Contents Before driving Introduction 2 Instrumentation 6 Controls and features Seating and safety restraints 25 101 Starting and driving Starting 137 Driving 141 Roadside emergencies 170 Servicing Maintenance and care 191 Capacities and specifications 229 Index 239 All rights reserved.
Introduction ICONS Indicates a safety alert. Read the following section on Warnings. Indicates vehicle information related to recycling and other environmental concerns will follow. Correct vehicle usage and the authorized disposal of waste cleaning and lubrication materials are significant steps towards protecting the environment. Indicates a message regarding child safety restraints. Refer to Seating and safety restraints for more information.
Introduction SPECIAL NOTICES Notice to owners of four wheel drive (4WD) vehicles 4WD vehicles have a significantly higher rollover rate than other types of vehicles. Before you drive your vehicle, please read this Owner’s Guide carefully. As with other vehicles of this type, failure to operate this vehicle correctly may result in loss of control or an accident. Be sure to read Driving off road in the Driving chapter.
Introduction These are some of the symbols you may see on your vehicle.
Introduction Vehicle Symbol Glossary Child Safety Door Lock/Unlock Interior Luggage Compartment Release Symbol Panic Alarm Engine Oil Engine Coolant Engine Coolant Temperature Do Not Open When Hot Battery Avoid Smoking, Flames, or Sparks Battery Acid Explosive Gas Fan Warning Power Steering Fluid Maintain Correct Fluid Level Emission System Engine Air Filter Passenger Compartment Air Filter Jack MAX MIN Check fuel cap 5
Instrumentation Audio system (pg. 47) 4wd control (pg. 15) * if equipped 6 Message center (pg. 153) Climate controls (pg. 28) Turn signal and wiper/washer control (pg.
Instrumentation Instrument cluster (pg. 8) Headlamp control (pg. 25) Instrument panel dimmer control (pg. 26) Reverse sensing system* (pg. 26) Driver air bag (pg. 120) Cruise control (pg. 69) Steering wheel controls* (pg.
Instrumentation WARNING LIGHTS AND CHIMES Service engine soon Illuminates briefly to ensure the system is functional. If it comes on after the engine is started, one of the engine’s emission control systems may be malfunctioning. The light may illuminate without a driveability concern being noted. The vehicle will usually be drivable and will not require towing. If the light remains on, have your vehicle serviced at the first available opportunity.
Instrumentation Air bag readiness The supplementary restraint system includes the air bags and seat belt buckle pretensioners. The warning momentarily illuminates when the ignition is turned to the ON position. If the light fails to illuminate, continues to flash or remains on, have the system serviced immediately. Seat belt Momentarily illuminates when the ignition is turned to the ON position to remind you to fasten your seat belts. For more information, refer to the Seating and safety restraints chapter.
Instrumentation Turn signal Illuminates when the left or right turn signal or the hazard lights are turned on. If one or both of the indicators stay on continuously or flash faster, check for a burned-out turn signal bulb. Refer to Bulbs in the Maintenance and care chapter. High beams Illuminates when the high beam headlamps are turned on. Low washer fluid (if equipped) Illuminates when the windshield washer fluid is low.
Instrumentation O/D off (if equipped) Illuminates when the transmission control switch (TCS) has been pushed turning the transmission overdrive function OFF. When the light is on, the transmission does not operate in the overdrive mode, refer to the Driving chapter for transmission function and operation. The light may also flash steadily if a transmission malfunction is detected.
Instrumentation GAUGES 4X4 LOW 4X4 HIGH Speedometer Indicates the current vehicle speed. Engine coolant temperature gauge Indicates the temperature of the engine coolant. At normal operating temperature, the needle remains within the normal area (the indicated area between the “H” and “C”). If it enters the red section, the engine is overheating. Stop the vehicle as soon as safely possible, switch off the engine immediately and let the engine cool.
Instrumentation This gauge indicates the temperature of the engine coolant, not the coolant level. If the coolant is not at its proper level the gauge indication will not be accurate. Odometer Registers the total kilometers (miles) of the vehicle. Refer to Electronic Message Center for information on how to switch the display from metric to English measurements. Trip odometer Registers the kilometers (miles) of individual journeys. To reset, depress the control.
Instrumentation Battery voltage gauge Indicates battery voltage. If the pointer moves and stays outside the normal operating range, have the vehicle’s electrical system checked as soon as possible. Engine oil pressure gauge Indicates the engine oil pressure when the engine is operating. If the gauge indicates zero or very low oil pressure (needle drops below “L”) stop the vehicle and engine as soon as safe to do so and check the engine oil level.
Instrumentation Fuel gauge Displays approximately how much fuel is in the fuel tank (when the key is in the ON position). The fuel gauge may vary slightly when the vehicle is in motion or on a grade. The ignition should be in the OFF position while the vehicle is being refueled. When the gauge first indicates empty, there is a small amount of reserve fuel in the tank.
Instrumentation Selectable features Reset Press this control to select and reset functions shown in the INFO menu and SETUP menu. Info menu This control displays the following control displays: • Odometer • Trip odometer/Odometer • Distance to Empty • Average Fuel Economy Odometer/Trip odometer Refer to Gauges in this chapter. Compass display The compass reading may be affected when you drive near large buildings, bridges, power lines and powerful broadcast antenna.
Instrumentation Most geographic areas (zones) have a magnetic north compass point that varies slightly from the northerly direction on maps. This variation is four degrees between adjacent zones and will become noticeable as the vehicle crosses multiple zones. A correct zone setting will eliminate this error. Refer to Compass zone/calibration adjustment. Compass zone/calibration adjustment Perform this adjustment in an open area free from steel structures and high voltage lines.
Instrumentation 8. Press the RESET control to start the compass calibration function. 9. Slowly drive the vehicle in a circle (less than 5 km/h [3 mph]) until the CIRCLE SLOWLY TO CALIBRATE indicator changes to CALIBRATION COMPLETED. This will take up to three circles to complete calibration. 10. The compass is now calibrated. AVERAGE FUEL ECONOMY (AFE) Select this function from the INFO menu to display your average fuel economy in liters/100 km or miles/gallon.
Instrumentation DISTANCE TO EMPTY (DTE) Selecting this function from the INFO menu will give you an estimate of how far you can drive with the fuel remaining in your tank under normal driving conditions. Remember to turn the ignition OFF when refueling your vehicle. Otherwise, the display will not show the addition of fuel for a few kilometers (miles). The DTE function will display LOW FUEL LEVEL and sound a tone for one second when you have low fuel level indicated on the fuel gauge.
Instrumentation Units (English/Metric) 1. Select this function from the SETUP menu for the current units to be displayed. 2. Press the RESET control to change from English to Metric. System check Selecting this function from the SETUP menu causes the message center to cycle through each of the systems being monitored. For each of the monitored systems, the message center will indicate either an OK message or a warning message for three seconds.
Instrumentation System warnings System warnings alert you to possible problems or malfunctions in your vehicle’s operating systems. In the event of a multiple warning situation, the message center will cycle the display to show all warnings by displaying each one for four seconds. The message center will display the last selected feature if there are no more warning messages.
Instrumentation CHECK ENGINE TEMP. Displayed when the engine coolant is overheating. Stop the vehicle as soon as safely possible, turn off the engine and let it cool. Check the coolant and coolant level. Refer to Engine coolant in the Maintenance and care chapter. If the warning stays on or continues to come on, contact your Ford Dealer as soon as possible. CHECK CHARGING SYSTEM. Displayed when the electrical system is not maintaining proper voltage.
Instrumentation To reset the oil monitoring system to 100% after each oil change (approximately 15,000 km or 12 months) perform the following: 1. Press the SETUP control to access the system check function. 2. Press and release the RESET control to display “OIL LIFE XX% HOLD RESET NEW”. 3. Press and hold the RESET control for 2 seconds to display “IF NEW OIL HOLD RESET”. 4. Press and hold the RESET control to display “OIL LIFE SET TO 100%”. Your oil life is now reset.
Instrumentation 4. Release the RESET control momentarily, then press RESET and SETUP controls at the same time to activate a service mode which will display “OIL LIFE XX% RESET TO ALTER”. 5. Press RESET until you find your personalized OIL LIFE XX%. 6. With your personalized OIL LIFE XX% displayed, press SETUP to continue the system check. LOW WASHER FLUID LEVEL. Indicates the washer fluid reservoir is less than one quarter full. Check the washer fluid level.
Controls and features HEADLAMP CONTROL Rotate the headlamp control clockwise to the first position to turn on the parking lamps. Rotate clockwise to the second position to also turn on the headlamps. A High beams • Push forward to activate. • Pull toward you to deactivate. Activating the high beam will also activate the driving lamps. Headlight flasher Pull toward you to activate and release to deactivate.
Controls and features PANEL DIMMER CONTROL Use to adjust the brightness of the instrument panel during headlamp and parklamp operation. • Rotate up to brighten. • Rotate down to dim. • Rotate to full up position (past detent) to turn on interior lamps. • Rotate to full down position (past detent) to turn off interior lamps. AUTOLAMP CONTROL (IF EQUIPPED) The autolamp system provides light sensitive automatic on-off control of the exterior lights normally controlled by the headlamp control.
Controls and features To help avoid personal injury, please read and understand the limitations of the reverse sensing system as contained in this section. Reverse sensing is only an aid for some (generally large and fixed) objects when moving in reverse on a flat surface at “parking speeds”. Inclement weather may also affect the function of the RSS; this may include reduced performance or a false activation. To help avoid personal injury, always use caution when in R (Reverse) and when using the RSS.
Controls and features The RSS is automatically enabled when the gear selector is placed in R (Reverse) and the ignition is ON. The RSS control allows the driver to disable the RSS only when the ignition is ON, and the gear selector is in R (Reverse). The OFF indicator remains illuminated when the system is disabled. The system defaults to ON every time R (Reverse) is selected. Press the control to disable or enable the system. The indicator will remain illuminated to indicate a failure of the RSS.
Controls and features In and , if the outside temperature is about 6°C (43°F) or higher, the air conditioner will automatically dehumidify the air to reduce fogging. However, the A/C indicator will not illuminate. When placed in MAX A/C, the A/C indicator will illuminate automatically and cannot be manually disabled. Fan speed and recirculated/outside air control Controls the volume of air circulated in the vehicle and the 2 recirculated/outside air option 3 associated with the mode selector control.
Controls and features • • • • • • (Panel)-Distributes outside or recirculated air through the instrument panel registers. Push the A/C control in order to cool the vehicle below the outside temperature. For added customer comfort, the system will allow some airflow through the floor ducts in this mode. (Panel and floor)-Distributes outside or recirculated air through the instrument panel registers and floor ducts. Push the A/C control in order to cool the vehicle below the outside temperature.
