FORD B-MAX Owner's Manual
The information contained in this publication was correct at the time of going to print. In the interest of continuous development, we reserve the right to change specifications, design or equipment at any time without notice or obligation. No part of this publication may be reproduced, transmitted, stored in a retrieval system or translated into any language in any form by any means without our written permission. Errors and omissions excepted. © Ford Motor Company 2014 All rights reserved.
Table of Contents Clearing All MyKeys........................................31 Checking MyKey System Status................31 Using MyKey With Remote Start Systems.........................................................32 MyKey Troubleshooting...............................32 Introduction About This Manual...........................................5 Symbols Glossary.............................................5 Replacement Parts Recommendation.........................................
Table of Contents Interior Lamps..................................................51 Auxiliary Power Points Windows and Mirrors Auxiliary Power Points..................................87 Cigar Lighter.....................................................87 Power Windows..............................................52 Global Opening and Closing......................53 Exterior Mirrors................................................54 Interior Mirror...................................................
Table of Contents Automatic Transmission...........................103 Hill Start Assist.............................................106 Towing the Vehicle on Four Wheels Automatic Transmission........................127 Brakes Driving Hints General Information....................................108 Hints on Driving With Anti-Lock Brakes...........................................................108 Parking Brake.................................................108 Breaking-In............................
Table of Contents Brake and Clutch Fluid Check.................150 Washer Fluid Check.....................................150 Changing the 12V Battery..........................150 Checking the Wiper Blades........................151 Changing the Wiper Blades.......................151 Adjusting the Headlamps..........................152 Removing a Headlamp...............................152 Changing a Bulb............................................153 Bulb Specification Chart...........................
Introduction ABOUT THIS MANUAL Thank you for choosing Ford. We recommend that you take some time to get to know your vehicle by reading this manual. The more that you know about it, the greater the safety and pleasure you will get from driving it. WARNING Driving while distracted can result in loss of vehicle control, crash and injury. We strongly recommend that you use extreme caution when using any device that may take your focus off the road.
Introduction Brake system Front airbag Cabin air filter Front fog lamps Check fuel cap Fuel pump reset Child safety door lock or unlock Fuse compartment Child seat lower anchor Hazard warning flashers Child seat tether anchor Heated rear window Cruise control Heated windshield Do not open when hot Interior luggage compartment release Engine air filter Jack Engine coolant Keep out of reach of children Lighting control Engine coolant temperature Low tire pressure warning Engine oil Main
Introduction Scheduled Maintenance and Mechanical Repairs Parking aid One of the best ways for you to make sure that your vehicle provides years of service is to have it maintained in line with our recommendations using parts that conform to the specifications detailed in this Owner’s Manual. Genuine Ford and Motorcraft parts meet or exceed these specifications.
Introduction appropriately used, particularly in emergency situations. Safety must be paramount when using mobile communications equipment to avoid negating these benefits. Mobile communication equipment includes, but is not limited to, cellular phones, pagers, portable email devices, text messaging devices and portable two-way radios. WARNING Driving while distracted can result in loss of vehicle control, crash and injury.
At a Glance Front Exterior Overview A See Locking and Unlocking (page 34). See Keyless Entry (page 37). B See Active City Stop (page 118). C See Changing the Wiper Blades (page 151). D See Maintenance (page 143). E See Towing Points (page 126). F See Changing a Bulb (page 153). G Tire pressures. See Technical Specifications (page 178). H See Changing a Road Wheel (page 173).
At a Glance Vehicle Interior Overview A See Transmission (page 103). B See Locking and Unlocking (page 34). C See Power Windows (page 52). See Exterior Mirrors (page 54). D See Head Restraints (page 82). E See Fastening the Safety Belts (page 21). F See Rear Seats (page 85). G See Manual Seats (page 84). H See Parking Brake (page 108). I See Opening and Closing the Hood (page 143).
At a Glance Instrument Panel Overview Left-Hand Drive 11 B-MAX (CB2) Vehicles Built From: 10-03-2014 Vehicles Built Up To: 03-05-2015, CG3573en enGBR, Edition date: 02/2014, Third Printing
At a Glance Right-Hand Drive A Air vents. See Air Vents (page 74). B Direction indicators. See Direction Indicators (page 51). High beam. See Lighting Control (page 47). C Instrument cluster. See Gauges (page 57). See Warning Lamps and Indicators (page 57). D Start button. See Starting and Stopping the Engine (page 89). E Wiper lever. See Wipers and Washers (page 44). F Information and entertainment display. See Information Displays (page 62). G Audio unit. See Audio System (page 184).
At a Glance K Parking aid switch. See Parking Aids (page 111). L Start-stop switch. See Auto-Start-Stop (page 95). M Card holder or airbag warning lamp. See Passenger Airbag (page 24). N Ignition switch. See Ignition Switch (page 89). O Cruise control switches. See Using Cruise Control (page 116). P Horn. Q Driver knee airbag. See Driver Knee Airbag (page 25). R Steering wheel adjustment. See Adjusting the Steering Wheel (page 42). S Audio control. See Audio System (page 184).
At a Glance Rear Exterior Overview A See Changing a Bulb (page 153). B See Changing the Wiper Blades (page 151). C See Changing a Bulb (page 153). D See First Aid Kit (page 131). See Warning Triangle (page 131). See Temporary Mobility Kit (page 165). Spare wheel, jack, and wheel brace. See Changing a Road Wheel (page 173). Towing eye. See Towing Points (page 126). E See Towing Points (page 126). F Tire pressures. See Technical Specifications (page 178). G See Changing a Road Wheel (page 173).
Child Safety INSTALLING CHILD SEATS WARNINGS If your vehicle has been involved in a crash, have the child seats checked by an authorized dealer. Note: Mandatory use of child seats varies from country to country. Only child seats certified to ECE-R44.03 (or later) have been tested and approved for use in your vehicle. A choice of these are available from an authorized dealer.
Child Safety Child Safety Seat Booster Seat (Group 2) Secure children that weigh between 29 and 40 pounds (13 and 18 kilograms) in a child safety seat (Group 1) on the rear seat. Secure children that weigh more than 33 pounds (15 kilograms) but are less than 59 inches (150 centimeters) tall in a booster seat or a booster cushion. Booster Seats We recommend that you use a booster seat that combines a cushion with a backrest instead of a booster cushion only.
Child Safety ISOFIX Anchor Points Attaching a Child Seat with Top Tethers WARNING WARNINGS Do not attach a tether strap to anything other than the correct tether anchor point. Use an anti-rotation device when using the ISOFIX system. We recommend the use of a top tether or support leg. Make sure that the top tether strap is not slack or twisted and is properly located on the anchor point.
Child Safety CHILD SEAT POSITIONING WARNINGS The child seat must rest tightly against the vehicle seat. It may be necessary to lift or remove the head restraint. See Head Restraints (page 82). WARNINGS See an authorized dealer for the latest details relating to our recommended child seats. Note: When using a child seat on a front seat, always adjust the front passenger's seat to its fully rearward position.
Child Safety ISOFIX Child Seats Mass group categories 0+ 1 Rear facing Forward facing Up to 29 lbs (13 kg) 20 - 40 lbs (9 - 18 kg) Seating positions Front seat Size class Not ISOFIX equipped Seat type Rear outboard seat ISOFIX Rear center seat Size class C, D, E Seat type IL 1 Size class 2 1 A, B, B1 3 IL, IUF Not ISOFIX equipped Seat type IL Suitable for particular ISOFIX child seat systems of the semi-universal category.
Child Safety CHILD SAFETY LOCKS WARNING You cannot open the doors from inside if you have put the child safety locks on. Left-Hand Side Turn counterclockwise to lock and clockwise to unlock. Right-Hand Side Turn clockwise to lock and counterclockwise to unlock.
Safety Belts FASTENING THE SAFETY BELTS WARNINGS Insert the tongue into the buckle until you hear a distinct click. You have not fastened the safety belt correctly if you do not hear a click. Make sure that your safety belt is securely stored away and is not outside your vehicle when closing the door. Pull the belt out steadily. It may lock if you pull it sharply or if your vehicle is on a slope. Press the red button on the buckle to release the belt. Let it retract completely and smoothly.
Safety Belts Using Safety Belts During Pregnancy It will also illuminate and sound if a front safety belt is unfastened when your vehicle is moving. If you do not fasten your safety belt the warning switches off automatically after approximately five minutes. Turning the Safety Belt Minder Off Contact an authorized dealer. WARNING Position the safety belt correctly for your safety and that of your unborn child. Do not use only the lap strap or the shoulder strap.
Supplementary Restraints System Note: You will hear a loud bang and see a cloud of harmless powdery residue if an airbag deploys. This is normal. PRINCIPLE OF OPERATION WARNINGS Extreme Hazard! Never use a rearward facing child restraint on a seat protected by an active airbag in front of it. Death or serious injury to the child can occur. Note: Only wipe airbag covers with a damp cloth. DRIVER AIRBAG Do not modify the front of your vehicle in any way.
Supplementary Restraints System PASSENGER AIRBAG The airbag will deploy during a significant frontal crash or crashes that are up to 30 degrees from the left or the right. The airbag will inflate within a few thousandths of a second and deflate on contact with the occupant cushioning forward body movement. During minor frontal crashes, sideways crashes, rear crashes or overturns, the airbag will not deploy. A Switch off B Switch on Turn the switch to position A.
Supplementary Restraints System For item location: See At a Glance (page 9). SIDE AIRBAGS WARNING Note: The airbag has a lower deployment threshold than the front airbags. During a minor collision, it is possible that only the knee airbag will deploy. Use seat covers designed for seats with side airbags. Have these fitted by an authorized dealer. SIDE CURTAIN AIRBAGS The airbags are located inside the seatback of the front seats. There is a label attached to the side of the seatback to indicate this.
Keys and Remote Controls GENERAL INFORMATION ON RADIO FREQUENCIES REMOTE CONTROL You can program a maximum of eight remote controls to your vehicle. This includes any that were supplied with your vehicle. The remote controls must remain inside your vehicle during the programming procedure. Fasten the front safety belts and close all doors to make sure that conflicting chimes do not sound during programming.
Keys and Remote Controls Press and hold the unlock and lock buttons on the remote control simultaneously for at least four seconds with the ignition off. The direction indicators will flash twice to confirm the change. To return to the original unlocking function, repeat the process. Changing the Remote Control Battery Make sure that you dispose of old batteries in an environmentally friendly way. Seek advice from your local authority regarding recycling. 2.
Keys and Remote Controls 4. Carefully remove the battery with the screwdriver. 5. Install a new battery (3V CR 2032) with the + facing downwards. 6. Assemble the two halves of the remote control. 7. Install the key blade. Remote Control Without a Folding Key Blade 4. Twist the screwdriver in the position shown to separate the two halves of the remote control. 1. Press and hold the buttons on the edges to release the cover. Carefully remove the cover. 2. Remove the key blade.
Keys and Remote Controls REPLACING A LOST KEY OR REMOTE CONTROL Replacement or additional keys or remote controls can be purchased from an authorized dealer. Your dealer can program the remote controls for your vehicle or you may be able to program them yourself. See Remote Control (page 26). To re-program the passive anti-theft system see an authorized dealer.
MyKey™ Optional Settings PRINCIPLE OF OPERATION You can configure MyKey settings when you first create a MyKey. You can also change the settings afterward with an admin key. The system allows you to program keys with restricted driving modes to promote good driving habits. You can use all but one of the keys programmed to your vehicle with these restricted modes. The following settings can be configured using an admin key: • Various vehicle speed limits can be set.
MyKey™ 4. Select Create MyKey and press OK. 5. When prompted, press and hold OK until you see a message informing you to label this key as a MyKey. The key will be restricted the next time you use it. Note: Make sure you label the MyKey so you can distinguish it from the admin keys. PROGRAMMING A MYKEY Vehicles with Keyless Starting 3. Optional Settings 1. 2. 1. Switch the ignition on using an admin key. 2. Access the main menu using the information display.
MyKey™ MyKey Distance Number of Admin Keys Tracks the distance when drivers use a MyKey. The only way to delete the accumulated distance is by using an admin key to clear all MyKeys. If the distance does not accumulate as expected, then the intended user is not using the MyKey, or an admin key user recently cleared and then recreated a MyKey. Indicates how many admin keys are programmed to your vehicle.
MyKey™ Vehicles With Push Button Start Condition Potential Causes I cannot create a MyKey. The key is not in the backup position. See Creating a MyKey (page 30). There are no MyKey driving modes. An admin key is present when you switch the ignition on. There are no MyKeys programmed to your vehicle. See Creating a MyKey (page 30).
Locks Press the button again within three seconds to confirm that all the doors are closed. The doors will lock again, and the turn signals will illuminate if all the doors and the luggage compartment are closed. LOCKING AND UNLOCKING Power Door Locks • Press the button once. The doors will lock. Press the button again. The doors will unlock. For item location: See At a Glance (page 9).
Locks Locking With the Key Turn the top of the key toward the front of your vehicle. Double Locking With the Key Turn the key to the lock position twice within three seconds. Unlocking With the Key Note: If the child safety locks are on and you pull the interior handle, you will only turn off the emergency locking, not the child safety lock. You can only open the doors using the external door handle. Push to lock.
Locks Opening and Closing the Liftgate MANUAL LIFTGATE To Open the Liftgate WARNINGS It is extremely dangerous to ride in a cargo area, inside or outside of your vehicle. In a crash, people riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts. Make sure everyone in your vehicle is in a seat and properly using a safety belt.
