FORD C-MAX Quick Reference Guide
About This Quick Reference Guide We have created this guide to help you get to know certain features of your vehicle. It only contains basic instructions to get you started and is not a substitute for the Owner's Manual. You must read the full instructions in the Owner's Manual along with all the warnings. The more that you know about your vehicle, the greater the safety and pleasure you will get from driving it. Thank you for choosing Ford.
INSTRUMENT PANEL OVERVIEW 1 C-MAX (CEU) Vehicles Built From: 16-03-2015 Vehicles Built Up To: 19-07-2015, CG3643en enGBR, Edition date: 02/2015, First Printing
A Air vents. B Direction indicator lever. C Information display control. D Instrument cluster. E Audio control. F Wiper lever. G Information and entertainment display. H Audio unit. I Hazard flasher switch. J Climate controls. K Keyless start button. L Horn. M Steering wheel adjustment. N Cruise control switches. O Lighting control. Unlocking the Doors LOCKING AND UNLOCKING Press the button to unlock all doors. The direction indicators will flash.
Type One Double Locking Double locking is a theft protection feature that prevents someone from opening the doors from the inside. You can only double lock the doors if they are all closed. Press the button twice within three seconds. Locking and Unlocking the Doors with the Key Locking with the Key Turn the top of the key toward the front of your vehicle. Double Locking with the Key Turn the key to the lock position twice within three seconds. A Volume up. B Seek up or next. C Volume down.
Intermittent Wipe Press and hold the seek button to: • Tune the radio to the next station up or down the frequency band. • Seek through a track. INFORMATION DISPLAY CONTROL A Short-wipe interval. B Intermittent wipe. C Long-wipe interval. Push the wiper lever up to switch the wipers on, and then use the rotary control to adjust the intermittent wipe interval. WINDSHIELD WIPERS A Single wipe. B Intermittent wipe. C Normal wipe. D High-speed wipe. AUTOWIPERS A Highest sensitivity. B On.
Rear Window Washer Use the rotary control to adjust the sensitivity of the rain sensor: • Rotate the control down to low sensitivity, and the wipers turn on when the rain sensor detects a large amount of moisture on the windshield. • When you move the wiper lever up to the first position and the autowiper system is on, the autowiper sensitivity setting adjusts the wiper speed according to the moisture on the windshield only. • When you lower the sensitivity, the wipers remain in their ready position only.
Vehicles With Keyless Entry REAR SEATS To close all the windows, press and hold the driver’s door handle for at least three seconds. Second row seats - C-MAX 1. Remove the luggage cover. HEATED WINDOWS AND MIRRORS Heated Rear Window Press the button to clear the window of thin ice and fog. It will switch off automatically after a short period of time. Make sure the engine is running before operating the heated windows.
Note: As the seats slide rearward, they also move slightly inboard. 4. Pull the lever on the outer front edge of the outboard seats and push the seats rearward. 2. Pull the strap and lift the right-hand seat cushion. To return the seats to the forward position, pull the lever and slide the seats forward. To return the center seat to its original position, pull the lever on the underside of the seat. Fold the center seat forward and push it back down fully until it engages. Install the luggage cover.
Press the push button ignition switch once without your foot on the brake or clutch pedal. It is on the instrument panel near the steering wheel. All electrical circuits and accessories are operational and the warning lamps and indicators illuminate. Press the push button ignition switch again without your foot on the brake or clutch pedal to switch the ignition off. Starting Your Vehicle Vehicles with Manual Transmission 1. Fully depress the clutch pedal. 2. Briefly press the push button ignition switch.
AUTO-START-STOP To Re-Start the Engine Switching the System On and Off Release the brake pedal or press the accelerator pedal. HILL START ASSIST The system makes it easier to pull away when your vehicle is on a slope without the need to use the parking brake. When you switch the ignition on, the system automatically turns on. To switch the system off, press the switch and the word OFF illuminates. Press again to switch the system back on. The system only switches off for the current ignition cycle.
When driving at a speed less than 22 mph (35 km/h) the system automatically scans both sides of your vehicle for an available parking space. The system displays a message and a corresponding graphic to indicate it is searching for a parking space. Use the direction indicator to select searching either to the left-hand side or right-hand side of your vehicle.
The system uses three types of guides to help you see what is behind your vehicle: • Active guidelines: Show the intended path of your vehicle when reversing. • Fixed guidelines: Show the actual path your vehicle is moving in while reversing in a straight line. This can be helpful when backing into a parking space or aligning your vehicle with another object behind you. • Centerline: Helps align the center of your vehicle with an object (for example, a trailer).
Canceling the Set Speed Cross Traffic Alert also sounds a series of tones and a message appears in the information display indicating a vehicle is coming from the right or left. Cross Traffic Alert works with the reverse sensing system that sounds its own series of tones. Press and release CAN to place the system in standby mode. The system will not erase the set speed. Resuming the Set Speed Press and release RES.
As a driver assistance feature, your vehicle has a tire pressure monitoring system. A warning lamp will illuminate when one or more of the tires are significantly under-inflated. If the low tire pressure warning lamp illuminates, you should stop your vehicle as soon as it is safe to do so, check the tires and inflate them to the correct pressure. CHANGING THE WIPER BLADES Setting the Front Wipers in the Service Position 1. Make sure that the outside of the windshield is free from snow and ice. 2.
Tire Pressure Monitoring System Reset Procedure Carrying Out the System Reset Procedure You must carry out the system reset procedure after each tire replacement or adjustment of the tire pressures. 1. Check the tire pressures and inflate all the tires to the correct pressure. 2. Use the information display controls on the steering wheel or instrument panel. To reset the tire pressure monitoring system, scroll to: Message Description and Action Settings Press the OK button.
CG3643en
