Table of Contents Introduction Instrument Cluster 4 10 Warning and control lights Gauges 10 15 Entertainment Systems 18 AM/FM stereo AM/FM stereo with CD AM/FM stereo cassette with CD Climate Controls Heater only Manual heating and air conditioning Lights Headlamps Turn signal control Bulb replacement Driver Controls Windshield wiper/washer control Steering wheel adjustment Power windows Mirrors Speed control (Cruise control) 18 22 43 75 75 76 80 80 82 82 89 89 90 92 93 93 1
Table of Contents Locks and Security 105 Keys Locks Anti-theft system 105 105 106 Seating and Safety Restraints Seating Safety restraints Air bags Child restraints Driving 114 115 127 136 151 Starting Brakes Transmission operation Vehicle loading Trailer towing 151 155 159 179 181 Roadside Emergencies 194 Getting roadside assistance Hazard flasher switch Fuel pump shut-off switch Fuses and relays Changing tires Jump starting Wrecker towing 2 114 194 195 196 197 207 213 218
Table of Contents Customer Assistance Reporting safety defects (U.S. only) 219 228 Cleaning 229 Maintenance and Specifications 236 Engine compartment Engine oil Battery Fuel information Part numbers Refill capacities Lubricant specifications 238 241 248 255 278 279 282 Accessories 288 Index 291 All rights reserved.
Introduction CALIFORNIA Proposition 65 Warning WARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. In addition, certain fluids contained in vehicles and certain products of component wear contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
Introduction SAFETY AND ENVIRONMENT PROTECTION Warning symbols in this guide How can you reduce the risk of personal injury and prevent possible damage to others, your vehicle and its equipment? In this guide, answers to such questions are contained in comments highlighted by the warning triangle symbol. These comments should be read and observed.
Introduction SPECIAL NOTICES Emission warranty The New Vehicle Limited Warranty includes Bumper-to-Bumper Coverage, Safety Restraint Coverage, Corrosion Coverage, and 7.3L Power Stroke Diesel Engine Coverage. In addition, your vehicle is eligible for Emissions Defect and Emissions Performance Warranties. For a detailed description of what is covered and what is not covered, refer to the Warranty Guide that is provided to you along with your Owner’s Guide.
Introduction Using your vehicle with a snowplow Do not use this vehicle for snowplowing. Using your vehicle as an ambulance Do not use this vehicle as an ambulance. Your vehicle is not equipped with the Ford Ambulance Preparation Package. Electric vehicles For specific information regarding the operation of your electric vehicle, refer to the Electric Vehicle Owner’s Guide Supplement.
Introduction These are some of the symbols you may see on your vehicle.
Introduction Vehicle Symbol Glossary Power Windows Front/Rear Power Window Lockout Child Safety Door Lock/Unlock Interior Luggage Compartment Release Symbol Panic Alarm Engine Oil Engine Coolant Engine Coolant Temperature Do Not Open When Hot Battery Avoid Smoking, Flames, or Sparks Battery Acid Explosive Gas Fan Warning Power Steering Fluid Maintain Correct Fluid Level Emission System/Check Engine/Service Engine Soon Engine Air Filter Passenger Compartment Air Filter Jack Check fuel cap
Instrument Cluster WARNING LIGHTS AND CHIMES Warning lights and gauges can alert you to a vehicle condition that may become serious enough to cause expensive repairs. A warning light may illuminate when a problem exists with one of your vehicle’s functions. Many lights will illuminate when you start your vehicle to make sure the bulb works. If any light remains on after starting the vehicle, have the respective system inspected immediately.
Instrument Cluster should turn off. (A driving cycle consists of a cold engine startup followed by mixed city/highway driving.) No additional vehicle service is required. If the light remains on, have your vehicle serviced at the first available opportunity. Light is blinking: Engine misfire is occurring which could damage your catalytic converter. You should drive in a moderate fashion (avoid heavy acceleration and deceleration) and have your vehicle serviced at the first available opportunity.
Instrument Cluster Anti-lock brake system (ABS) To confirm the anti-lock brake system (ABS) warning light is ABS functional it will momentarily illuminate when the ignition is turned to the ON position (alternatively for some vehicles when the ignition is moved from the ON position to the START position, the light will momentarily illuminate just prior to reaching the START position). If the light remains on, continues to flash or fails to illuminate, have the ABS serviced immediately.
Instrument Cluster Check fuel cap Illuminates when the fuel cap is not CHECK installed correctly. Check the fuel FUEL cap for proper installation. When CAP the fuel filler cap is properly re-installed, the light(s) will turn off after a period of normal driving. Continuing to operate the vehicle with the check fuel cap light on, or a mis-installed fuel cap can activate the Service Engine Soon/Check Engine warning light.
Instrument Cluster Door ajar Illuminates when any door is open (or not fully closed). DOOR AJAR Anti-theft system (if equipped) Refer to SecuriLock娂 passive anti-theft system in the Locks and Security chapter. Four wheel drive high (if equipped) Illuminates when four-wheel drive is put in high range. If the light continues to flash have the system serviced. Four wheel drive high (if equipped) Illuminates when four-wheel drive is put in high range. If the light continues to flash have the system serviced.
Instrument Cluster Headlamps on warning chime Sounds when the headlamps or parking lamps are on, the key is removed from the ignition and the driver’s door is opened. Key-in-ignition warning chime Sounds when the key is left in the ignition and the driver’s door is opened. GAUGES Engine coolant temperature gauge Indicates the temperature of the engine coolant. At normal operating temperature, the needle remains within the normal area (the area between the “H” and “C”).
Instrument Cluster NOTE: This gauge indicates the temperature of the engine coolant, not the coolant level. If the coolant is not at its proper level the gauge indication will not be accurate. Engine oil pressure gauge Indicates engine oil pressure. At normal operating temperature, the needle will be in the normal range (the area between the “L” and “H”); H if the needle goes below the normal range, stop the vehicle as soon as L safely possible and switch off the engine immediately. Check the oil level.
Instrument Cluster Speedometer Indicates the current vehicle speed. Odometer Registers the total kilometers (miles) of the vehicle. Trip odometer Registers the kilometers (miles) of individual journeys. To reset, depress the control. 50 40 60 70 80 0 0 0 80 100 60 30 20 10 40 20 MPH 90 120 140 000000 160 100 180 110 km/h 120 Tachometer Indicates the engine speed in revolutions per minute. Driving with your tachometer pointer continuously at the top of the scale may damage the engine.
Entertainment Systems AM/FM STEREO VOL PUSH ON TONE TONE VOL ST SEEK DX FM 12 TUNE CLK 1 2 Volume/power control Press the control to turn the audio system on or off. Turn the control to raise or lower volume. 3 4 AM/FM VOL PUSH ON VOL PUSH ON If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on.
Entertainment Systems AM/FM select The AM/FM select control works in radio mode. AM/FM AM/FM select in radio mode This control allows you to select AM or FM frequency bands. Press the control to switch between AM, FM1 or FM2 memory preset stations. Tune adjust The tune control works in radio mode. Tune adjust in radio mode to move to the next • Press frequency down the band (whether or not a listenable station is located there). Hold the control to move through the frequencies quickly.
Entertainment Systems Radio station memory preset 1 2 3 4 The radio is equipped with four station memory preset controls. These controls can be used to select up to four preset AM stations and eight FM stations (four in FM1 and four in FM2). Setting memory preset stations 1. Select the frequency band with the AM/FM select control. 2. Select a station. Refer to Tune adjust or Seek function for more information on selecting a station. 3.
Entertainment Systems Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers. Press the TONE control three times, then use the volume knob to adjust the desired level. Setting the clock Press CLK to toggle between listening frequencies and clock mode. To set the hour, press and hold the CLK control until CLOCK SET appears in the display and press the SEEK control: • to decrease hours and • to increase hours.
Entertainment Systems when the radio is turned on, and then revert to clock information. Any time that the media is changed, (new radio station, etc.), the media information will again display for ten seconds before reverting back to the clock. In media mode, the media information will always be displayed.
Entertainment Systems Turn the control to raise or lower volume. VOL - PUSH ON If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on. AM/FM select The AM/FM select control works in radio and CD modes. AM FM CD AM/FM select in radio mode This control allows you to select AM or FM frequency bands. Press the control to switch between AM, FM1 or FM2 memory preset stations.
Entertainment Systems Tune adjust for CD changer (if equipped) to select the previous • Press SEEK disc in the CD changer. (Play will begin on the first track of the TUNE DISCS disc unless the CD changer is in shuffle mode. Refer to Shuffle feature for more information. Hold the control to continue reversing through the disc. to select the next disc in the CD changer. Hold the control • Press to fast-forward through the remaining discs. Seek function The seek function control works in radio or CD mode.
Entertainment Systems Scan function in CD mode Press SCN to hear a short sampling of all selections on the CD. (The CD scans in a forward direction, wrapping back to the first track at the end of the CD.) To stop on a particular selection, press the control again. Radio station memory preset The radio is equipped with four or six station memory preset controls.
Entertainment Systems Treble adjust The treble adjust control allows you to increase or decrease the audio system’s treble output. TREB Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers. BAL Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers. FADE CD select • To begin CD play (if CD[s] are loaded), press the CD control. The first track of the disc will begin playing.
Entertainment Systems Do not insert any promotional (odd shaped or sized) discs, or discs with removable labels into the CD player as jamming may occur. Rewind The rewind control works in CD and CD changer (if equipped) modes. To rewind in CD mode press the CD CD control (preset 1). 1 Pressing the control for less than three seconds results in slow rewind. Pressing the control for more than three seconds results in fast rewind. Fast forward The fast forward control works in CD mode.
Entertainment Systems Setting the clock Press CLK to toggle between listening frequencies and clock mode while in radio mode. To set the hour, press and hold the CLK control. SCN CLK Press the SEEK control: • to decrease hours and • to increase hours. SEEK TUNE DISCS To set the minute, press and hold the CLK control. SCN CLK Press the TUNE control: • to decrease minutes and • to increase minutes.
Entertainment Systems MACH姞 MP3 MUSIC SYSTEM 1. ON/OFF and volume control 2. AM/FM control 3. Bass control 4. Treble control 5. Fade control 6. Balance control 7. Seek control 8. Scan control 9. Clock control 10. Tune/Directory control 11. 12. 13. 14. 15. 16. 17. 18. 19.
Entertainment Systems Volume/power control Press the control to turn the audio system on or off. Turn the control to raise or lower the volume. If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on. AM/FM select The AM/FM select control works in radio mode. AM/FM select in radio mode This control allows you to select AM or FM frequency bands.
Entertainment Systems When a radio frequency is in tune, the ST icon will appear in the display for stereo broadcasts. MP3 functions Your audio system is equipped with MP3 capability which allows you to listen to songs in MP3 flat file mode and MP3 directory mode. To engage MP3 flat file mode, insert an MP3 disc. If an MP3 disc is already present in the player, press the CD control. The MP3 icon will display while the player is in MP3 mode.
Entertainment Systems Seek function in radio mode to find the next • Press listenable station down the frequency band. to find the next • Press listenable station up the frequency band. Seek function in CD, MP3 flat file and MP3 directory modes to select and play the • Press previous track on the disc. If the current track is the first track on will select the disc, pressing the last track on the disc. to select and play the • Press next track on the disc.
Entertainment Systems Scan function in CD mode Press SCN to engage scan mode and to hear a brief sampling of all tracks on the disc. The track number in the display will blink while the scan function is enabled. When the end of the disc is reached, the player will continue to scan from the first track forward. Press SCN again to disengage scan mode. Scan function in MP3 flat file mode The scan function in MP3 flat file mode allows you to briefly audition all tracks on the MP3 disc.
Entertainment Systems Radio station memory preset The radio is equipped with six station memory preset controls. These controls can be used to select up to six preset AM stations and twelve FM stations (six in FM1 and six in FM2). Setting memory preset stations 1. Select the frequency band with the AM/FM select control. 2. Select a station. Refer to Tune adjust or Seek function for more information on selecting a station. 3.
Entertainment Systems Bass adjust The bass adjust control allows you to increase or decrease the audio system’s bass output. Treble adjust The treble adjust control allows you to increase or decrease the audio system’s treble output. Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers. Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers. CD select The CD select function allows you to play CDs.
Entertainment Systems Playing a CD • If a CD is already loaded, press the CD control. CD play will begin where it stopped last. • If a CD is not already loaded, insert the CD into the system. CD will briefly appear in the display and then the first track on the disc will begin playing. Playing an MP3 disc in MP3 flat file mode and MP3 directory mode • Insert an MP3 disc into the player. CD and LOAD will appear in the display.
Entertainment Systems current directory is the last directory on the disc, pressing will select the first directory on the disc. Press and hold for fast selection. • Press on TUNE DIR to revert to the previous directory on the MP3 disc. If the current directory is the first directory on the disc, pressing will select the last directory on the disc. Press and hold for fast selection. Eject function Press the control to stop and eject a disc.
Entertainment Systems Compression adjust brings soft and loud CD passages together for a more consistent listening level. Press the COMP control to activate compression adjust. The compression icon (c) will illuminate in the display while the compression function is enabled. Press the COMP control again to disengage the feature. Shuffle feature The shuffle feature works in CD mode, MP3 flat file mode and MP3 directory mode.
Entertainment Systems • Press the SHUFFLE control to engage random play. SHF and then ON will briefly appear in the display. The player will then begin random play. • To select another random track or on on the disc, press the SEEK control. • Press SCN to scan through random tracks. The track number will flash in the display. The shuffle function will remain enabled. • Press SHUFFLE again to disengage the shuffle feature. SHF and then OFF will briefly display and the current track will continue to play.
Entertainment Systems • Press the SCN control to scan through random tracks in the current directory. The track number will flash in the display. The shuffle feature will remain enabled. To shuffle tracks in another directory, press or on the TUNE DIR control to select the desired directory. The shuffle function still remains enabled. Press the SHUFFLE control again to disengage the SHUFFLE feature. SHUF and OFF will briefly display and the current track will continue to play.