Locks Passive Key KEYLESS ENTRY Your vehicle can be locked and unlocked with the passive key. You can use the passive key as a remote control. See Locking and Unlocking (page 34). General Information WARNING The system may not function if the key is close to metal objects or electronic devices such as cell phones. Locking Your Vehicle The system will not function if: • Your vehicle battery has no charge. • The passive key frequencies are jammed. • The passive key battery is flat.
Locks Liftgate Disabled Keys Note: The liftgate cannot be closed and will pop back up if the passive key is located inside the luggage compartment with the doors locked. Any keys left inside your vehicle interior when it is locked will be disabled. You cannot use a disabled key to switch the ignition on or start the engine. Note: If a second valid passive key is located within the liftgate detection range, the liftgate can be closed. You must enable all passive keys again in order to use them.
Security • • • PASSIVE ANTI-THEFT SYSTEM Principle of Operation The system prevents someone from starting the engine with an incorrectly coded key. Perimeter alarm. Perimeter alarm with interior sensors. Category one alarm with interior sensors and battery back-up sounder. Perimeter Alarm The perimeter alarm is a deterrent against unauthorized access to your vehicle through the doors and the hood. It also protects the audio unit.
Security Triggering the Alarm Ask on Exit (If Equipped) Once armed, the alarm is triggered in any of the following ways: You can set the information display to ask you each time which level of guard you wish to set. • • • • • If someone opens a door, the liftgate or the hood without a valid key or remote control. If someone removes the audio or navigation system. If you switch the ignition on without a valid key. If the interior sensors detect movement within your vehicle.
Security Category One Alarm Disarm and silence the alarm by unlocking the doors with the key and switching the ignition on with a correctly coded key within 12 seconds or unlocking the doors with the remote control. Vehicles with Keyless Entry Note: A valid passive key must be located within the detection range of that door for keyless entry. See Keyless Entry (page 37).
Steering Wheel ADJUSTING THE STEERING WHEEL WARNING Do not adjust the steering wheel when your vehicle is moving. Note: Make sure that you are sitting in the correct position. See Sitting in the Correct Position (page 82). 3. Lock the steering column. AUDIO CONTROL Select the required source on the audio unit. You can operate the following functions with the control: 1. Unlock the steering column. 2. Adjust the steering wheel to the desired position.
Steering Wheel C Volume down D Seek down, previous or accept call CRUISE CONTROL Seek, Next or Previous Press the seek button to: • tune the radio to the next or previous stored preset • play the next or the previous track. Press and hold the seek button to: • tune the radio to the next station up or down the frequency band • seek through a track. See Cruise Control (page 116). VOICE CONTROL Press the button to select or deselect voice control. See SYNC™ (page 224).
Wipers and Washers Intermittent Wipe WINDSHIELD WIPERS Note: Fully defrost the windshield before switching on the windshield wipers. Note: Make sure the windshield wipers are switched off before entering a car wash. Note: Install new wiper blades as soon as they begin to leave bands of water and smears on the windshield. Note: Do not operate the wipers on a dry windshield. This may scratch the glass, damage the wiper blades or cause the wiper motor to burn out.
Wipers and Washers In these conditions, you can do the following to help keep your windshield clear: • Lower the sensitivity of the autowipers. • Change the wiper speed to normal or high speed wipe as necessary. • Switch the autowipers off. Keep the outside of the windshield clean. Sensor performance will be affected if the area around the interior mirror is dirty. The rain sensor is very sensitive and the wipers may operate if dirt, mist or flies hit the windshield.
Wipers and Washers Reverse Gear Wipe The rear wiper will turn on automatically when selecting reverse gear if: • the rear wiper is not already switched on • the wiper lever is in position A, B, C or D • the front wiper is operating (when set to position B). Rear Window Washer Note: Do not operate the washers when the washer reservoir is empty. This may cause the washer pump to overheat. Pull the lever toward you to operate the washers. They will operate for a maximum of 10 seconds.
Lighting GENERAL INFORMATION LIGHTING CONTROL Condensation in Lamp Assemblies Lighting Control Positions Exterior lamps have vents to accommodate normal changes in air pressure. Condensation can be a natural by-product of this design. When moist air enters the lamp assembly through the vents, there is a possibility that condensation can occur when the temperature is cold. When normal condensation occurs, a fine mist can form on the interior of the lens.
Lighting Push the lever forward to switch the high beams off. Note: If you have autolamps and autowipers switched on the low beam headlamps will turn on automatically when the windshield wipers operate continuously. Headlamp Flasher Pull the lever toward you slightly and release it to flash the headlamps. Note: You may have to manually switch the headlamps on in severe weather conditions.
Lighting HEADLAMP EXIT DELAY FRONT FOG LAMPS After you switch the ignition off, you can switch the headlamps on by pulling the direction indicator lever toward you. You will hear a short tone. The headlamps will switch off automatically after three minutes with any door open or 30 seconds after the last door has been closed. You can cancel this feature by pulling the direction indicator toward you again or switching the ignition on.
Lighting Note: Only use the rear fog lamps when visibility is less than 164 feet (50 meters). Note: Do not use the rear fog lamps when it is raining or snowing. Note: If you switch autolamps on, you can only switch the fog lamps on once autolamps has turned the headlamps on. HEADLAMP LEVELING Note: Vehicles with Xenon headlamps have automatic headlamp leveling. 1. Press to release the pop out button. 2. Rotate the button to the required setting. 3. Push the button to the closed position.
Lighting If you set the switch to position B, the courtesy lamp will illuminate when you unlock or open a door or the liftgate. If you leave a door open with the ignition switched off, the courtesy lamp will go off automatically after some time to prevent your vehicle battery from losing charge. To switch it back on, switch the ignition on for a short time. DIRECTION INDICATORS The courtesy lamp will also illuminate when you switch the ignition off.
Windows and Mirrors Window Lock POWER WINDOWS WARNINGS Do not leave children unattended in your vehicle and do not let them play with the power windows. They may seriously injure themselves. When closing the power windows, you should verify they are free of obstructions and make sure that children and pets are not in the proximity of the window openings. Press the control to lock or unlock the rear window controls. It lights when the rear window controls lock.
Windows and Mirrors 2. Close the window a third time to the point of resistance. You disabled the bounce-back feature and you can now close the window manually. The window travels past the point of resistance and you can close it fully. Accessory Delay (If Equipped) Contact an authorized dealer as soon as possible if the window does not close after the third attempt.
Windows and Mirrors Press the lock or unlock button to stop the opening function. WARNING Take care when using global closing. In an emergency, touch a door handle lock sensor to stop. Global Closing (If Equipped) Vehicles Without Keyless Entry Note: Global closing can be switched on using the driver’s door handle. Global opening and closing can also be switched on using the buttons on the passive key. WARNING Take care when using global closing.
Windows and Mirrors Press the arrows to adjust the mirror. Electric Folding Mirrors Automatic Folding and Unfolding Note: If the mirrors have been folded using the manual fold button they can only be unfolded using the manual fold button. Press the downward arrow to fold or unfold the mirrors. If you press the switch again while the mirrors are moving, they will stop and reverse the direction of movement.
Windows and Mirrors You can adjust the interior mirror to your preference. Some mirrors also have a second pivot point. This lets you move the mirror head up or down and from side to side. Pull the tab below the mirror toward you to reduce glare at night. Auto-Dimming Mirror (If Equipped) Note: Do not block the sensors on the front and back of the mirror. Mirror performance may be affected. A rear center passenger or raised rear center head restraint may also block light from reaching the sensor.
Instrument Cluster GAUGES A Tachometer B Information display C Speedometer D Fuel gauge E Tripmeter reset button Fuel Gauge WARNING LAMPS AND INDICATORS Switch the ignition on. The fuel gauge will indicate approximately how much fuel is left in the fuel tank. The fuel gauge may vary slightly when your vehicle is moving or on a gradient. The arrow adjacent to the fuel pump symbol indicates on which side of your vehicle the fuel filler door is located.
Instrument Cluster • • • Oil pressure. Power steering. Stability control. If it illuminates when you are driving, this indicates a malfunction. Stop your vehicle as soon as it is safe to do so and switch the engine off. Check the coolant level. See Engine Coolant Check (page 149). When a warning lamp or indicator does not illuminate once you have switched the ignition on, it indicates a malfunction. Have the system checked by an authorized dealer.
Instrument Cluster Exterior Lamps On Indicator WARNING Have this checked immediately. It will illuminate when you switch the headlamp low beam or the side and tail lamps on. If both lamps illuminate together, stop your vehicle as soon as it is safe to do so (continued use may cause reduced power and cause the engine to stop). Switch the ignition off and attempt to restart the engine. If the engine restarts have the system checked by an authorized dealer immediately.
Instrument Cluster Oil Pressure Warning Lamp Stability Control Indicator While driving, it flashes when the system is operating. After you switch the ignition on, if it does not illuminate or illuminates continuously while driving, this indicates a malfunction. During a malfunction, the system switches off. Have the system checked by an authorized dealer as soon as possible. WARNING Do not resume your journey if it illuminates despite the level being correct.
Instrument Cluster Safety Belt Minder WARNINGS The safety belt minder remains in stand-by mode when the front safety belts have been fastened. It will sound if either safety belt is unfastened. Do not sit on top of a fastened safety belt to prevent the safety belt minder from coming on. The occupant protection system will only provide optimum protection when you use the safety belt properly. Sounds when your vehicle speed exceeds the pre-determined limit and the front safety belts are unfastened.
Information Displays Information Display Controls GENERAL INFORMATION WARNING Driving while distracted can result in loss of vehicle control, crash and injury. We strongly recommend that you use extreme caution when using any device that may take your focus off the road. Your primary responsibility is the safe operation of your vehicle. We recommend against the use of any hand-held device while driving and encourage the use of voice-operated systems when possible.
Information Displays SYNC-Phone Dial a number Redial Phonebook Call history Speed Dial Text messaging BT Devices Phone settings Menu Ford EcoMode SYNC-Settings Bluetooth on Set defaults Master reset Install on SYNC System info Voice settings SYNC-Apps Navigation Route options Map display Assistance options Personal data Reset all settings Audio settings Adaptive volume Sound NAV audio mixing 63 B-MAX (CB2) Vehicles Built From: 10-03-2014 Vehicles Built Up To: 03-05-2015, CG3573en enGBR, Edition d
Information Displays Menu DSP settings DSP equalizer Traffic News Alt.
Information Displays Menu Active City Stop Speed limit Speed warning Volume limit Information Clear all MyKeys MyKey active Information System Check TRIP COMPUTER All active warnings will display first if applicable. The system check menu may appear different based upon equipment options and current vehicle status. Press the up or down arrow button to scroll through the list. CLOCK Type 1 Press the button to scroll through the displays.
Information Displays Distance to Empty PERSONALIZED SETTINGS Indicates the approximate distance your vehicle will travel on the fuel remaining in the tank. Changes in driving pattern may cause the value to vary. Measure Units To swap between imperial and metric units, scroll to this display and press the OK button. Swapping between imperial and metric units will affect the following displays: • Distance to empty. • Average fuel consumption. • Instantaneous fuel consumption. • Average speed.
Information Displays Certain messages need to be confirmed before you can access the menus. Some messages will be supplemented by a system specific symbol with a message indicator. The message indicator illuminates to supplement some messages. It will be red or amber depending on the severity of the message and will remain on until the cause of the message has been rectified.
Information Displays Message Boot open Bonnet open Message indicator Action red Vehicle is moving. Stop your vehicle as soon as safely possible and close. red Vehicle is moving. Stop your vehicle as soon as safely possible and close. See Opening and Closing the Hood (page 143). Driver door open amber Vehicle not moving. Close. Driver's rear door open amber Vehicle not moving. Close. Passenger door open amber Vehicle not moving. Close. Passenger rear door open amber Vehicle not moving.
Information Displays Keyless System Message Message indicator Action Key not detected amber See Keyless Entry (page 37). Key outside car amber See Keyless Entry (page 37). Key Battery low Replace battery amber See Remote Control (page 26). Turn ignition off Use POWER button amber See Keyless Starting (page 89). To start press brake - See Keyless Starting (page 89). To start press clutch - See Keyless Starting (page 89). Close boot or use spare key - See Keyless Entry (page 37).
Information Displays Message indicator Action Engine malfunction Service now amber Have your vehicle checked by an authorized dealer as soon as possible. Auto wiper/lights malfunction Next service amber Have your vehicle checked by an authorized dealer as soon as possible. - Have your vehicle checked by an authorized dealer as soon as possible.
Information Displays Message indicator Action Buckle up to unmute audio - Displays when a MyKey is in use and BeltMinder is activated. MyKey Park aid cannot be deactivated - Displays when a MyKey is in use and park aid is activated. MyKey ESC cannot be deactivated - Displays when programming a MyKey. Message Steering Message indicator Action Steering malfunction Service now red Have your vehicle checked by an authorized dealer as soon as possible.
Information Displays Transmission Message indicator Action red Have your vehicle checked by an authorized dealer as soon as possible. red The transmission is overheating and needs to cool. Stop your vehicle as soon as it is safe to do so. Move the transmission selector lever to position N or P and apply the parking brake. Switch off the ignition until the transmission has cooled and the message disappears from the display. Vehicle not in Park Select P - See Automatic Transmission (page 103).
Information Displays Tire Pressure Monitoring System Message Message indicator Action Check Tire pressures amber The pressure in one or more tires has dropped. Check as soon as possible. Tire pressure sys malfunction service required amber Have your vehicle checked by an authorized dealer as soon as possible.