Controls and features In order to cool your vehicle using outside air: , or . 1. Turn the mode selector to . (The indicator light will illuminate.) 2. Press 3. Turn the temperature control knob to the left. 4. Turn the fan speed control to the position of your choice . within During periods of high humidity, vapor may be emitted from the air outlets when using the A/C system with outside air. This can be corrected by using to cool the vehicle.
Controls and features Operating tips • In humid weather, place the climate control system in before driving. This will reduce fogging of the windshield. Once the windshield has cleared, operate the climate control system as desired. • To reduce humidity buildup inside the vehicle in cold weather conditions, do not drive with the climate control system in the OFF or position.
Controls and features 4. Set the fan speed and recirculated/fresh air control to position 4 of 5. Direct the outer panel vents towards the side windows 6. To increase airflow to the outer panel vents, close the central panel vents. Do not place objects on top of the instrument panel, as these objects may become projectiles in a collision or sudden stop. • Defrost control — Refer to Rear Window Defroster.
Controls and features Turning the DEATC system on Press AUTO, any of the override controls, the fan speed control, or either of the temperature selection controls. The DEATC system will only operate when the ignition is in the ON position. Turning the DEATC system off Press OFF. The outside temperature (EXT) function (if selected) will continue to operate until the ignition is turned off.
Controls and features DEATC automatic operation When in AUTO mode, the DEATC system automatically controls the air conditioning operation, the fan speed, the airflow direction and determines whether outside or recirculated air is required. Press AUTO and select the desired temperature. The selected temperature will appear in the display window, and an indicator above the AUTO control will light. The DEATC system will either heat or cool the vehicle to achieve the selected temperature.
Controls and features Single/dual electronic temperature zone Press DUAL to enable or disable the dual zone temperature feature. When DUAL is pressed, the display window indicates the current temperature setting for the driver and the last temperature setting that was selected for the passenger. In addition to the DUAL control, the passenger may engage the dual temperature zone feature by pressing the passenger side temperature control.
Controls and features Passenger side temperature selection To control the temperature, select any temperature between 16°C (60°F) and 32°C (90°F) by pressing the temperature control on the passenger side of the system. Temperature conversion Press the Fahrenheit/Celsius (°F °C) EXT control to switch between Fahrenheit and Celsius temperature , FC on the DEATC display only. The temperature in Celsius will be displayed in half-degree increments.
Controls and features Fan speed ( ) When AUTO is pressed, fan speed is adjusted automatically for existing conditions. You can override fan speed at any time. To control fan speed manually, press the fan control to cancel the automatic fan speed operation. Press the control up for higher fan speed or down for lower and a bar graph to indicate manual fan speed. The display will show fan operation and relative speed.
Controls and features (ON) the indicator will be lit. When manual A/C is selected (OFF) the indicator will not be lit. In and , if the outside temperature is about 6°C (43°F) or higher, the air conditioner will automatically dehumidify the air to reduce fogging. However, the A/C indicator will be off and the A/C override control cannot be selected. The air conditioning compressor can operate in all modes except OFF.
Controls and features When AUTO is selected, the recirculated air feature operates automatically for existing conditions. However, the air recirculation indicator will not be lit. If the recirculated air is selected while in AUTO operation, the DEATC system will be disabled and you will return to manual operation with the recirculated air indicator lit and with the A/C operating. To return to automatic recirculated air operation, press AUTO.
Controls and features (panel/floor) — Distributes air through the instrument panel registers and the front seat floor ducts. For added customer comfort, the air distributed through the floor ducts may be slightly warmer than the air sent to the instrument panel registers. (floor) — Distributes air through the front seat floor ducts. The system will allow some airflow out the window defroster ducts and the demister outlets.
Controls and features Displaying outside temperature Press EXT to display the outside air temperature. It will remain selected until the EXT control is pressed again. If the driver or passenger temperature or the fan speed is changed, or modes are selected while the outside temperature is the AUTO or displayed, the driver and passenger temperature display will be displayed for 4 seconds. Following this, the outside temperature display will return to the window.
Controls and features • Under normal weather conditions, your vehicle’s climate control system should be left in any position other than OFF or when the vehicle is parked. This allows the vehicle to “breathe” through the outside air inlet duct. • Under snowy or dirty weather conditions, your vehicle’s climate control system should be left in the OFF position when the vehicle is parked. This allows the climate control system to be free from contamination of outside pollutants.
Controls and features Auxiliary climate controls (if equipped) Your vehicle may be equipped with auxiliary climate controls which are located in the overhead console of the first row and in the headliner for second row seating. The auxiliary climate control feature provides increased capacity to quickly heat or cool your vehicle. If your vehicle is equipped with a manual heating and air conditioning system, the auxiliary climate controls are dependent on the main climate control system.
Controls and features Press the mode selector once to select air distribution through the overhead vents. The icon will illuminate on the temperature selector. Press the mode selector again to select air distribution through the floor vents. The icon will illuminate on the temperature selector. Only the auxiliary control head (front or rear) that is active will have the indicator lights functioning.
Controls and features Turn the temperature control to regulate the air temperature. Press the mode selector once to select air distribution through the overhead vents. The icon will illuminate on the temperature selector. Press the mode selector again to select air distribution through the floor icon will illuminate on the temperature selector. Only the vents. The auxiliary control head (front or rear) that is active will have the indicator lights functioning.
Controls and features 4WD CONTROL This control operates the 4WD. Refer to Control trac automatic four-wheel drive system in the Driving chapter for more information. 4X4 Auto 4X4 High 4X4 Low USING YOUR AUDIO SYSTEM 6006 AM/FM Sound System with 6–Disc In Dash Changer On 6006 units: if power has been disconnected, then reconnected, the unit will check for the presence of discs in the magazine.
Controls and features Anti-theft protection panel To deter would-be thieves, Ford audio units have a removable front panel without which the unit will not work. Avoid touching the contacts on the back of the panel and do not use excessive force to refit it. Press the security release control and remove the front panel. To reposition the panel, insert the right-hand edge first, then the left-hand side, until the retaining latch is engaged.
Controls and features Recording the keycode You will be provided with a keycode card when you take delivery of your vehicle. Keep the card in a safe place, but not inside your vehicle. If you lose the keycode, contact your Ford Dealer and supply details of your audio unit along with some proof of identity. To enter a keycode If you turn on the audio unit and CODE flashes in the display, you must enter a keycode before the unit is operational. Use the station preset controls to enter your keycode. 1.
Controls and features • If LOCK 10 appears, the unit is permanently inoperative. Contact your local Ford dealer for help and advice. • If LOCKED appears, the unit is permanently inoperative. Contact your local Ford Dealer for help and advice. 10 Volume/power control Press the control to turn the audio system on or off. Turn the control to raise or lower volume. This control can also operate the audio system for up to one hour with the ignition turned off.
Controls and features Automatic volume control (AVC) (if equipped) With this feature, radio volume changes automatically with vehicle speed to compensate for road and wind noise. The display will show the level selected. The greater the number selected, the higher the level of compensation. 1. Press the MENU control until AVC appears in the display. 2. Use the SEEK control to adjust the volume. on the SEEK control to 3. Press increase volume compensation 4.
Controls and features Seek function in radio mode • Press to find the next station up the frequency band. • Press to find the next station down the frequency band. Seek function in CD mode Press to select the next track on the current disc. Press and hold the to return to the beginning of the current track being played. Press twice rapidly to select the previous track. Scan function The scan function works in radio and CD modes.
Controls and features SCN will appear in the display and each track will be played for a few seconds. Press the SEEK control again to disengage the scan function and continue listening to a track. 1 2 SCN will flash in the display and each track will be played for a few seconds. Press the SEEK control again to disengage the scan function and continue listening to a track. Treble adjust The treble adjust control allows you to increase or decrease the audio system’s treble output. Press the TREB control.
Controls and features Press the BASS control. Turn the volume control (VOL) up or down to the desired setting. The display will indicate the level selected. Speaker fade adjust The fade function allows speaker sound to be adjusted between the front and rear speakers. Press the FADE control to activate the fade function. Turn the volume (VOL) control to adjust the sound from the front speakers to the rear speakers.
Controls and features The display will indicate the level selected. Speaker balance adjust The speaker balance function allows the sound distribution to be adjusted between the right and left speakers. Press the BAL control to engage the speaker balance function. Turn the volume (VOL) control to adjust the sound between the right and left speakers. The display will indicate the level selected.
Controls and features Station memory preset controls Your audio system is equipped with six station memory preset controls. These controls can be used store up to 24 preset frequencies (total) between AM (LW and MW), FM1, FM2 and the AutoStore bands. Setting memory preset stations 1. Select the frequency band with the AM/FM select control. 2. Select a station. Refer to Tune adjust or Seek function for more information on selecting a station. 3.
Controls and features Stereo indicator The stereo indicator appears in the display whenever a stereo signal is received. In poor signal conditions, the indicator will flicker and then go out when the signal is lost. CD select Press the CD control to engage CD mode. CD playback will begin. (Radio reception will be interrupted whenever a CD is inserted in to the audio unit.) If two or more CDs are loaded one after the other, playback will begin with the last CD loaded.
Controls and features Disc selection To select a disc, press the preset control that corresponds to the desired disc. The display will indicate the CD selected. During playback, the display normally indicates the elapsed time. If the track is longer than the display allows, the first digit will flash while the rest of the numbers return to zero and begin counting again. CDs and tracks are selected and played chronologically. Disc one will follow disc six.
Controls and features NO DISCS will appear in the display if the CD control is pressed and there are no discs loaded. Tune adjust The tune adjust feature allows you to manually adjust the waveband tuning in radio mode. Tune adjust in radio mode Press the MENU control until MAN appears in the display. on the SEEK control to Press move up the frequency up the band in manual increments. Press on the SEEK control to move down the band in manual increments.
Controls and features Fast forward/reverse feature Press and momentarily hold on the SEEK control to fast forward. Press and momentarily hold on the SEEK control to reverse. Loading Cds 6006 units are designed to play commercially pressed 12cm audio compact discs only. Due to technical incompatibility, certain recordable and re-recordable compact discs may not function correctly when used in Ford CD players.
Controls and features 4. LOAD and a disc icon will flash in the display. The CD will be loaded into the first available location. 5. Playback will begin automatically and the preset number will appear in one of the disc icons to confirm the location. Loading more than one CD 1. Press and hold the LOAD control. LOAD 2. LOAD all will appear in the display. 3. When the display changes to INSERT and the lights flash in the CD entry slot, the system is ready to accept a disc.
Controls and features 4. LOAD and a disc icon will flash in the display. Once the disc is loaded, the display will change to WAIT and then INSERT to confirm that another CD may be loaded. Up to six CDs may be loaded. 5. The display will indicate FULL if six CDs are loaded and the LOAD control is pressed again. CD eject during playback 1. Press the eject control during CD playback to eject the CD. Press the control again to cancel the eject process. 2.