Entertainment Systems Repeat track function in MP3 flat file mode and MP3 directory mode. Press the REPEAT control to repeat the current track. The repeat icon will display and the current track will continue to repeat until the repeat function is disengaged. Press the REPEAT control again to disengage the feature. Error messages You may experience an error message for the following situations: • NO DISC when the CD control is pressed and there is not a CD present.
Entertainment Systems Saving and naming MP3 files • Your MACH威 MP3 music system supports discs containing up to 255 files in 255 directories. Discs containing more than 255 files will not play. • Always save MP3 files with the .mp3 extension. The player recognizes an MP3 file by the .mp3 extension, so MP3 files saved with different extensions will not be played. Never save a non-MP3 file with the .mp3 extension as the file will not play properly and damage may occur to the player or your sound system.
Entertainment Systems This hierarchy is an example of a more complex directory structure. While you are capable of setting up many directory levels when burning a CD, the MACH威 MP3 music system will display the structure as if it were only one level deep. Therefore, the system will condense the complex hierarchy into a structure similar to the one-level-deep example above. This will not harm the MP3 disc and will not change the hierarchy that is actually written on the disc.
Entertainment Systems Volume/power control Press the control to turn the audio system on or off. Audio power can also be turned on by pressing the AM/FM select control or the TAPE/CD select control. VOL - PUSH ON Turn control to raise or lower volume. VOL - PUSH ON If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on.
Entertainment Systems • Press to move to the next frequency up the band (whether or not a listenable station is located there). Hold for quick movement. Seek function The seek function control works in radio, tape or CD mode. Seek function in radio mode • Press to find the next listenable station down the frequency band. • Press to find the next listenable station up the frequency band. Seek function in tape mode • Press to listen to the previous selection on the tape.
Entertainment Systems Radio station memory preset The radio is equipped with six station memory preset controls. These controls can be used to select up to six preset AM stations and twelve FM stations (six in FM1 and six in FM2). Setting memory preset stations 1. Select the frequency band with AM FM the AM/FM select control. 2. Select a station. Refer to Tune adjust or Seek function for more information on selecting a station. 3.
Entertainment Systems Bass adjust The bass adjust control allows you to increase or decrease the audio system’s bass output. BASS TREB Press the BASS control then press: • to decrease the bass output and • to increase the bass output. Treble adjust The treble adjust control allows you to increase or decrease the audio system’s treble output. Press the TREB control then press: • BASS TREB to decrease the treble output and • to increase the treble output.
Entertainment Systems Tape/CD select • To begin tape play (with a tape loaded into the audio system) TAPE CD while in the radio or CD mode, press the TAPE control. Press the button during rewind or fast forward to stop the rewind or fast forward function. • To begin CD play (if CD is loaded), press the CD control. TAPE CD The first track of the disc will begin playing. If returning from radio or tape mode, CD play will begin where it stopped last. Rewind The rewind control works in tape REW and CD modes.
Entertainment Systems Eject function Press the EJ control to stop and eject a tape. EJ Press the EJ control to stop and eject a CD. EJ Dolby姞 noise reduction Dolby威 noise reduction operates in tape mode. Dolby威 noise reduction reduces the amount of hiss and static during tape playback. Press the reduction. 4 control to activate (and deactivate) the Dolby威 noise Dolby威 noise reduction is manufactured under license from Dolby威 Laboratories Licensing Corporation.
Entertainment Systems Setting the clock To set the hour, press and hold the CLK control and press SEEK: AUTO CLK • to decrease hours and • to increase hours. To set the minute, press and hold the CLK control and press TUNE: AUTO CLK • to decrease minutes and • to increase minutes. If your vehicle has a separate clock, (other than the digital radio display), the CLK control will not function in the above manner.
Entertainment Systems Mute mode Press the MUTE control to mute the playing media. Press the MUTE control again to return to the playing media. EJ MUTE TREMOR II AUDIO SYSTEM 1. 2. 3. 4. 5. 6. 7. 8. Mute control Tape control CD control Tune control Seek/scan control Eject control (tape) Balance/fade control Compression/shuffle control 9. Tape direction/Dolby威 control 10. Select control 11. Rewind/fast forward control 12. Bass/treble control 13. Volume/on/off control 14. Auto/RDS control 15.
Entertainment Systems Volume/power control Press the control to turn the audio system on or off. Turn control to raise or lower volume. VOL PUSH ON If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on. If you wish to maintain your preset volume level, turn the audio system off with the power control before switching off the ignition.
Entertainment Systems Tune adjust in radio mode to move to the next • Press frequency down the band (whether or not a listenable station is located there). Hold the control to move through the frequencies quickly. to move to the next frequency up the band (whether or not • Press a listenable station is located there). Hold for quick movement. Seek function The seek function control works in radio, tape or CD mode.
Entertainment Systems Scan function The scan function works in radio, tape or CD mode. Scan function in radio mode Press the SCAN control to hear a brief sampling of all listenable stations on the frequency band. Press the control again to stop the scan mode. Scan function in tape mode Press the SCAN control to hear a short sampling of all selections on the tape. (The tape scans in a forward direction. At the end of the tape’s first side, direction automatically reverses to the opposite side of the tape.
Entertainment Systems Press the TREB control then press: • to decrease treble output and • to increase treble output. Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers. Press the BAL control then press: • to shift sound to the left and • to shift sound to the right. Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers.
Entertainment Systems Autoset memory preset Autoset allows you to set strong radio stations without losing your original manually set preset stations. This feature is helpful on trips when you travel between cities with different radio stations. Starting autoset memory preset 1. Select a frequency using the AM/FM select controls. 2. Press the AUTO control. CLK 3. When the first six strong stations AUTO RDS are filled, the station stored in memory preset control 1 will start playing.
Entertainment Systems Rewind The rewind control works in tape and CD modes. • In tape mode, radio play will continue until rewind is stopped (with the TAPE control) or the beginning of the tape is reached. • In CD mode, pressing the REW control for less than three seconds results in slow rewind. Pressing the control for more than three seconds results in fast rewind. Fast forward The fast forward control works in tape and CD modes.
Entertainment Systems Dolby姞 noise reduction Dolby威 noise reduction operates only in tape mode. Dolby威 noise reduction reduces the amount of hiss and static during tape playback. Press the control to activate (and deactivate) Dolby威 noise reduction. Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories. Compression adjust Compression adjust brings soft and loud CD passages together for a more consistent listening level.
Entertainment Systems Use the SEL control to enable (ON) or disable (OFF) the feature. RDS traffic announcement When set ON, this traffic feature will interrupt tape or CD play to play a traffic report broadcast from a FM RDS station. To activate the traffic feature: CLK AUTO RDS • Press the RDS control until TRAFFIC is displayed. To see if any stations in your area are capable of broadcasting an RDS traffic alert, press SCAN or SEEK while TRAFFIC ON is displayed.
Entertainment Systems RDS show RDS sends information with the FM broadcast, including: station name, station type, and/or radio text. To view this information: • With the RDS menu enabled, CLK press the RDS control until AUTO RDS SHOW is displayed. • Use the SEL control to select TYPE, NAME, TEXT or NONE. When your radio is turned to a RDS station, RDS station TYPE, station NAME, or TEXT message will be displayed along with the frequency. Press SEL in order to scroll through the text messages.
Entertainment Systems PREMIUM AM/FM STEREO IN DASH SIX CD RADIO SHUF DISC TUNE SCAN SEEK REW FF COMP MUTE EJ LOAD BASS BAL SEL TREB FADE PUSH ON AM FM CD 1 2 3 4 5 6 MENU Volume/power control Press the control to turn the audio system on or off. Turn the control to raise or lower volume. PUSH ON If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on.
Entertainment Systems Tune adjust in radio mode to move to the next • Press DISC TUNE frequency down the band (whether or not a listenable station is located there). Hold the control to move through the frequencies quickly. to move to the next frequency up the band (whether or not • Press a listenable station is located there). Hold for quick movement. Disc adjust for CD mode to select the previous • Press DISC TUNE disc. (Play will begin on the first track of the disc unless shuffle mode is engaged.
Entertainment Systems Scan function The scan function works in radio or CD mode. Scan function in radio mode Press the SCAN control to hear a brief sampling of all listenable stations on the frequency band. Press the SCAN control again to stop the scan mode. Scan function in CD mode Press the SCAN control to hear a short sampling of all selections on the CD. (The CD scans in a forward direction, wrapping back to the first track at the end of the CD.
Entertainment Systems Starting autostore 1. Press and momentarily hold the AM/FM control. 2. AUTOSET will flash in the display AM CD as the frequency band is scrolled FM through. 3. When the six strongest stations are filled, the station stored in memory preset control 1 will start playing. If there are fewer than six strong stations available on the frequency band, the remaining memory preset controls will all store the last strong station available.
Entertainment Systems Display description Six circles are always lit in the digital display. These signify the six CD slots in the audio system. When a disc is loaded into a particular slot (1–6), the number inside that specific circle lights. If the circle is empty, there is no CD in that particular slot. Load The load feature allows you to load LOAD single CDs into the player internal to the radio. This six disc CD player is equipped with a CD door.
Entertainment Systems CD 2, press the EJ control and then press the preset 2 control. If you do not choose a specific CD, the player will eject the current CD. If a CD is ejected and not removed from the door of the CD player, the player will automatically reload the CD. This feature may be used when the ignition is ON or OFF. Auto eject Press and momentarily hold the EJ EJ control to engage auto eject. All CDs which are present in the player will be ejected one at a time.
Entertainment Systems SHUFFLE DISC randomly plays tracks from all the discs presently in the audio system. SHUFFLE TRK plays all the tracks on the current disc in random order. Compression feature The compression feature operates in CD mode and brings soft and loud CD passages together for a more consistent listening level. Press the COMP control until COMP ON is displayed. Bass adjust The bass adjust control allows you to increase or decrease the audio system’s bass output. Press the BASS control.
Entertainment Systems Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers. Press the FADE control. Use the SEL control to adjust the sound between the front and rear speakers. BAL + SEL FADE Menu mode The MENU control allows you to access many different features within your audio system. There are three sets of menus available depending upon which mode or feature is activated. While in FM mode, two menus are available.
Entertainment Systems SHOW — Allows you to select from NAME (displays the name of the radio station), TYPE (displays the RDS program type: rock, jazz, etc.), or NONE (deactivates the RDS display). Traffic announcements This feature allows you to hear traffic announcements. When in this MENU + SEL mode, traffic announcements will interrupt radio and CD play. When in FM mode and RDS is activated, press the MENU until TRAFFIC OFF displays. Press the SEL control to engage the feature.
Entertainment Systems Radio data system (RDS) feature This feature allows your audio system to receive text information MENU + SEL from RDS-equipped FM radio stations. To activate RDS: • When in FM mode, press the MENU control until RDS OFF displays. • Press the SEL control to engage this feature (RDS ON). RDS features: Once the RDS feature is on, press the MENU control to scroll through the following selections: Traffic announcements This feature allows you to hear traffic announcements while in CD mode.
Entertainment Systems • Classic • Country • Info • Jazz • Oldies Show This feature allows you to select the type of RDS broadcast information the radio will regularly show in the display. • • • • • R&B Religious Rock Soft Top 40 MENU + SEL With RDS activated, press the MENU control until SHOW is MENU + SEL displayed. Use the SEL control to select TYPE (displays the RDS program type: rock, jazz, etc), NAME (displays the name of the radio station) or NONE (deactivates the RDS display).
Entertainment Systems CLEANING COMPACT DISCS Inspect all discs for contamination before playing. If necessary, clean discs only with an approved CD cleaner and wipe from the center out to the edge. Do not use circular motion. MP3 DISC QUALITY FACTORS The MACH威 MP3 music system is designed for use with CD-DA (regular audio discs), CD-R and CD-RW discs. Discs must comply with ISO 9660 and Joliet standards.
Entertainment Systems • Use care when handling and playing CD-R and CD-RW discs, which are more susceptible to damage from heat, light and stress than are regular CDs. • Always insert and remove a disc by holding the disc flat, with the playing surface facing down, in order to prevent damage to the disc or the player. • Never insert any object other than a compact disc into the player, as doing so may damage the player and may cause injury to you. • Do not disassemble the player.
Entertainment Systems RADIO FREQUENCY INFORMATION The Federal Communications Commission (FCC) and the Canadian Radio and Telecommunications Commission(CRTC) establish the frequencies AM and FM stations may use for their broadcasts. Allowable frequencies are: AM 530, 540–1600, 1610 kHz FM 87.7, 87.9–107.7, 107.9 MHz Not all frequencies are used in a given area. RADIO RECEPTION FACTORS Three factors can affect radio reception: • Distance/strength. The further an FM signal travels, the weaker it is.
Climate Controls HEATER ONLY SYSTEM (IF EQUIPPED) Fan speed control Controls the volume of air circulated in the vehicle. Temperature control knob Controls the temperature of the airflow inside the vehicle. On heater-only systems, the air cannot be cooled below the outside temperature. Mode selector control Controls the direction of the airflow to the inside of the vehicle. • (Panel) – Distributes outside air through the instrument panel registers.
Climate Controls Operating tips ) • In humid weather, place the climate control system in Defrost ( before driving. This will reduce fogging on your windshield. Once the windshield has been cleared, select any desired position. • To reduce humidity buildup inside the vehicle, do not drive with the climate control system in the OFF position. • Under normal weather conditions, your vehicle’s climate control system should be left in any position other than OFF position when the vehicle is parked.
Climate Controls Fan speed control Controls the volume of air circulated in the vehicle. Temperature control knob Controls the temperature of the airflow inside the vehicle. Mode Selector Control Controls the direction of the airflow to the inside of the vehicle. OFF A/C MAX A/C The air conditioning compressor can operate in all modes except and . However, the air conditioning will only function if the outside temperature is about 6°C (43°F) or higher.
