of the vehicle and release the auxiliary latch that is located under the front center of the hood. 3.
Maintenance and Specifications IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 2.3L I4 engine 1. Windshield washer fluid reservoir 2. Engine coolant reservoir 3. Engine oil dipstick 4. Transmission fluid dipstick (automatic transmission) 5. Engine oil filler cap 6. Brake fluid reservoir 7. Power distribution box 8. Clutch fluid reservoir (manual transmission) 9. Battery 10. Power steering fluid reservoir 11.
Maintenance and Specifications 3.0L V6 engine 1. Engine coolant reservoir 2. Windshield washer fluid reservoir 3. Engine oil filler cap 4. Automatic transmission fluid dipstick (if equipped) 5. Engine oil dipstick 6. Brake fluid reservoir 7. Power distribution box 8. Clutch fluid reservoir (if equipped) 9. Battery 10. Power steering fluid reservoir 11.
Maintenance and Specifications 4.0L SOHC V6 engine 2 1 3 4 5 6 7 11 10 9 1. Windshield washer fluid reservoir 2. Automatic transmission fluid dipstick (if equipped) 3. Engine oil filler cap 4. Engine oil dipstick 5. Brake fluid reservoir 6. Power distribution box 7. Clutch fluid reservoir (if equipped) 8. Battery 9. Power steering fluid reservoir 10. Air filter assembly 11.
Maintenance and Specifications WINDSHIELD WASHER FLUID • 2.3L engine SHER FL WA UID • 3.0L and 4.0L engines Add fluid to fill the reservoir if the level is low. In very cold weather, do not fill the reservoir completely. Only use a washer fluid that meets Ford specification WSB-M8B16-A2. Do not use any special washer fluid such as windshield water repellent type fluid or bug wash. They may cause squeaking, chatter noise, streaking and smearing.
Maintenance and Specifications If you operate your vehicle in temperatures below 40° F (4.5°C), use washer fluid with antifreeze protection. Failure to use washer fluid with antifreeze protection in cold weather could result in impaired windshield vision and increase the risk of injury or accident. Note: Do not put washer fluid in the engine coolant reservoir. Washer fluid placed in the cooling system may harm engine and cooling system components. CHANGING THE WIPER BLADES 1.
Maintenance and Specifications 4. Open the hood. Protect yourself from engine heat. 5. Locate and carefully remove the engine oil level indicator (dipstick). • 2.3L I4 engine MIN MAX • 3.
Maintenance and Specifications • 4.0L SOHC V6 engine 6. Wipe the indicator clean. Insert the indicator fully, then remove it again. • If the oil level is between the two holes or between the MIN and MAX marks (depending on application), the oil level is acceptable, DO NOT ADD OIL. • If the oil level is below the lower hole or the MIN mark, add enough oil to raise the level between the two holes or between the MIN-MAX range. • 2.
Maintenance and Specifications • 3.0L V6 engine • 4.0L SOHC V6 engine • Oil levels above the upper hole or MAX mark may cause engine damage. Some oil must be removed from the engine by an authorized dealer. 7. Put the indicator back in and ensure it is fully seated.
Maintenance and Specifications Adding engine oil 1. Check the engine oil. For instructions, refer to Checking the engine oil in this chapter. 2. If the engine oil level is not within the normal range, add only certified engine oil of the recommended viscosity. Remove the engine oil filler cap and use a funnel to pour the engine oil into the opening. 3. Recheck the engine oil level. Make sure the oil level is within the normal range on the engine oil level indicator (dipstick). 4.
Maintenance and Specifications Do not use supplemental engine oil additives, cleaners or other engine treatments. They are unnecessary and could lead to engine damage that is not covered by Ford warranty. Change your engine oil according to the appropriate schedule listed in the scheduled maintenance information. Ford production and aftermarket (Motorcraft) oil filters are designed for added engine protection and long life.
Maintenance and Specifications that does not meet Ford material and design specifications, start-up engine noises or knock may be experienced. It is recommended you use the appropriate Motorcraft oil filter (or another brand meeting Ford specifications) for your engine application. BATTERY Your vehicle is equipped with a Motorcraft maintenance-free battery which normally does not require additional water during its life of service.