Climate Control Air Conditioning PRINCIPLE OF OPERATION The system directs air through the evaporator for cooling. The evaporator extracts humidity from the air to help keep the windows free of mist. The system directs the resulting condensation to the outside of your vehicle, which may cause a small pool to form under your vehicle. This is normal.
Climate Control Side Air Vent MANUAL CLIMATE CONTROL A Fan speed control: Controls the volume of air circulated in your vehicle. Adjust to select the desired fan speed or switch off. If you switch the fan off, the windshield may fog up. B On and off: Press the button to turn the system on and off. When the system is off, outside air is prevented from entering your vehicle.
Climate Control C Recirculated air: Press the button to switch between outside air and recirculated air. When you select recirculated air, the button illuminates and the air currently in the passenger compartment recirculates. This can reduce the time needed to cool the interior and reduce unwanted odors from entering your vehicle. D Air distribution control: Adjust to select the desired air distribution. E Heated windshield: Press the button to defog and clear the windshield of a thin covering of ice.
Climate Control A Fan speed: Controls the volume of air circulated in your vehicle. Rotate the control to select the desired fan speed. The setting is shown in the display. B On and off button: Press the button to switch the system on and off. C Recirculated air: Press the button to switch between outside air and recirculated air. The air currently in the passenger compartment recirculates. This can reduce the time needed to cool the interior and reduce unwanted odors from entering your vehicle.
Climate Control Temperature Control Note: Do not place objects under the front seats as this may interfere with the airflow to the rear seats. Note: Remove any snow, ice or leaves from the air intake area at the base of the windshield. Manual Climate Control Note: To reduce fogging of the windshield during humid weather, adjust the air distribution control to the windshield air vents position. Increase the temperature and fan speed to improve clearing, if required.
Climate Control Heating the Interior Quickly Vehicles With Manual Climate Control Vehicles With Automatic Climate Control 1 Adjust the fan speed to the highest speed setting. Adjust the fan speed to the highest speed setting. 2 Adjust the temperature control to the highest setting. Adjust the temperature control to the highest setting. 3 Adjust the air distribution control to the Press the footwell button to distribute footwell air vents position. air to the footwell air vents.
Climate Control Recommended Settings for Cooling Vehicles With Manual Climate Control Vehicles With Automatic Climate Control 1 Adjust the fan speed to the second speed setting. Press the AUTO button. 2 Adjust the temperature control to the midway point of the cold settings. Adjust the temperature control to the desired setting. 3 Adjust the air distribution control to the Open all instrument panel air vents and instrument panel air vents position. direct as desired.
Climate Control Vehicles With Manual Climate Control 4 Adjust the fan speed to the highest setting. 5 Direct the instrument panel side air vents toward the side windows. 6 Close the instrument panel vents. Vehicles With Automatic Climate Control Maximum Cooling Performance in Instrument Panel or Instrument Panel and Footwell Positions Heated Windshield 1. Heated Rear Window Adjust the temperature control to the lowest setting. 2. Press the A/C and recirculated air buttons. 3.
Seats • SITTING IN THE CORRECT POSITION WARNINGS Do not recline the seat backrest too far as this can cause the occupant to slide under the safety belt, resulting in serious injury in the event of a crash. • Sitting improperly, out of position or with the seat backrest reclined too far, can result in serious injury or death in the event of a crash. Always sit upright against your seat backrest, with your feet on the floor.
Seats Rear Outer Head Restraint 1. Press button A to move the restraint rearward. 2. To move the restraint forward pull the headrest. 1. Press and hold the locking button. 2. Using a suitable implement release the retaining clip. Rear Center Head Restraint Removing the Head Restraint Press the locking buttons and remove the head restraint. 1. Press and hold the locking button. 2. Using a suitable implement release the retaining clip.
Seats Adjusting the Height of the Driver’s Seat MANUAL SEATS WARNINGS Do not place cargo or any objects behind the seatback before returning it to the original position. Pull on the seatback to make sure that it has fully latched after returning the seatback to its original position. An unlatched seat may become dangerous if you stop suddenly or have a collision. Rock the seat backward and forward after releasing the lever to make sure that it is fully engaged in its catch.
Seats 1. Push the locking lever 2. Fold the seat forward. Make sure that the seatback is in the folded position and securely latched. 3. Push the locking lever to return the seatback to the vertical position. Make sure that the seatback is securely latched in position. 1. Lower the head restraints. See Head Restraints (page 82). Press and hold the seatback unlock buttons. 2. Push the seatback forward. As the seatback lowers the seat cushion automatically lowers.
Seats HEATED SEATS FRONT SEAT ARMREST WARNING People who are unable to feel pain to their skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion or other physical conditions, must exercise care when using the heated seat. The heated seat may cause burns even at low temperatures, especially if used for long periods of time. Do not place anything on the seat that insulates against heat, such as a blanket or cushion.
Auxiliary Power Points 12 Volt DC Power Point Location Power points may be found: • on the center console • on the rear of the center console. WARNING Do not plug optional electrical accessories into the cigar lighter socket. Incorrect use of the lighter can cause damage not covered by your warranty, and can result in fire or serious injury. CIGAR LIGHTER Note: Do not hold the cigar lighter element pressed in.
Storage Compartments CUP HOLDERS Note: Stow items in the cupholder carefully as items may become loose during hard braking, acceleration or crashes, including hot drinks which may spill. WARNING Use only soft cups in the cup holders. Hard objects can injure you in a crash.
Starting and Stopping the Engine GENERAL INFORMATION IGNITION SWITCH WARNINGS Extended idling at high engine speeds can produce very high temperatures in the engine and exhaust system, creating the risk of fire or other damage. Do not park, idle or drive your vehicle on dry grass or other dry ground cover. The emission system heats up the engine compartment and exhaust system, creating the risk of fire. 0(off) - The ignition is off.
Starting and Stopping the Engine Starting a Diesel Engine Note: A valid key must be located inside your vehicle to switch the ignition on and start the engine. Note: Engine cranking will not commence until the engine glow plug indicator has extinguished. This may take several seconds in extremely cold conditions. Ignition On Press the button once. It is located on the instrument panel near the steering wheel.
Starting and Stopping the Engine Stopping the Engine When Your Vehicle is Stationary STEERING WHEEL LOCK VEHICLES WITHOUT: KEYLESS ENTRY AND PUSH BUTTON START Note: The ignition, all electrical circuits warning lamps and indicators will be switched off. WARNING Manual Transmission Always check that the steering is unlocked before attempting to move your vehicle. Press the button. Automatic Transmission 1. Move the transmission selector lever to position P. 2. Press the button.
Starting and Stopping the Engine Unlocking the Steering Wheel Switch the ignition on to unlock the steering wheel. If you have difficulty starting the engine when the temperature is below -13°F (-25°C), press the accelerator pedal to the mid-way point of its travel and try again. Note: You may have to rotate the steering wheel slightly to assist unlocking. Flooded Engine Vehicles with Manual Transmission STARTING A GASOLINE ENGINE 1. Fully depress the clutch pedal. 2.
Starting and Stopping the Engine 2. Turn the key to position III until the engine has started. Failure to Start STARTING A DIESEL ENGINE If the engine does not crank when the clutch pedal has been fully depressed and the ignition key is turned to position III. Vehicles With Manual Transmission Cold or Hot Engine 1. Fully depress the clutch and brake pedals. 2. Turn the key to position III until the engine has started.
Starting and Stopping the Engine The diesel particulate filter on your vehicle requires periodic regeneration to maintain its correct function. Your vehicle will carry out this process automatically. Release the accelerator pedal. Wait until the engine has reached idle speed and then switch it off. If your journeys meet one of the following conditions: • You drive only short distances. • You frequently switch the ignition on and off. • Your journeys contain a high level of acceleration and deceleration.
Unique Driving Characteristics AUTO-START-STOP Note: For vehicles with auto-start-stop, the battery requirement is different. It must be replaced by one of exactly the same specification as the original. Note: When the auto-start-stop indicator flashes amber, shift into neutral or press the clutch pedal. Note: If the system detects a malfunction, it will switch off. Have your vehicle checked by an authorized dealer.
Unique Driving Characteristics The system may automatically restart the engine under certain conditions, for example: • Low battery voltage. • To maintain the interior climate.
Fuel and Refueling • SAFETY PRECAUTIONS WARNINGS Do not overfill the fuel tank. The pressure in an overfilled tank may cause leakage and lead to fuel spray and fire. The fuel system may be under pressure. If you hear a hissing sound near the fuel filler door (Easy Fuel capless fuel system), do not refuel until the sound stops. Otherwise, fuel may spray out, which could cause serious personal injury. • Automotive fuels can cause serious injury or death if misused or mishandled.
Fuel and Refueling FUEL QUALITY - GASOLINE WARNINGS Use diesel that meets the specification defined by EN 590 or the relevant national specification. WARNINGS Do not mix gasoline with oil, diesel or other liquids. This could cause a chemical reaction. Note: We recommend that you use only high quality fuel. Do not use leaded gasoline or gasoline with additives containing other metallic compounds (e.g. manganese-based). They could damage the emission system.
Fuel and Refueling Refilling With a Portable Fuel Container 1. Locate the plastic funnel in the glove box. 2. Slowly insert the funnel into the capless fuel system. 3. Fill your vehicle with fuel from the portable fuel container. 4. When done, clean the funnel or properly dispose of it. Extra funnels can be purchased from your authorized dealer if you choose to dispose of the funnel. WARNINGS Do not insert the nozzle of portable fuel containers or aftermarket funnels into the capless fuel system.
Fuel and Refueling REFUELING WARNINGS Do not attempt to start the engine if you have filled the fuel tank with the incorrect fuel. This could damage the engine. Have the system checked by an authorized dealer immediately. Do not use any kind of flames or heat near the fuel system. The fuel system is under pressure. There is a risk of injury if the fuel system is leaking. 1.
Fuel and Refueling FUEL CONSUMPTION We derive CO2 and fuel consumption figures in laboratory tests according to Regulation (EC) 715/2007 or CR (EC) 692/2008 and subsequent amendments. They are intended as a comparison between makes and models of vehicles. They are not intended to represent the real world fuel consumption you may get from your vehicle.
Fuel and Refueling Calculating Fuel Economy 4. Subtract your initial odometer reading from the current odometer reading. 5. Calculate fuel economy by dividing miles traveled by gallons used (For Metric: Multiply liters used by 100, then divide by kilometers traveled). Do not measure fuel economy during the first 1000 mi (1,600 km) of driving (this is the engine break-in period). A more accurate measurement is obtained after 2500 mi (4,000 km).
Transmission Selector Lever Positions MANUAL TRANSMISSION Selecting Reverse Gear Do not engage reverse gear when your vehicle is moving. This can cause damage to the transmission. AUTOMATIC TRANSMISSION WARNINGS Always set the parking brake fully and make sure you move the transmission selector lever to position P. Switch the ignition off and remove the key whenever you leave your vehicle. Do not apply the brake pedal and accelerator pedal simultaneously.
Transmission Select drive to shift automatically through the forward gears. WARNINGS Apply the parking brake and move the transmission selector lever to park before leaving your vehicle. Make sure that the transmission selector lever is latched in position. The transmission will select the appropriate gear for optimum performance based on ambient temperature, road gradient, vehicle load and your input.
Transmission Hints on Driving With an Automatic Transmission Emergency Park Position Release Lever WARNING WARNINGS Do not drive your vehicle until you verify that the brake lamps are working. Do not idle the engine for long periods of time in drive with the brakes applied. If the parking brake is fully released, but the brake warning lamp remains illuminated, the brakes may not be working correctly. See an authorized dealer. Moving Off 1. Release the parking brake. 2.
Transmission The system makes it easier to pull away when your vehicle is on a slope without the need to use the parking brake. When the system is active, your vehicle will remain stationary on the slope for two to three seconds after you release the brake pedal. This allows you time to move your foot from the brake to the accelerator pedal. The brakes are released automatically once the engine has developed sufficient drive to prevent your vehicle from rolling down the slope.
Transmission Your vehicle comes with the system already enabled. If desired, you can disable the feature: See General Information (page 62).
Brakes GENERAL INFORMATION HINTS ON DRIVING WITH ANTI-LOCK BRAKES WARNING Note: When the system is operating, the brake pedal will pulse and may travel further. Maintain pressure on the brake pedal. You may also hear a noise from the system. This is normal. The system does not relieve you of your responsibility to drive with due care and attention. Note: Occasional brake noise is normal. If a metal-to-metal, continuous grinding or continuous squeal sound is present, the brake linings may be worn-out.
Brakes Note: If you park your vehicle on a hill and facing uphill select first gear and turn the steering wheel away from the curb. Note: If you park your vehicle on a hill and facing downhill select reverse gear and turn the steering wheel toward the curb. All Vehicles Note: Do not press the release button while pulling the lever up. To apply the parking brake: 1. Press the foot brake pedal firmly. 2. Pull the parking brake lever up to its fullest extent. To release the parking brake: 1.
Stability Control PRINCIPLE OF OPERATION Stability Control Warning Lamp Electronic Stability Program While driving, it flashes when the system is operating. See Warning Lamps and Indicators (page 57). WARNING The system does not relieve you of your responsibility to drive with due care and attention. Failure to do so could result in loss of vehicle control, personal injury or death. USING STABILITY CONTROL Note: The system automatically switches on every time you switch the ignition on.