Climate Controls • OFF – Outside air is shut out and the fan will not operate. For short periods of time only, use this mode to prevent undesirable odors from entering the vehicle. • (Panel and floor) – Distributes outside air through the instrument panel registers and the floor ducts. Heating and air conditioning capabilities are provided in this mode.
Climate Controls • Under snowy or dirty weather conditions, your vehicle’s climate control system should be left in the OFF position when the vehicle is parked. This allows the climate control system to be free from contamination of outside pollutants. • If your vehicle has been parked with the windows closed during warm weather conditions, the air conditioner will perform more efficiently in cooling the vehicle if driven for two or three minutes with the windows open.
Lights HEADLAMP CONTROL Rotate the headlamp control to the first position to turn on the parking lamps. Rotate to the second position to turn on the headlamps. OFF Foglamp control (if equipped) The foglamps can be turned on when the headlamp control is in either of the following positions: • Parking lamps • Low beams Press the foglamp control to activate the foglamps. Press the foglamp control again to deactivate the foglamps. When the highbeams are activated, the foglamps will not operate.
Lights High beams Push the lever toward the instrument panel to activate. Pull the lever towards you to deactivate. Flash to pass Pull toward you slightly to activate and release to deactivate. PANEL DIMMER CONTROL Use to adjust the brightness of the instrument panel and all applicable switches in the vehicle during headlamp and parklamp operation. Move the control to the full upright position, past detent, to turn on the interior lamps.
Lights TURN SIGNAL CONTROL • Push down to activate the left turn signal. • Push up to activate the right turn signal. INTERIOR LAMPS COURTESY/READING LAMPS (IF EQUIPPED) The courtesy lamp lights when: • any door is opened. • the instrument panel dimmer switch is held up until the courtesy lamps come on. • the remote entry controls are pressed and the ignition is OFF. The reading lamps can be turned on by moving the switch on the dome lamp to either the left or the right.
Lights Using the right bulbs Replacement bulbs are specified in the chart below. Headlamp bulbs must be marked with an authorized “D.O.T.” for North America and an “E” for Europe to assure lamp performance, light brightness and pattern and safe visibility. The correct bulbs will not damage the lamp assembly or void the lamp assembly warranty and will provide quality bulb burn time.
Lights Replacing headlamp bulbs To remove the headlamp bulb: 1. Make sure headlamp switch is in OFF position, then open the hood. 2. Remove two screws and cover (if equipped). 3. At the back of the headlamp, pry up the two retainer pins to release the headlamp assembly from the vehicle and pull headlamp forward. 4. Disconnect the electrical connector from the bulb by pulling rearward. 5.
Lights To install the new bulb: Handle a halogen headlamp bulb carefully and keep out of children’s reach. Grasp the bulb only by its plastic base and do not touch the glass. The oil from your hand could cause the bulb to break the next time the headlamps are operated. 1. With the flat side of the bulb’s plastic base facing upward, insert the glass end of the bulb into the lamp assembly. You may need to turn the bulb left or right to align the grooves in the plastic base with the tabs in the lamp assembly.
Lights 4. Remove screw(s) from lamp assembly and disengage lamp assembly (it has a snap fit). 5. Rotate bulb socket counterclockwise and remove from lamp assembly. 6. Carefully pull bulb straight out of socket and push in the new bulb. 7. Install the bulb socket in lamp assembly by turning clockwise. Install the new lamp in reverse order.
Lights Replacing tail lamp/backup lamp bulbs The tail lamp/backup lamp bulbs are located in the same portion of the tail lamp assembly, one just below the other. Follow the same steps to replace either bulb: 1. Open the tailgate to expose the lamp assemblies. 2. Remove the four screws and the lamp assembly from vehicle. 3. Rotate bulb socket counterclockwise turn and remove from lamp assembly. 4. Carefully pull the bulb straight out of the socket and push in the new bulb. 5.
Lights Replacing high-mount brakelamp and cargo lamp bulbs The replacement of the high-mount brakelamp bulb and cargo lamp bulb is basically the same. This procedure covers the high-mount brakelamp bulb. To remove the brakelamp assembly: 1. Remove the two screws and lamp assembly from vehicle. 2. Remove the bulb socket from lamp assembly by rotating it counterclockwise. 3. Carefully pull bulb straight out of socket and push in the new bulb. To install the brakelamp assembly: 1.
Driver Controls WINDSHIELD WIPER/WASHER CONTROLS Rotate the windshield wiper control to the desired interval, low or high speed position. The bars of varying length are for intermittent wipers. When in this position rotate the control upward for fast intervals and downward for slow intervals. Push (tap) the end of the stalk briefly for a single swipe (no wash). Push and hold for three swipes with wash. Push and hold for a longer wash (up to ten seconds).
Driver Controls Changing the wiper blades To replace the wiper blades: 1. Pull the wiper arm away from the windshield and lock into the service position. 2. Turn the blade at an angle from the wiper arm. Push the lock pin manually to release the blade and pull the wiper blade down toward the windshield to remove it from the arm. 3. Attach the new wiper to the wiper arm and press it into place until a click is heard.
Driver Controls Never adjust the steering wheel when the vehicle is moving. AUXILIARY POWER POINT SEEK 12V TUNE 1 2 3 4 AM-FM OFF A/C MAX A/C Power outlets are designed for accessory plugs only. Do not hang any type of accessory or accessory bracket from the plug. Improper use of the power outlet can cause damage not covered by your warranty. The auxiliary power point is located on the instrument panel.
Driver Controls POWER WINDOWS (IF EQUIPPED) Press and hold the rocker switches to open and close windows. • Press the top portion of the rocker switch to close. AUTO • Press the bottom portion of the rocker switch to open. AUTO One touch down • Press AUTO completely down and release quickly. The driver’s window will open fully. Depress again to stop window operation. One touch down can be deactivated during operation by pushing down on the top part of the driver power window control.
Driver Controls POWER SIDE VIEW MIRRORS (IF EQUIPPED) To adjust your mirrors: to adjust the left 1. Select to adjust the right mirror or mirror. 2. Move the control in the direction you wish to tilt the mirror. 3. Return to the center position to lock mirrors in place. SPEED CONTROL (IF EQUIPPED) To turn speed control on • Press ON. Vehicle speed cannot be controlled until the vehicle is traveling at or above 48 km/h (30 mph). Do not shift the gearshift lever into N (Neutral) with the speed control on.
Driver Controls To turn speed control off • Press OFF or • Turn off the vehicle ignition. Once speed control is switched off, the previously programmed set speed will be erased. ON OFF To set a speed • Press SET ACC. For speed control to operate, the speed control must be ON and the vehicle speed must be greater than 48 km/h (30 mph). RSM SET ACC COAST If you drive up or down a steep hill, your vehicle speed may vary momentarily slower or faster than the set speed. This is normal.
Driver Controls To set a higher set speed • Press and hold SET ACC. Release the control when the desired vehicle speed is reached or • Press and release SET ACC to operate the Tap-Up function. Each press will increase the set speed by 1.6 km/h (1 mph) or • Accelerate with your accelerator pedal. When the desired vehicle speed is reached, press and release SET ACC. RSM SET ACC COAST You can accelerate with the accelerator pedal at any time during speed control usage.
Driver Controls To disengage speed control • Depress the brake pedal or • Depress the clutch pedal (if equipped). Disengaging the speed control will not erase the previously programmed set speed. Fully depressing the clutch pedal may cause a flare in engine RPM as the throttle is returned to idle. This is normal. Pressing OFF will erase the previously programmed set speed.
Driver Controls To return to a previously set speed • Press RSM. For RSM to operate, the vehicle speed must be faster than 48 km/h (30 mph). RSM SET ACC COAST Indicator light This light comes on when either the SPEED SET ACCEL or RES controls are pressed. It turns off when the speed CONT control OFF control is pressed, the brake or clutch is applied or the ignition is turned to the OFF position.
Driver Controls For additional information about the gearshift lever and the transmission control switch operation refer to the Automatic Transmission Operation section of the Driving chapter. CENTER CONSOLE (IF EQUIPPED) Your vehicle may be equipped with a variety of console features. These include: • Utility compartment with cassette/compact disc storage • Cupholders • Coin holder slots • Flip up armrest Use only soft cups in the cupholder. Hard objects can injure you in a collision.
Driver Controls To extend the bed extender: 1. Lower tailgate. 2. Pull the round knobs on each side of the extender to release it from the pickup box. 3. Pivot extender on to the tailgate. 4. Evenly push down on the extender and push the round knobs in on each side locking it in place. Green markings on the shaft indicate the locked position. The locking clip screws below the middle bar can be tightened counterclockwise for extra security.
Driver Controls The bed extender should always be kept in the stowed position with the tailgate closed when not in use. To remove the bed extender: 1. Extend the bed extender. 2. Pull the round knobs on each side of the extender to unlock it. Make sure the locking clip screws are loose before removing the extender. 1. Press the locking clips below the middle bar on each side and lift the extender out of the bed. To install the bed extender, follow the removal procedure in reverse order.
Driver Controls • Raise the tailgate and close securely. • Lower the tonneau on to the pickup box to lock the tailgate. TONNEAU COVER (IF EQUIPPED) The tonneau cover has been designed to maximize fuel economy and should be fully installed whenever possible. The rear panel can be folded in half and secured behind the cab, or the whole cover can be removed completely from the vehicle. To avoid damage to the cover, do not operate the vehicle unless the cover is fully installed, or securely stowed.
Driver Controls To stow the rear panel: • Before driving with the tonneau cover open, stow the rear panel. • Release two cylinder clips and disconnect the hydraulic cylinders from the pickup box and secure them in the clips on the panel. • Lift the rear panel up, lay it on top of the front panel and secure it to the hooks on the front panel with the tiedown cords. Failure to secure the rear panel could damage the tonneau cover or vehicle.
Driver Controls The cargo divider is designed to divide your pickup box in half or rotate 90° to allow you full use of the pickup box. To rotate the cargo divider 90°: • Open front panel. • Pull the lower release lever out on each side of the cargo divider to unlatch from the pickup box. • Rotate the divider 90° parallel with the tonneau cover and secure it to the pickup box with the lower release levers. To rotate the cargo divider back, follow the procedure in reverse order.
Driver Controls To remove the tonneau cover: The tonneau cover needs to be supported during removal. This is a two person operation. • Remove the cargo divider, refer to To remove the cargo divider in this procedure. • Open and support the front panel. • Release two cylinder clips and disconnect the hydraulic cylinders from the pickup box and secure them in the clips on the front panel. Close the front panel. • Stow the rear panel on top of the front panel, refer to To stow the rear panel in this procedure.
Locks and Security KEYS The key operates all locks on your vehicle. In case of loss, replacement keys are available from your dealer. You should always carry a second key with you in a safe place in case you require it in an emergency. Refer to SecuriLock娂 Passive Anti-Theft System for more information. POWER DOOR LOCKS (IF EQUIPPED) If the door does not unlock when the top of the control is pressed, see Interior power door unlock disable feature in the Remote entry section in this chapter.
Locks and Security Keep vehicle doors and tonneau cover locked and keep keys and remote transmitters out of a child’s reach. Unsupervised children could lock themselves in the box and risk injury. Children should be taught not to play in vehicles. On hot days, the temperature in the pickup box can rise very quickly. Exposure of people or animals to these high temperatures for even a short time can cause death or serious heat-related injuries, including brain damage. Small children are particularly at risk.
Locks and Security Unlocking the doors Press this control to unlock the driver’s door. The interior lamps will illuminate. Press the control a second time within five seconds to unlock all doors. Locking the doors Press this control to lock all doors. To confirm all doors are closed and locked, press the control a second time within five seconds. The doors will lock again, the horn will chirp and the lamps will flash.
Locks and Security Sounding a panic alarm Press this control to activate the alarm. To deactivate the alarm, press the control again or turn the ignition to ACC or ON. Panic alarm will only operate with the ignition in the OFF position. Replacing the battery The transmitter is powered by one coin type three-volt lithium battery CR2032 or equivalent. Typical operating range will allow you to be up to 10 meters (33 feet) away from your vehicle.
Locks and Security Replacing lost transmitters If a remote transmitter has been lost and you would like to remove it from the vehicle’s memory, or you would like to purchase additional remote transmitters and have them programmed to your vehicle: • Take all your vehicle’s transmitters to your dealer for programming, or • Perform the programming procedure yourself.
Locks and Security Illuminated entry The interior lamps illuminate when the remote entry system is used to unlock the door(s) or sound the personal alarm. The system automatically turns off after 25 seconds or when the ignition is turned to the RUN or ACC position. The dome lamp control (if equipped) must not be set to the OFF position for the illuminated entry system to operate. The inside lights will not turn off if: • they have been turned on with the dimmer control, or • any door is open.
Locks and Security Automatic arming The vehicle is armed immediately after switching the ignition to the 3 (OFF) position. The THEFT indicator in the instrument cluster will flash every two seconds when the vehicle is armed. 4 3 5 2 1 Automatic disarming Switching the ignition to the 4 (ON) position with a coded key disarms the vehicle. The THEFT indicator will illuminate for three seconds and then go out.
Locks and Security If your keys are lost or stolen you will need to do the following: • Use your spare key to start the vehicle, or • Have your vehicle towed to a dealership or a locksmith. The key codes will need to be erased from your vehicle and new key codes will need to be re-coded. Replacing coded keys can be very costly and you may want to store an extra programmed key away from the vehicle in a safe place to prevent an unforeseen inconvenience. The correct coded key must be used for your vehicle.
Locks and Security 4. Turn the ignition to 3 (OFF) then 2 (LOCK) and remove the second coded key from the ignition. 5. Within 20 seconds of removing the second coded key, insert the new unprogrammed key (new key/valet key) into the ignition and turn the ignition from 3 (OFF) to 4 (ON) (maintain ignition in 4 (ON) for at least one second). This step will program your new key to a coded key. 6. To program additional new unprogrammed key(s), repeat this procedure from step 1.