Controls and features To eject a disc during radio reception 1. Press the EJ control. 2. SELECT CD will be displayed. 3. Press the preset control that corresponds to the desired disc. 4. REMOVE will appear in the display and the disc will be held ready for removal.
Controls and features To eject all discs 1. Press and hold the EJ control. 2. EJECT ALL will appear in the display. The display will alternate between EJECT and REMOVE. 3. When REMOVE is displayed, take the disc out of the unit. This process will repeat until all of the discs have been removed. Track compression feature Compression adjust brings soft and loud CD passages together for a more consistent listening level. Press the MENU control repeatedly until the COMP display appears.
Controls and features The display will indicate the compression feature is engaged during playback. Random track playback (SHUF) Press the MENU control repeatedly until the SHUF display appears. Use the SEEK control to engage or disengage the feature. With the function engaged, the elapsed time indicator is replaced by SHUF as a new track is selected. Audio distortion reduction (CLIP) Press and hold the MENU control until the display changes.
Controls and features With the feature activated, the audio unit automatically detects sound distortion and reduces the volume level until the distortion has been eliminated. Due to this, when the CLIP function is engaged and the volume is adjusted, there may not be an increase in sound. Setting the clock Press the CLK control. Press the SEEK control to highlight the hours/minutes respectively. Use the volume control to set both the hours and minutes.
Controls and features Troubleshooting the CD changer (if equipped) The laser beam used in the compact disc player is harmful to the eyes. Do not attempt to disassemble the case. If sound skips: • You may be traveling on a rough road, playing badly scratched discs or the disc may be dirty. Skipping will not scratch the discs or damage the player. If your changer does not work, it may be that: • A disc is already loaded where you want to insert a disc. • The disc is inserted with the label surface downward.
Controls and features Radio reception The following tips will help you gain the best reception from your high quality Ford audio system. To gain the best reception, always tune to the strongest station signal available. AM medium/long wave reception Under most conditions, strong MW and LW signals provide stable sound quality and little signal disturbance. However, at night, atmospheric conditions may sometimes lead to interference from foreign stations.
Controls and features POSITIONS OF THE IGNITION 1. OFF/LOCK, shuts off the engine 3 and all accessories/locks the steering wheel, gearshift lever and allows key 2 removal. 4 2. ACC, allows the electrical accessories such as the radio to operate while the engine is not running. 1 3. ON, all electrical circuits operational. Warning lights illuminated. Key position when driving. 4. START, cranks the engine. Release the key as soon as the engine starts. CRUISE CONTROL To turn cruise control on • Press ON.
Controls and features To turn cruise control off • Press OFF • NOTE: Turning off the vehicle ignition will automatically turn off the cruise control. Once cruise control is switched off, the previously programmed set speed will be erased. To set a speed • Press SET+. For cruise control to operate, the cruise control must be ON and the vehicle speed must be greater than 48 km/h (30 mph).
Controls and features The cruise control system may not be able to maintain the set speed in certain circumstances (eg. driving up steep hills). If the vehicle speed drops below the set speed by 16 km/h (10 mph), the cruise control system may automatically disengage. You may need to use the accelerator pedal to maintain vehicle speed under these circumstances. Do not use the cruise control in heavy traffic or on roads that are winding, slippery, or unpaved.
Controls and features To set a lower set speed • Press and hold COAST/CST −. Release the control when the desired speed is reached or • Press and release COAST/CST − to operate the Tap-Down function. Each press will decrease the set speed by 1.6 km/h (1 mph) or RES SET + COAST • Depress the brake pedal. When the desired vehicle speed is reached, press SET +.
Controls and features To disengage cruise control • Depress the brake pedal or • Depress the clutch pedal (if equipped). Disengaging the cruise control will not erase the previously programmed set speed. Pressing OFF will erase the previously programmed set speed.
Controls and features To return to a previously set speed • Press RES. For RES to operate, the vehicle speed must be faster than 48 km/h (30 mph). RES SET + COAST Indicator light This light comes on when the vehicle cruise control is engaged and actively controlling vehicle speed. TILT STEERING COLUMN Pull the lever down to unlock the tilt steering column. While the lever is in the down position, tilt the steering column to the desired orientation.
Controls and features Lift the lever back to its original position to lock the steering column. Never adjust the steering column when the vehicle is moving. HAZARD FLASHER For information on the hazard flasher control, refer to Hazard flasher in the Roadside emergencies chapter. WINDSHIELD WIPER/WASHER CONTROLS Rotate the windshield wiper control to the desired interval, low or high speed position. The bars of varying length are for intermittent wipers.
Controls and features Push (tap) the end of the stalk briefly for a single swipe (no wash). Push and hold for three swipes with wash. Push and hold for a longer wash (up to ten seconds). Speed dependent wipers When the windshield wiper control is set on the intermittent settings, speed-sensitive front wipers automatically adjust as the vehicle’s speed changes. Rear window wiper/washer controls For rear wiper operation, rotate the rear window wiper and washer control to the desired position.
Controls and features STEERING WHEEL CONTROLS (IF EQUIPPED) These controls allow you to operate some radio and climate control features. Audio control features to select AM, FM1, FM2, Press TAPE (if equipped), or CD (if equipped). In AM, FM1, or FM2 mode: • Press MEM to select preset stations within the selected radio band. In Tape mode: • Press MEM to select the next selection on the tape. In CD mode: • Press MEM to select the next selection on the CD. In any mode: • Press VOL + or − to adjust volume.
Controls and features Climate control features Press TMP + or - to adjust temperature. Press + or - to adjust fan speed. OVERHEAD CONSOLE (IF EQUIPPED) The appearance of your vehicle’s overhead console will vary according to your option package. Interior Lamps Dome lamps and map lamps The front map/dome lamp is located overhead between the driver and the passenger seats (5 seater vehicles) or above the second row seat (7 seater vehicles).
Controls and features The map lamp controls are located on the dome lamp. Press the controls on either side of each lens on each map lamp to activate the lamps. All vehicles are equipped with a cargo lamp, which is located overhead in the rear cargo area and above the third row seat (if equipped). The dome lamp will stay on if the control is moved to the driver’s side position. When the control is in the middle position, the lamp will only come on when a door is opened.
Controls and features ILLUMINATED VISOR MIRROR To turn on the visor mirror lamps, lift the mirror cover. POWER WINDOWS Press and hold the rocker switches to open and close windows. • Press the top portion of the rocker switch to close. AUTO • Press the bottom portion of the rocker switch to open.
Controls and features One touch down • Press AUTO completely down and release quickly. The driver’s window will open fully. One touch down can be deactivated during operation by pushing down on the top part of the driver power window control. AUTO Window lock The window lock feature allows only the driver to operate the power windows. To lock out all the window controls except for the driver’s press the left side of the control. Press the right side to restore the window controls.
Controls and features POWER DOOR LOCKS Press control to unlock all doors. Press control to lock all doors. POWER DOOR LOCK/UNLOCK INHIBIT If the interior trim switch does not operate, see the Perimeter alarm system in this section for more details. LIFTGATE An additional power door lock can be accessed by opening the liftgate. The button is located either on the top of the left-hand quarter trim panel underneath the rear window, or on the bottom of the left-hand quarter trim panel.
Controls and features CHILDPROOF DOOR LOCKS When these locks are set, the rear doors cannot be opened from the inside. The rear doors can be opened from the outside when the doors are unlocked. The childproof locks are located on rear edge of each rear door and must be set separately for each door. Setting the lock for one door will not automatically set the lock for both doors. Move lock control up to engage the childproof lock. Move control down to disengage childproof locks.
Controls and features Fold-away mirrors Pull the side mirrors in carefully when driving through a narrow space, like an automatic car wash. CENTER CONSOLE Your vehicle may be equipped with a variety of console features. These include: • Utility compartment with cassette/compact disc storage • Auxiliary power point • Cupholders • Tissue box holder Use only soft cups in the cupholder. Hard objects can injure you in a collision. Auxiliary power point Power outlets are designed for accessory plugs only.
Controls and features Rear auxiliary power point A second auxiliary power point is located on the rear side of the console. It is accessible from the rear seats.
Controls and features POSITIVE RETENTION FLOOR MAT Position the floor mat so that the eyelet is over the pointed end of the retention post and rotate forward to lock in. Make sure that the mat does not interfere with the operation of the accelerator or the brake pedal. To remove the floor mat, reverse the installation procedure. Ensure that the floor mats do not sit under the accelerator or brake pedals. Loss of control may result from improperly positioned floor mats.
Controls and features • To open the liftgate window, press the control on the remote entry key fob or, with the liftgate unlocked, push the control button on the right side under the license plate lamp shield. • To open the liftgate, unlock the liftgate (with the power door locks, the remote entry or the keyless entry pad) and pull the middle lever under the license plate lamp shield.
Controls and features CARGO COVER (IF EQUIPPED) Your vehicle may be equipped with a cargo area cover that covers the luggage compartment of your vehicle. To install the cover: Push both ends of the cover into the depressions (right side first) in the trim panels behind the second row seat. To reduce the risk of injuries, the cargo area cover must be properly installed on the rear trim panels. Do not place any objects on the cargo area cover.
Controls and features 2. Wrap the vinyl around the roller tube twice. Tuck the edges of the vinyl inside the end cap with each wrap. 3. Fold the edges of the vinyl towards the center, making sure that the edges clear the end cap slots. Use tape or a rubber band to hold the vinyl to the left side of the tube. 4. Push in the right end cap (marked RH) about 1⁄4 of the total length to disengage the clutch and hold the end cap in while turning the roller tube toward you 14 times. 5. Let go of the right end cap.
Controls and features Cargo management system The cargo management system consists of storage compartments located in the floor of the rear cargo area. 7 passenger stowage: 1. To open, lift the release handle and the lid. 2. To close, lower the lid, lift the release handle and press down on the lid. 5 passenger stowage: When the lid is open, it will stand up on its own. The lid can be detached from the vehicle and used as a knee pad (carpet side up) for changing a tire. 1.
Controls and features Unlocking the doors/liftgate Press this control to unlock the driver’s door. The interior lamps will illuminate with the ignition OFF. Press the control a second time within three seconds to unlock all doors and liftgate. Locking the doors/liftgate Press this control to lock all doors and liftgate.
Controls and features Replacing the battery The remote transmitter is powered by one coin type three-volt lithium battery CR2032 or equivalent. Typical operating range will allow you to be up to 10 meters (33 feet) away from your vehicle. A decrease in operating range can be caused by the following factors: • Weather conditions • Nearby radio towers • Structures around the vehicle • Other vehicles parked next to the vehicle To replace the battery: 1.
Controls and features Programming remote transmitters It is necessary to have all (maximum of four — original and/or new) of your remote transmitters available prior to beginning this procedure. To program the transmitters yourself: • Insert a key in the ignition and 3 turn from 1 (LOCK) to 3 (ON) and cycle between 1 (LOCK) and 2 3 (ON) eight times in rapid succession (within 10 seconds) 4 with the eighth turn ending in the 3 (ON) position.