Parking Aids Note: The outer sensors may detect the side walls of a garage. If the distance between the outer sensors and the side wall remains constant for three seconds, the alert will turn off. As you continue the inner sensors will detect objects directly behind your vehicle. PRINCIPLE OF OPERATION WARNINGS The system does not relieve you of your responsibility to drive with due care and attention. If your vehicles has a non-Ford approved trailer tow module the system may not correctly detect objects.
Parking Aids The parking aid system gives an audible warning and reduces the radio volume when it detects a large object within a limited range of your vehicle’s bumpers. Note: When the parking aid system no longer detects a large object the radio volume will return to the previous level. Rear Sensing System The rear parking aid sensors turn on automatically when you move the transmission selector lever to R (reverse) and your vehicle is moving at a speed of less than 3 mph (5 km/h).
Parking Aids Front and Rear Sensing System Audible warnings will sound when large objects are within the sensor coverage areas of either bumper in the following manner: • You will hear a high-pitched tone from the front audio system speakers when large objects are within the sensor coverage area of your vehicle’s front bumper. Moving your vehicle closer to a large object will increase the audible warning repeat rate.
Parking Aids Move the transmission selector lever from R (reverse), D (drive), L (low) or move away from large objects as you drive off, or press the parking aid button to switch the system off. For item location: See At a Glance (page 9). If a fault is present in the system, a warning message appears in the information display and does not allow you to switch the system on. Switch the ignition and the audio unit on.
Parking Aids Note: When reversing with a trailer the camera shows the direction of your vehicle and not the direction of the trailer. Note: If the camera image is not clear, clean the camera lens with a soft cloth. Turning the Rear View Camera Off Press the parking aid switch in the instrument panel or disengage reverse gear. For switch location: See At a Glance (page 9). Note: The system will automatically turn off once your vehicle speed has reached approximately 7 mph (12 km/h).
Cruise Control Note: Cruise control will disengage if your vehicle speed decreases more than 10 mph (16 km/h) below your set speed while driving uphill. PRINCIPLE OF OPERATION WARNING The system does not relieve you of your responsibility to drive with due care and attention. Switching Cruise Control On Press and release ON. Cruise control allows you to control your speed using the switches on the steering wheel. You can use cruise control when you exceed approximately 20 mph (30 km/h).
Cruise Control Switching Cruise Control Off Press and release OFF or switch the ignition off. Note: You erase the set speed when you switch the system off.
Driving Aids ACTIVE CITY STOP WARNINGS If you install a windshield not approved by us, the system may not function correctly. General Information WARNINGS The system does not relieve you of your responsibility to drive with due care and attention. If the engine stops after the system has been switched on, the hazard warning flashers will turn on. The system may not function when driving around sharp curves.
Driving Aids Laser Sensor Information In certain situations it is advisable to disable the system, for example: • Driving off road when objects may cover the windshield. • Driving through a car wash facility. You can switch the system off and on using the information display. See General Information (page 62). Active City Stop Relearning Procedure Note: When you disconnect the battery, the system will go through a relearning procedure. During this time the system will not be available.
Load Carrying GENERAL INFORMATION REAR UNDER FLOOR STORAGE WARNINGS Use load securing straps to an approved standard, e.g. DIN. Adjustable Load Floor Make sure that you secure all loose items properly. Place luggage and other loads as low and as far forward as possible within the luggage or loadspace. Do not drive with the liftgate or rear door open. Exhaust fumes may enter your vehicle. Do not exceed the maximum front and rear axle loads for your vehicle. See Vehicle Identification Plate (page 180).
Load Carrying Removing the Cover CARGO NETS Installing and Removing the Net Installing the Net DOG GUARD WARNING Keep a small distance between the dog guard and the rear seats. 1. Raise the rear outer head restraints. See Head Restraints (page 82). 2. Attach the top securing clips to the head restraint guides. 3. Attach the bottom securing clips to the bottom anchor points. Removing the Net 1. Raise the rear outer head restraints. See Head Restraints (page 82). 2.
Load Carrying 122 B-MAX (CB2) Vehicles Built From: 10-03-2014 Vehicles Built Up To: 03-05-2015, CG3573en enGBR, Edition date: 02/2014, Third Printing
Towing • TOWING A TRAILER WARNINGS Do not exceed 62 mph (100 km/h). This could result in the loss of vehicle control, serious personal injury or death. The rear tire pressures must be increased by 3 psi (0.2 bar) above specification. Do not exceed the maximum pressure stated on the tire sidewall. This could cause serious personal injury. See Wheels and Tires (page 165). • • Do not exceed the maximum gross train weight stated on your vehicle identification plate.
Towing Unlocking the Tow Ball Arm Mechanism Note: Not all vehicles are suitable or approved to have tow bars fitted. See an authorized dealer for further information. Trailer Lighting The electrical system on your vehicle is not suitable for towing trailers with LED lamps. TOW BALL WARNINGS When not in use, always transport the tow ball arm securely fastened in the luggage compartment. 1. Remove the protecting cap. 2. Insert the key and turn it clockwise to unlock. 3. Hold the tow ball arm.
Towing Before starting your journey, make sure that the tow ball arm is correctly locked. Check that: • • • • Note: Pull out the plug. the green marks are aligned the handwheel (A) is correctly fitted to the tow ball arm you have removed the key (B) the tow ball arm is securely positioned. Removing the Tow Ball Arm 1. Insert the tow ball arm vertically and press it upwards until it engages. Note: Do not hold your hand near the handwheel.
Towing Maintenance Note: Unhitch the trailer. 1. Remove the protecting cap. Press the cap into the key bow. Insert the key and unlock. 2. Hold the tow ball arm. Pull the handwheel out, turn it clockwise against the stop. 3. Remove the tow ball arm. 4. Release the handwheel. WARNING Remove the tow ball arm and protect the seat with the plug before steam cleaning your vehicle. Keep the system clean.
Towing Rear Towing Hook WARNINGS When towing your vehicle you must select neutral. Failure to follow this warning could damage the transmission and may lead to a crash or injury. Drive off slowly and smoothly without jerking the vehicle that is being towed. You must only use the towing eye that was delivered with your vehicle. See Towing Points (page 126). Tow ropes or rigid towing bars must be placed on the same side. For example; right hand rear towing point to right hand front towing point.
Towing Note: Using a rigid towing bar is the safest way to tow a vehicle. WARNINGS The brake and steering assistance will not operate unless the engine is running. Press the brake pedal harder and allow for increased stopping distances and heavier steering. Failure to take care may lead to a crash or personal injury. The weight of the vehicle that is being towed must not exceed the weight of the towing vehicle.
Driving Hints BREAKING-IN DRIVING THROUGH WATER Tires WARNINGS Drive through water in an emergency only and not as part of normal driving. WARNING New tires need to be run-in for approximately 300 miles (500 kilometers). During this time, you may experience different driving characteristics. Engine damage can occur if water enters the air filter. In an emergency, you can drive your vehicle through water to a maximum depth of 8 inches (200 millimeters) and at a maximum speed of 6 mph (10 km/h).
Driving Hints WARNINGS Pedals that cannot move freely can cause loss of vehicle control and increase the risk of serious personal injury. Always make sure that the floor mats are properly attached to the retention posts in the carpet that are supplied with your vehicle. Floor mats must be properly secured to both retention posts to make sure mats do not shift out of position. To install floor mats, position the floor mat so that the eyelet is over the retention post and press down to lock in.
Roadside Emergencies HAZARD WARNING FLASHERS In the event of a moderate to severe crash, your vehicle is fitted with a fuel pump shut-off feature that stops the flow of fuel to the engine. Not every impact will cause a shut-off. The hazard warning button is located on the instrument panel. Use it when your vehicle is creating a safety hazard for other motorists. Should the engine turn off after a crash, you may restart the engine by carrying out the following.
Roadside Emergencies JUMP STARTING THE VEHICLE WARNINGS Do not use fuel lines, engine rocker covers or the intake manifold as grounding points. C Positive connection cable D Negative connection cable 1. Position the vehicles so that they do not touch one another. 2. Switch off the engine and any electrical equipment. 3. Connect the positive (+) terminal of vehicle B with the positive (+) terminal of vehicle A (cable C). Connect batteries with only the same nominal voltage.
Roadside Emergencies 3. Run both vehicles for a minimum of three minutes before disconnecting the cables. WARNING Do not switch on the headlamps when disconnecting the cables. The peak voltage could blow the bulbs. Disconnect the cables in the reverse order.
Fuses Passenger Compartment Fuse Box FUSE BOX LOCATIONS This fuse box is located behind the glove box. Open the glove box and empty the contents. Press the sides inwards and swivel the glove box downward.
Fuses FUSE SPECIFICATION CHART Engine Compartment Fuse Box Fuse Fuse rating 1 30 A Anti-lock brake system module Stability assist module 2 60 A Cooling system fan high speed 40 A Cooling system fan 30 A Cooling system fan low speed 4 30 A Heater blower 5 60 A Passenger compartment fuse box supply (battery) 6 30 A Body control module 3 Circuits protected 135 B-MAX (CB2) Vehicles Built From: 10-03-2014 Vehicles Built Up To: 03-05-2015, CG3573en enGBR, Edition date: 02/2014, Third Prin
Fuses Fuse Fuse rating 7 60 A Passenger compartment fuse box supply (ignition) 60 A Glow plugs (Diesel engines) 50 A DPS6 module 8 Circuits protected 9 40 A Heated windshield left-hand side 10 40 A Heated windshield right-hand side 11 30 A Starter relay 12 10 A High beam left-hand relay 13 10 A High beam right-hand relay 14 15 A Run on pump 15 20 A Ignition coil 16 15 A Powertrain control module High and low cooling fan 17 15 A Heated oxygen sensors (gasoline engines) Po
Fuses Fuse Fuse rating Circuits protected 31 - 32 20 A Horn Battery saver Keyless vehicle module 33 20 A Heated rear window 34 20 A Fuel pump relay Diesel fuel heater 35 15 A Category 1 alarm system 36 7.
Fuses Relay Circuits switched Diesel fuel heater R12 Reversing lamp R13 Heater blower Passenger Compartment Fuse Box Fuse Fuse rating 1 7.
Fuses Fuse Fuse rating Circuits protected Heated windshield Dome lamp Interior mirror 2 10 A Stop lamps 3 3A Reversing lamp 4 7.5 A Headlamp leveling 5 - 6 15 A Not used Rear window wiper 7 15 A Washer pump 8 - 9 15 A Passenger heated seat 10 15 A Driver heated seat 11 - 12 10 A Airbag module 13 10 A Ignition Electric power assisted steering Instrument cluster Passive anti-theft system Anti-lock brake system 14 7.
Fuses Fuse Fuse rating Circuits protected Navigation 22 7.5 A Instrument cluster 23 7.
Fuses Fuse Fuse rating Circuits protected 44 7.
Fuses If electrical components in your vehicle are not working, a fuse may have blown. A break in the fuse wire will indicate a blown fuse. Check the appropriate fuses before replacing any electrical components.
Maintenance GENERAL INFORMATION • Have your vehicle serviced regularly to help maintain its roadworthiness and resale value. There is a large network of Ford authorized repairers that are there to help you with their professional servicing expertise. Authorized repairers are best qualified to service your vehicle properly and expertly, with a wide range of highly specialized tools. • In addition to regular servicing, we recommend that you carry out the following checks.
Maintenance 2. Move the catch to the left. 3. Open the hood and support it with the hood strut. Closing the Hood 1. Remove the hood strut from the catch and secure correctly after use. 2. Lower the hood and allow it to drop from under its own weight for the last 8 - 11 inches (20 – 30 centimeters). Note: Make sure that you have closed the hood correctly.
Maintenance UNDER HOOD OVERVIEW - 1.0L ECOBOOST™ * * A Engine coolant reservoir : See Engine Coolant Check (page 149). B Brake and clutch fluid reservoir (right-hand drive) : See Brake and Clutch Fluid Check (page 150). C Engine oil filler cap : See Engine Oil Check (page 148). D Battery: See Changing the 12V Battery (page 150). E Brake and clutch fluid reservoir (left-hand drive) : See Brake and Clutch Fluid Check (page 150). * * * F Engine compartment fuse box. See Fuses (page 134).
Maintenance UNDER HOOD OVERVIEW - 1.4L DURATEC-16V (SIGMA)/1.6L DURATEC-16V TI-VCT (SIGMA) * * A Engine coolant reservoir : See Engine Coolant Check (page 149). B Brake and clutch fluid reservoir (right-hand drive) : See Brake and Clutch Fluid Check (page 150). C Engine oil filler cap : See Engine Oil Check (page 148). D Battery: See Changing the 12V Battery (page 150). E Brake and clutch fluid reservoir (left-hand drive) : See Brake and Clutch Fluid Check (page 150).
Maintenance UNDER HOOD OVERVIEW - 1.5L DURATORQ-TDCI DIESEL/1.6L DURATORQ-TDCI (DV) DIESEL * * A Engine coolant reservoir : See Engine Coolant Check (page 149). B Brake and clutch fluid reservoir (right-hand drive) : See Brake and Clutch Fluid Check (page 150). C Engine oil filler cap : See Engine Oil Check (page 148). D Battery: See Changing the 12V Battery (page 150). E Brake and clutch fluid reservoir (left-hand drive) : See Brake and Clutch Fluid Check (page 150).