Seating and Safety Restraints SEATING Adjusting the front manual seat Never adjust the driver’s seat or seatback when the vehicle is moving. Do not pile cargo higher than the seatbacks to reduce the risk of injuring people in a collision or sudden stop. Always drive and ride with your seatback upright and the lap belt snug and low across the hips. Reclining the seatback can cause an occupant to slide under the seat’s safety belt, resulting in severe personal injuries in the event of a collision.
Seating and Safety Restraints Using the manual lumbar support (if equipped) Turn the lumbar support control clockwise to increase firmness. Turn the lumbar support control counterclockwise to increase softness. REAR SEATS Center facing jump seat (2 door SuperCab) (if equipped) To open, pull inboard and down on the seat handle. To stow the seat, pull seat bottom back to the fully upright position. Do not install a child seat in a center facing jump seat.
Seating and Safety Restraints To reduce the risk of injury, make sure children sit where they can be properly restrained. Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from injury in a collision. All occupants of the vehicle, including the driver, should always properly wear their safety belts, even when an air bag (SRS) is provided. It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle.
Seating and Safety Restraints Combination lap and shoulder belts 1. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) until you hear a snap and feel it latch. Make sure the tongue is securely fastened in the buckle. 2. To unfasten, push the release button and remove the tongue from the buckle. The front outboard safety restraints in the vehicle are combination lap and shoulder belts.
Seating and Safety Restraints Automatic locking mode In this mode, the shoulder belt is automatically pre-locked. The belt will still retract to remove any slack in the shoulder belt. The automatic locking mode is not available on the driver safety belt. When to use the automatic locking mode • Any time a child safety seat is installed in a passenger front seat. Refer to Safety Restraints for Children, Safety Seats for Children, or Passenger air bag On/Off switch later in this chapter.
Seating and Safety Restraints How to disengage the automatic locking mode Disconnect the combination lap/shoulder belt and allow it to retract completely to disengage the automatic locking mode and activate the vehicle sensitive (emergency) locking mode.
Seating and Safety Restraints Front safety belt height adjustment Your vehicle has safety belt height adjustments for the driver and front passenger. Adjust the height of the shoulder belt so the belt rests across the middle of your shoulder. • Regular Cab and 4–door Super Cab • 2–door SuperCab To lower the shoulder belt height, push the button and slide the height adjuster down. To raise the height of the shoulder belt, slide the height adjuster up.
Seating and Safety Restraints Position the safety belt height adjusters so that the belt rests across the middle of your shoulder. Failure to adjust the safety belt properly could reduce the effectiveness of the seat belt and increase the risk of injury in a collision. Lap belts Adjusting the front center seat lap belt (if equipped) The lap belt does not adjust automatically. The lap belt should fit snugly and as low as possible around the hips, not across the waist.
Seating and Safety Restraints Adjusting the rear center facing jump seat lap belt (if equipped) The lap belt will adjust automatically. To fasten, grasp the tongue, and with a continuous motion, pull out enough webbing to buckle the tongue into the correct buckle. If you did not pull out enough webbing to reach the buckle, allow the tongue to retract fully before trying to pull it out again. The lap belt should fit snugly and as low as possible around the hips, not across the waist.
Seating and Safety Restraints Conditions of operation If... The driver’s safety belt is not buckled before the ignition switch is turned to the ON position... The driver’s safety belt is buckled while the indicator light is illuminated and the warning chime is sounding... The driver’s safety belt is buckled before the ignition switch is turned to the ON position... Then... The safety belt warning light illuminates 1-2 minutes and the warning chime sounds 4-8 seconds.
Seating and Safety Restraints The following are reasons most often given for not wearing safety belts: (All statistics based on U.S. data) Reasons given... “Crashes are rare events” “I’m not going far” “Belts are uncomfortable” “I was in a hurry” “Seat belts don’t work” “Traffic is light” “Belts wrinkle my clothes” “The people I’m with don’t wear belts” 124 Consider... 36700 crashes occur every day. The more we drive, the more we are exposed to “rare” events, even for good drivers.
Seating and Safety Restraints Reasons given... “I have an air bag” “I’d rather be thrown clear” Consider... Air bags offer greater protection when used with safety belts. Frontal airbags are not designed to inflate in rear and side crashes or rollovers. Not a good idea. People who are ejected are 40 times more likely to DIE. Safety belts help prevent ejection, WE CAN’T “PICK OUR CRASH”. Do not sit on top of a buckled safety belt to avoid the Belt Minder chime.
Seating and Safety Restraints BeltMinder activation and deactivation procedure 1. Turn the ignition switch to the RUN (or ON) position. (DO NOT START THE ENGINE.) 2. Wait until the safety belt warning light turns off. (Approximately 1–2 minutes.) • Steps 3–5 must be completed within 60 seconds or the procedure will have to be repeated. 3. Buckle then unbuckle the safety belt three times, ending with the safety belt unbuckled. This can be done before or during BeltMinder warning activation. 4.
Seating and Safety Restraints equipped), child safety seat tether bracket assemblies (if equipped), LATCH child seat tether anchors and lower anchors (if equipped), and attaching hardware, should be inspected after a collision. Ford Motor Company recommends that all safety belt assemblies used in vehicles involved in a collision be replaced.
Seating and Safety Restraints Important supplemental restraint system (SRS) precautions The supplemental restraint system is designed to work with the safety belt to help protect the driver and right front passenger from certain upper body injuries. Air bags DO NOT inflate slowly or gently and the risk of injury from a deploying air bag is greatest close to the trim covering the air bag module.
Seating and Safety Restraints Do not attempt to service, repair, or modify the Air Bag Supplemental Restraint System or its fuses. See your Ford or Lincoln Mercury dealer. The front passenger air bag is not designed to offer protection to an occupant in the center front seating position. Modifications to the front end of the vehicle, including frame, bumper, front end body structure and tow hooks may affect the performance of the air bag sensors increasing the risk of injury.
Seating and Safety Restraints How does the air bag supplemental restraint system work? The air bag SRS is designed to activate when the vehicle sustains sufficient longitudinal deceleration. The fact that the air bags did not inflate in a collision does not mean that something is wrong with the system. Rather, it means the forces were not of the type sufficient to cause activation. Air bags are designed to inflate in frontal and near-frontal collisions, not rollover, side-impact, or rear-impacts.
Seating and Safety Restraints If the air bag has deployed, the air bag will not function again and must be replaced immediately. If the air bag is not replaced, the unrepaired area will increase the risk of injury in a collision.
Seating and Safety Restraints Disposal of air bags and air bag equipped vehicles (including pretensioners) For disposal of air bags or air bag equipped vehicles, see your local dealership or qualified technician. Air bags MUST BE disposed of by qualified personnel. Passenger air bag ON/OFF switch An air bag ON/OFF switch has been installed in this vehicle. Before driving, always look at the face of the switch to be sure the switch is in the proper position in accordance with these instructions and warnings.
Seating and Safety Restraints In order to avoid inadvertent activation of the switch, always remove the ignition key from the passenger air bag ON/OFF switch. Turning the passenger air bag back on The passenger air bag remains OFF until you turn it back ON. 1. Insert the ignition key and turn the switch to ON. ON OFF 2. The OFF light will briefly illuminate when the ignition is OFF turned to ON. This indicates that the passenger air bag is operational.
Seating and Safety Restraints Always use safety belts and child restraints properly. If a child in a rear facing infant seat must be transported in front, the passenger air bag must be turned OFF. This is because the back of the infant seat is too close to the inflating air bag and the risk of a fatal injury to the infant when the air bag inflates is substantial. The vast majority of drivers and passengers are much safer with an air bag than without.
Seating and Safety Restraints 3. Medical condition. A passenger has a medical condition which, according to his or her physician: • causes the passenger air bag to pose a special risk for the passenger; and • makes the potential harm from the passenger air bag in a crash greater than the potential harm from turning OFF the air bag and allowing the passenger, even if belted, to hit the dashboard or windshield in a crash.
Seating and Safety Restraints 3. Medical condition: A passenger has a medical condition that, according to his or her physician: • poses a special risk for the passenger if the air bag deploys; and • makes the potential harm from the passenger air bag deployment greater than the potential harm from turning OFF the air bag and experiencing a crash without the protection offered by the air bag. This vehicle has special energy management safety belts for the driver and/or right front passenger.
Seating and Safety Restraints When possible, always place children under age 12 in the rear seat of your vehicle. Accident statistics suggest that children are safer when properly restrained in the rear seating positions than in the front seating positions. Do not install a child seat in a center facing jump seat. Children and safety belts If the child is the proper size, restrain the child in a safety seat.
Seating and Safety Restraints When children should use booster seats Children need to use booster seats from the time they outgrow the toddler seat until they are big enough for the vehicle seat and lap/shoulder belt to fit properly. Generally this is when they weigh about 80 lbs (about 8 to 12 years old).
Seating and Safety Restraints • Those with a high back. If, with a backless booster seat, you cannot find a seating position that adequately supports your child’s head, a high back booster seat would be a better choice. Both can be used in any vehicle in a seating position equipped with lap/shoulder belts if your child is over 40 lbs. The shoulder belt should cross the chest, resting snugly on the center of the shoulder.
Seating and Safety Restraints SAFETY SEATS FOR CHILDREN Child and infant or child safety seats Use a safety seat that is recommended for the size and weight of the child. Carefully follow all of the manufacturer’s instructions with the safety seat you put in your vehicle. If you do not install and use the safety seat properly, the child may be injured in a sudden stop or collision.
Seating and Safety Restraints Ford recommends the use of a child safety seat having a top tether strap. Install the child safety seat in a seating position which is capable of providing a tether anchorage. For more information on top tether straps, refer to Attaching child safety seats with tether straps in this chapter. Carefully follow all of the manufacturer’s instructions included with the safety seat you put in your vehicle.
Seating and Safety Restraints 2. Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together. 3. While holding the shoulder and lap belt portions together, route the tongue through the child seat according to the child seat manufacturer’s instructions. Be sure the belt webbing is not twisted. 4. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) for that seating position until you hear and feel the latch engage.
Seating and Safety Restraints 5. To put the retractor in the automatic locking mode, grasp the shoulder portion of the belt and pull downward until all of the belt is extracted and a click is heard. 6. Allow the belt to retract. The belt will click as it retracts to indicate it is in the automatic locking mode. 7. Pull the lap belt portion across the child seat toward the buckle and pull up on the shoulder belt while pushing down with knee on the child seat. 8.
Seating and Safety Restraints Attaching child safety seats with tether straps Most new forward-facing child safety seats include a tether strap which goes over the back of the seat and hooks to an anchoring point. Tether straps are available as an accessory for many older safety seats. Contact the manufacturer of your child seat for information about ordering a tether strap. The tether anchors in your vehicle are located on the back of the front seat cushion.
Seating and Safety Restraints 1. Position the child safety seat on the front seat cushion. 2. Route the child safety seat tether strap over the back of the seat. 3. Locate the correct anchor for the selected seating position. The tether anchor is located on the rear lower portion of the passenger seat.
Seating and Safety Restraints 4. Clip the tether strap to the anchor.
Seating and Safety Restraints Center seating location When installing a child safety seat in the front center position, route the tether strap over the center arm rest and clip it to the center anchor.
Seating and Safety Restraints Center seating location 60/40 vinyl seats When installing a child safety seat in the center position on a 60/40 vinyl seat, route the tether strap through the guiding sleeve and clip it to the center anchor. If the tether strap is clipped incorrectly, the child safety seat may not be retained properly in the event of a collision. 5.
Seating and Safety Restraints This type of child seat eliminates the need to use seat belts to attach the child seat. For forward-facing child seats, the tether strap must also be attached to the proper tether anchor. See Attaching safety seats with tether straps in this chapter. Your vehicle may be equipped with LATCH anchors for child seat installation at the seating positions with tan or gray locator buttons. • Bucket seats • 60/40 seats Never attach two LATCH child safety seats to the same anchor.
Seating and Safety Restraints The lower anchors for child seat installation are located at the rear section of the front passenger seat between the cushion and seat back. The LATCH anchors are below the gray or tan locator buttons on the seat back. Two plastic LATCH guides may be obtained at no charge from any Ford dealer (part number 1W4Z-54613F16–AA). They snap onto the latch lower anchor in the vehicle to help attach a child seat with rigid latch attachments.
Driving STARTING Positions of the ignition 1. ACCESSORY, allows the electrical accessories such as the radio to 4 operate while the engine is not 3 running. 5 2. LOCK, locks the steering wheel, automatic transmission gearshift 2 lever and allows key removal. 3. OFF, shuts off the engine and all 1 accessories without locking the steering wheel. This position also allows the automatic transmission shift lever to be moved from the P (Park) position without the brake pedal being depressed.
Driving Do not park, idle, or drive your vehicle in dry grass or other dry ground cover. The emission system heats up the engine compartment and exhaust system, which can start a fire. Do not start your vehicle in a closed garage or in other enclosed areas. Exhaust fumes can be toxic. Always open the garage door before you start the engine. See Guarding against exhaust fumes in this chapter for more instructions.
Driving If starting a vehicle with a manual transmission: • Make sure the parking brake is set. • Push the clutch pedal to the floor. 3. Turn the key to 4 (ON) without turning the key to 5 (START). 4 3 5 2 1 Make sure the corresponding lights illuminate or illuminate briefly. If a light fails to illuminate, have the vehicle serviced. • If the driver’s safety belt is fastened, the light may not illuminate.
Driving Starting the engine Note: Whenever you start your vehicle, release the key as soon as the engine starts. Excessive cranking could damage the starter. 1. Turn the key to 5 (START) without pressing the accelerator 4 pedal and release as soon as the 3 engine starts. The key will return to 5 4 (ON). 2. If the temperature is above –12° 2 C (10° F) and the engine does not start within five seconds on the first try, turn the key to OFF, wait 10 1 seconds and try again.