Controls and features The battery saver will shut off the interior lamps 10 minutes after the ignition has been turned to the OFF position.
Controls and features PERIMETER ALARM SYSTEM (IF EQUIPPED) The perimeter anti-theft system will help prevent your vehicle from unauthorized entry. If there is any potential perimeter anti-theft problem with your vehicle, ensure ALL key fobs (remote entry transmitters) are taken to your Ford Dealer, to aid in troubleshooting. Power door lock disable feature This feature will help protect your vehicle from unauthorized entry.
Controls and features The system is ready to arm whenever the key is removed from the ignition. The following actions will prearm the alarm system: • Press the remote entry lock control (all doors closed). • Locking the driver door using the key in the key cylinder (all doors closed). There is a 20 second countdown when any of the actions listed above occur before the vehicle becomes ARMED.
Controls and features • Press the liftgate window control on the remote entry transmitter. The liftgate and liftgate window are no longer armed, but the doors and hood are still armed. To disarm the doors and hood, press the liftgate power door lock control. Pressing the power door unlock control within the 20 second prearmed mode will return the vehicle to a disarmed state. Triggering the anti-theft system The armed system will be triggered if: • Switching the ignition from OFF to RUN.
Controls and features THEFT INDICATOR The theft indicator is located on top of the instrument panel. • When the ignition is in the OFF position, the indicator will flash once every 2 seconds to indicate the SecuriLocky system is functioning as a theft deterrent. • When the ignition is in the ON position, the indicator will glow for 3 seconds to indicate normal system functionality.
Controls and features • A second key on the same key ring as the coded key If any of these items are present, you need to keep these objects from touching the coded key while starting the engine. These objects and devices cannot damage the coded key, but can cause a momentary “no start” condition if they are too close to the key during engine start. If a problem occurs, turn ignition OFF and restart the engine with all other objects on the key ring held away from the ignition key.
Controls and features 1. Insert the first previously 3 programmed coded key into the ignition and turn the ignition from 2 2 (ACC) to 3 (ON) (maintain ignition in 3 (ON) for at least one second). 4 2. Turn ignition to 1 (LOCK) and remove the first coded key from the ignition. 1 3. Within ten seconds insert the second previously programmed coded key into the ignition and turn the ignition to 2 (ACC) then to 3 (ON) (maintain ignition in 3 (ON) for at least one second but no more than ten seconds). 4.
Seating and safety restraints SEATING Do not adjust the seats while the vehicle is moving. It is extremely dangerous to ride in the cargo area inside or outside the vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of the vehicle that is not fitted with seats and seat belts. Be sure everyone in your vehicle is in a seat and is using a safety belt properly.
Seating and safety restraints The head restraint should be centered at the back of the head for optimum head support in the event of an impact or collision. Do not center on the neck. Push control to lower head restraint. Adjusting the front manual seat Lift handle to move seat forward or backward. Pull lever up to adjust seatback.
Seating and safety restraints Adjusting the front power seat (if equipped) The control is located on the outboard side of the seat cushion. Press front to raise or lower the front portion of the seat cushion. Press rear to raise or lower the rear portion of the seat cushion. Press the control to move the seat forward, backward, up or down.
Seating and safety restraints Using the manual lumbar support Turn the lumbar support control toward the front of vehicle to move the lumbar support forward for more direct support. Turn the lumbar support control toward the rear of vehicle to move the lumbar support back for less direct support. REAR SEATS Folding down the outboard second row seats 1. Locate handle on the side of the seat cushion by the door (40/20/40 seats are shown). 2.
Seating and safety restraints Adjusting the 2nd row seat for E-Z Entry (if equipped) The E-Z Entry seat allows for easier entry and exit to and from the 3rd row seat. To enter the 3rd row seat: 1. Fold down the 2nd row seat. 2. Pull the handle all the way down until the seat releases from the floor and folds away. 3. To return the seat to a seating position, flip the seat into the upright position. 4. Make sure the seat is latched to the floor.
Seating and safety restraints To exit the 3rd row seat, pull the red access control lever up releasing the seat from the floor and rotate the seat up towards the front seat. Always latch the vehicle seat to the floor, whether the seat is occupied or empty. If not latched, the seat may cause injury during a sudden stop.
Seating and safety restraints Folding the middle 2nd row seat (If equipped) 1. Raise the head restraint and remove. 2. Place the head restraint under the front seat for storage. 3. Locate the lever on the side of the seatback. 4. Pull the lever up and push the seatback toward the front of the vehicle. 5. Press down on the top outboard area of the seatback until a click is heard. To return the seat back to the upright position: 1. Pull the lever and lift the seat back toward the rear of the vehicle. 2.
Seating and safety restraints When returning the seat back to its original position, ensure it is securely latched by attempting to pull it down again. An unlatched seat may become dangerous in the event of a sudden stop or collision. Do not store long or protruding objects which may become projected into the front seat in the event of a sudden stop or impact from behind.
Seating and safety restraints 4. Push the closeout panel forward over the space between the seats. It is extremely dangerous to ride in the cargo area inside or outside the vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of the vehicle that is not fitted with seats and seat belts. Be sure everyone in your vehicle is in a seat and is using a safety belt properly. To put seat in upright position: 1.
Seating and safety restraints 3. Pull the seat release lever located on top of the seatback while lifting the seatback into the upright position. 4. The seatback will latch into place. 5. Remove the head restraints stored under the second row passenger seats and return them to the original positions on the seat back. When returning the seatback to its original position, ensure that it is securely latched by attempting to pull it down again.
Seating and safety restraints WARNING ! Care should be taken to avoid contamination of the webbing with polishes, oils and chemicals, and particularly battery acid. Cleaning may safely be carried out using mild soap and water. The belt should be replaced if webbing becomes frayed, contaminated or damaged. WARNING ! It is essential to replace the entire assembly after it has been worn in a severe impact even if damage to the assembly is not obvious. WARNING ! Belts should not be worn with straps twisted.
Seating and safety restraints The wearing of seat belts is a mandatory requirement throughout Australia and New Zealand. Seat belts should be properly fastened and adjusted before the vehicle is driven. Adjust the driver’s seat to position before fastening the seat belt. Seat belts should be checked by an Authorized Ford Dealer or recognized repairer after an accident has occurred. It may be necessary to replace the belt.
Seating and safety restraints Seat belt buckle pretensioner The restraint system with buckle pretensioners in the front bucket seats provides additional protection in the event of a frontal collision. During a frontal collision, a mechanism in the seat belt buckle is triggered which pretensions the seat belt and helps reduce slack from the belt. The belt pretensioner is not triggered in the event of a minor frontal, side or rear collision.
Seating and safety restraints 2. To unfasten, push the release button and remove the tongue from the buckle. The front and rear outboard seat belts in the vehicle are combination lap and shoulder belts. The front passenger and rear seat outboard seat belts have two types of locking modes described below: Vehicle sensitive mode The vehicle sensitive mode is the normal retractor mode, allowing free shoulder belt length adjustment to your movements and locking in response to vehicle movement.
Seating and safety restraints How to use the automatic locking mode • Buckle the combination lap and shoulder belt. • Grasp the shoulder portion and pull downward until the entire belt is extracted. • Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the automatic locking mode.
Seating and safety restraints After any vehicle collision, the rear outboard seat belt system must be checked by a qualified technician to verify that the “automatic locking retractor” feature for child seats is still functioning properly. In addition, all seat belts should be checked for proper function. Lap belts Adjusting the 2nd row center lap belt (if equipped) The lap belt will adjust automatically.
Seating and safety restraints Front seat belt height adjustment Your vehicle has seat belt height adjustments for the driver and front passenger. Adjust the height of the shoulder belt so the belt rests across the middle of your shoulder. The seat belt must not lie across the neck. To lower the shoulder belt height, push the button and slide the height adjuster down. To raise the height of the shoulder belt, slide the height adjuster up. Pull down on the height adjuster to make sure it is locked in place.
Seating and safety restraints If... Then... The driver’s seat belt is buckled The seat belt warning light and before the ignition switch is turned indicator chime remain off. to the ON position... BeltMinder The BeltMinder feature is a supplemental warning to the seat belt warning function. This feature provides additional reminders to the driver that the driver’s seat belt is unbuckled by intermittently sounding a chime and illuminating the seat belt warning lamp in the instrument cluster. If...
Seating and safety restraints Deactivating/activating the BeltMinder feature Read steps 1 - 9 thoroughly before proceeding with the deactivation/activation programming procedure.
Seating and safety restraints 7. Confirmation of disabling BeltMinder is provided by flashing the seat belt warning light four times per second for three seconds. 8. Confirmation of enabling BeltMinder is provided by flashing the seat belt warning light four times per second for three seconds, followed by three seconds with the seat belt warning light off, then followed by flashing the seat belt warning light four times per second for three seconds again. 9.
Seating and safety restraints Because the system senses crash severity, some frontal collisions will not inflate the air bag. Air bags are not designed to inflate in rollover, rear, side or low-speed frontal crashes. The air bag will not deploy with the ignition switch in the OFF (1) position. OPERATION Sensors in the vehicle detect the degree of severity of a frontal impact. The air bags are designed to deploy if the collision suits the criteria for deployment.
Seating and safety restraints THE IMPORTANCE OF WEARING SEAT BELTS Seat belts must be worn by all vehicle occupants to be properly restrained and help reduce the risk of injury in a collision. Wearing a seat belt will: • help keep you in the proper position when the air bags inflate, • reduce the risk of harm in rollover, side, or rear impact collisions, • reduce the risk of harm in frontal collisions that are not severe enough to activate the air bags, • reduce the risk of being thrown from your vehicle.
Seating and safety restraints NEVER install any child restraint (e.g., baby capsule, child seat, or booster seat) in the front seat where a passenger air bag is fitted, as serious injury or death may result from the force of the inflating front passenger air bag. The rear seat is the safest place for children. Never place objects in front of you while you are seated in the front seat as injury may result from the object when it is forced toward you by the inflating air bag.
Seating and safety restraints If any of these things happen, even intermittently, have the SRS system checked by your Ford Dealer immediately. Air bag maintenance and servicing No maintenance of the system is required unless: • A warning light or warning tone indicates a fault or the air bags have been inflated. If the air bag system is not serviced when a warning is given, the air bags may not function properly in the event of a collision or may deploy unexpectedly.
Seating and safety restraints How does the Safety CanopyY system work? The design and development of the Safety Canopyy system included recommended testing procedures that were developed by a group of automotive safety experts known as the Side Airbag Technical Working Group. These recommended testing procedures help reduce the risk of injuries related to the deployment of side airbags (including the Safety Canopyy).