Maintenance ENGINE OIL DIPSTICK - 1.0L ECOBOOST™ A Minimum B Maximum ENGINE OIL DIPSTICK - 1.5L DURATORQ-TDCI DIESEL/1.6L DURATORQ-TDCI (DV) DIESEL ENGINE OIL DIPSTICK - 1.4L DURATEC-16V (SIGMA)/1.6L DURATEC-16V TI-VCT (SIGMA) A Minimum B Maximum ENGINE OIL CHECK 1. Make sure that your vehicle is on level ground. 2. Switch off the engine and wait 10 minutes for the oil to drain into the oil pan. 3. Remove the dipstick and wipe it with a clean, lint free cloth.
Maintenance Adding Oil Adding Engine Coolant WARNINGS Only add oil when the engine is cold. If the engine is hot, wait 10 minutes for the engine to cool down. Failure to take care may result in personal injury. WARNINGS Only add coolant when the engine is cold. If the engine is hot, wait 10 minutes for the engine to cool down. Do not remove the filler cap when the engine is running. Do not remove the filler cap when the engine is running. Failure to take care may result in personal injury.
Maintenance BRAKE AND CLUTCH FLUID CHECK WARNINGS Do not use any fluid other than the recommended brake fluid as this will reduce brake efficiency. Use of incorrect fluid could result in the loss of vehicle control, serious personal injury or death. Only use brake fluid from a sealed container. Contamination with dirt, water, petroleum products or other materials may result in brake system damage or failure.
Maintenance Note: You must reset the bounce-back feature for the power windows. See Power Windows (page 52). Changing the Windshield Wiper Blades Make sure that you dispose of old batteries in an environmentally friendly way. Seek advice from your local authority about recycling old batteries. CHECKING THE WIPER BLADES 1. Press the locking buttons together. 2. Rotate and remove the wiper blade. 3. Install in the reverse order. Note: Make sure that the wiper blade locks into place.
Maintenance 4. Remove the wiper blade. 5. Install in the reverse order. Note: Make sure that the wiper blade locks into place. REMOVING A HEADLAMP 1. Open the hood. See Opening and Closing the Hood (page 143). Note: Make sure that the wiper arm does not spring back against the glass when the wiper blade is not attached. Note: To avoid damage to the internal structure of the wiper blade, only move it using the center connection of the wiper arm.
Maintenance Note: When fitting the headlamp, make sure that you reconnect the electrical connector correctly. Note: When fitting the headlamp, make sure that you fully engage the headlamp in the lower fixing point. CHANGING A BULB WARNINGS Switch the lamps and the ignition off. Let the bulb cool down before removing it. Do not touch the glass of the bulb. A Headlamp high beam B Headlamp low beam C Direction indicator Direction Indicator 1. Note: Only fit bulbs of the correct specification.
Maintenance 3. Gently press the bulb into the bulb holder, turn it counterclockwise and remove it. Headlamp High Beam 3. Turn the bulb holder counterclockwise and remove it. 4. Remove the bulb. Note: Do not touch the glass of the bulb. 1. Side Lamp Remove the headlamp. See Removing a Headlamp (page 152). 1. 2. Remove the cover. 3. Disconnect the electrical connector. 4. Release the clip and remove the bulb. Note: Do not touch the glass of the bulb. 2. Remove the cover. 3. Remove the bulb holder. 4.
Maintenance 1. Carefully remove the side repeater. 2. Remove the bulb holder. 3. Remove the bulb. Approach Lamp 2. Remove the lamp. 3. Remove the bulb. Note: Position the mirror glass as far inward as possible. Front Fog Lamps 1. Insert a screwdriver into the gap between the mirror housing and the mirror glass and release the metal retaining clip. Note: You cannot separate the fog lamp bulb from the bulb holder. 1. Disconnect the electrical connector. 2.
Maintenance Rear Lamps Direction Indicator, Tail and Brake Lamp 1. 5. Remove the bulb holder. 6. Gently press the bulb into the bulb holder, turn it counterclockwise and remove it. A. Tail and brake lamp B. Direction indicator Remove the trim panel. Reversing Lamp and Fog Lamp 2. Disconnect the electrical connector. 3. Remove the wing nut. 4. Remove the lamp. 1. Open the liftgate. 2. Remove the trim panel.
Maintenance 3. Disconnect the electrical connector. 4. Turn the bulb holder counterclockwise and remove it. 5. Gently press the bulb into the bulb holder, turn it counterclockwise and remove it. 3. Insert a suitable object into the holes. 4. Carefully pull the lamp toward the front of the vehicle to release the spring clips. Central High Mounted Brake Lamp 5. Remove the lamp. 1. Open the liftgate. 2. Detach the clips.
Maintenance Interior Lamp 1. Carefully remove the lamp. 2. Turn the bulb holder counterclockwise and remove it. 3. Remove the bulb. 6. Remove the bulb holder. 7. Remove the bulb. Licence Plate Lamp Reading Lamps 1. Carefully release the spring clip. 2. Remove the lamp. 3. Remove the bulb. 1. Carefully remove the lamp. 2. Turn the bulb holder counterclockwise and remove it. 3. Remove the bulb.
Maintenance Luggage Compartment Lamp, Footwell Lamp and Liftgate Lamp 1. Carefully prize out the lamp. 2. Remove the bulb.
Maintenance Note: LED lamps are not serviceable. TECHNICAL SPECIFICATIONS Vehicle Fluids Note: Use fluids which meet the specifications or requirements defined. Use of other fluids may lead to damage which is not covered by your warranty. Specification Viscosity Grade Engine oil - gasoline engines only WSS-M2C948-B 5W-20 Castrol or Ford Engine Oil Alternative engine oil - all gasoline engines except 1.
Maintenance Variant Item Capacity in gallons (liters) All Windshield and rear window washer system 0.6 (2.5) 1.0L EcoBoost Engine cooling system approximately 1.4 (6.3) Vehicles with a gasoline engine except 1.0L EcoBoost Engine cooling system approximately 1.2 (5.5) Vehicles with a diesel engine Engine cooling system approximately 1.3 (6) Vehicles with a gasoline engine Fuel tank 10.6 (48) Vehicles with a diesel engine Fuel tank 10.3 (47) 1.
Maintenance Variant Item Capacity in gallons (liters) 1.5L Duratorq-TDCi Engine lubrication system - excluding the oil filter 0.8 (3.4) 1.6L Duratorq-TDCi Engine lubrication system - including the oil filter 0.8 (3.8) 1.6L Duratorq-TDCi Engine lubrication system - excluding the oil filter 0.8 (3.5) Engine Oil Adding Capacities Engine Capacity in gallons (liters) 1.0L EcoBoost 0.2 (0.8) 1.4L Duratec-16V and 1.6L Duratec-16V Ti-VCT 0.2 (0.8) 1.5L Duratorq-TDCi 0.4 (1.6) 1.
Vehicle Care Note: Industrial-strength (heavy-duty) cleaners, or cleaning chemicals, may cause damage over a period of time. CLEANING THE EXTERIOR Note: If you use a car wash with a waxing cycle, make sure that you remove the wax from the windshield and the wiper blades. Body Paintwork Preservation Note: Prior to using a car wash facility check the suitability of it for your vehicle. WARNINGS Do not polish your vehicle in strong sunshine. Note: Some car washes use water at high pressure.
Vehicle Care Rear Windows Note: Some automatic car washes may cause damage to the finish on your wheel rims and covers. Note: Do not use any abrasive materials to clean the interior of the rear windows. Alloy wheels and wheel covers are coated with a clear coat paint finish. To maintain their condition we recommend that you: • Clean them weekly with the recommended wheel and tire cleaner. • Use a sponge to remove heavy deposits of dirt and brake dust accumulation.
Wheels and Tires GENERAL INFORMATION WARNINGS Do not use the kit on run flat tires. A decal with tire pressure data is located in the driver’s door opening. Do not try to seal damage to the tire’s sidewall. Check and set the tire pressure at the ambient temperature in which you are intending to drive your vehicle and when the tires are cold. The kit seals most tire punctures [with a diameter of up to ¼ inch (six millimeters)] to temporarily restore mobility.
Wheels and Tires • • • • • • Park your vehicle at the roadside so that you do not obstruct the flow of traffic and so that you are able to use the kit without being in danger. Apply the parking brake, even if you have parked on a level road, to make sure that your vehicle will not move. Do not attempt to remove foreign objects like nails or screws penetrating the tire. Leave the engine running while the kit is in use, but not if your vehicle is in an enclosed or poorly ventilated area (e.
Wheels and Tires H Repair kit hose I Pressure relief valve Note: When pumping in the sealant through the tire valve, the pressure may rise up to 87 psi (6 bar) but will drop again after about 30 seconds. 1. Remove the kit from the wrapping. 2. Peel off the label A showing the maximum permissible speed of 50 mph (80 km/h) from the sealant bottle and attach it to the instrument panel in the driver’s field of view. Make sure the label does not obscure anything important. 3.
Wheels and Tires 19. Attach the kit and read the tire pressure from the pressure gauge E. 20. Adjust it to the specified pressure. See Technical Specifications (page 178). 21. Once you have inflated the tire to its correct tire pressure, move the compressor switch G to position 0, remove the power plug F from the socket, unscrew the hose C and fasten the valve cap. 22. Leave hose C and H connected to the sealant bottle B and store the kit away safely. 23.
Wheels and Tires USING SNOW CHAINS WARNINGS Do not drive on significantly under-inflated tires. This may cause the tires to overheat and fail. Under-inflation reduces fuel efficiency, tire tread life and may also affect your ability to drive your vehicle safely. WARNINGS Do not exceed 30 mph (50 km/h). Do not use snow chains on snow-free roads. Do not bend or damage the valves when you are inflating the tires. Only fit snow chains to specified tires. See Technical Specifications (page 178).
Wheels and Tires System Reset As a driver assistance feature, your vehicle has a tire pressure monitoring system. A warning lamp will illuminate when one or more of the tires are significantly under-inflated. If the low tire pressure warning lamp illuminates, you should stop your vehicle as soon as it is safe to do so, check the tires and inflate them to the correct pressure. Note: Do not reset the system when your vehicle is moving.
Wheels and Tires Understanding the Tire Pressure Monitoring System replacing one or more tires or wheels on your vehicle. Make sure the replacement tires or wheels allow the system to continue to function correctly. See When the Temporary Spare Tire is Installed in this section. The system measures the pressure in the four road tires and sends the tire pressure readings to your vehicle.
Wheels and Tires Warning lamp Description Action Solid warning lamp Tire(s) under-inflated Spare tire in use 1. Make sure tires are at the correct pressure. See Wheels and Tires (page 165). The tire pressures are also on the tire inflation pressure label (located on the edge of driver door or the B-Pillar). 2. After inflating the tires to the correct pressure you must carry out the tire pressure monitoring system reset procedure. See Tire Pressure Monitoring System Reset Procedure in this chapter.
Wheels and Tires The tires need to be periodically rotated to provide consistent performance and maximum tire life, the system needs to know when the tires have been rotated to determine which set of tires are on the front and rear axles. With this information, the system can detect and correctly warn of low tire pressures. Carrying Out the System Reset Procedure Switch the ignition on.
Wheels and Tires WARNINGS Do not carry out any tire repairs on a spare wheel. WARNINGS Never place anything between the jack and the ground, or the jack and your vehicle. Do not drive through an automatic car wash. Note: Vehicles with a temporary mobility kit do not have a vehicle jack or a wheel brace. If you are unsure what type of spare wheel you have do not exceed 50 mph (80 km/h). It is recommended to use a workshop type hydraulic jack for changing between summer and winter tires.
Wheels and Tires A Emergency use only B Maintenance A Small arrow-shaped marks on the sills show the location of the jacking points.
Wheels and Tires Removing the Wheel Trim Assembling the Wheel Brace WARNING The screw-in towing eye has a left-hand thread. Turn it counterclockwise to install it. Make sure that the towing eye is fully tightened. 1. Insert the wheel trim remover. 2. Remove the wheel trim. Note: Make sure that you pull the wheel trim remover at right angles to the trim. Removing a Road Wheel WARNINGS Park your vehicle in such a position that neither the traffic nor you are hindered or endangered.
Wheels and Tires 3. Jack up your vehicle until the tire is clear of the ground. 4. Remove the lug nuts and the wheel. Note: Do not lay alloy wheels face down on the ground, this will damage the paint. WARNINGS Secure the diagonally opposite wheel with an appropriate block or wheel chock. Make sure that the arrows on directional tires point in the direction of rotation when your vehicle is moving forward.
Wheels and Tires 4. Partially tighten the lug nuts in the sequence shown. 5. Lower your vehicle and remove the jack. 6. Fully tighten the lug nuts in the sequence shown. See Technical Specifications (page 178). 7. Install the wheel trim using the ball of your hand. WARNING Have the lug nuts checked for tightness and the tire pressure checked as soon as possible.
Wheels and Tires Up to 100mph (160 km/h) Normal load Variant * Tire size Full load Front Rear Front Rear lbf/in² (bar) lbf/in² (bar) lbf/in² (bar) lbf/in² (bar) All engines 185/60 R15 * 33 (2.3) 29 (2) 36 (2.5) 41 (2.8) All engines 195/60 R15 32 (2.2) 29 (2) 36 (2.5) 46 (3.2) All engines 195/55 R16 32 (2.2) 29 (2) 36 (2.5) 41 (2.8) All engines 205/45 R17 33 (2.3) 29 (2) 36 (2.5) 41 (2.8) Only fit snow chains to specified tires.