Driving Guarding against exhaust fumes Although odorless and colorless, carbon monoxide is present in exhaust fumes. Take precautions to avoid its dangerous effects. If you ever smell exhaust fumes of any kind inside your vehicle, have your dealer inspect and fix your vehicle immediately. Do not drive if you smell exhaust fumes. These fumes are harmful and could kill you. Have the exhaust and body ventilation systems checked whenever: • the vehicle is raised for service.
Driving road dust, salt or mud. If a “metal-to-metal,” “continuous grinding” or “continuous squeal” sound is present while braking, the brake linings may be worn-out and should be inspected by a qualified service technician. If you are driving down a long or steep hill, shift to a lower gear. Do not apply your brakes continuously, as they may overheat and become less effective. Anti-lock brake system (ABS) This vehicle is equipped with an anti-lock braking system (ABS).
Driving ABS warning lamp ABS The ABS warning lamp in the instrument cluster momentarily illuminates when the ignition is turned to the ON position. If the light does not illuminate momentarily at start up, remains on or continues to flash, the ABS needs to be serviced. With the ABS light on, the anti-lock brake system is disabled and normal ! braking is still effective unless the BRAKE brake warning light also remains illuminated with parking brake released.
Driving Pull the release lever to release the brake. Driving with the parking brake on will cause the brakes to wear out quickly and reduce fuel economy. BRAKE RELEASE STEERING Your vehicle is equipped with power steering. Power steering uses energy from the engine to decrease the driver’s effort in steering the vehicle. To prevent damage to the power steering pump: • Never hold the steering wheel to the extreme right or the extreme left for more than a few seconds when the engine is running.
Driving To reduce the risk of injury, never run the engine with one wheel off the ground, such as when changing a tire. PREPARING TO DRIVE YOUR VEHICLE Utility vehicles have a significantly higher rollover rate than other types of vehicles. In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt. Your vehicle has special design and equipment features to make it capable of performing in a wide variety of circumstances.
Driving If you cannot move the gearshift lever out of P (Park) with ignition in the ON position and the brake pedal depressed: 1. Apply the parking brake, turn ignition key to LOCK, then remove the key. 2. Insert the key and turn it to OFF. Apply the brake pedal and shift to N (Neutral). In the ignition OFF position, the automatic transmission shift lever can be moved from the P (Park) position without the brake pedal depressed. To avoid unwanted vehicle movement, always set the parking brake. 3.
Driving durability, and provide consistent shift feel over the life of the vehicle. It is normal for a new transmission to shift firmly. This operation is considered normal and will not affect function or durability of the transmission. Once the vehicle is at operating temperature it may take several shifts at the same operating condition for the transmission to properly adapt. Over time the adaptive learning process will fully update transmission operation.
Driving N (Neutral) With the gearshift lever in N (Neutral), the vehicle can be started and is free to roll. Hold the brake pedal down while in this position. (Overdrive) The normal driving position for the best fuel economy. Transmission operates in gears one through five. (Overdrive) can be deactivated by pressing the transmission control switch on the end of the gearshift lever. The transmission control indicator light (TCIL) will illuminate on the instrument cluster.
Driving 2 (Second) Use 2 (Second) to start-up on slippery roads or to provide additional engine braking on downgrades. 1 (First) Use 1 (First) to provide maximum engine braking on steep downgrades. Upshifts can be made by shifting to 2 (Second) or to (Overdrive). Selecting 1 (Low) at higher speeds causes the transmission to shift to a lower gear and will shift to 1 (First) after the vehicle decelerates to the proper vehicle speed.
Driving • Do not drive with your foot resting on the clutch pedal. Do not use the clutch to hold your vehicle at a standstill while waiting on a hill. These actions may reduce clutch life. PARKING 1. Apply the brake and shift into N (Neutral). 2. Engage the parking brake. 3. Shift into 1 (First). 4. Turn the ignition to Off. Do not park your vehicle in Neutral, it may move unexpectedly and injure someone. Use 1 (First) gear and set the parking brake fully.
Driving RECOMMENDED SHIFT SPEEDS Upshifts when accelerating (for best fuel economy) Transfer case position (if equipped) Shift from: 4H 4L 1-2 14 km/h (10 mph) 5 km/h (4 mph) 2-3 32 km/h (22 mph) 11 km/h (9 mph) 3 -4 50 km/h (33 mph) 19 km/h (13 mph) 4 - 5 (Overdrive) 71 km/h (41 mph) 27 km/h (17 mph) Upshifts when cruising (recommended for best fuel economy) Transfer case position (if equipped) Shift from: 4H 4L 1 -2 16 km/h (10 mph) 6 km/h (4 mph) 2-3 26 km/h (19 mph) 10 km/h (8 mph) 3-4 43 km/h (28 mph)
Driving FOUR-WHEEL DRIVE (4WD) OPERATION (IF EQUIPPED) For important information regarding safe operation of this type of vehicle, see Preparing to drive your vehicle in this chapter. When four–wheel drive (4WD) is engaged, power is supplied to all four wheels through a transfer case. 4WD can be selected when additional driving power is desired. If equipped with the Electronic Shift 4WD System, and 4WD Low is selected while the vehicle is moving, the 4WD system will not engage.
Driving Shifting from 2H (2WD high) to 4H (4WD high) Move the transfer case lever to 4H 2H (4WD High) at a stop or any forward speed up to 88 km/h 4H (55 mph). N • At temperatures below 0°C (32°F), shifts from 2H (2WD 4L High) to 4H (4WD High) should not be performed above 72 km/h (45 mph). Do not shift into 4H (4WD High) with the rear wheels slipping. Shifting from 4H (4WD high) to 2H (2WD high) Move the transfer case lever to 2H (2WD High) at a stop or any forward speed up to 88 km/h (55 mph).
Driving 3. Depress the clutch. 4. Move the transfer case shift lever through N (Neutral) directly to 4H (4WD High) or 2H (2WD high) and hold the shift lever in position until the transfer case has fully engaged (up to 15 seconds). 5. If the transfer case does not engage, repeat steps 1 through 4. 2H 4H N 4L Using the N (Neutral) position The transfer case neutral position overrides the transmission and puts the vehicle in neutral regardless of transmission gearshift lever position.
Driving Shifting from 2WD (2WD high) to 4X4 HIGH (4WD high) Move the 4WD control to the 4X4 HIGH position. 4X4 4X4 HIGH LOW 2WD Do not shift into 4X4 HIGH with the rear wheels slipping. Shifting from 4X4 HIGH (4WD high) to 2WD (2WD high) Move the 4WD control to 2WD 4X4 position at any forward speed. 4X4 HIGH LOW 2WD • You do not need to operate the vehicle in R (Reverse) to disengage your front hubs. Shifting from 2WD (2WD high) to 4X4 LOW (4WD low) 1. Bring the vehicle to a stop. 2. Depress the brake. 3.
Driving Shifting from 4X4 LOW (4WD low) to 2WD (2WD high) 1. Bring the vehicle to a stop. 2. Depress the brake. 3. Place the gearshift in N (Neutral) (automatic transmission) or depress the clutch (manual transmission). 4. Move the 4WD control to the 2WD position. 4X4 2WD HIGH 4X4 LOW Shifting between 4X4 HIGH (4WD high) and 4X4 LOW (4WD low) 1. Bring the vehicle to a stop. 2. Depress the brake. 3. Place the gearshift in N (Neutral) (automatic transmission) or depress the clutch (manual transmission). 4.
Driving The differences that make your vehicle so versatile also make it handle differently than an ordinary passenger car. Maintain steering wheel control at all times, especially in rough terrain. Since sudden changes in terrain can result in abrupt steering wheel motion, make sure you grip the steering wheel from the outside. Do not grip the spokes. Drive cautiously to avoid vehicle damage from concealed objects such as rocks and stumps.
Driving Vehicles with a higher center of gravity such as utility and four-wheel drive vehicles handle differently than vehicles with a lower center of gravity. Utility and four-wheel drive vehicles are not designed for cornering at speeds as high as passenger cars any more than low-slung sports cars are designed to perform satisfactorily under off-road conditions. Avoid sharp turns, excessive speed and abrupt maneuvers in these vehicles.
Driving called for. Avoid abrupt steering, acceleration or braking which could result in an increased risk of loss of vehicle control, vehicle rollover and/or personal injury. Use all available road surface to return the vehicle to a safe direction of travel. • In the event of an emergency stop, avoid skidding the tires and do not attempt any sharp steering wheel movements.
Driving Power is supplied to all four wheels through a transfer case. On 4WD vehicles, the transfer case allows you to select 4WD when necessary. Information on transfer case operation and shifting procedures can be found in the Driving chapter. Information on transfer case maintenance can be found in the Maintenance and specifications chapter. You should become thoroughly familiar with this information before you operate your vehicle.
Driving Once through water, always try the brakes. Wet brakes do not stop the vehicle as effectively as dry brakes. Drying can be improved by moving your vehicle slowly while applying light pressure on the brake pedal. Be cautious of sudden changes in vehicle speed or direction when you are driving in mud. Even 4WD vehicles can lose traction in slick mud. As when you are driving over sand, apply the accelerator slowly and avoid spinning your wheels.
Driving When climbing a steep slope or hill, start in a lower gear rather than downshifting to a lower gear from a higher gear once the ascent has started. This reduces strain on the engine and the possibility of stalling. If you do stall out, do not try to turn around because you might roll over. It is better to back down to a safe location. Apply just enough power to the wheels to climb the hill. Too much power will cause the tires to slip, spin or lose traction, resulting in loss of vehicle control.
Driving Avoid sudden braking as well. Although a 4WD vehicle may accelerate better than a two-wheel drive vehicle in snow and ice, it won’t stop any faster, because as in other vehicles, braking occurs at all four wheels. Do not become overconfident as to road conditions. Make sure you allow sufficient distance between you and other vehicles for stopping. Drive slower than usual and consider using one of the lower gears. In emergency stopping situations, avoid locking of the wheels.
Driving Tires can be damaged during off-road use. For your safety, tires that are damaged should not be used for highway driving because they are more likely to blow out or fail. You should carefully observe the recommended tire inflation pressure found on the safety compliance certification label attached to the left front door lock facing or door latch post pillar. Failure to follow tire pressure recommendations can adversely affect the way your vehicle handles.
Driving Failure to maintain your vehicle properly may void the warranty, increase your repair cost, reduce vehicle performance and operational capabilities and adversely affect driver and passenger safety. Frequent inspection of vehicle chassis components is recommended if the vehicle is subjected to heavy off-road usage. DRIVING THROUGH WATER Do not drive quickly through standing water, especially if the depth is unknown.
Driving • GCW (Gross Combined Weight): The combined weight of the towing vehicle (including occupants and cargo) and the loaded trailer. • GCWR (Gross Combined Weight Rating): Maximum permissible combined weight of towing vehicle (including occupants and cargo) and the loaded trailer • Maximum Trailer Weight Rating: Maximum weight of a trailer the vehicle is permitted to tow.
Driving Exceeding any vehicle weight rating limitation could result in serious damage to the vehicle loss of vehicle control, vehicle rollover, and/or personal injury. Special loading instructions for owners of pickup trucks and utility-type vehicles For important information regarding safe operation of this type of vehicle, see the Preparing to drive your vehicle section in this chapter. Loaded vehicles, with a higher center of gravity, may handle differently than unloaded vehicles.
Driving Engine 2.3L 4x2 w/manual transmission Maximum Maximum GCWR - kg trailer (lbs.) weight - kg (lbs.) Regular Cab w/6’ box All 2177 (4800) 753 (1660) Rear axle ratio Maximum frontal area of trailer m2 (ft2) 3.0L (non-torsion bar suspension) 3.0L (torsion bar suspension) 4.0L (non-torsion bar suspension) 4.0L (torsion bar suspension) All 2722 (6000) 1207 (2660) Equal to frontal area of vehicle 4.64 (50) All 2722 (6000) 1152 (2540) 4.64 (50) All 3175 (7000) 1624 (3580) 4.
Driving Engine 2.3L 4x2 w/manual transmission Maximum Maximum GCWR - kg trailer (lbs.) weight - kg (lbs.) SuperCab All 2177 (4800) 671 (1480) Rear axle ratio Maximum frontal area of trailer m2 (ft2) Equal to frontal area of vehicle 4.64 (50) 3.0L All 2722 (6000) 1125 (2480) (non-torsion bar suspension) 3.0L All 2722 (6000) 1052 (2320) 4.64 (50) (torsion bar suspension) 4.0L All 3175 (7000) 1542 (3400) 4.64 (50) (non-torsion bar suspension) 4.0L All 3175 (7000) 1479 (3260) 4.
Driving Engine 3.0L 4.0L 3.0L 4.0L 4x4 w/manual transmission Rear Maximum Maximum axle GCWR - kg trailer ratio (lbs.) weight - kg (lbs) Regular Cab w/6’ box All 2722 (6000) 1180 (2380) All 3175 (7000) 1506 (3320) Regular Cab w/7’ box All 2722 (6000) 1061 (2340) All 3175 (7000) 1479 (3260) SuperCab All 2722 (6000) 1007 (2220) All 3175 (7000) 1424 (3140) All 3175 (7000) 1234 (2720) Maximum frontal area of trailer m2 (ft2) 4.64 (50) 4.64 (50) 4.64 (50) 4.64 (50) 3.0L 4.64 (50) 4.0L 4.64 (50) 4.0L (FX4 4.
Driving Engine 2.3L 3.0L (non-torsion bar suspension 3.0L (torsion bar suspension) 4.0L (non-torsion bar suspension) 4.0L (torsion bar suspension) 4x2 w/automatic transmission Rear Maximum Maximum axle GCWR - kg trailer ratio (lbs.) weight - kg (lbs.) Regular Cab w/6’ box All 2495 (5500) 1025 (2260) Maximum frontal area of trailer m2 (ft2) All 3402 (7500) 1869 (4120) Equal to frontal area of vehicle 4.64 (50) All 3402 (7500) 1814 (4000) 4.64 (50) All 4309 (9500) 2740 (6040) 4.