Seating and safety restraints The Safety Canopyy system is designed to activate when the vehicle sustains lateral deceleration sufficient to cause the side crash sensor to close an electrical circuit that initiates Safety Canopyy inflation or when a certain likelihood of a rollover event is detected by the rollover sensor. The Safety Canopyy mounted to the roof side-rail sheet metal, behind the headliner, above the first and second row seats.
Seating and safety restraints A difficulty with the system is indicated by one or more of the following: • The readiness light (same light as for front air bag system) will either flash or stay lit. • The readiness light will not illuminate immediately after ignition is turned on. • A series of five beeps will be heard. The tone pattern will repeat periodically until the problem and light are repaired.
Seating and safety restraints Only fit a “bull bar” to your vehicle which is compatible with the Air Bag Supplemental Restraint System in your vehicle. “Bull bars” which are not compatible with the Air Bag Supplemental Restraint System in your vehicle may cause your air bag to malfunction which could result in damage to your vehicle and injury to yourself or others and may void the vehicle’s compliance to Australian Design Rules and New Zealand Land Transport Rules.
Seating and safety restraints CHILD RESTRAINTS Infants and small children should be restrained at all times in an approved child restraint suited to your vehicle and which conforms to AS1754–1991, or NZS5411 / BS3254 / BSAU185 / BSAU202 for New Zealand. Be sure to read the instructions provided by the restraint manufacturer, or consult an approved Restraint Fitting Station. Your automobile club or local vehicle registration authority can provide location details of fitting stations.
Seating and safety restraints 2. Insert the belt tongue into proper the proper buckle (the buckle closest to the direction from which the tongue is coming) for that seating position until you hear a snap and feel the latch engage. Make sure the tongue is latched securely by pulling on it. 3. Tighten the lap portion of the seat belt. Pull the shoulder portion of the belt until it has been fully extended. 4. Press the child restraint firmly into the seat. Allow the belt to retract.
Seating and safety restraints 6. Then attach the child restraint attachment clip to the anchor fitting with reference to the following information. Child restraint fittings In five-seater vehicles, three factory installed child restraint anchor fittings are provided behind the seats as illustrated. In seven-seater vehicles, five factory installed child restraint anchor fittings are provided behind the seats as illustrated.
Seating and safety restraints 7 seater vehicle • Anchor fitting for 2nd row seats • Anchor fitting for 3rd row seats Child restraint anchorages are designed to withstand only those loads imposed by correctly fitted child restraints. Under no circumstances are they to be used for adult seat belts, harnesses, or for attaching other items or equipment to the vehicle.
Seating and safety restraints Anchorage locations The anchor fittings are provided on the floor at the rear of the vehicle as shown in these illustrations.
Seating and safety restraints • Behind 3rd row seats (for use with child restraints fitted to the 3rd row seat only) Attaching clip The diagrams below show the correct assembly and orientation of the attaching clip for anchor fittings. Always ensure that the attaching clip is properly engaged with the anchor fitting and that the upper tether strap length is adjusted to remove any slack. Remove the rear seat headrest where the anchor is being used.
Seating and safety restraints 5 seater vehicle 7 seater vehicle • for 2nd row seats 135
Seating and safety restraints • for 3rd row seats 136
Starting PREPARING TO START YOUR VEHICLE Engine starting is controlled by the powertrain control system. When starting a fuel-injected engine, avoid pressing the accelerator before or during starting. Only use the accelerator when you have difficulty starting the engine. For more information on starting the vehicle, refer to Starting the engine in this chapter.
Starting 2. Make sure the parking brake is set. 3. Make sure the gearshift is in P (Park) position (for vehicles equipped with an automatic transmission) or in N (Neutral) with the clutch pedal depressed (for vehicles equipped with a manual transmission). 4. Turn the key to 3 (ON) without 3 turning the key to 4 (START). If there is difficulty in turning the 2 key, firmly rotate the steering wheel 4 left and right until the key turns freely.
Starting STARTING THE ENGINE Note: Whenever you start your vehicle, release the key as soon as the engine starts. Excessive cranking could damage the starter. 1. Turn the key to 4 (START) 3 without pressing the accelerator pedal and release as soon as the 2 engine starts. The key will return to 3 (ON). 4 2. If the engine does not start within five seconds, wait 10 seconds and try again. 1 3.
Starting Guarding against exhaust fumes Although odorless and colorless, carbon monoxide is present in exhaust fumes. Take precautions to avoid its dangerous effects. If you ever smell exhaust fumes of any kind inside your vehicle, have your Ford Dealer inspect and fix your vehicle immediately. Do not drive if you smell exhaust fumes. These fumes are harmful and could kill you. Have the exhaust and body ventilation systems checked whenever: • the vehicle is raised for service.
Driving BRAKES Your service brakes are self-adjusting. Refer to the Service Guide for scheduled maintenance. Occasional brake noise is normal and often does not indicate a performance concern with the vehicle’s brake system. In normal operation, automotive brake systems may emit occasional or intermittent squeal or groan noises when the brakes are applied.
Driving The ABS operates by detecting the onset of wheel lockup during brake applications and compensates for this tendency. The wheels are prevented from locking even when the brakes are firmly applied. The accompanying illustration depicts the advantage of an ABS equipped vehicle (on bottom) to a non-ABS equipped vehicle (on top) during hard braking with loss of front braking traction.
Driving There are two important rules when braking in emergencies with ABS: 1. Apply full force on the brake pedal. 2. Steer around the obstacle. No matter how hard you brake, steering control is maintained. Pedal propulsion coupled with noise while breaking under panic conditions or on loose gravel, bumps, wet or snowy roads is normal and indicates proper functioning of the vehicle’s anti-lock brake system.
Driving The BRAKE warning lamp in the instrument cluster illuminates and remains illuminated (when the ignition is turned ON) until the parking brake is released. The parking brake is not recommended to stop a moving vehicle. However, if the normal brakes fail, the parking brake can be used to stop your vehicle in an emergency. Since the parking brake applies only the rear brakes, the vehicle’s stopping distance will increase greatly and the handling of your vehicle will be adversely affected.
Driving If the steering wanders or pulls, the condition could be caused by any of the following: • Underinflated tire(s) on any wheel(s) • Uneven vehicle loading • High crown in center of road • High crosswinds • Wheels out of alignment • Loose or worn suspension components PREPARING TO DRIVE YOUR VEHICLE Four-wheel drive vehicles have a significantly higher rollover rate than other types of vehicles.
Driving AUTOMATIC TRANSMISSION OPERATION (IF EQUIPPED) Brake-shift interlock This vehicle is equipped with a brake-shift interlock feature that prevents the gearshift lever from being moved from P (Park) when the ignition is in the ON position unless the brake pedal is depressed. If you cannot move the gearshift lever out of P (Park) with the ignition in the ON position and the brake pedal depressed: 1. Apply the parking brake, turn the ignition key to LOCK, then remove the key. 2.
Driving 4. Insert an implement (eg. a screwdriver) into the access hole and while depressing the button, apply the brake and shift into neutral to override the brake-shift interlock. 5. Return the access cover and rotate to the closed position (clockwise). Start the vehicle. If it is necessary to use the above procedure to move the gearshift lever, it is possible that a fuse has blown or the vehicle’s brakelamps are not operating properly. Refer to Fuses and relays in the Roadside emergencies chapter.
Driving Do not rock the vehicle for more than a few minutes or damage to the transmission and tires may occur or the engine may overheat. Driving with a 5–speed automatic transmission (if equipped) Your automatic transmission electronically controls the shift feel by using an adaptive learning strategy. This feature is designed to increase durability, and provide consistent shift feel over the life of the vehicle. It is normal for a new transmission to shift firmly.
Driving Always come to a complete stop before shifting into P (Park). Make sure the gearshift lever is securely latched in P (Park). This position locks the transmission and prevents the rear wheels from turning. Always set the parking brake fully and make sure the gearshift is latched in P (Park). Turn the ignition to the LOCK position and remove the key whenever you leave your vehicle. R (Reverse) With the gearshift lever in R (Reverse), the vehicle will move backward.
Driving • driving with a heavy load. • towing a trailer up or down steep hills. • additional engine braking is desired. If towing a trailer, refer to Driving while you tow in the Trailer Towing chapter. To return to D (Overdrive) mode, press the transmission control switch at the end of the gear shift lever. The transmission control indicator light will no longer be illuminated. Each time the vehicle is started, the transmission will automatically return to normal D (Overdrive) mode.
Driving Manual transmission operation (if equipped) Using the clutch When starting a vehicle with a manual transmission: 1. Hold down the brake pedal. 2. Put the gearshift lever in N (Neutral). 3. Depress the clutch pedal. 4. Start the engine and let it idle for a few seconds. • Put the gearshift lever in 1 (First) or R (Reverse). 5. Move foot from brake to accelerator and begin to release the clutch slowly while gradually pressing down on the accelerator.
Driving 2. Engage the parking brake. 3. Shift into 1 (First). 4. Turn the ignition to Off. Do not park your vehicle in Neutral, it may move unexpectedly and injure someone. Use 1 (First) gear and set the parking brake fully.
Driving Shift from: 5 (Overdrive) - 4 4-3 3-2 2-1 Maximum downshift speeds Transfer case position (if equipped) AUTO or HIGH LOW 88 km/h (55 mph) 34 km/h (21 mph) 72 km/h (45 mph) 27 km/h (17 mph) 56 km/h (35 mph) 21 km/h (13 mph) 32 km/h (20 mph) 11 km/h (7 mph) Reverse Ensure that the vehicle is at a complete stop before shifting into R (Reverse). Failure to do so may damage the transmission. Put the gearshift lever into N and wait several seconds before shifting into R.
Driving Power is supplied to all four wheels through a transfer case that allows you to select a four-wheel drive mode best suited for your current driving conditions. Positions of the Control-Trac system The Control-Trac system functions in three modes: • The 4x4 Auto mode provides four-wheel drive with full power delivered to the rear axle, and to the front axle as required for increased traction.
Driving • The 4x4 Low mode supplies four-wheel drive with full power to both axles and includes a lower gear ratio for low-speed. It is only intended for off-road applications that require extra power including deep sand, steep grades and pulling a boat and trailer out of the water. The vehicle should not be operated in 4x4 High and 4x4 Low on dry or merely wet pavement. Doing so will produce excessive noise, increase tire wear and may damage driveline components.
Driving Using the Control Trac system Shifting between 4x4 Auto and 4x4 High When you press the 4x4 High button, the indicator light will illuminate in the instrument cluster. When you press the 4x4 Auto button, the indicator light will turn off. Either shift can be done at a stop or while driving at any speed. 4X4 Auto 4X4 High 4X4 Low Shifting from 4x4 Auto or 4x4 High to 4x4 Low 1. Bring the vehicle to a stop. 2. Depress the brake. 3.