Maintenance and Specifications When lifting a plastic-cased battery, excessive pressure on the end walls could cause acid to flow through the vent caps, resulting in personal injury and/or damage to the vehicle or battery. Lift the battery with a battery carrier or with your hands on opposite corners. Keep batteries out of reach of children. Batteries contain sulfuric acid. Avoid contact with skin, eyes or clothing.
Maintenance and Specifications TU LE AD RE If the battery has been disconnected or a new battery has been installed, the clock and the preset radio stations must be reset once the battery is reconnected. • Always dispose of automotive batteries in a responsible manner. Follow your local authorized standards for disposal. Call your local authorized recycling center to find out more about recycling automotive batteries.
Maintenance and Specifications • 2.3L engines • 3.0L and 4.
Maintenance and Specifications When the engine is cold, check the level of the engine coolant in the reservoir. • The engine coolant should be at the “FULL COLD” level or within the “COLD FILL RANGE” as listed on the engine coolant reservoir (depending upon application). • Refer to the scheduled maintenance information for service interval schedules. • Be sure to read and understand Precautions when servicing your vehicle in this chapter.
Maintenance and Specifications specification WSS-M97B44-D, with the factory-filled coolant. Mixing Motorcraft Specialty Orange Engine Coolant or any orange-colored extended life product with your factory filled coolant can result in degraded corrosion protection. • A large amount of water without engine coolant may be added, in case of emergency, to reach a vehicle service location.
Maintenance and Specifications 5. Fill the coolant reservoir slowly with the proper coolant mixture (see above), to within the “COLD FILL RANGE” or the “FULL COLD” level on the reservoir. If you removed the radiator cap in an overflow system, fill the radiator until the coolant is visible and radiator is almost full. 6. Replace the cap. Turn until tightly installed. (Cap must be tightly installed to prevent coolant loss.
Maintenance and Specifications • NEVER increase the coolant concentration above 60%. • Increased engine coolant concentrations above 60% will decrease the overheat protection characteristics of the engine coolant and may cause engine damage. • Refer to the chart on the coolant container to ensure the coolant concentration in your vehicle will provide adequate freeze protection at the temperatures in which you drive in the winter months.
Maintenance and Specifications The fuel system may be under pressure. If the fuel filler cap is venting vapor or if you hear a hissing sound, wait until it stops before completely removing the fuel filler cap. Otherwise, fuel may spray out and injure you or others. If you do not use the proper fuel filler cap, excessive vacuum in the fuel tank may damage the fuel system or cause the fuel cap to disengage in a collision, which may result in possible personal injury.
Maintenance and Specifications • Be particularly careful if you are taking “Antabuse” or other forms of disulfiram for the treatment of alcoholism. Breathing gasoline vapors, or skin contact could cause an adverse reaction. In sensitive individuals, serious personal injury or sickness may result. If fuel is splashed on the skin, promptly wash skin thoroughly with soap and water. Consult a physician immediately if you experience an adverse reaction.
Maintenance and Specifications Fuel Filler Cap Your vehicle is equipped with a 1/4 turn fuel filler cap, which requires the handle to be rotated 1/4 of a turn for removal or installation. When fueling your vehicle: 1. Turn the engine off. 2. Carefully turn the fuel filler cap counterclockwise 1/4 of a turn until it releases from the fuel filler pipe. 3. Carefully hang the cap from the tether. 4. To install the cap, place the cap into the filler pipe and rotate until you hear at least one click.
Maintenance and Specifications Choosing the right fuel Use only UNLEADED fuel or UNLEADED fuel blended with a maximum of 10% ethanol. Your vehicle was not designed to run on E85 fuels that are blended with a maximum of 85% ethanol. The use of leaded fuel is prohibited by law and could damage your vehicle. Do not use fuel containing methanol. It can damage critical fuel system components.
Maintenance and Specifications Fuel quality If you are experiencing starting, rough idle or hesitation driveability problems, try a different brand of unleaded gasoline. “Premium” unleaded gasoline is not recommended for vehicles designed to use “Regular” unleaded gasoline because it may cause these problems to become more pronounced. If the problems persist, see your authorized dealer. Do not add aftermarket fuel additive products to your fuel tank.
Maintenance and Specifications possible. Fuel expense, frequency of fill-ups or fuel gauge readings are NOT accurate as a measure of fuel economy. We do not recommend taking fuel economy measurements during the first 1,000 miles (1,600 km) of driving (engine break-in period). You will get a more accurate measurement after 2,000 miles-3,000 miles (3,000 km–5,000 km).