Driving Engine 4x2 w/automatic transmission Rear Maximum Maximum axle GCWR - kg trailer ratio (lbs.) weight - kg (lbs.) All 3402 (7500) 1715 (3780) Maximum frontal area of trailer m2 (ft2) 4.64 (50) 3.0L (torsion bar suspension) 4.0L All 4309 (9500) 2667 (5880) 4.64 (50) (non-torsion bar suspension) 4.0L All 4309 (9500) 2595 (5720) 4.64 (50) (torsion bar suspension) For high altitude operation, reduce GCW by 2% per 300 meters (1000 ft.) elevation.
Driving Engine 3.0L 4.0L 3.0L 4.0L 4x4 w/automatic transmission Rear Maximum Maximum axle GCWR - kg trailer ratio (lbs.) weight - kg (lbs.) Regular Cab w/6’ box All 3402 (7500) 1751 (3860) All 4309 (9500) 2622 (5780) Regular Cab w/7’ box All 3402 (7500) 1724 (3800) All 4309 (9500) 2595 (5720) SuperCab All 3402 (7500) 1669 (3680) All 4309 (9500) 2540 (5600) All 4309 (9500) 2350 (5180) Maximum frontal area of trailer m2 (ft2) 4.64 (50) 4.64 (50) 4.64 (50) 4.64 (50) 3.0L 4.64 (50) 4.0L 4.64 (50) 4.
Driving Preparing to tow Use the proper equipment for towing a trailer and make sure it is properly attached to your vehicle. See your dealer or a reliable trailer dealer if you require assistance. Hitches For towing trailers up to 907 kg (2,000 lb), use a weight carrying hitch and ball which uniformly distributes the trailer tongue loads through the underbody structure. Use a frame-mounted weight distributing hitch for trailers over 907 kg (2,000 lb).
Driving Trailer lamps Trailer lamps are required on most towed vehicles. Make sure your trailer lamps conform to local and Federal regulations. See your dealer or trailer rental agency for proper instructions and equipment for hooking up trailer lamps. Using a step bumper The optional step bumper is equipped with an integral hitch and requires only a ball with a 19 mm (3/4 inch) shank diameter. The bumper has a 907 kg (2,000 lb.) trailer weight and 91 kg (200 lb.) tongue weight capability.
Driving Refer to the following chart for information regarding the factory-equipped trailer tow connector: Trailer tow connector Color Function 1. Dark Green Trailer right-hand turn signal 2. Yellow Trailer left-hand turn signal 3. Tan/White Tail lamp 4. White Ground Comment Circuit activated when brake pedal is depressed or when ignition is on and right-hand turn signal is applied. Circuit activated when brake pedal is depressed or when ignition is on and left-hand turn signal is applied.
Driving • Allow more distance for stopping with a trailer attached. • The trailer tongue weight should be 10–15% of the loaded trailer weight. • After you have traveled 80 km (50 miles), thoroughly check your hitch, electrical connections and trailer wheel lug nuts. • To aid in engine/transmission cooling and A/C efficiency during hot weather while stopped in traffic, place the gearshift lever in P (Park) (automatic transmission) or N (Neutral) (manual transmissions).
Driving • • • • Turn the key in the ignition to the OFF/UNLOCKED position. The maximum recommended speed is 88 km/h (55 mph). The maximum recommended distance is unlimited. The vehicle must be towed in the forward position to ensure no damage is done to the internal transfer case components. In addition, it is recommended that you follow the instructions provided by the aftermarket manufacturer of the towing apparatus if one has been installed.
Driving • Do not exceed a distance of 80 km (50 miles). • Do not exceed 56 km/h (35 mph) vehicle speed. • The vehicle must be towed in the forward position to ensure no damage is done to the internal transfer case components. If a distance of 80 km (50 miles) or a speed of 56 km/h (35 mph) must be exceeded, you must disconnect the front (4x4 only) and rear driveshafts. Ford recommends the driveshafts be removed/installed only by a qualified technician.
Roadside Emergencies GETTING ROADSIDE ASSISTANCE To fully assist you should you have a vehicle concern, Ford Motor Company offers a complimentary roadside assistance program. This program is separate from the New Vehicle Limited Warranty. The service is available: • 24–hours, seven days a week • for the New Vehicle Limited Warranty period of three years or 60,000 km (36,000 miles), whichever occurs first on Ford and Mercury vehicles, and four years or 80,000 km (50,000 miles) on Lincoln vehicles.
Roadside Emergencies U.S. Ford or Mercury vehicle customers who require roadside assistance, call 1–800–241–3673; Lincoln vehicle customers call 1–800–521–4140. Canadian customers who require roadside assistance, call 1–800–665–2006. If you need to arrange roadside assistance for yourself, Ford Motor Company will reimburse a reasonable amount. To obtain reimbursement information, U.S. Ford or Mercury vehicles customers call 1-800-241-3673; Lincoln vehicle customers call 1–800–521–4140.
Roadside Emergencies FUEL PUMP SHUT-OFF SWITCH FUEL RESET The fuel pump shut-off switch is a device intended to stop the electric fuel pump when your vehicle has been involved in a substantial jolt. After a collision, if the engine cranks but does not start, the fuel pump shut-off switch may have been activated. The “Fuel Reset” indicator light will illuminate in the instrument cluster. The fuel pump shut-off switch is located in the passenger’s foot well, by the kick panel.
Roadside Emergencies FUSES AND RELAYS Fuses If electrical components in the vehicle are not working, a fuse may have blown. Blown fuses are identified by a broken wire within the fuse. Check the appropriate fuses before replacing any electrical components. 15 Note: Always replace a fuse with one that has the specified amperage rating. Using a fuse with a higher amperage rating can cause severe wire damage and could start a fire.
Roadside Emergencies Passenger compartment fuse panel The fuse panel is located on the left-hand side of the instrument panel facing the driver’s side door. Pull the panel cover outward to access the fuses. 28 24 20 16 12 8 4 To remove a fuse use the fuse puller tool provided.
Roadside Emergencies The fuses are coded as follows: Fuse/Relay Location 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 Fuse Amp Rating 5A 10A Passenger Compartment Fuse Panel Description Power mirror switch Daytime Running Lights (DRL), Back-up lamps, Transmission, Passenger air bag deactivation switch, Blower motor relay 7.5A Right stop/turn trailer tow connector — Not used 15A 4x4 control module 2A Brake pressure switch 7.5A Left stop/turn trailer tow connector — Not used 7.
Roadside Emergencies Fuse/Relay Location 19 Fuse Amp Rating 25A 20 21 22 23 24 7.5A 15A 20A — 7.5A 25 26 — 10A 27 28 29 30 31 32 33 — 7.
Roadside Emergencies Power distribution box The power distribution box is located in the engine compartment. The power distribution box contains high-current fuses that protect your vehicle’s main electrical systems from overloads. Always disconnect the battery before servicing high current fuses. To reduce risk of electrical shock, always replace the cover to the Power Distribution Box before reconnecting the battery or refilling fluid reservoirs.
Roadside Emergencies 2.
Roadside Emergencies Fuse/Relay Location 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Fuse Amp Rating — — 40A** 20A** — — — 10A* — 20A* 30A* 10A* — — 30A* — 15A* 20A* 32 33 34 35 36 37 38 39 40 41 42 43 — 15A* — — — — 10A* — — 20A* 10A* — Power Distribution Box Description Not used Not used Blower motor Auxiliary cooling fan Not used Not used Not used PCM memory Not used Fuel pump motor Headlamps A/C clutch solenoid Not used Not used ABS module Not used Trailer tow Foglamps, Daytime Running Lam
Roadside Emergencies Fuse/Relay Fuse Amp Location Rating 44 — 45A — 45B — 46A — 46B — 47 — 48 — 49 — 50 — 51 — 52 — 53 — 54 — 55 — 56A — 56B — * Mini Fuses ** Maxi Fuses 204 Power Distribution Box Description Not used Wiper HI/LO Wiper park/run Fuel pump Trailer tow Starter Auxiliary cooling fan Not used Not used Not used Not used PCM Diode PCM Blower A/C clutch solenoid Front washer pump
Roadside Emergencies 3.0L and 4.
Roadside Emergencies 206 Fuse/Relay Location 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Fuse Amp Rating — — 40A** — — — — 10A* — 20A* 30A* 10A* — — 30A* — 15A* 20A* 32 33 34 35 36 37 38 39 40 41 42 43 — 15A* — — — — 10A* — — 20A* 10A* — Power Distribution Box Description Not used Not used Blower motor Not used Not used Not used Not used PCM memory Not used Fuel pump motor Headlamps A/C clutch solenoid Not used Not used ABS Module Not used Trailer tow Foglamps, Daytime Running Lamps (DRL) No
Roadside Emergencies Fuse/Relay Fuse Amp Power Distribution Box Location Rating Description 44 — Not used 45A — Wiper HI/LO 45B — Wiper park/run 46A — Fuel pump 46B — Trailer tow 47A — A/C clutch solenoid 47B — Front washer pump 48A — Fog lamps 48B — Fog lamp relay 51 — Not used 52 — Not used 53 — PCM Diode 54 — PCM 55 — Blower 56 — Starter * Mini Fuses ** Maxi Fuses CHANGING THE TIRES If you get a flat tire while driving, do not apply the brake heavily. Instead, gradually decrease your speed.
Roadside Emergencies If you use the temporary spare tire continuously or do not follow these precautions, the tire could fail, causing you to lose control of the vehicle, possibly injuring yourself or others.
Roadside Emergencies Location of the spare tire and tools The spare tire and tools for your vehicle are stowed in the following locations: Tool Spare tire Jack, jack handle, wheel nut wrench Key, spare tire lock (if equipped) Location Under the vehicle, just forward of the rear bumper Regular Cab: behind seats and underneath the jack and tools cover SuperCab: stowed in the passenger side rear cab compartment or behind the jump seat in a separate tool bag Four-door models: stowed behind the front seats, be
Roadside Emergencies 2. If equipped, unlock and remove the spare tire carrier lock from the rear access hole located just above the rear bumper and below the tailgate. 3. Insert the straight end of the jack handle into the rear access hole located just above the rear bumper and below the tailgate. Forward motion will stop and resistance to turning will be felt when properly engaged. 4. Turn the handle counterclockwise until tire is lowered to the ground and the cable is slightly slack. 5.
Roadside Emergencies 5. If removed, install the spare tire carrier lock on the access hole above the bumper. Tire change procedure To prevent the vehicle from moving when you change a tire, be sure the parking brake is set, then block (in both directions) the wheel that is diagonally opposite (other side and end of the vehicle) to the tire being changed. If the vehicle slips off the jack, you or someone else could be seriously injured. 1.
Roadside Emergencies • Front • Rear To lessen the risk of personal injury, do not put any part of your body under the vehicle while changing a tire. Do not start the engine when your vehicle is on the jack. The jack is only meant for changing the tire. • Never use the differential as a jacking point. 7. Remove the wheel lug nuts with the lug wrench. 8. Replace the flat tire with the spare tire, making sure the valve stem is facing outward. Reinstall the lug nuts until the wheel is snug against the hub.
Roadside Emergencies 9. Lower the wheel by turning the jack handle counterclockwise. 10. Remove the jack and fully 1 tighten the lug nuts, in the order shown, to 135 Nm (100 lb-ft). Note that these tightening specifications 3 4 are for nut and bolt threads that are free of dirt and rust. Use only Ford recommended (1/2–20) replacement fasteners. 5 2 11. Stow the flat tire. Refer to Stowing the spare tire. 12. Stow the jack and lug wrench. Make sure the jack is fastened so it does not rattle when you drive.
Roadside Emergencies 4. Check all battery terminals and remove any excessive corrosion before you attach the battery cables. Ensure that vent caps are tight and level. 5. Turn the heater fan on in both vehicles to protect any electrical surges. Turn all other accessories off. Connecting the jumper cables + + – – 1. Connect the positive (+) booster cable to the positive (+) terminal of the discharged battery.
Roadside Emergencies + + – – 3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery. + + – – 4. Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle’s engine, away from the battery and the carburetor/fuel injection system. Do not use fuel lines, engine rocker covers or the intake manifold as grounding points. Do not connect the end of the second cable to the negative (-) terminal of the battery to be jumped.
Roadside Emergencies Jump starting 1. Start the engine of the booster vehicle and run the engine at moderately increased speed. 2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both engines for an additional three minutes before disconnecting the jumper cables. Removing the jumper cables + + – – Remove the jumper cables in the reverse order that they were connected. 1. Remove the jumper cable from the ground metal surface.
Roadside Emergencies + + – – 3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’s battery. + + – – 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’s battery. After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn its idle conditions.
Roadside Emergencies WRECKER TOWING If you need to have your vehicle towed, contact a professional towing service or, if you are a member, your roadside assistance center. It is recommended that your vehicle be towed with a wheel lift or flatbed equipment. Do not tow with a slingbelt. Ford Motor Company has not approved a slingbelt towing procedure. On 4x2 vehicles, it is acceptable to tow the vehicle with the front wheels on the ground and the rear wheels off the ground.
Customer Assistance GETTING THE SERVICES YOU NEED At home Ford Motor Company and Ford of Canada have authorized dealerships to service your vehicle. It is preferred that you return to the authorized dealer where your vehicle was purchased when warranty repairs are needed. However, you may also take your vehicle to another Ford Motor Company or Ford of Canada dealership authorized for warranty repairs.
Customer Assistance In Canada: Customer Relationship Centre Ford Motor Company of Canada, Limited P.O. Box 2000 Oakville, Ontario L6J 5E4 1-800-565-3673 (FORD) www.ford.ca If you own a Lincoln vehicle and are away from home when your vehicle needs service, or if you need more help than the dealership could provide, after following the steps described above, contact the Ford Customer Relationship Center to find an authorized dealership to help you.