Driving Shifting from 4x4 Low to 4x4 Auto or 4x4 High 1. Bring the vehicle to a stop. 2. Depress the brake. 3. Place the gearshift in N (Neutral) (automatic transmission) or depress the clutch (manual transmission). 4. Press the 4x4 Auto or the 4x4 High button. When 4x4 Auto is engaged NO indicator lights will illuminate. When 4x4 High is engaged the 4x4 High instrument cluster light will illuminate. 4X4 Auto 4X4 High 4X4 Low The 4X4 LOW button will flash if: 1.
Driving Driving at speeds safe for road conditions and the use of safety belts are the best means of minimising the possibility of accident and serious injury. 4WD Systems Your 4WD (when you select the 4x4 mode), uses all four wheels to power itself through the use of a transfer case. How your vehicle differs from other vehicles 4WD vehicles can differ from some other vehicles in a few noticeable ways.
Driving 4WD operation on the road Basic operating principles • Do not use 4x4 high or 4x4 low on dry, hard surfaced roads. This may damage the drivelines and axles. • Drive slower in strong crosswinds which can affect the normal steering characteristics of your vehicle. • Be extremely careful when driving on sealed road made slippery by loose sand, water, gravel, snow or ice.
Driving called for. Avoid abrupt steering, acceleration or braking. Use all available road surface to return the vehicle to a safe direction of travel. • In the event of an emergency stop, avoid skidding the tires and do not attempt any sharp steering wheel movements. • If the vehicle goes from one type of surface to another (i.e., from concrete to gravel) there will be a change in the way the vehicle responds to a maneuver (steering, acceleration or braking). Again, avoid these abrupt inputs.
Driving After driving through mud, clean off residue stuck to rotating driveshafts and tires. Excess mud stuck on tires and rotating driveshafts causes an imbalance that could damage vehicle components. Ford encourages you to help preserve our national forest and other public and private lands by “treading lightly”. Water Before driving through water, determine the depth. Avoid water higher than the bottom of the wheel hubs. Proceed slowly to avoid splashing.
Driving to travel. If you lock the wheels, release the brake pedal and repeat the squeeze technique. If your vehicle has anti-lock brakes, apply the brake steadily. Do not “pump” the brakes. Refer to the Brakes section for additional information on the operation of the anti-lock brake system. Deep snow When driving through deep snow, shift to a low gear and maintain steady pressure on the accelerator.
Driving When climbing a steep slope or hill, start in a lower gear rather than downshifting to a lower gear from a higher gear once the ascent has started. This reduces strain on the engine and the possibility of stalling. If you do stall out, do not try to turn around because you might roll over. It is better to back down to a safe location. Apply just enough power to the wheels to climb the hill. Too much power will cause the tires to slip, spin or lose traction, resulting in loss of vehicle control.
Driving Any modifications to a vehicle that raise the center of gravity can increase the likelyhood of a roll over. Ford recommends that caution be used with any vehicle equipped with a high load or device (such as ladder racks or pickup box cover). Failure to maintain your vehicle properly may reduce vehicle performance and operational capabilities and adversely affect driver and passenger safety.
Driving Extended use of a tire size that is not specified by the manufacturer on a Traction-Lok rear axle could result in a permanent reduction in effectiveness. This loss of effectiveness does not affect normal driving and will not be noticeable to the driver. To reduce the risk of injury, never run the engine with one wheel off the ground, such as when changing a tire.
Driving The weight on the towball must not be greater than 160 kg. The load imposed on the rear tyres of the towing vehicle must not exceed the combined load rating of the two rear tyres. Aftermarket load levelling kits or weight distribution are not suitable for use with the Ford-approved 1600 kg gooseneck.
Driving Vehicle operation The behavior of your vehicle will change while towing a trailer. If your trailer runs off the paved highway surface onto the road shoulder, resist the temptation to quickly turn the steering wheel to bring the trailer back onto the road. Instead, allow the left wheels of the vehicle to also run off onto the shoulder (if safe) then wait for the right conditions to steer the vehicle back onto the road. This should reduce any abrupt swerving reaction.
Driving New vehicle towing weight restrictions Towed To avoid damaging the vehicle, Weight 2500kg restrict the towed weight for the 1600kg first 3,000 km of travel. 1200kg 500kg 1500km 2000km 2500km 3000km Distance Travelled New Vehicle Towed Weight Restrictions Servicing after you tow If you tow a trailer for long distances, your vehicle will require more frequent service intervals. Refer to your Service Guide for more information.
Driving Check and/or replace the rear axle lubricant if: • a leak is suspected or repair required • the axle has been submerged in water Disconnect the wiring to the trailer before backing the trailer into the water. Reconnect the wiring to the trailer after the trailer is removed from the water. ROOF RACK Your vehicle is equipped with a roof rack. The maximum recommended load is 90 kg (200 lbs), evenly distributed. If it is not possible to distribute the load, position it as far rearward as possible.
Roadside emergencies HAZARD FLASHER Use only in an emergency to warn traffic of vehicle breakdown, approaching danger, etc. The hazard flashers can be operated when the ignition is off. • The hazard lights control is located on top of the steering column. • Depress hazard lights control to activate all hazard flashers simultaneously. • Depress control again to turn the flashers off.
Roadside emergencies Use the following procedure to reset the fuel pump shut-off switch. 1. Turn the ignition to the OFF position. 2. Check the fuel system for leaks. 3. If no fuel leak is apparent, reset the fuel pump shut-off switch by pushing in on the reset button. 4. Turn the ignition to the ON position. Pause for a few seconds and return the key to the OFF position. 5. Make a further check for leaks in the fuel system.
Roadside emergencies Standard fuse amperage rating and color COLOR Fuse rating Mini fuses Standard fuses Maxi fuses 2A 3A 4A 5A 7.
Roadside emergencies 6 16 21 26 7 17 22 27 8 18 23 28 9 19 24 29 10 20 25 30 11 1 2 3 4 12 13 14 15 5 The fuses are coded as follows: Fuse/Relay Location 1 2 3 4 5 6 7 8 9 10 Fuse Amp Rating 30A 20A 20A 5A 15A 10A 15A – – 10A 11 — Passenger Compartment Fuse Panel Description Memory seat module Not used (Spare) Radio, Amplifier, Power antenna, DVD Front wiper module Flasher relay (Turn, hazards) Right horn Not used (Spare) Not used (spare) Not used (spare) Heated backlight relay c
Roadside emergencies Fuse/Relay Location 12 13 Fuse Amp Rating 5A 5A 14 15 16 5A 5A 5A 17 15A 18 19 20 10A 10A 5A 21 5A 22 23 10A 15A 24 25 15A 5A 26 7.5A 27 7.5A 28 5A 174 Passenger Compartment Fuse Panel Description Foglamp switch, 4x4 module Overdrive cancel switch, Flex fuel sender PATS module Rear wiper module, Cluster, TPMS Power mirror, Manual climate control, TPMS Delayed acc.
Roadside emergencies Fuse/Relay Location 29 Fuse Amp Rating 10A 30 5A Passenger Compartment Fuse Panel Description Digital transmission range sensor, PWR feed to fuse #28 (Start feed) Remote solenoid, DEATC climate controller Power distribution box The power distribution box is located in the engine compartment. The power distribution box contains high-current fuses that protect your vehicle’s main electrical systems from overloads. Always disconnect the battery before servicing high current fuses.
Roadside emergencies The high-current fuses are coded as follows: Fuse/Relay Location 1 2 3 4 5 6 7 8 9 10 11 12 13 Fuse Amp Rating 60A** 30A** 20A** 30A** 40A** 60A** 20A** — 20A** 30A** 40A** 50A** 40A** 14 15 16 17 18 10A* 15A* 15A* 20A* 20A* 176 Power Distribution Box Description PJB BSM Not used (Spare) Rear defrost ABS (pump) Delayed accessory circuit breaker Power point #2 Not used Power point #1 ABS module (valves) PTEC Ignition relay/Starter relay Trailer tow battery, Trailer tow turn signals
Roadside emergencies Fuse/Relay Location 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 Fuse Amp Rating 20A** 30A** 30A** 20A** 30A** 20A* – 15A* 20A* 20A* 60A** 20A** — — 30A** 30A** 20A** 40A** 15A* 15A* 15A* 15A* 15A* 10A* 10A* 15A* 5A* 20A* — — — Power Distribution Box Description High beam relay Electric brake Front wiper motor Autolamp; Low beam Ignition switch Rear Fog Lamps Not used Fuel pump Trailer tow lamps Horn relay PJB Rear wiper motor Not used N
Roadside emergencies Fuse/Relay Fuse Amp Location Rating 50 — 51 — 52 — 53 — 54 — 55 — 56 — 57 — 58 — 59 — 60 — 61 — 62 30A CB * Mini Fuses ** Maxi Cartridge Power Distribution Box Description Fog lamp relay Police IVD relay A/C clutch relay Trailer tow right turn Trailer tow left turn Blower motor relay Starter relay PTEC relay Ignition relay Driver brake applied PCM diode A/C clutch diode Delayed accessory Fuses CHANGING THE TYRES It is important to observe the following precautions before jacking up th
Roadside emergencies To lessen the risk of personal injury, do not put any part of your body under the vehicle while changing a tyre. Do not start the engine when your vehicle is on the jack. The jack is only meant for changing the tyre. The jack should be used on firm level ground with the vehicle parked away from traffic.
Roadside emergencies Removing the jack 1. Open liftgate and remove the carpeted floor lid and jack cover. 2. Turn jack screw eyelet counterclockwise and remove the jack from the bracket. 3. Remove the lug wrench from the bag and rotate the wrench socket out from the handle. Removing the spare tire Do not use a pneumatic or electrical wrench on the winch drive nut. This will damage the spare tire winch. 1. Insert the jack handle into the rear bumper opening.
Roadside emergencies 2. Turn the handle counterclockwise until tire is lowered to the ground, the tire can be slid rearward and the cable is slightly slack. 3. Remove the retainer from the spare tire. Stowing the spare tire 1. Lay the tire on the ground with the valve stem facing up. 2. Slide the wheel under the vehicle and install the retainer through the wheel center. 3. Turn the jack handle clockwise until the tire is raised to its original position underneath the vehicle.
Roadside emergencies Exercise caution when jacking vehicles fitted with a Limited Slip Differential. Power will be delivered to a rear wheel on the ground even though the opposite wheel is raised. Do not start the engine of a vehicle which is mounted on a jack. Firmly apply the park brake and engage first or reverse (manual transmission) or P (Park) (automatic transmission). Block the front and rear of the wheel diagonally opposite the wheel being changed.
Roadside emergencies Assemble the jack handle extension on the lug nut wrench by sliding the square end through the plastic grommet on the lug nut wrench. To disconnect, depress button and pull apart. Position the jack on the frame under the diamond shaped hole shown in the diagram. Raise the vehicle by turning the jack handle clockwise.