Maintenance and Specifications 3. After at least three to five tank fill-ups, fill the fuel tank and record the current odometer reading. 4. Subtract your initial odometer reading from the current odometer reading. 5. Follow one of the simple calculations in order to determine fuel economy: Calculation 1: Divide total miles traveled by total gallons used. Calculation 2: Multiply liters used by 100, then divide by total kilometers traveled.
Maintenance and Specifications • Resting your foot on the brake pedal while driving may reduce fuel economy. • Combine errands and minimize stop-and-go driving. Maintenance • Keep tires properly inflated and use only recommended size. • Operating a vehicle with the wheels out of alignment will reduce fuel economy. • Use recommended engine oil. Refer to Maintenance product specifications and capacities in this chapter. • Perform all regularly scheduled maintenance items.
Maintenance and Specifications It is important to note the box in the lower left corner of the window sticker. These numbers represent the Range of MPG (L/100 km) expected on the vehicle under optimum conditions. Your fuel economy may vary depending upon the method of operation and conditions. EMISSION CONTROL SYSTEM Your vehicle is equipped with various emission control components and a catalytic converter which will enable your vehicle to comply with applicable exhaust emission standards.
Maintenance and Specifications Do not make any unauthorized changes to your vehicle or engine. By law, vehicle owners and anyone who manufactures, repairs, services, sells, leases, trades vehicles, or supervises a fleet of vehicles are not permitted to intentionally remove an emission control device or prevent it from working. Information about your vehicle’s emission system is on the Vehicle Emission Control Information Decal located on or near the engine.
Maintenance and Specifications Readiness for Inspection/Maintenance (I/M) testing Some state/provincial and local governments may have Inspection/Maintenance (I/M) programs to inspect the emission control equipment on your vehicle. Failure to pass this inspection could prevent you from getting a vehicle registration.
Maintenance and Specifications POWER STEERING FLUID • 2.3L I4 engine • 3.0L V6 engine • 4.0L V6 engine DO N P ING OVER FILOL T OW FLUIDEER ER ST Check the power steering fluid. Refer to the scheduled maintenance guide for the service interval schedules. If adding fluid is necessary, use only MERCON威 ATF.
Maintenance and Specifications 1. Start the engine and let it run until it reaches normal operating temperature (the engine coolant temperature gauge indicator will be near the center of the normal area between H and C). 2. While the engine idles, turn the steering wheel left and right several times. 3. Turn the engine off. 4. Check the fluid level in the reservoir. It should be between the MIN and MAX lines. Do not add fluid if the level is within this range. 5.
Maintenance and Specifications 1. Clean the reservoir cap before removal to prevent dirt and water from entering the reservoir. 2. Remove cap and rubber diaphragm from reservoir. 3. Add fluid until the level reaches the step in the reservoir. 4. Reinstall rubber diaphragm and cap onto reservoir. TRANSMISSION FLUID Checking automatic transmission fluid • Refer to scheduled maintenance information for scheduled check and change intervals. • Transmission does not consume fluid.
Maintenance and Specifications the Maintenance product specifications and capacities section in this chapter for the correct fluid type. The use of any other non-approved fluid may cause internal transmission damage. 10. Fluid can be checked at ambient temperatures between 50–95°F (10–30°C). DO NOT ADD fluid until the transmission is at normal operating temperatures or the transmission will be overfilled. Low fluid level Do not drive the vehicle if the fluid level is at or below the bottom of the dipstick.
Maintenance and Specifications 3. Fluid level should be at the bottom of the opening. 4. Add enough fluid through the filler opening so that the fluid level is at the bottom of the opening. 5. Install and tighten the fill plug securely. Use only fluid that meets Ford specifications. Refer to the Maintenance product specifications and capacities section in this chapter. TRANSFER CASE FLUID (IF EQUIPPED) 1. Clean the filler plug. 2. Remove the filler plug and inspect the fluid level. 3.
Maintenance and Specifications DRIVELINE UNIVERSAL JOINT AND SLIP YOKE Your vehicle may be equipped with universal joints that require lubrication. Refer to the scheduled maintenance information for maintenance intervals. If the original universal joints are replaced with universal joints equipped with grease fittings, lubrication will also be necessary. AIR FILTER Refer to scheduled maintenance information for the appropriate intervals for changing the air filter element.