Customer Assistance In some states (in the U.S.) you must directly notify Ford in writing before pursuing remedies under your state’s warranty laws. Ford is also allowed a final repair attempt in some states. In the United States, a warranty dispute must be submitted to the Dispute Settlement Board before taking action under the Magnuson-Moss Warranty Act, or to the extent allowed by state law, before pursuing replacement or repurchase remedies provided by certain state laws.
Customer Assistance THE DISPUTE SETTLEMENT BOARD (U.S. ONLY) The Dispute Settlement Board is: • an independent, third-party arbitration program for warranty disputes. • available free to owners and lessees of qualifying Ford Motor Company vehicles. The Dispute Settlement Board may not be available in all states.
Customer Assistance Board membership The Board consists of: • Three consumer representatives • A Ford or Lincoln Mercury dealership representative Consumer candidates for Board membership are recruited and trained by an independent consulting firm. The dealership Board member is chosen from Ford and Lincoln Mercury dealership management, recognized for their business leadership qualities.
Customer Assistance Oral presentations If you would like to make an oral presentation, indicate YES to question 6 on the application. While it is your right to make an oral presentation before the Board, this is not a requirement and the Board will decide the case whether or not an oral presentation is made. An oral presentation may be requested by the Board as well.
Customer Assistance UTILIZING THE MEDIATION/ARBITRATION PROGRAM (CANADA ONLY) In those cases where you continue to feel that the efforts by Ford and the dealer to resolve a factory-related vehicle service concern have been unsatisfactory, Ford of Canada participates in an impartial third party mediation/arbitration program administered by the Canadian Motor Vehicle Arbitration Plan (CAMVAP).
Customer Assistance If your vehicle must be serviced while you are traveling or living in Central or South America, the Caribbean, or the Middle East, contact the nearest Ford dealership. If the dealership cannot help you, write or call: FORD MOTOR COMPANY WORLDWIDE DIRECT MARKET OPERATIONS 1555 Fairlane Drive Fairlane Business Park #3 Allen Park, Michigan 48101 U.S.A. Telephone: (313) 594-4857 FAX: (313) 390-0804 If you are in another foreign country, contact the nearest Ford dealership.
Customer Assistance IN CALIFORNIA (U.S. ONLY) California Civil Code Section 1793.
Customer Assistance REPORTING SAFETY DEFECTS (U.S. ONLY) If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Ford Motor Company. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.
Cleaning WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutral Ph shampoo, such as Motorcraft Detail Wash (ZC-3–A), which is available from your dealer. • Never use strong household detergents or soap, such as dish washing or laundry liquid. These products can discolor and spot painted surfaces. • Never wash a vehicle that is “hot to the touch” or during exposure to strong, direct sunlight.
Cleaning PAINT CHIPS Your dealer has touch-up paint and sprays to match your vehicle’s color. Take your color code (printed on a sticker in the driver’s door jam) to your dealer to ensure you get the correct color. • Remove particles such as bird droppings, tree sap, insect deposits, tar spots, road salt and industrial fallout before repairing paint chips. • Always read the instructions before using the products.
Cleaning • 2.3L I4 engine • 3.
Cleaning • 4.0L SOHC V6 engine • Never wash or rinse the engine while it is running; water in the running engine may cause internal damage. PLASTIC (NON-PAINTED) EXTERIOR PARTS Use only approved products to clean plastic parts. These products are available from your dealer. • For routine cleaning, use Motorcraft Detail Wash (ZC-3–A). • If tar or grease spots are present, use Ford Extra Strength Tar and Road Oil Removal (B7A-19520–AA).
Cleaning INSTRUMENT PANEL AND CLUSTER LENS Clean the instrument panel with a damp cloth, then dry with a dry cloth. • Avoid cleaners or polish that increase the gloss of the upper portion of the instrument panel. The dull finish in this area helps protect the driver from undesirable windshield reflection. Do not use chemical solvents or strong detergents when cleaning the steering wheel or instrument panel to avoid contamination of the air bag system.
Cleaning LEATHER SEATS (IF EQUIPPED) Your leather seating surfaces have a clear, protective coating over the leather. • To clean, use a soft cloth with Motorcraft Deluxe Leather and Vinyl Cleaner (ZC-11–A). Dry the area with a soft cloth. • To help maintain its resiliency and color, use the Motorcraft Deluxe Leather Care Kit (ZC-11–D), available from your authorized dealer.
Cleaning Motorcraft Dash and Vinyl Cleaner (ZC-38–A) Motorcraft Car Care Kit (ZC-26) Ford Premium Car Wash Concentrate (F2SZ-19523–WC) Motorcraft Carlite Glass Cleaner (Canada only) (CXC-100) Motorcraft Spot and Stain Remover (ZC-14) Motorcraft Detail Wash (ZC-3–A) Motorcraft Tire Detailer (ZC-28) Motorcraft Triple Clean (ZC-13) Motorcraft Ultra-Clear Spray Glass Cleaner (not available in Canada) (ZC-23) Motorcraft Engine Shampoo and Degreaser (ZC-20) * May be sold with the Motorcraft name 235
Maintenance and Specifications SERVICE RECOMMENDATIONS To help you service your vehicle: • We highlight do-it-yourself items in the engine compartment for easy location. • We provide a scheduled maintenance guide which makes tracking routine service easy. If your vehicle requires professional service, your dealership can provide the necessary parts and service. Check your Warranty Guide/Owner Information Guide to find out which parts and services are covered.
Maintenance and Specifications • Manual transmission: 1. Set the parking brake. 2. Depress the clutch and place the gearshift in 1 (First). 3. Turn off the engine and remove the key. 4. Block the wheels to prevent the vehicle from moving unexpectedly. Working with the engine on • Automatic transmission: 1. Set the parking brake and ensure the gearshift is securely latched in P (Park). 2. Block the wheels to prevent the vehicle from moving unexpectedly.
Maintenance and Specifications IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 2.3L I4 engine 1. Windshield washer fluid reservoir 2. Engine coolant reservoir 3. Engine oil dipstick 4. Transmission fluid dipstick (automatic transmission) 5. Engine oil filler cap 6. Brake fluid reservoir 7. Power distribution box 8. Clutch fluid reservoir (manual transmission) 9. Battery 10. Power steering fluid reservoir 11.
Maintenance and Specifications 3.0L V6 engine 1. Engine coolant reservoir 2. Windshield washer fluid reservoir 3. Engine oil filler cap 4. Automatic transmission fluid dipstick (if equipped) 5. Engine oil dipstick 6. Brake fluid reservoir 7. Power distribution box 8. Clutch fluid reservoir (if equipped) 9. Battery 10. Power steering fluid reservoir 11.
Maintenance and Specifications 4.0L SOHC V6 engine 1. Windshield washer fluid reservoir 2. Automatic transmission fluid dipstick (if equipped) 3. Engine oil filler cap 4. Engine oil dipstick 5. Brake fluid reservoir 6. Power distribution box 7. Clutch fluid reservoir (if equipped) 8. Battery 9. Power steering fluid reservoir 10. Air filter assembly 11.
Maintenance and Specifications WINDSHIELD WASHER FLUID Check the washer fluid whenever you stop for fuel. The reservoir is symbol. highlighted with a UID SHER FL WA Add fluid to fill the reservoir if the level is low. In very cold weather, do not fill the reservoir completely. Only use a washer fluid that meets Ford specification ESR-M17P5–A. Refer to Lubricant specifications in this chapter.
Maintenance and Specifications 4. Open the hood. Protect yourself from engine heat. 5. Locate and carefully remove the engine oil level indicator (dipstick). • 2.
Maintenance and Specifications • 3.
Maintenance and Specifications • 4.0L SOHC V6 engine MIN MAX 6. Wipe the indicator clean. Insert the indicator fully, then remove it again. • If the oil level is between the MIN and MAX marks, the oil level is acceptable, DO NOT ADD OIL. • If the oil level is below the MIN mark, add enough oil to raise the level within the MIN-MAX range.
Maintenance and Specifications • 2.3L I4 engine • 3.
Maintenance and Specifications • 4.0L SOHC V6 engine • Oil levels above the MAX mark may cause engine damage. Some oil must be removed from the engine by a service technician. 7. Put the indicator back in and ensure it is fully seated. Adding engine oil 1. Check the engine oil. For instructions, refer to Checking the engine oil in this chapter. 2. If the engine oil level is not within the normal range, add only certified engine oil of the recommended viscosity.
Maintenance and Specifications Engine Oil Recommendations 2.3L & 3.0L Engines Look for this certification trademark. SAE 5W-20 engine oil is recommended. Change your engine oil and filter according to the appropriate schedule listed in the scheduled maintenance guide. Do not use supplemental engine oil additives, oil treatments or engine treatments. They are unnecessary and could, under certain conditions, lead to engine damage which is not covered by your warranty. 4.
Maintenance and Specifications Engine Oil Filter Recommendation Change your engine oil filter according to the appropriate schedule listed in the scheduled maintenance guide. Ford production and aftermarket (Motorcraft) oil filters are designed for added engine protection and long life. If a replacement oil filter is used that does not meet Ford Material and design specifications, start-up engine noises or knock may be experienced.
Maintenance and Specifications If you see any corrosion on the battery or terminals, remove the cables from the terminals and clean with a wire brush. You can neutralize the acid with a solution of baking soda and water. Batteries normally produce explosive gases which can cause personal injury. Therefore, do not allow flames, sparks or lighted substances to come near the battery. When working near the battery, always shield your face and protect your eyes. Always provide proper ventilation.
Maintenance and Specifications RN LE TU AD RE • The vehicle may need to be driven to relearn the idle and fuel trim strategy. • If you do not allow the engine to relearn its idle trim, the idle quality of your vehicle may be adversely affected until the idle trim is eventually relearned. When the battery is disconnected or a new battery installed, the transmission must relearn its adaptive strategy. As a result of this, the transmission may shift firmly.
Maintenance and Specifications Your vehicle was factory-filled with a 50/50 engine coolant and water concentration. If the concentration of coolant falls below 40% or above 60%, the engine parts could become damaged or not work properly. A 50–50 mixture of coolant and water provides the following: • Freeze protection down to -36° C (-34° F). • • • • Boiling protection up to 129° C (265° F). Protection against rust and other forms of corrosion. Enables calibrated gauges to work properly. 2.3L engines • 3.
Maintenance and Specifications • Refer to the Scheduled Maintenance Guide for service interval schedules. • Be sure to read and understand Precautions when servicing your vehicle in this chapter. If the engine coolant has not been checked at the recommended interval, the engine coolant reservoir may become low or empty. If the reservoir is low or empty, add engine coolant to the reservoir. Refer to Adding engine coolant in this chapter.
Maintenance and Specifications • Do not add/mix an orange-colored, extended life coolant such as Motorcraft Speciality Orange Engine Coolant, VC-2 (US) or CXC-209 (Canada), meeting Ford specification WSS-M97B44–D with the factory-filled coolant. Mixing Motorcraft Speciality Orange Engine Coolant or any orange-colored extended life product with your factory filled coolant can result in degraded corrosion protection.
Maintenance and Specifications 5. Fill the coolant reservoir slowly with the proper coolant mixture (see above), to within the “cold fill range” or the “cold full” level on the reservoir. If you removed the radiator cap in an overflow system, fill the radiator until the coolant is visible and radiator is almost full. 6. Replace the cap. Turn until tightly installed. (Cap must be tightly installed to prevent coolant loss.
Maintenance and Specifications Severe climates If you drive in extremely cold climates (less than –36° C [–34° F]): • It may be necessary to increase the coolant concentration above 50%. • NEVER increase the coolant concentration above 60%. • Increased engine coolant concentrations above 60% will decrease the overheat protection characteristics of the engine coolant and may cause engine damage.
Maintenance and Specifications The fuel system may be under pressure. If the fuel filler cap is venting vapor or if you hear a hissing sound, wait until it stops before completely removing the fuel filler cap. Otherwise, fuel may spray out and injure you or others. If you do not use the proper fuel filler cap, excessive pressure or vacuum in the fuel tank may damage the fuel system or cause the fuel cap to disengage in a collision, which may result in possible personal injury.
Maintenance and Specifications clothing and wash skin thoroughly with soap and water. Repeated or prolonged skin contact with fuel liquid or vapor causes skin irritation. • Be particularly careful if you are taking “Antabuse” or other forms of disulfiram for the treatment of alcoholism. Breathing gasoline and/or ethanol vapors, or skin contact could cause an adverse reaction. In sensitive individuals, serious personal injury or sickness may result.
Maintenance and Specifications When refueling always shut the engine off and never allow sparks or open flames near the filler neck. Never smoke while refueling. Fuel vapor is extremely hazardous under certain conditions. Care should be taken to avoid inhaling excess fumes. The flow of fuel through a fuel pump nozzle can produce static electricity, which can cause a fire if fuel is pumped into an ungrounded fuel container.
Maintenance and Specifications If you must replace the fuel filler cap, replace it with a fuel filler cap that is designed for your vehicle. The customer warranty may be void for any damage to the fuel tank or fuel system if the correct genuine Ford or Motorcraft fuel filler cap is not used. The fuel system may be under pressure. If the fuel filler cap is venting vapor or if you hear a hissing sound, wait until it stops before completely removing the fuel filler cap.
Maintenance and Specifications FFV engine (if equipped) Your vehicle is designed to use (E85) Fuel Ethanol, “Regular” unleaded gasoline or any percentage of the two fuels combined. U.S. government regulations require fuel ethanol dispensing pumps to have a small, square, orange and black label with the common abbreviation or the appropriate percentage for that region. Use of other fuels such as Fuel Methanol may cause powertrain damage, a loss of vehicle performance, and your warranty may be invalidated.