Capacities and Specifications Note: Your vehicle identification plate design may vary to that shown. VEHICLE IDENTIFICATION PLATE A Model B Variant C Engine designation D Engine power and emission level E Vehicle identification number F Gross vehicle weight G Gross train weight H Maximum front axle weight I Maximum rear axle weight Note: The information shown on the vehicle identification plate is dependent upon market requirements.
Capacities and Specifications The vehicle identification number is stamped into the floor panel on the right-hand side, beside the front seat. It is also shown on the left-hand side of the instrument panel. VEHICLE IDENTIFICATION NUMBER TECHNICAL SPECIFICATIONS Vehicle dimensions Dimension description Dimension in inches (mm) Maximum length 160.5 (4077) Overall width including exterior mirrors 81.4 (2067) Overall height - EC curb weight 63.1 - 63.5 (1604 - 1613) Wheelbase 98.
Capacities and Specifications Towing equipment dimensions 182 B-MAX (CB2) Vehicles Built From: 10-03-2014 Vehicles Built Up To: 03-05-2015, CG3573en enGBR, Edition date: 02/2014, Third Printing
Capacities and Specifications Item Dimension description Dimension in inches (mm) A Bumper – end of tow ball 3.1 (78) B Attachment point – center of tow ball 0.7 (18) C Wheel center – center of tow ball D Center of tow ball – side member 20.3 (516) E Distance between side members 40.6 (1032) F Center of tow ball – center 1. attachment point 16.5 (419) G Center of tow ball – center 2. attachment point 26.3 (668) 33.
Audio System GENERAL INFORMATION Radio Frequencies and Reception Factors Radio reception factors Distance and Strength The further you travel away from an FM station, the weaker the signal and the weaker the reception. Terrain Hills, mountains, tall buildings, bridges, tunnels, freeway overpasses, parking garages, dense tree foliage and thunderstorms can interfere with the reception.
Audio System • • MP3 and WMA folder mode represents a folder structure consisting of one level of folders. The CD player numbers all MP3 and WMA tracks on the disc (noted by the MP3 or WMA file extension) and all folders containing MP3 and WMA files, from F001 (folder) T001 (track) to F253 T255. Creating discs with only one level of folders helps with navigation through the disc files.
Audio System A Eject: Press the button to eject a CD. B Cursor arrows: Press a button to scroll through on-screen choices. C CD slot: Where you insert a CD. D OK: Press the button to confirm on-screen selections. E INFO: Press the button to access radio, CD, USB and IPod information. F TA: Press the button to turn traffic announcements on or off and cancels announcements during an active announcement. G Numeric keypad: Press the button to recall a previously stored station.
Audio System K MENU: Press the button to access different audio system features. L SOUND: Press the button to adjust the sound settings for bass, treble, middle, balance and fade. M AUX: Press the button to access the AUX and SYNC features, it will also cancel the menu or list browsing. N RADIO: Press the button to select different radio bands, it will also cancel the menu or list browsing. O CD: Press the button to change source to CD, it will also cancel the menu or list browsing.
Audio System 3. Press and hold one of the preset buttons. A progress bar and message will appear. When the progress bar completes the station has been stored. The audio unit will also mute momentarily as confirmation. When traffic information is broadcast, it will automatically interrupt normal radio or CD playback and Traffic announcement will appear in the display.
Audio System 1. 2. 3. 4. 5. Press the MENU button and select AUDIO or AUDIO SETTINGS. Select AVC LEVEL or ADAPTIVE VOL. Use the left or right arrow button to adjust the setting. Press the OK button to confirm your selection. Press the MENU button to return. When selected, the unit continually evaluates signal strength and if a better signal becomes available, the unit will switch to that alternative.
Audio System 2. Select AUDIO or AUDIO SETTINGS. 3. Scroll to RDS REGIONAL and turn on or off with the OK button. 4. Press the MENU button to return. Note: An integrated multi function display is situated above the unit. This shows important information regarding control of your system. Additionally, there are various icons placed around the display screen which light up when a function is active (for example CD, Radio or Aux.
Audio System A Eject: Press the button to eject a CD. B Cursor arrows: Press a button to scroll through on-screen choices. C CD slot: Where you insert a CD. D OK: Press the button to confirm on-screen selections. E INFO: Press the button to access radio, CD, USB and IPod information. F TA: Press the button to turn traffic announcements on or off and cancels announcements during an active announcement.
Audio System J Function button 3: Press the button to select different functions of the audio system depending on which mode (i.e. radio or CD) you are in. K Seek up: Press the button to go to the next station up the radio frequency band or the next track on a CD. L On, Off and Volume: Press the button to switch the audio system on or off. Turn the dial to adjust the volume. M Seek down: Press the button to go to the next station down the radio frequency band or the previous track on a CD.
Audio System You can use the selector to return to radio reception when you have been listening to another source. Alternatively, press the left arrow button to display the available wavebands. Scroll to the required waveband and press OK. Station Tuning Control DAB Service Linking Note: The system does not automatically turn on every time you switch the ignition on.
Audio System Traffic Information Control 1. Press function button 3. 2. Use the seek buttons to scan up or down the selected waveband. 3. Press function button 3 again or OK to continue listening to a station. Many stations that broadcast on the FM waveband have a TP code to signify that they carry traffic program information.
Audio System Ending Traffic Announcements Alternative Frequencies The audio unit will return to normal operation at the end of each traffic announcement. To end the announcement prematurely, press TA or TRAFFIC during the announcement. The majority of programs that broadcast on the FM waveband have a program identification code, it can be recognized by audio units.
Audio System large network may be broken down into a number of smaller regional networks, typically centered on major towns or cities. When the network is not split into regional variants, the whole network caries the same programming. AUDIO UNIT - VEHICLES WITH: AM/FM/CD/NAVIGATION SYSTEM Regional mode ON: This prevents random alternative frequency switches when neighboring regional networks are not carrying the same programming.
Audio System A Eject: Press the button to eject a CD. B Cursor arrows: Press a button to scroll through on-screen choices. C CD slot: Where you insert a CD. D OK: Press the button to confirm on-screen selections. E INFO: Press the button to access radio, CD, USB, IPod and Navigation information. If Navigation has been selected, pressing this button will show details of your current location or journey. F MAP Press the button to enter the map screen. See Navigation (page 262).
Audio System J Function button 3: Press the button to select different functions of the audio system depending on which mode (i.e. radio or CD) you are in. K Seek up: Press the button to go to the next station up the radio frequency band or the next track on a CD. L On, Off and Volume: Press the button to switch the audio system on or off. Turn the dial to adjust the volume. M Seek down: Press the button to go to the next station down the radio frequency band or the previous track on a CD.
Audio System Manual Tuning 1. Press function button 2. 2. Use the left and right arrow buttons to tune down or up the frequency band in small increments or press and hold to increment quickly, until you find a station you want to listen to. 3. Press OK to continue listening to a station. Scan Tuning Scan allows you to listen to a few seconds of each station detected. A 1. Press function button 3. 2. Use the seek buttons to scan up or down the selected frequency band. 3.
Audio System Autostore Control Traffic Announcement Volume Note: This will store up to a maximum of the 10 strongest signals available, either from the AM or the FM frequency band, and overwrite the previously stored stations. You can also store stations manually in the same way as other frequency bands. Traffic announcements interrupt normal broadcasts at a preset minimum level that is usually louder than normal listening volumes.
Audio System News Broadcasts It will restore radio reception when it finds one or if one is not found, the unit will return to the original stored frequency. The audio unit may interrupt normal reception to broadcast news bulletins from stations on the FM frequency band, radio data system or other enhanced network linked stations. When selected, AF may appear in the display. Press the MENU button. The display will indicate there is an incoming announcement, during news broadcasts.
Audio System Action AUDIO UNIT - VEHICLES WITH: SONY AM/FM/CD Message 1 Audio settings 2 RDS regional WARNING Driving while distracted can result in loss of vehicle control, crash and injury. We strongly recommend that you use extreme caution when using any device that may take your focus off the road. Your primary responsibility is the safe operation of your vehicle. We recommend against the use of any hand-held device while driving and encourage the use of voice-operated systems when possible.
Audio System A On, Off: Press the button to switch the audio system on or off. B DISPLAY: Press the button to turn on the display into idle mode. C Numeric keypad: Press the button to recall a previously stored station. To store a favorite station press and hold until the sound returns. In CD mode, press a number to select a track. In phone mode, use the buttons to dial a phone number. D CD slot: Where you insert a CD. E Cursor arrows: Press the button to scroll through on-screen choices.
Audio System J Seek up: Press the button to go to the next station up the radio frequency band or the next track on a CD when in CD mode. In phone mode, use the button to end a phone call. An incoming call can be rejected. K MUTE: Press the button to turn the sound off, press again to turn the sound on. L TA: Press the button to turn traffic announcements on or off and cancels announcements during an active announcement.
Audio System You can use the selector to return to radio reception when you have been listening to another source. Alternatively, press the left arrow button to display the available wavebands. Scroll to the required waveband and press OK. Station Tuning Control DAB Service Linking Note: The system does not automatically turn on every time you switch the ignition on.
Audio System Traffic Information Control 1. Press function button 3. 2. Use the seek buttons to scan up or down the selected waveband. 3. Press function button 3 again or OK to continue listening to a station. Many stations that broadcast on the FM waveband have a TP code to signify that they carry traffic program information.
Audio System Ending Traffic Announcements 2. Select AUDIO or AUDIO SETTINGS. 3. Scroll to the required digital signal processing function. 4. Press the OK button. 5. Use the up and down arrow buttons to select the required setting. 6. Press the OK button to confirm your selection. 7. Press the MENU button to return. The audio unit will return to normal operation at the end of each traffic announcement. To end the announcement prematurely, press TA or TRAFFIC during the announcement.
Audio System When selected, the unit continually evaluates signal strength and, if a better signal becomes available, the unit will switch to that alternative. It mutes while it checks a list of alternative frequencies and if necessary, it will search once across the selected waveband for a genuine alternative frequency.
Audio System A On, Off: Press the button to switch the audio system on or off. B NAV: Press the button to access the navigation system. C Numeric keypad: Press the button to recall a previously stored station. To store a favorite station press and hold until the sound returns. In CD mode, press a number to select a track. In phone mode, use the buttons to dial a phone number. D CD slot: Where you insert a CD. E Cursor arrows: Press the button to scroll through on-screen choices.
Audio System J Seek up: Press the button to go to the next station up the radio frequency band or the next track on a CD when in CD mode. In phone mode, use the button to end a phone call. An incoming call can be rejected. K HOME: Press the button to access the address menu, to start navigating to your home address or to change your home address. L TRAFFIC: Press the button to turn traffic announcements on or off and cancel an active announcement.
Audio System You can use the selector to return to radio reception when you have been listening to another source. Alternatively, press the left arrow button to display the available wavebands. Scroll to the required waveband and press OK. Station Tuning Control DAB Service Linking Note: The system does not automatically turn on every time you switch the ignition on.
Audio System Traffic Information Control 1. Press function button 3. 2. Use the seek buttons to scan up or down the selected waveband. 3. Press function button 3 again or OK to continue listening to a station. Many stations that broadcast on the FM waveband have a TP code to signify that they carry traffic program information.
Audio System Ending Traffic Announcements 2. Select AUDIO or AUDIO SETTINGS. 3. Scroll to the required digital signal processing function. 4. Press the OK button. 5. Use the up and down arrow buttons to select the required setting. 6. Press the OK button to confirm your selection. 7. Press the MENU button to return. The audio unit will return to normal operation at the end of each traffic announcement. To end the announcement prematurely, press TA or TRAFFIC during the announcement.
Audio System When selected, the unit continually evaluates signal strength and, if a better signal becomes available, the unit will switch to that alternative. It mutes while it checks a list of alternative frequencies and if necessary, it will search once across the selected waveband for a genuine alternative frequency. 2. Select AUDIO or AUDIO SETTINGS. 3. Scroll to RDS REGIONAL and turn on or off with the OK button. 4. Press the MENU button to return.
Audio System Radio Station Tuning Control 1. Select a radio station. 2. Press and hold one of the preset buttons. A progress bar and message will appear. When the progress bar completes the radio station has been stored. The system will mute momentarily as confirmation. Press the RADIO button and select DAB1 or DAB2. Both preset banks operate in the same way and can store up to 10 different preset radio stations.
Audio System 1. Press the MENU button and select CD MODE. 2. Select SHUFFLE. This enables the function to be switched on or off. AUDIO SYSTEM SECURITY Each unit incorporates a unique code that is linked to the vehicle identification number. The system will automatically check that the audio unit and vehicle match before allowing operation. When an MP3 CD is playing, options include SHUFFLE for the whole CD, or to play all the tracks in the folder in a random order.
Audio System You can play MP3 files recorded on CD-ROM, CD-R and CD-RW formats. The disc must be in the ISO 9660 level 1 or level 2 format, or Joliet or Romeo in the expansion format. You can also use a disc recorded in multi session. File Formats With formats other than ISO 9660 level 1 and level 2, folder names or file names may not be displayed correctly. When naming, be sure to add the file extension .MP3 or .WMA to the file name. ISO 9660 Format If you put the extension .MP3 or .
Audio System To specify a desired playback order before the folder or file name. Input the order by number (e.g., 01, 02) then record contents onto a disc. The order differs depending on the writing software. MP3 or WMA Navigation MP3 tracks may be recorded on the CD in several ways. They can all be placed in the root directory like a conventional audio CD, or they can be placed in folders that may represent, for example, an album, artist, or genre.