Roadside emergencies • Never use the front or rear differential as a jacking point. Remove the wheel nuts, remove the wheel and replace with the spare wheel. Replace the wheel nuts cone side in and tighten, first by hand and then using the wrench. Tighten in a crosswise pattern. Lower the vehicle to the ground and then check to make sure all wheel nuts are tight.
Roadside emergencies BOOSTER STARTING Jump starting could be dangerous if done incorrectly. Therefore, if the following conditions cannot be met, or if you are uncertain about them, we strongly recommend that you leave the starting to a competent mechanic or towing service. Do not attempt a jump-start if the discharged battery is frozen or if the battery fluid level is low, as the battery may rupture or explode. If instructions are not observed, damage to electronic components may result.
Roadside emergencies Do not let children touch the battery. Batteries contain sulphuric acid which burns skin, eyes and clothing. if the acid touches someone’s skin, eyes or clothing, immediately flush the area with water for at least 15 minutes. If someone swallows the acid, have them drink lots of milk or water first. Follow this by drinking milk of magnesia, a beaten egg, or vegetable oil. Call a doctor immediately.
Roadside emergencies Connect the other end of the same black lead to the jump starting bolt of the vehicle with the discharged battery. Make the final connection of the negative (-) cable to the provided jump starting bolt ONLY. Connecting to any other exposed component may cause an explosion. • Ensure that the cables are clear of fan blades, belts, moving parts of both engines, or any fuel delivery system parts. 4.
Roadside emergencies 4.6L Engine Do not connect the lead to the negative terminal of the discharged battery. Take care that the jumper clamps do not touch each other or any metal on either vehicle, and are clear of the cooling fans and drive belt. Do not lean over the battery when making connections.
Roadside emergencies Engine starting procedure 1. Start the engine in the vehicle with the booster battery and let it run for a few minutes. 2. Start the engine in the vehicle with the discharged battery. 3. Leave the jumper leads connected until the engine reaches idle speed (at least one minute) otherwise damage to the electrical system may occur. 4.
Roadside emergencies TOWING THE VEHICLE If you need to have your vehicle towed, contact a professional towing service or, if you are a member, your roadside assistance center. It is recommended that your vehicle be towed with a wheel lift and dollies or flatbed equipment with all the wheels off the ground. Do not tow with a slingbelt. Ford Motor Company has not approved a slingbelt towing procedure. If the vehicle is towed by other means or incorrectly, vehicle damage may occur.
Maintenance and care PRECAUTIONS WHEN SERVICING YOUR VEHICLE Be especially careful when inspecting or servicing your vehicle. • Do not work on a hot engine. • When the engine is running, make sure that loose clothing, jewellery or long hair does not get caught up in moving parts. • Do not work on a vehicle with the engine running in an enclosed space, unless you are sure you have enough ventilation.
Maintenance and care High voltage Engines with an electronic ignition system can generate very high voltages. Care should be taken when servicing to avoid contact with conductive parts to avoid severe electrical shock. These systems can produce dangerous high tension voltages in the primary and secondary circuit. Please ensure that all work is carried out with the utmost care. Before removing or refitting any parts or electrical connections ensure that the ignition system is switched off.
Maintenance and care Working with the engine off 1. Set the parking brake and ensure the gearshift is securely latched in P (Park). 2. Turn off the engine and remove the key. 3. Block the wheels to prevent the vehicle from moving unexpectedly. Working with the engine on 1. Set the parking brake and ensure the gearshift is securely latched in P (Park). 2. Block the wheels to prevent the vehicle from moving unexpectedly.
Maintenance and care The fluid reservoirs for engine coolant, brake and windscreen washer fluids are translucent to allow rapid visual checks. For easy identification, all the filler caps and the engine oil and automatic transmission fluid dipsticks are marked yellow. Maintenance chart Everyday checks: Check when refuelling: •Engine oil level • Operation of all exterior and interior •Coolant level •Brake fluid level lights including •Windscreen washer instrument warning level lights.
Maintenance and care 2. Go to the front of the vehicle and release the auxiliary latch that is located in the center top of the grill. 3. Lift the hood until the lift cylinders hold it open.
Maintenance and care IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 4.0L SOHC V6 engine 1. 2. 3. 4. 5. 6. 7. 8. 9.
Maintenance and care 4.6L V8 engine 1. 2. 3. 4. 5. 6. 7. 8. 9.
Maintenance and care ENGINE OIL Checking the engine oil Refer to the scheduled maintenance guide for the appropriate intervals for checking the engine oil. 1. Make sure the vehicle is on level ground. 2. Turn the engine off and wait a few minutes for the oil to drain into the oil pan. 3. Set the parking brake and ensure the gearshift is securely latched in P (Park) (automatic transmissions) or 1 (First) (manual transmissions). 4. Open the hood. Protect yourself from engine heat. 5.
Maintenance and care 6. Wipe the indicator clean. Insert the indicator fully, then remove it again. • If the oil level is within the cross hashing area, the oil level is acceptable. DO NOT ADD OIL. • If the oil level is below the MIN level, add enough oil to raise the level within the MIN-MAX range. • Oil levels above the MAX level may cause engine damage. Some oil must be removed from the engine by a qualified service technician. • 4.0L V6 engine • 4.6L V8 engine 7.
Maintenance and care Adding engine oil 1. Check the engine oil. For instructions, refer to Checking the engine oil in this chapter. 2. If the engine oil level is not within the normal range, add only certified engine oil of the recommended viscosity. Remove the engine oil filler cap and use a funnel to pour the engine oil into the opening. 3. Recheck the engine oil level. Make sure the oil level is not above the MAX level on the engine oil level indicator (dipstick). 4.
Maintenance and care Engine oil and filter recommendations for 4.6L V8 engine Your engine has been factory fitted with SAE 5W-20 ILSAC-GF3 engine oil, which meets Ford specification WSS-M2C153–H The recommended oil for service fill in Australia and New Zealand is SAE 5W-30 ILSAC-GF2 engine oil, which meets Ford specification WSS-M2C910–A1. If this oil is not readily available then SAE 10W-30 ILSAC-GF2 engine oil, which meet Ford specification WSS-M2C910–A2 may be used.
Maintenance and care WINDSHIELD WASHER FLUID Check the washer fluid whenever you stop for fuel. The reservoir is highlighted with a symbol. Add fluid to fill the reservoir if the level is low. In very cold weather, do not fill the reservoir completely. Note: Do not put washer fluid in the engine coolant reservoir. Washer fluid placed in the cooling system may harm engine and cooling system components.
Maintenance and care The coolant level should be between the MIN and the MAX markings when the engine is cold. Hot coolant expands and may therefore rise above the MAX mark. Have your dealer check the engine cooling system for leaks if you have to add more than 1.0 liter of engine coolant per month. Adding engine coolant Never remove the coolant reservoir cap when the engine is hot. Allow the engine to cool before removing the cap.
Maintenance and care Vehicles with green coolant: Top up with coolant that meets the Ford specification WSS-M97B44A, which is green in color. Refer to the Service Guide for service intervals. Vehicles with yellow coolant: Top up with coolant that meets the Ford specification WSS-M97B51–A1, which is yellow in color. Refer to the Service Guide for service intervals. Do not allow coolant to come into contact skin or eyes. If this should happen, immediately rinse the affected areas with water.
Maintenance and care Coolant disposal Always dispose of used automotive fluids in a responsible manner. Follow your community’s regulations and standards for recycling and disposing of automotive fluids. Coolant refill capacity To find out how much fluid your vehicle’s cooling system can hold, refer to Refill capacities in the Capacities and specifications chapter. Fill your engine coolant reservoir as outlined in Adding engine coolant in this chapter. Fail-safe cooling (4.
Maintenance and care When fail-safe mode is activated You have limited engine power when in the fail-safe mode, so drive the vehicle with caution. The vehicle will not be able to maintain high speed operation and the engine will run rough. Remember that the engine is capable of completely shutting down automatically to prevent engine damage, therefore: 1. Pull off the road as soon as safely possible and turn off the engine. 2. Arrange for the vehicle to be taken to a service facility. 3.
Maintenance and care • 4.6L V8 engine 1. Start the engine and let it run until it reaches normal operating temperature (the engine coolant temperature gauge indicator will be near the center of the normal area between H and C). 2. While the engine idles, turn the steering wheel left and right several times. 3. Turn the engine off. 4. Check the fluid level in the reservoir. 5. The fluid level should be between the MIN and MAX lines. Do not add fluid if the level is in this range. 6.
Maintenance and care Checking and adding manual transmission fluid 1. Clean the filler plug. 2. Remove the filler plug and inspect the fluid level. 3. Fluid level should be at bottom of the opening. 4. Add enough fluid through the filler opening so that the fluid level is at the bottom of the opening. 5. Install and tighten the fill plug securely. Use only fluid that meets Ford specifications. Refer to Capacities and specifications in this guide.
Maintenance and care CHECKING AND ADDING TRANSFER CASE FLUID 1. Clean the filler plug. 2. Remove the filler plug and inspect the fluid level. 3. Add only enough fluid through the filler opening so that the fluid level is at the bottom of the opening. Use only fluid that meets Ford specifications. Refer to Capacities and specifications in this guide.
Maintenance and care DRIVELINE UNIVERSAL JOINT AND SLIP YOKE Your vehicle may be equipped with universal joints that require lubrication. Refer to the scheduled maintenance guide for maintenance intervals. If the original universal joints are replaced with universal joints equipped with grease fittings, lubrication will also be necessary. BATTERY Your vehicle is equipped with a Motorcraft maintenance-free battery which normally does not require additional water during its life of service.
Maintenance and care Batteries normally produce explosive gases which can cause personal injury. Therefore, do not allow flames, sparks or lighted substances to come near the battery. When working near the battery, always shield your face and protect your eyes. Always provide proper ventilation. When lifting a plastic-cased battery, excessive pressure on the end walls could cause acid to flow through the vent caps, resulting in personal injury and/or damage to the vehicle or battery.
Maintenance and care RN LE TU AD RE When the battery is disconnected or a new battery installed, the automatic transmission must relearn its adaptive strategy. As a result of this, the transmission may shift firmly. This operation is considered normal and will not affect function or durability of the transmission. Over time the adaptive learning process will fully update transmission operation to its optimum shift feel.
Maintenance and care Renewing wiper blades It is recommended that wiper blades are renewed before winter. To replace the wiper blades: 1. Fold back the wiper arm and position the wiper blade at right angles to the wiper arm. 2. To remove, press the retaining clip (A) to disengage the wiper blade, then pull the blade down toward the windshield to remove it from the arm. 3. Install the new wiper blade on the arm and press it into place until a click is heard.
Maintenance and care Regularly inspect the tire treads and remove stones, nails, glass or other objects that may be wedged in the tread grooves. Check for holes or cuts that may permit air leakage from the tire and make necessary repairs. Also examine the tire surface for uneven wear. An uneven tread wear pattern could indicate faulty wheel alignment. Have the wheel alignment on your vehicle checked if you find uneven tire wear. Inspect the tire sidewalls for cuts, bruises and other damage.