Maintenance and Specifications FFV engine (if equipped) Your FFV will operate well on ordinary “Regular” unleaded gasoline, but only the highest quality fuel ethanol will provide the same level of protection and performance. To identify if your vehicle is an FFV, check your VIN or the label on the inside of your fuel filler door. When checking the VIN, look for the engine type identifier (8th character). If your vehicle is an FFV, then the character will be labeled as a “K.
Maintenance and Specifications ESSENTIALS OF GOOD FUEL ECONOMY Measuring techniques Your best source of information about actual fuel economy is you, the driver. You must gather information as accurately and consistently as possible. Fuel expense, frequency of fill-ups or fuel gauge readings are NOT accurate as a measure of fuel economy. We do not recommend taking fuel economy measurements during the first 1,600 km (1,000 miles) of driving (engine break-in period).
Maintenance and Specifications Calculating fuel economy 1. Fill the fuel tank completely and record the initial odometer reading (in kilometers or miles). 2. Each time you fill the tank, record the amount of fuel added (in liters or gallons). 3. After at least three to five tank fill-ups, fill the fuel tank and record the current odometer reading. 4. Subtract your initial odometer reading from the current odometer reading. 5.
Maintenance and Specifications • You may want to turn off the speed control in hilly terrain if unnecessary shifting between third and fourth gear occurs. Unnecessary shifting of this type could result in reduced fuel economy. • Warming up a vehicle on cold mornings is not required and may reduce fuel economy. • Resting your foot on the brake pedal while driving may reduce fuel economy. • Combine errands and minimize stop-and-go driving.
Maintenance and Specifications EPA window sticker Every new vehicle should have the EPA window sticker. Contact your dealer if the window sticker is not supplied with your vehicle. The EPA window sticker should be your guide for the fuel economy comparisons with other vehicles. It is important to note the box in the lower left corner of the window sticker. These numbers represent the Range of L/100 km (MPG) expected on the vehicle under optimum conditions.
Maintenance and Specifications Exhaust leaks may result in entry of harmful and potentially lethal fumes into the passenger compartment. Do not make any unauthorized changes to your vehicle or engine. By law, vehicle owners and anyone who manufactures, repairs, services, sells, leases, trades vehicles, or supervises a fleet of vehicles are not permitted to intentionally remove an emission control device or prevent it from working.
Maintenance and Specifications CHECKING AND ADDING POWER STEERING FLUID Check the power steering fluid. Refer to the scheduled maintenance guide for the service interval schedules. If adding fluid is necessary, use only MERCON威 ATF. 1. Start the engine and let it run until it reaches normal operating temperature (the engine coolant temperature gauge indicator will be near the center of the normal area between H and C). 2. While the engine idles, turn the steering wheel left and right several times. 3.
Maintenance and Specifications BRAKE FLUID Checking and adding brake fluid Brake fluid should be checked and refilled as needed. Refer to the scheduled maintenance guide for the service interval schedules. 1. Clean the reservoir cap before removal to prevent dirt or water from entering the reservoir. 2. Visually inspect the fluid level. 3. If necessary, add brake fluid from a clean un-opened container until MAX the level reaches MAX. Do not fill above this line. 4.
Maintenance and Specifications CLUTCH FLUID (IF EQUIPPED) Check the fluid level. Refer to the scheduled maintenance guide for the service interval schedules. During normal operation, the fluid level in the clutch reservoir should remain constant. If the fluid level drops, refill the fluid level to the step in the reservoir. Use only a DOT 3 brake fluid designed to meet Ford specification ESA-M6C25–A. Refer to Lubricant Specifications in this chapter. Brake fluid is toxic.
Maintenance and Specifications temperature (approximately 30 km [20 miles]). If your vehicle has been operated for an extended period at high speeds, in city traffic during hot weather or pulling a trailer, the vehicle should be turned off for about 30 minutes to allow fluid to cool before checking. 1. Drive the vehicle 30 km (20 miles) or until it reaches normal operating temperature. 2. Park the vehicle on a level surface and engage the parking brake. 3.
Maintenance and Specifications The transmission fluid should be in this range if at ambient temperature (10°C-35°C [50°F-95°F]). High fluid level Fluid levels above the safe range may result in transmission failure. An overfill condition of transmission fluid may cause shift and/or engagement concerns and/or possible damage. High fluid levels can be caused by an overheating condition. Adjusting automatic transmission fluid levels Before adding any fluid, make sure the correct type is used.
Maintenance and Specifications Checking and adding manual transmission fluid (if equipped) 1. Clean the filler plug. 2. Remove the filler plug and inspect the fluid level. 3. Fluid level should be at the bottom of the opening. 4. Add enough fluid through the filler opening so that the fluid level is at the bottom of the opening. 5. Install and tighten the fill plug securely. Use only fluid that meets Ford specifications. Refer to Lubricant Specifications in this chapter.
Maintenance and Specifications Checking and adding transfer case fluid (if equipped) 1. Clean the filler plug. 2. Remove the filler plug and inspect the fluid level. 3. Add only enough fluid through the filler opening so that the fluid level is at the bottom of the opening. Use only fluid that meets Ford specifications. Refer to Lubricant Specifications in this chapter. DRIVELINE UNIVERSAL JOINT AND SLIP YOKE Your vehicle may be equipped with universal joints that require lubrication.
Maintenance and Specifications INFORMATION ABOUT UNIFORM TIRE QUALITY GRADING New vehicles are fitted with tires that have a rating on them called Tire Quality Grades. The Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width. For example: • Treadwear 200 Traction AA Temperature A These Tire Quality Grades are determined by standards that the United States Department of Transportation has set.
Maintenance and Specifications The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning or peak traction characteristics. Temperature A B C The temperature grades are A (the highest), B and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel.
Maintenance and Specifications Tire rotation Because your vehicle’s tires perform different jobs, they often wear differently. To make sure your tires wear evenly and last longer, rotate them as indicated in the scheduled maintenance guide. If you notice that the tires wear unevenly, have them checked. The following procedure applies to vehicles equipped with single rear wheels, if your vehicle is equipped with dual rear wheels it is recommended that only the front wheels be rotated (side to side).
Maintenance and Specifications Replacing the tires Replace the tires when the wear band is visible through the tire treads. Due to exposure to the elements and exhaust you should replace the spare tire when you replace the other tires. When replacing full size tires, never mix radial bias-belted, or bias-type tires. Use only the tire sizes that are listed on the Certification Label. Make sure that all tires are the same size, speed rating, and load-carrying capacity.
Maintenance and Specifications Snow tires must be the same size and grade as the tires you currently have on your vehicle. The tires on your vehicle have all weather treads to provide traction in rain and snow. However, in some climates, you may need to use snow tires and chains. If you need to use snow tires and chains, it is recommended that steel wheels are used of the same size and specifications as those originally installed.
Maintenance and Specifications Component Spark plugs* 2.3L I4engine AWSF32FEM** 3.0 L V6 engine AWSF32PP*** 3.0L V6 FFV engine 4.0L V6 engine AGSF-22PP*** AGSF-34FP * Refer to Vehicle Emissions Control Information (VECI) decal for spark plug gap information. ** Two spark plugs per cylinder required (eight total). *** If any spark plug needs to be removed for inspection, it must be re-installed in the same cylinder. Cylinders No.1, 2 and 3 have a “PG” suffix. Cylinders No.
Maintenance and Specifications Fluid Ford Part Name Motorcraft MERCON威 ATF Motorcraft MERCON威V ATF Transmission fluid 1 Engine coolant 280 4 Application Capacity 5-speed manual 2.65L (2.8 quarts) 9.4L (9.9 quarts) 4x2 vehicles with automatic and 2.3L I4 engine 4x2 vehicles with automatic and 3.0L or 4.0L engines 4x4 vehicles with automatic and 3.0L or 4.0L Motorcraft 2.3 L I4 engine Premium Engine with manual Coolant transmission (green-colored) 2.
Maintenance and Specifications Fluid Fuel tank Transfer case Fluid Front axle lubricant Ford Part Name N/A Application Capacity Regular cab (Short wheel base) Regular cab (Long wheel base) SuperCab 62.4L (16.5 gallons) 75.7L (20.0 gallons) 73.8L (19.5 gallons) 1.2L (1.25 quarts) 1.7L (3.6 pints) Motorcraft 4x4 Vehicles MERCON威 ATF Motorcraft SAE 4x4 Vehicles 80W-90 Premium Rear Axle Lubricant Motorcraft SAE All 2.4-2.5L Rear axle 80W-90 (5.0-5.
Maintenance and Specifications 4 Add the coolant type originally equipped in your vehicle. 5 Traction-Lok axles use 2.2–2.4L (4.75–5.0 pints) of rear axle lubricant. Add 118 ml (4 oz.) of Additive Friction Modifier XL–3 or equivalent meeting Ford specification EST-M2C118–A for complete refill of Traction-Lok axles. Service refill capacities are determined by filling the rear axle 6 mm to 14 mm (1/4 inch to 9/16 inch) below the bottom of the filler hole.
Maintenance and Specifications Item Engine oil Ford part name or equivalent 2.3L and 3.0L engines Motorcraft SAE 5W-20 Premium Synthetic Blend Motor Oil 4.
Maintenance and Specifications Item Ford part name or equivalent Motorcraft MERCON威 ATF Power steering fluid, transfer case fluid (4X4) and transmission fluid (manual) Motorcraft Automatic transmission MERCON威V (5R44E and ATF 2 5R55E) Motorcraft Premium Windshield Windshield washer fluid Washer Concentrate Ford part number Ford specification XT-2-QDX MERCON威 XT-5-QM MERCON威V ZC-32–A WSB-M8B16–A2 1 Add 118 ml (4 oz.
Maintenance and Specifications Engine Compression ratio 2.3L I4 engine 9.7:1 3.0L V6 engine 4.0L V6 engine 9.7:1 9.0:1 VEHICLE DIMENSIONS Vehicle dimensions (1) Overall length (2) Overall width (3) Overall height 4x2/4x4 (4) Wheelbase (5) Track Front (5) Track Rear Regular Cab Short Wheel Base (SWB) mm (in) 4 763 (187.5) Regular Cab Long Wheel Base (LWB) mm (in) 5 093 (200.5) 5 153 (202.9) 1 785 (70.3) 1 785 (70.3) 1 785 (70.3) 1 1 2 1 1 1 2 1 1 1 3 1 593.5 (62.7) / 655 (65.2) 831 (111.
Maintenance and Specifications 4 1 4 1 286
Maintenance and Specifications IDENTIFYING YOUR VEHICLE Certification label The National Highway Traffic Safety Administration Regulations require that a Certification label be affixed to a vehicle and prescribe where the Certification label may be located. The Certification label is located on the front door latch pillar on the driver’s side. Vehicle identification number (VIN) The vehicle identification number is attached to a metal tag and is located on the driver side instrument panel.
Accessories FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of genuine Ford accessories are available for your vehicle through your local authorized Ford, Lincoln Mercury or Ford of Canada dealer. These quality accessories have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and aerodynamic appearance of your vehicle.
Accessories Bed tent (Short bed, Styleside only) Cellular phone holder Compass mirror Compass mirror with outside temperature reading Daytime running lights First aid kit Fog lights Peace of mind kit Pickup box rails (tubular) Removable bike carrier (bed mount/hitch mount) Running boards/bars Speed control Trailer hitch (Class III) Trailer hitch bars and balls Trailer hitch wiring adaptor Trailgate table Protection and appearance equipment Air bag anti-theft locks Bed mats Bedliners Bull bars (chrome & blac
Accessories Side window air deflectors Skid plate (4x4 only) Spare tire lock Tailgate protector Tail lamp surrounds (chrome & black) Tonneau covers — soft (snap and snapless) Tonneau cover (hard 2 piece) Tonneau cover (color keyed-Leer supplier branded) Universal floor mats Wheels Wheel locks For maximum vehicle performance, keep the following information in mind when adding accessories or equipment to your vehicle: • When adding accessories, equipment, passengers and luggage to your vehicle, do not exceed
Index A ABS (see Brakes) .....................156 Air bag supplemental restraint system ................................127–128 and child safety seats ............129 description ..............................128 disposal ....................................132 driver air bag ..........................130 indicator light ...................12, 131 operation .................................130 passenger air bag ...................130 passenger deactivation switch ......................................
Index Changing a tire .........................207 Child safety restraints ..............137 child safety belts ....................137 Child safety seats ......................140 attaching with tether straps ..144 in front seat ............................141 in rear seat ..............................141 Cleaning your vehicle engine compartment ..............230 instrument panel ....................233 interior .....................................233 plastic parts ............................
Index lubrication specifications ..................282, 284 refill capacities ........................279 service points ..................238–240 starting after a collision .........196 Engine block heater .................154 Engine oil ..................................241 checking and adding ..............241 dipstick ....................................241 filter, specifications ........247, 278 recommendations ...................247 refill capacities ........................279 specifications ........
Index Headlamps ...................................80 aiming ........................................81 bulb specifications ....................83 daytime running lights .............80 flash to pass ..............................81 high beam ...........................13, 81 replacing bulbs .........................84 turning on and off ....................80 warning chime ..........................15 Heating heater only system ...................75 heating and air conditioning system .....................
Index Lumbar support, seats .............115 R M Radio ................................18, 43, 61 Radio reception ...........................74 Relays ........................................197 Remote entry system .......106, 108 illuminated entry ....................110 locking/unlocking doors ................................105, 107 panic alarm .............................108 replacement/additional transmitters .............................109 replacing the batteries ...........
Index Spare tire (see Changing the Tire) ...................................207–208 Spark plugs, specifications .............278, 284–285 Special notice ambulance conversions ..............7 utility-type vehicles ....................6 Specification chart, lubricants ...........................282, 284 Speed control ..............................93 Speedometer ...............................17 Starting your vehicle .......151–152, 154 jump starting ..........................213 Steering wheel controls ......