Maintenance and Specifications 6. Install a new air filter element. Be careful not to crimp the filter element edges between the air filter housing and cover. This could cause filter damage and allow unfiltered air to enter the engine if not properly seated. 7. Replace the air filter housing cover and secure the clamps. 8. Replace the air inlet tube and secure the clamp. Note: Failure to use the correct air filter element may result in severe engine damage.
Maintenance and Specifications 2 For spark plug replacement, see your authorized dealer. Refer to scheduled maintenance information for the appropriate intervals for changing the spark plugs. Replace the spark plugs with ones that meet Ford material and design specifications for your vehicle, such as Motorcraft or equivalent replacement parts. The customer warranty may be void for any damage to the engine if such spark plugs are not used.
XG-1-C or XG-1-K / ESA-M1C75-B Motorcraft Premium Long-Life Grease — XL-6 / ESR-M13P4-A XG-4 or XL-5 / ESB-M1C93-B Silicone Spray Lubricant PM-1 or PM-1-C / ESA-M6C25-A or WSS-M6C62-A Ford part number / Ford specification Multi-Purpose Grease — Door weather strips Ford part name or equivalent Motorcraft High Performance DOT 3 Motor Vehicle Brake Fluid — Fill to line or step (for clutch) on reservoir Brake fluid and clutch fluid (if equipped) Hinges, door checks, latches, striker plates, fuel f
Engine coolant (2.3L engine with manual transmission) Engine coolant (2.3L engine with automatic transmission) Engine coolant (3.0L engine with manual transmission) Engine coolant (3.0L engine with automatic transmission) Engine coolant (4.0L engine with manual transmission) Engine coolant (4.0L engine with automatic transmission) Cooling system stop leak pellets Item 260 2007 Ranger (ran) Owners Guide (post-2002-fmt) USA (fus) — 13.2 quarts (12.5L) 13.7 quarts (13.0L) 14.8 quarts (14.0L) 15.
2007 Ranger (ran) Owners Guide (post-2002-fmt) USA (fus) Motorcraft MERCON威V ATF4 Ford part name or equivalent Motorcraft SAE 5W-20 4.0 quarts (3.8L) Premium Synthetic Blend Motor Oil (US) Motorcraft SAE 5W-20 Super Premium Motor 4.5 quarts (4.3L) Oil (Canada)2 Motorcraft SAE 5W-30 Premium Synthetic Blend Motor Oil (US) 5.0 quarts (4.7L) Motorcraft SAE 5W-30 Super Premium Motor Oil (Canada)2 Capacity Automatic Transmission fluid (4x2 with 2.3L 9.9 quarts (9.4L)3 engine) Automatic Transmission 10.
1.25 quarts (1.2L) Fill between MAX / MIN line on reservoir 2.8 quarts (2.65L)5 Capacity Motorcraft MERCON威 ATF Ford part name or equivalent Front axle fluid (4X4) 3.6 pints (1.7L) Motorcraft SAE 80W-90 Premium Rear Axle Lubricant Motorcraft SAE 80W-90 5.0-5.3 pints Rear axle fluid –All Premium Rear Axle (except FX4 Level II) (2.4-2.5L)6,7,8 Lubricant Motorcraft SAE 75W-140 Rear axle fluid (FX4 5.25-5.5 pints Synthetic Rear Axle 6,7,8 Level II only) (2.5-2.
— 19.5 gallons (73.8L) Fuel tank–SuperCab — Ford part number / Ford specification 2007 Ranger (ran) Owners Guide (post-2002-fmt) USA (fus) Add 4 oz. (118 ml) of Additive Friction Modifier XL-3 or equivalent meeting Ford specification EST-M2C118-A for complete refill of Traction-Lok axles. 8 Service refill capacities are determined by filling the rear axle 1/4 inch to 9/16 inch (6mm to 14mm) below the bottom of the filler hole. 7 Traction-Lok axles use 4.75-5.0 pints (2.2-2.
Maintenance and Specifications ENGINE DATA Engine Cubic inches Required fuel Firing order Ignition system Spark plug gap Compression ratio 2.3L I4 engine 138 87 octane 1-3-4-2 EDIS 0.049–0.053 inch (1.25–1.35 mm) 3.0L V6 engine 182 87 octane 1-4-2-5-3-6 EDIS 0.051–0.057 inch (1.29–1.45 mm) 4.0L V6 engine 245 87 octane 1-4-2-5-3-6 EDIS 0.052–0.056 inch (1.32–1.42 mm) 9.7:1 9.6:1 9.7:1 Engine drivebelt routing • 2.3L I4 Engine without A/C (with A/C similar) • 3.