Audio System CD Text Display Options Track Selection When an audio disc with CD text is playing, limited information encoded in each track can be displayed. Such information will normally include: • Press the seek down button once to replay the current track. If pressed within two seconds of the start of a track, the previous track plays. • • • • Press the up or down arrow buttons to select the required track, then press OK. The disc name. The artist name. The track name.
Audio System Note: When an MP3 CD is playing, you can have the system shuffle tracks for the whole CD or within the current folder. Pressing function button 3 toggles these options. Conventional CDs begin at a CD control area called the lead-in and end at an area called lead-out. A multi session CD is a CD having multiple sessions, with each segment from lead-in to lead-out regarded as a single session.
Audio System • • If an MP3 or WMA file is on the disc, the system skips these file and other data. Audio CD data is not recognized. If no MP3 or WMA file is in the disc, nothing plays. Audio CD data is not recognized. • • MP3 and WMA Files Playback Order The playback order of the folders and files are as shown. Note: The system skips any folder that does not include an MP3 or WMA file.
Audio System MP3 and WMA Display Options AUDIO INPUT JACK When an MP3 or WMA disc is playing, certain information encoded in each track can display. Such information normally includes: • • • WARNINGS Driving while distracted can result in loss of vehicle control, accident and injury. We strongly recommend that you use extreme caution when using any device or feature that may take your focus off the road. Your primary responsibility is the safe operation of your vehicle.
Audio System 2. Plug the extension cable from the portable music player into the auxiliary input jack. 3. Switch the radio on. Select either a tuned FM station or a CD. 4. Adjust the volume as desired. 5. Switch the portable music player on and adjust its volume to half its maximum level. 6. Press AUX until LINE or LINE IN appears in the display. You should hear music from your device even if it is low. 7.
SYNC™ GENERAL INFORMATION SYNC is an in-vehicle communications system that works with your Bluetooth-enabled cell phone and portable media player. • This allows you to: • Make and receive calls • Access and play music from your media player • Use Emergency Assistance • Access phonebook contacts and music using voice commands • Stream music from your connected cell phone • Select pre-defined text messages Make sure that you review your device's manual before using it with SYNC.
SYNC™ Safety Information supported media content. The system also records a short development log of approximately 10 minutes of all recent system activity. The log profile and other system data may be used to improve the system and help diagnose any problems that may occur. WARNING Driving while distracted can result in loss of vehicle control, crash and injury. We strongly recommend that you use extreme caution when using any device that may take your focus off the road.
SYNC™ Before giving a voice command, wait for the system announcement to finish followed by a single beep. Any command spoken before this does not register with the system. You can interrupt the system at any time while it is speaking by pressing the voice button. You can also cancel a voice session at any time by pressing and holding the voice button. Speak naturally, without long pauses between words. Initiating a Voice Session Press the voice button.
SYNC™ Command Description interaction mode advanced Provides less audible interaction and more tone prompts. interaction mode novice Provides more detailed interaction and guidance. Press the voice button. When prompted: Confirmation prompts are short questions the system asks when it is not sure of your request or when there is more than one possible response to your request. For example, the system may ask if the command phone is correct.
SYNC™ Changing the Voice Settings the information and entertainment display. You can change the voice settings using Press the MENU button. Action Message 1 SYNC-Settings 2 Voice settings Note: To scroll through the menus, press the up or down arrows on your audio system. USING SYNC™ WITH YOUR PHONE 1. Make sure the Bluetooth feature on your cell phone is switched on before starting the search. Refer to your device's manual if necessary. 2. Press the PHONE button.
SYNC™ The information display may show your cell phone's battery charge level and signal strength. 6. When a message to begin pairing appears in the audio display, search for SYNC on your device to start the pairing process. 7. Select SYNC on your cell phone. 8. Wait until the PIN appears on the phone display. Compare the PIN on the phone with the PIN shown in the audio display and accept the request on the phone and the vehicle display. The display indicates when the pairing is successful.
SYNC™ Command Action (hold call [on] | (put | place) call on hold) These commands are only available during a call. (hold call off | take call off hold) These commands are only available during a call. mute [call] [on] These commands are only available during a call. (mute [call] off | Unmute These commands are only available during a call. [call]) join (call | calls) These commands are only available during a call.
SYNC™ Command (turn ringer on | silent mode off) (turn ringer off | silent mode [on]) Words in parentheses or brackets are optional and do not have to be spoken for the system to understand the command. Making a Call Press the voice button and when prompted say either: Command Action call (someone | [[a] name]) dial [[a] number] Followed by a number.
SYNC™ Receiving a Call • When receiving a call, you can: • Answer the call by pressing the accept call button on the steering wheel or by selecting the accept call option in the audio display. Press the OK button. • Reject the call by pressing the reject call button on the steering wheel or by selecting the reject call option in the audio display. Press the OK button. Cell Phone Options During an Active Call Message Ignore the call by doing nothing.
SYNC™ Message Description and Action 4. Press the OK button again when the desired selection appears in the audio display. 5. Press the OK button or dial button to call the selection. Call history Access your call history log. 1. Select the option for more. 2. Scroll to the option until call history appears. Press the OK button. 3. Scroll through your call history options (incoming, outgoing or missed). 4. Press the OK button again when the desired selection appears in the audio display. 5.
SYNC™ Message Description and Action 3. Press the OK button again when the desired selection appears in the audio display. 4. Press the OK button or dial button to call the selection. Call history Access any previously dialed, received or missed calls. 1. Press the OK button to select. 2. Scroll to select either incoming calls, outgoing calls or missed calls. Press the OK button to make your selection. 3. Press the OK button or dial button to call the selection.
SYNC™ Message Action Reply to sender Press the OK button to access and then scroll through the list of pre-defined messages to send. Call sender Press the OK button to call the sender of the message. Forward msg. Press the OK button to forward the message to anyone in your phonebook or call history. You can also choose to enter a number. 2. Select the text messaging option, then press the OK button. Sending, Downloading and Deleting Your Text Messages 1.
SYNC™ Accessing Your Cell Phone Settings download. 1. Press the PHONE button. 2. Scroll until the phone settings option appears, then press the OK button. 3. Scroll to select from the following options: These are cell phone dependent features.
SYNC™ Message Description and Action Add contacts Push the desired contacts on your cell phone. Refer to your device's manual on how to push contacts. Press the OK button to add more contacts from your phonebook. Delete When a message asking you to delete appears, select the option to confirm. Press the OK button to delete the current phonebook and call history. The system takes you back to the menu for phone settings.
SYNC™ Message Description and Action 4. Wait until the PIN appears on the phone display. Compare the PIN on the phone with the PIN shown in the audio display and accept the request on the phones and the vehicles display. The display indicates when the pairing * is successful. 5. When the option to set the cell phone as the primary cell phone appears, select either yes or no. 6.
SYNC™ Message Description and Action Bluetooth on Check or uncheck this option to turn the Bluetooth interface of the system on or off. Select this option then press the OK button to change the option's status. Set defaults This selection does not erase your indexed information (phonebook, call history, text messages and paired devices). Select this option and confirm when prompted in the audio display. Return to the factory default settings.
SYNC™ Message SYNC-Apps Description and Action Scroll to this option, and then press OK. If a crash deploys an airbag or triggers the fuel pump shut off, the system may contact emergency services by dialing 112 (the wireless emergency number that works in most European countries) through a paired and connected cell phone. For more information about the system and Emergency Assistance, visit the regional Ford website.
SYNC™ Display Options In the Event of a Crash If you switch on this feature, a confirmation message appears in the display. Note: Not every crash deploys an airbag or triggers the fuel pump shut off (which may turn on Emergency Assistance). However, if Emergency Assistance is triggered the system tries to contact the emergency services. If a connected cell phone sustains damage or loses connection to the system, it searches for and tries to connect to any available previously paired cell phone.
SYNC™ • • After the delivery of the introductory message the voice line opens so that you can speak hands-free with the emergency operator. When the line is connected, you must be prepared to provide your name, phone number and location information immediately. • • You do not have a valid and registered SIM card with credit in your cell phone. You are in a European country or region where the SYNC Emergency Assistance cannot place the call. Visit the regional Ford website for details.
SYNC™ Note: For information on available apps, supported smartphone devices and troubleshooting tips please visit the Ford website. To Access Using the SYNC Menu Scroll through the list of available applications and press OK to select an app. Once an app is running through SYNC, press the right arrow button to access the app menu. You can access various app features from here, for example thumbs up and thumbs down. Press the left arrow button to exit the app menu.
SYNC™ Command Description and Action find [new] [mobile] (apps | applications) The system will search your connected mobile device for SYNC compatible apps. Say the name of an app to start it on SYNC. Help The system will list the available voice commands for the requested app. (quit | exit | close) Use this command followed by the name of the app.
SYNC™ App Status in the settings menu. There are three possible statuses: You can view the current status of an app Message Description and Action Update needed The system has detected a new app requiring authorization or a general permissions update is required. Up-to-date No update is required. Updating... The system is trying to receive an update.
SYNC™ • To allow your vehicle to provide location information, including: GPS and speed. To allow the app to send push notifications using the vehicle display and voice capabilities while running in a background state. • Confirm that the USB device has been formatted correctly and has the following specifications: • USB 2.0. • File format must be FAT16/32. • Supply current not greater than 500mA. Note: You will only need to grant permissions the first time you use an app with SYNC.
SYNC™ Message Browse USB Description and Action Depending on how many media files are on your connected device, an indexing message may appear in the display. When indexing is complete, the screen returns to the playback menu.
SYNC™ Voice Command Then any of the following: (browse | search | show) playlist Voice Command (browse | search | show) all (album | albums) play pause play [album] [by [artist]] (browse | search | show) all (artist | artists) * (browse | search | show) all (genre | genres) Play all play [artist] * play [genre] * (browse | search | show) all (playlist | playlists) [play] next track play [playlist] (browse | search | show) all (song | songs | title | titles | file | files | track | tracks) *
SYNC™ The system is also capable of playing music from your cell phone through Bluetooth. Voice Command To switch the Bluetooth audio on, use the AUX or Source button or press the voice button and when prompted and say: Description and Action Bluetooth audio Then any of the following: Voice Command Description and Action pause play [play] next track [play] previous track Press AUX to select USB playback.
SYNC™ Message Description and Action Shuffle Choose to shuffle or repeat your music. Once you make your choice, it remains on until you switch it off. Repeat track Choose to shuffle or repeat your music. Once you make your choice, it remains on until you switch it off. Similar music You can play similar types of music to the current playlist from the USB port. The system uses the metadata information of each track to compile a playlist.
SYNC™ Message Play all Description and Action Play all indexed media files from your playing device one at * a time in numerical order. 1. Press OK to select. The first track title appears in the display. Playlists Access your playlists from formats, ASX, M3U, WPL or MTP. 1. Press OK to select. 2. Scroll to select the desired playlist, and then press OK. Songs Search for and play a specific indexed track. 1. Press OK to select. 2. Scroll to select the desired track, and then press OK.
SYNC™ Message Description and Action Browse USB Browse all supported media files on your media player connected to the USB port. You can only view media files that are compatible with SYNC; other saved files are not visible. 1. Press OK to select. 2. Scroll to browse indexed media files on your flash drive, and then press OK. Reset USB Resets the USB index. After the new indexing is complete, you can choose what to play from the USB song library.
SYNC™ Cell phone issues Issue Possible cause Possible solution Try pushing your phonebook contacts to SYNC by selecting the option to add. You must switch on your cell phone and the automatic phonebook download feature on SYNC. Try pushing your phonebook contacts to SYNC by selecting the option to add. The system says "Phonebook downloaded" but my Limitations on your cell SYNC phonephone's capability. book is empty or is missing contacts. This is a cell phonedependent feature.
SYNC™ Cell phone issues Issue Possible cause Possible solution • • • • Make sure the connection status shows Not Connected. Press the blue circle to enter the next menu. Turn on Show Notifications. Turn on Sync Contacts. Your iPhone is now set up to forward incoming text messages to SYNC. Repeat these steps for every other Sync vehicle you are connected to. Your iPhone will only forward incoming text messages to SYNC if it is unlocked. Replying to text messages using SYNC is not supported by iPhone.
SYNC™ USB and media issues Issue Possible cause Possible solution Try switching off the device, resetting it or removing the battery, then trying again. I am having trouble connecting my device. Make sure you are using the manufacturer's cable. Possible device malfuncMake sure correctly insert the USB cable to tion. the device and your vehicle's USB port. Make sure that the device does not have an auto-install program or active security settings.
SYNC™ Voice command issues Issue SYNC does not understand what I am saying. Possible cause Possible solution Review the cell phone voice commands and the media voice commands at the beginning of their respective sections. You may be using the wrong voice commands. Refer to the audio display during an active voice session to find a list of voice commands there. You may be speaking too The microphone for the system is either in soon or at the wrong your rear view mirror or in the headliner just time.
SYNC™ Voice command issues Issue Possible cause Possible solution You may not be saying the name exactly as the system saved it. Make sure you are saying the name exactly as the system saved it. For example, if the contact name is Joe Wilson, say "Call Joe Wilson". The system works better if you list full names such as "Joe Wilson" rather than "Joe". Contacts in your phonebook may be very short and similar or they may contain special characters.
SYNC™ Voice command issues Issue Possible cause Possible solution SYNC uses a synthetically generated voice rather than pre-recorded human voice. The system generates voice prompts and SYNC uses text-tothe pronuncispeech voice prompt ation of some technology. words may not be accurate for my language. My previous Bluetooth voice control system allowed me to control the radio, CD, and climate control systems.