Maintenance and care Tire rotation The illustrated sequence should be followed when tire rotation is performed. Tires, replacement requirements Your 4WD vehicle is equipped with tires designed to provide for safe ride and handling capability. Do not use a size and type of tire and wheel other than that originally provided by Ford because it can affect the safety and performance of your vehicle, which could lead to loss of vehicle control or rollover and serious injury.
Maintenance and care Do not use “aftermarket lift kits” or other suspension modifications, whether or not they are used with larger tires and wheels. These “aftermarket lift kits” could adversely affect the vehicle’s handling characteristics, which could lead to loss of vehicle control or rollover and serious injury. FUEL Choosing the right fuel Use only UNLEADED FUEL. Refueling When refueling, always switch off the engine and never allow sparks or open flames near the filler neck.
Maintenance and care Turn the ignition off. Open the fuel door and slowly unscrew the petrol cap anti-clockwise. The fuel system may be under pressure. If the fuel cap is venting vapour or if you hear a hissing sound, wait until it stops before completely removing the cap. Otherwise fuel may spray out and injure you. Fully insert the filler nozzle into the neck of the filler pipe. After refuelling, replace the cap until the ratchet is engaged for at least two clicks and close the fuel door.
Maintenance and care Fuel Filter For fuel filter replacement, see your Ford Dealer. Refer to the Service Guide for the appropriate intervals for changing the fuel filter. Replace the fuel filter with an appropriate Ford fuel filter.
Maintenance and care • Do not turn off the ignition while your vehicle is moving, especially at high speeds. • Have the items listed in your scheduled maintenance guide performed according to the specified schedule. The scheduled maintenance items listed in the service guide are essential to the life and performance of your vehicle and to its emissions system. Do not park, idle, or drive your vehicle in dry grass or other dry ground cover.
Maintenance and care Replacing headlamp bulbs The high beam and low beam bulbs are located in the headlamp assembly. Follow the same steps to replace either bulb: To remove the headlamp bulb: 1. Make sure headlamp switch is in OFF position, then open the hood. 2. At the back of the headlamp, pry up the two retainer pins until they stop to release the headlamp assembly from the vehicle and pull headlamp forward. 3.
Maintenance and care If the bulb is accidentally touched, it should be cleaned with rubbing alcohol before being used. 1. Install the new bulb in lamp assembly by pushing straight in and turning to lock in position. You may need to turn the bulb slightly to align the grooves in the plastic base with the tabs in the lamp assembly. 2. Connect the electrical connector to the bulb. 3.
Maintenance and care Replacing tail/brake/turn/backup lamp bulbs The tail/brake/turn/backup bulbs are located in the tail lamp assembly, one just below the other. Follow the same steps to replace either bulb: 1. Make sure headlamp switch is in OFF position, then open the liftgate to expose the lamp assembly screws. 2. Remove the two screws from the lamp assembly. 3. Pull the lamp assembly towards the rear and side of the vehicle at an angle carefully removing it from the vehicle. 4.
Maintenance and care Replacing license plate lamp bulbs 1. Make sure headlamp switch is in OFF position, then remove two screws and the license plate lamp assembly from the liftgate. 2. Rotate bulb socket counterclockwise and remove from lamp assembly. 3. Carefully pull the bulb from the socket and push in the new bulb. 4. Install the lamp assembly on liftgate with two screws. Replacing high-mount brake lamp bulbs 1.
Maintenance and care USING THE RIGHT BULBS Function Number of bulbs Wattage Turn lamps (front) 2 27W (amber) Headlamps 2 51W/60W Park lamps (front) 2 7W Tail lamps 2 7W Backup/stop (rear)/turn 6 27W (rear) High-mount brake lamps 5 25W Rear license plate lamps 2 Side repeater 2 5W Front sidemarker 2 7W Rear sidemarker 2 7W Driving lamp 2 55W Cargo lamp 1 10W Interior overhead lamp 1 10W Map lamps 2 10W Ashtray lamp 1 5W All replacement bulbs are clear in color except where noted.
Maintenance and care Washing your vehicle Wash your vehicle regularly, particularly in coastal areas, or where salt or chemicals are in the air or used on the roads. Use warm or cold water. Tree sap, insects, bird droppings and road grime or tar may be difficult to remove with water alone. Use a mild soap solution or suitable mild detergent for washing, then rinse with clear water immediately.
Maintenance and care Repairing paint chips Paint damage from road chippings or minor scratches can be dealt with using touch up paint from the Ford accessory range. Observe the application instructions on the products. Wheel cleaning Wheels are coated with a protective finish. Do not use abrasive cleaners, polishing compounds, solvents or wire brushes that might scratch or damage the finish. Avoid washing the wheels using a high pressure washing device.
Maintenance and care 4.6L V8 Engine • Never wash or rinse the engine while it is running; water in the running engine may cause internal damage. Plastic (non-painted) exterior parts Use vinyl cleaners for routine cleaning. Clean with a tar remover, if necessary. Do not clean plastic parts with thinners, solvents or petroleum-based cleaners.
Maintenance and care Cleaning the instrument panel Clean with a damp cloth, then dry with a dry cloth. Avoid cleaner or polish that increases the gloss of the upper portion of the instrument panel. The dull finish in this area helps protect the driver from undesirable windshield reflection. Cleaning leather seats (if equipped) For routine cleaning, wipe the surface with a soft, damp cloth.
Capacities and specifications REFILL CAPACITIES AND LUBRICANT SPECIFICATIONS Fluid Application Capacity Brake fluid and clutch fluid (if equipped) Engine oil (including filter change)* All Fill to line on reservoir 4.0L SOHC V6 engine 4.6L V8 engine (factory fitted)* 4 door 4.7L (5.0 quarts) 5.7 L (6.0 quarts) 85.2L (22.5 gallons) Fill between MIN and MAX lines on reservoir 2.4L (5.1 pints)2 12.0L (12.7 quarts) 3 1.4L (1.
Capacities and specifications Fluid Engine coolant Front axle lubricant 4 Application Capacity 4.0L SOHC V6 engine without auxiliary climate control 4.0L SOHC V6 engine with auxiliary climate control 4.6L V8 engine without auxiliary climate control 4.6L V8 engine with auxiliary climate control All 15.4L (16.3 quarts) Rear axle lubricant 5 Limited Slip Axle Windshield washer fluid All * 17.2L (18.2 quarts) Ford Specification WSS-M97B44–A (green-colored) or WSS-M97B51–A1 (yellow-colored) 17.
Capacities and specifications 1 Ensure the correct automatic transmission fluid is used. MERCONt and MERCONt V are not interchangeable. DO NOT mix MERCONt and MERCONt V. Refer to your scheduled maintenance guide to determine the correct service interval. 2 Service refill capacity is determined by filling the transmission to the bottom of the filler hole with the vehicle on a level surface. 3 Indicates only approximate dry-fill capacity.
Capacities and specifications VEHICLE DIMENSIONS Dimensions (1) Overall length (2) Overall width (3) Maximum height* (4) Wheelbase (5) Track width, front (5) Track width, rear 4-Door 4x4 XLT Model mm (in.) 4 835 (190.4) 1 871 (73.7) 1 807 (71.1) 2 889 (113.7) 1 547 (60.9) 1 554 (61.2) * Height includes roof rack. NOTE: Height is based on P235 tires and may vary depending on tires fitted.
Capacities and specifications 3 5 2 IDENTIFYING YOUR VEHICLE Certification label The Certification Label is located on the driver’s door lock facing. It provides the Gross Vehicle Weight Rating and Gross Axle Weight Ratings. Do not exceed these rating limits as your vehicle may be damaged, or you may lose control and injure somebody. MFD. BY FORD MOTOR CO. IN U.S.A.
Capacities and specifications Vehicle identification number The vehicle identification number is attached to a metal tag and is located in the engine bay. It is also located on the passenger side instrument panel. Engine number The engine number (the last eight numbers of the vehicle identification number) is stamped on the engine block, transmission, frame and transfer case.
Capacities and specifications 235
Capacities and specifications 236
Capacities and specifications 237
Capacities and specifications 238
Index A B ABS (see Brakes) .....................141 Accessory delay ..........................81 Air bag supplemental restraint system ................120, 124 description ..............................124 driver air bag ..........................125 indicator light .............9, 123, 126 operation .................................125 passenger air bag ...................125 service and information labels ................................124, 127 Air conditioning ..........................
Index wiper blades ............................227 Climate control (see Air conditioning or Heating) ............28 Clock ............................................66 Clutch operation while driving ..........151 recommended shift speeds ....152 Compass, electronic set zone adjustment .................17 Console ........................................84 overhead ....................................78 rear ............................................85 Controls power seat ...............................
Index octane rating ...................231–232 running out of fuel .................217 Fuses ..................................171–172 G Gauges .........................................12 battery voltage gauge ...............14 engine coolant temperature gauge .........................................12 engine oil pressure gauge ........14 fuel gauge ..................................15 odometer ...................................13 speedometer .............................12 tachometer ...................
Index charging system ........................10 cruise indicator .........................11 high beam .................................10 low washer fluid .......................10 overdrive off ..............................11 safety belt ...................................9 service engine soon ....................8 speed control ............................74 turn signal indicator .................10 Limited slip axle (see Traction Loc) ....................164 Locks autolock ............................
Index S T Safety belts (see Safety restraints) ....11, 110, 112–115, 117 Safety Canopy ...................124–125 Safety restraints ...........110, 112–115, 117 belt minder .............................118 cleaning the safety belts ........228 for adults .........................112–115 for children .....................128–129 lap belt ....................................116 warning light and chime .............................9, 11, 117 Seat belts (see Safety restraints) .............110 Seats .........
Index W Warning chimes ...........................11 Warning lights (see Lights) .........8 Washer fluid ..............................202 Washing your vehicle ................225 Waxing your vehicle .................225 Windows power .........................................80 244 rear wiper/washer .....................77 Windshield washer fluid and wipers checking and adding fluid .....202 checking and cleaning ............212 liftgate reservoir .....................202 operation .......................
Filling station information Item Required fuel Fuel tank capacity 4.0L V6 Engine oil capacity (includes filter change) Information Unleaded fuel only - 91 RON 85.2L (22.5 gallons) 4.7L (5.0 quarts). Use Ford R1-300 5L Motor Oil, Ford specification WSS-M2C153-G. 5.7L (6.0 quarts). Use SAE 5W-20 Motor Oil, Ford specification WSS-M2C153–H Refer to the Certification Label on inside of driver’s door. Pull handle under the instrument panel. 15.4L (16.3 quarts) 4.
Filling station information MERCONt V. Refer to your scheduled maintenance guide to determine the correct service interval. 3 Indicates only approximate dry-fill capacity. The amount of transmission fluid and fluid level should be checked by a qualified technician .