Maintenance and Specifications • 3.0L V6 Engine with A/C • 4.
Maintenance and Specifications IDENTIFYING YOUR VEHICLE Safety Compliance Certification Label The National Highway Traffic Safety Administration Regulations require that a Safety Compliance Certification Label be affixed to a vehicle and prescribe where the Safety Compliance Certification Label may be located. The Safety Compliance Certification Label is located on the structure (B-Pillar) by the trailing edge of the driver’s door or the edge of the driver’s door.
Maintenance and Specifications The Vehicle Identification Number (VIN) contains the following information: 1. World manufacturer identifier 2. Brake system / Gross Vehicle Weight Rating (GVWR) / Restraint System 3. Vehicle line, series, body type 4. Engine type 5. Check digit 6. Model year 7. Assembly plant 8. Production sequence number TRANSMISSION/TRANSAXLE CODE DESIGNATIONS You can find a transmission/transaxle code on the Safety Compliance Certification Label.
Accessories GENUINE FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Ford Accessories are available for your vehicle through your local Ford or Ford of Canada dealer. These quality accessories have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and aerodynamic appearance of your vehicle. In addition, each accessory is made from high quality materials and meets or exceeds Ford’s rigorous engineering and safety specifications.
Accessories Interior style Consoles Electrochromatic compass/temperature interior mirrors Floor mats Lifestyle Ash cup / smoker’s package Bedliners and bedmats Cargo organization and management Towing mirrors Trailer hitches, wiring harnesses and accessories TripTunes娂 Peace of mind Mobile-ease娂 hands-free communication system Remote start Vehicle security systems Wheel locks Not all accessories are available for all models.
Accessories • To avoid interference with other vehicle functions, such as anti-lock braking systems, amateur radio users who install radios and antennas onto their vehicle should not locate the Amateur Radio Antennas in the area of the driver’s side hood. • Electrical or electronic accessories or components that are added to the vehicle by the authorized dealer or the owner may adversely affect battery performance and durability.
Index A Air cleaner filter ...............256–257 Airbag supplemental restraint system ....................98–99 and child safety seats ............101 description ................................99 disposal ....................................103 driver airbag ......................99, 101 indicator light .........................102 operation ...........................99, 101 passenger airbag ...............99, 101 Ambulance packages ....................8 Antifreeze (see Engine coolant) ................
Index AM/FM stereo CD ...............21, 24 CD-MP3 ...............................38, 41 Premium AM/FM stereo CD6/MP3 .............................29, 33 Clutch fluid ..........................................252 operation while driving ..........166 recommended shift speeds ....167 Console ........................................66 Coolant checking and adding ..............234 refill capacities ................238, 259 specifications ..........................259 Cruise control (see Speed control) ........
Index comparisons with EPA fuel economy estimates .................247 detergent in fuel .....................243 filling your vehicle with fuel ...........................239, 242, 245 filter, specifications ........239, 257 fuel pump shut-off switch .....179 improving fuel economy ........244 octane rating ...................243, 264 quality ......................................244 running out of fuel .................244 safety information relating to automotive fuels ................
Index Locks doors ..........................................73 Lubricant specifications ...........259 Lug nuts ....................................198 Lumbar support, seats ...............82 M Manual transmission .................166 fluid capacities ........................259 lubricant specifications ..........259 reverse .....................................167 Mirrors .........................................68 fold away ...................................68 side view mirrors (power) .......
Index SecuriLock passive anti-theft system ..........................................77 Servicing your vehicle ..............220 Setting the clock AM/FM stereo ...........................19 AM/FM stereo CD ...............21, 24 Premium AM/FM stereo CD6/MP3 .............................29, 33 Snowplowing .................................8 Spark plugs, specifications .....................257, 264 Special notice ambulance conversions ..............8 utility-type vehicles ....................
Index Windows power .........................................67 Windshield washer fluid and wipers ...................................65 276 2007 Ranger (ran) Owners Guide (post-2002-fmt) USA (fus) checking and adding fluid .....225 replacing wiper blades ...........226 Wrecker towing .........................