SYNC™ General Issue The language selected for the instrument cluster and information and entertainment display does not match the SYNC language (phone, USB, Bluetooth audio, voice control and voice prompts). Possible cause Possible solution SYNC only supports four languages in a single module for text display, voice control and voice prompts. The country where you bought your vehicle dictates the four languages based on the most popular languages spoken.
SYNC™ AppLink issues Issue Possible cause(s) Possible solution(s) AppLink Mobile An AppLink capable Applications: phone is not connected When I select to SYNC. "Find New Apps," SYNC does not find any applications. Ensure you have a compatible smartphone; an Android with OS 2.3 or higher or an iPhone 3GS or newer with iOS 5.0 or higher. Additionally, ensure your phone is paired and connected to SYNC in order to find AppLink-capable apps on your device.
SYNC™ AppLink issues Issue Possible cause(s) Possible solution(s) My Android phone is connected, my app(s) are running, I restarted them, but I still cannot find any apps. There is a bluetooth bug on some order versions of the Android OS that may cause apps that were found on your previous vehicle drive to not be found again if you have not turned off bluetooth. Reset the Bluetooth on your phone by turning it off and then turning Bluetooth back on.
Navigation Press the relevant button on the unit bezel to access the system functions. This will take you into the selected mode. For instructions on how to operate the audio unit and the available navigation features, see the relevant audio unit procedure. See Audio System (page 184). Loading Map Data WARNINGS The indicated maximum speed may not be applicable to your vehicle. It is always your responsibility to control your vehicle, supervise any system and obey the correct speed limit.
Navigation Note: You are ultimately responsible for the safe operation of your vehicle and must evaluate whether it is safe to follow route suggestions. Navigation features are provided only as an aid. Driving decisions based on observations of local conditions and existing traffic regulations must be observed. Do not follow route suggestions if they would result in an unsafe or illegal maneuver, an unsafe situation, or if you would be directed into an area that you consider unsafe.
Navigation Message Unblock route sections Destination input Country City/postcode Street District Start guidance Traffic TA TMC for route All TMC Block next section Route sections list Unblock route sections Home address Start guidance Change address Last destinations Favourites Favourites (A-Z) Points of interest POIs nearby Near destination Along motorway POIs near address Search by name Tour planning New tour Stored tours Store position Route options Route: Eco Fast Short 264 B-MAX (CB2)
Navigation Message Always ask Driver: Leisurely Normal Fast Eco settings Trailer: Roof box Dynamic Motorway Tunnel Ferry/motorail Toll Seasonal roads Toll sticker Special functions GPS info System info Enter position Demo mode Route Options Press the NAV button and scroll to route options. You can then set your route options for any of the following. Message Route: Always ask Description and Action Select to make sure that you are always given the choice of route option for your journey.
Navigation Message Short Driver: Eco settings Description and Action Uses the shortest distance possible. Leisurely This option will calculate your time of arrival based on a leisurely drive to the destination. Normal This option will calculate your time of arrival based on a normal drive to the destination. Fast This option will calculate your time of arrival based on a fast drive to the destination.
Navigation Message Description and Action Toll When switched off the system will avoid toll roads on your route and automatically update your route distance and timings. Seasonal roads When switched off the system will avoid seasonal roads (for example, mountain passes) on your route and automatically update your route distance and timings. Toll sticker When switched off the system will avoid toll routes and automatically update your route distance and timings.
Navigation Message Description and Action Store position Store and name your current position. This will automatically save in your favorites. Route options Set your route options from the available list. Special functions Select GPS and system information or a demonstration of the system functionality. Select a demonstration mode where the system will simulate a journey whilst the vehicle is stationary. You can manually select a vehicle start position.
Navigation Adjusting the Navigation Voice Level Nav Audio Mixing You can adjust the voice prompt level during an active voice prompt by using the volume control. This feature allows you to adjust the volume mix between the audio unit and navigation voice level. Note: During active route guidance pressing the information button will repeat the last navigation instruction. Tolerant Destination Input This function will search a number of destinations with a similar spelling to what you have entered.
Navigation Move Once an active route is underway, guidance will be given by on-screen information and voice prompts. Whichever audio source you wish to leave the unit in, basic turn by turn and distance information will remain on the screen in the form of a graphic inset. You do not need to leave the unit on the main navigation screen when you are navigating a route. Press the MAP button at any time to return to the main navigation screen.
Appendices ELECTROMAGNETIC COMPATIBILITY WARNINGS The radio frequency transmitter equipment, for example cellular telephones and amateur radio transmitters, may only be fitted to your vehicle if they keep to the parameters shown in the table below. There are no special provisions or conditions for installations or use. WARNINGS Your vehicle has been tested and certified to legislations relating to electromagnetic compatibility (72/245/EEC, UN ECE Regulation 10 or other applicable local requirements).
Appendices Frequency Band Maximum output power Watt (Peak MHz RMS) Antenna Positions 1-30 50 W 3 30-54 50 W 1, 2 68-87.5 50 W 1, 2 142-176 50 W 1, 2 380-512 50 W 1, 2 806-940 10 W 1, 2 1200-1400 10 W 1, 2 1710-1885 10 W 1, 2 1885-2025 10 W 1, 2 Note: After the installation of radio frequency transmitters, check for disturbances from and to all electrical equipment in your vehicle, both in the standby and transmit modes.
Appendices • • • and "online" or electronic documentation ("MS SOFTWARE") are protected by international intellectual property laws and treaties. The MS SOFTWARE is licensed, not sold. All rights reserved. The MS SOFTWARE may interface with and/or communicate with, or may be later upgraded to interface with and/or communicate with additional software and/or systems provided by FORD MOTOR COMPANY.
Appendices • • • • • Limitations on Distributing, Copying, Modifying and Creating Derivative Works: You may not distribute, copy, make modifications to or create derivative works based on the SOFTWARE, except and only to the extent that such activity is expressly permitted by applicable law notwithstanding this limitation. Single EULA: The end user documentation for the DEVICE and related systems and services may contain multiple EULAs, such as multiple translations and/or multiple media versions (e.g.
Appendices • • Internet-Based Services Components: The SOFTWARE may contain components that enable and facilitate the use of certain Internet-based services.
Appendices SOFTWARE onto the DEVICE as a replacement copy for the existing SOFTWARE, and use it in accordance with this EULA, including any additional EULA terms accompanying the upgrade SOFTWARE. the U.S. Export Administration Regulations, as well as end-user, end-use and destination restrictions issued by U.S. and other governments. For additional information, see http://www.microsoft.com/exporting/.
Appendices • THERE ARE NO WARRANTIES OTHER THAN THOSE THAT MAY EXPRESSLY BE PROVIDED FOR YOUR NEW VEHICLE. Keep User's Guide in vehicle: When kept in the vehicle, the User's Guide will be a ready reference for you and other users unfamiliar with the Windows Automotive-based system. Please make certain that before using the system for the first time, all persons have access to the User's Guide and read its instructions and safety information carefully.
Appendices Volume Setting: Do not raise the volume excessively. Keep the volume at a level where you can still hear outside traffic and emergency signals while driving. Driving while unable to hear these sounds could cause an accident. Route Safety: Do not follow the route suggestions if doing so would result in an unsafe or illegal maneuver, if you would be placed in an unsafe situation, or if you would be directed into an area that you consider unsafe.
Appendices 1. Safe and Lawful Use 3. Software License You acknowledge that devoting attention to the TeleNav Software may pose a risk of injury or death to you and others in situations that otherwise require your undivided attention, and you therefore agree to comply with the following when using the TeleNav Software: (a) observe all traffic laws and otherwise drive safely; (b) use your own personal judgment while driving.
Appendices defamatory, vulgar, obscene, libelous, or otherwise objectionable; and (f) lease, rent out, or otherwise permit unauthorized access by third parties to the TeleNav Software without advanced written permission of TeleNav. PARTICULAR PURPOSE AND NON-INFRINGEMENT OF THIRD PARTY RIGHTS WITH RESPECT TO THE TELENAV SOFTWARE. Certain jurisdictions do not permit the disclaimer of certain warranties, so this limitation may not apply to you. 4. Disclaimers 5.
Appendices 6. Arbitration and Governing Law cease all use of the TeleNav Software. Notwithstanding the foregoing, TeleNav may assign this Agreement to any other party at any time without notice, provided the assignee remains bound by this Agreement.
Appendices 8.4 NavTeq End User License Agreement TeleNav's or your failure to require performance of any provision shall not affect that party's right to require performance at any time thereafter, nor shall a waiver of any breach or default of this Agreement constitute a waiver of any subsequent breach or default or a waiver of the provision itself. END USER TERMS The content provided ("Data") is licensed, not sold.
Appendices TERMS AND CONDITIONS real time route guidance, fleet management or similar applications; or (b) with, or in communication with, including without limitation, cellular phones, palmtop and handheld computers, pagers, and personal digital assistants or PDAs. License Limitations on Use: You agree that your license to use this Data is limited to and conditioned on use for solely personal, noncommercial purposes, and not for service bureau, timesharing or other similar purposes.
Appendices CAUSE OF THE CLAIM, DEMAND OR ACTION ALLEGING ANY LOSS, INJURY OR DAMAGES, DIRECT OR INDIRECT, WHICH MAY RESULT FROM THE USE OR POSSESSION OF THIS DATA; OR FOR ANY LOSS OF PROFIT, REVENUE, CONTRACTS OR SAVINGS, OR ANY OTHER DIRECT, INDIRECT, INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF YOUR USE OF OR INABILITY TO USE THIS DATA, ANY DEFECT IN THIS DATA, OR THE BREACH OF THESE TERMS OR CONDITIONS, WHETHER IN AN ACTION IN CONTRACT OR TORT OR BASED ON A WARRANTY, EVEN IF NT OR ITS LICE
Appendices Gracenote® End User License Agreement (EULA) NAVTEQ CONTRACTOR (MANUFACTURER/SUPPLIER) This device contains software from Gracenote, Inc. of 2000 Powell Street Emeryville, California 94608 ("Gracenote"). ADDRESS: 425 West Randolph Street, Chicago, IL 60606.
Appendices Data, the Gracenote Software, and Gracenote Servers. Gracenote, respectively, reserve all rights in Gracenote Data, the Gracenote Software, and the Gracenote Servers and Gracenote Content, including all ownership rights. Under no circumstances will either Gracenote become liable for any payment to you for any information that you provide, including any copyrighted material or music file information.
Appendices The antenna used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
288 B-MAX (CB2) Vehicles Built From: 10-03-2014 Vehicles Built Up To: 03-05-2015, CG3573en enGBR, Edition date: 02/2014, Third Printing
Index A Audio System Security...............................216 Audio Troubleshooting..............................223 Audio Unit - Vehicles With: AM/FM/CD/ Bluetooth.....................................................190 A/C See: Climate Control...........................................74 Alternative Frequencies...................................195 Automatic Volume Control.............................195 Autostore Control...............................................194 News Broadcasts.............
Index B Audio Unit - Vehicles With: Navigation System/Sony AM/FM/CD.....................208 Alternative Frequencies....................................213 Automatic Volume Control.............................213 Autostore Control...............................................212 Digital Signal Processing.................................213 News Broadcasts................................................213 Regional Mode.....................................................214 Sound Button...................
Index Changing the Wiper Blades.......................151 Compact Disc Player - Vehicles With: AM/FM/CD...................................................216 Rear Window Wiper Blade...............................151 Windshield Wiper Blades.................................151 CD Text Display Options..................................219 Compact Disc Playback...................................216 Compact Disc Track Scanning......................216 Ending Compact Disc Playback....................
Index Engine Coolant Check................................149 Fuse Box Locations......................................134 Adding Engine Coolant.....................................149 Engine Compartment Fuse Box....................134 Passenger Compartment Fuse Box.............134 Engine Immobilizer Fuses.................................................................134 Fuse Specification Chart...........................135 See: Passive Anti-Theft System.....................39 Engine Oil Check.....
Index K Hints on Controlling the Interior Climate............................................................78 Cooling the Interior Quickly..............................79 General Hints.........................................................78 Heating the Interior Quickly..............................79 Maximum Cooling Performance in Instrument Panel or Instrument Panel and Footwell Positions..................................81 Recommended Settings for Cooling ...........
Index M O Maintenance...................................................143 Oil Check General Information..........................................143 Technical Specifications.................................160 Opening and Closing the Hood...............143 See: Engine Oil Check.......................................148 Manual Climate Control...............................75 Manual Liftgate...............................................36 Closing the Hood...........................................
Index Rear Seats........................................................85 Safety Precautions........................................97 Seats...................................................................82 Security..............................................................39 Side Airbags.....................................................25 Side Curtain Airbags......................................25 Sitting in the Correct Position...................82 Sliding Door.................................
Index SYNC™ Troubleshooting..........................252 Towing the Vehicle on Four Wheels Manual Transmission...............................127 Towing...............................................................123 Transmission..................................................103 Transmission T Tailgate See: Manual Liftgate...........................................36 See: Transmission..............................................103 Technical Specifications Trip Computer............................
Index W Using SYNC™ With Your Phone............228 Accessing Features Through the Cell Phone Menu..................................................................233 Accessing Your Cell Phone Settings...........236 Bluetooth Devices..............................................237 Cell Phone Options During an Active Call......................................................................232 Cell Phone Voice Commands.......................229 Making a Call................................................
298 B-MAX (CB2) Vehicles Built From: 10-03-2014 Vehicles Built Up To: 03-05-2015, CG3573en enGBR, Edition date: 02/2014, Third Printing
CG3573en
