Contents Before driving Introduction 2 Instrumentation 8 Controls and features Seating and safety restraints 21 104 Starting and driving Starting 147 Driving 152 Roadside emergencies 178 Servicing Maintenance and care 201 Capacities and specifications 248 Customer assistance 257 Reporting safety defects 270 Index 271 All rights reserved.
Introduction The following warning may be required by California law: CALIFORNIA Proposition 65 Warning WARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
Introduction Indicates a message regarding child safety restraints. Refer to Seating and safety restraints for more information. Indicates that this Owner Guide contains information on this subject. Please refer to the Index to locate the appropriate section which will provide you more information. WARNINGS Warnings provide information which may reduce the risk of personal injury and prevent possible damage to others, your vehicle and its equipment.
Introduction INFORMATION ABOUT THIS GUIDE The information found in this guide was in effect at the time of printing. Ford may change the contents without notice and without incurring obligation. EMISSION WARRANTY The New Vehicle Limited Warranty includes Bumper-to-Bumper Coverage, Safety Restraint Coverage, Corrosion Coverage, and 7.3L Power Stroke Diesel Engine Coverage. In addition, your vehicle is eligible for Emissions Defect and Emissions Performance Warranties.
Introduction SPECIAL NOTICES Using your vehicle with a snowplow Do not use this vehicle for snowplowing. Using your vehicle as an ambulance Do not use this vehicle as an ambulance. Your vehicle is not equipped with the Ford Ambulance Preparation Package. Notice to owners of pickup trucks and utility type vehicles Utility vehicles have a significantly higher rollover rate than other types of vehicles. Before you drive your vehicle, please read this Owner’s Guide carefully.
Introduction These are some of the symbols you may see on your vehicle.
Introduction Vehicle Symbol Glossary Child Safety Door Lock/Unlock Interior Luggage Compartment Release Symbol Panic Alarm Engine Oil Engine Coolant Engine Coolant Temperature Do Not Open When Hot Battery Avoid Smoking, Flames, or Sparks Battery Acid Explosive Gas Fan Warning Power Steering Fluid Maintain Correct Fluid Level Emission System Engine Air Filter Passenger Compartment Air Filter Jack MAX MIN Check fuel cap 7
Instrumentation Instrument cluster (pg. 10) Instrument panel dimmer switch (pg. 22) Driver air bag (pg. 128) Headlamp control (pg. 21) DOOR AJAR H 60 40 L 80 00 E L 40 60 0 MPH H RPMX1000 20 20 F THEFT H SELECT/RESET km/h D 2 P RN D C BRAKE CRUISE FUEL DOOR RES ON SET ACCEL OFF COAST PEDALS Power adjustable foot pedals (pg. 23) Rear window defroster control (pg. 23) 8 Hood release (pg. 202) Parking brake release (pg. 154) Speed control (pg. 69) Turn signal control (pg.
Instrumentation Audio system (pg. 27) Gearshift (includes overdrive button) (pg. 161) BASS BAL SEL TREB VOL PUSH ON CD EJ TAPE AM FM TUNE SEEK MUTE RDS SCAN AUTO REW FF SIDE 1.2 COMP SHUFF 1 2 3 5 6 LO A4WD FADE PANEL 4H A/C 4L MAX A/C HI OFF PANEL & FLOOR FLOOR FLR & DEF DEF COOL WARM 4WD control * (pg. 163) Auxiliary power point (pg. 26) Climate control system (pg.
Instrumentation WARNING LIGHTS AND CHIMES DOOR AJAR H 60 40 L LOW FUEL F SERVICE ENGINE SOON E FUEL DOOR 80 00 H RPMX1000 4X4 20 L 40 20 LOW RANGE 60 0 MPH THEFT H SELECT/RESET km/h D 2 P RN D CK SUSP C BRAKE CRUISE Low fuel Illuminates as an early reminder of a low fuel condition indicated on the fuel gauge (refer to Fuel Gauge in this chapter for more information).
Instrumentation What you should do if the Service Engine Soon light illuminates Light turns on solid: This means that the OBD II system has detected a malfunction. Temporary malfunctions may cause your Service Engine Soon light to illuminate. Examples are: 1. The vehicle has run out of fuel. (The engine may misfire or run poorly.) 2. Poor fuel quality or water in the fuel. 3. The fuel cap may not have been properly installed and securely tightened.
Instrumentation Safety belt Momentarily illuminates when the ignition is turned to the ON position to remind you to fasten your safety belts. For more information, refer to the Seating and safety restraints chapter. Brake system warning Momentarily illuminates when the ignition is turned to the ON position BRAKE to indicate a system check. Also ! illuminates if the parking brake is engaged. If the brake warning lamp does not illuminate at these times, seek service immediately.
Instrumentation High beams Illuminates when the high beam headlamps are turned on. SecuriLock姟 anti-theft system This light indicates the anti-theft alarm system is armed. Momentarily THEFT illuminates when the ignition is turned to ON. If the light fails to illuminate, continues to flash or remains on, have the system serviced. Refer to SecuriLock娂 passive anti-theft system in the Controls and features chapter.
Instrumentation Four wheel drive low (if equipped) Momentarily illuminates after the engine is started. Illuminates when four-wheel drive low is engaged. If the light continues to flash have the system serviced. Four wheel drive indicator (if equipped) Momentarily illuminates after the engine is started. Illuminates when 4x4 range is engaged. If the light continues to flash have the system serviced.
Instrumentation Speed control This light comes on when either the CRUISE COAST/SET or RES/ACCEL controls are pressed. It turns off when the speed control OFF control is pressed, the brake is applied or the ignition is turned to the OFF position. Safety belt warning chime Sounds to remind you to fasten your safety belts. For information on the safety belt warning chime, refer to the Seating and safety restraints chapter. Belt minder chime Sounds intermittently to remind you to fasten your safety belts.
Instrumentation GAUGES DOOR AJAR H 60 40 L LOW FUEL F SERVICE ENGINE SOON E 80 00 H RPMX1000 4X4 20 L 40 20 LOW RANGE 60 0 MPH THEFT H SELECT/RESET km/h D 2 P RN D CRUISE FUEL DOOR CK SUSP C BRAKE Fuel gauge Displays approximately how much fuel is in the fuel tank (when the key is in the ON position). The fuel gauge may vary slightly when the vehicle is in motion. The ignition should be in the OFF position while the vehicle is being refueled.
Instrumentation Speedometer Indicates the current vehicle speed. 60 40 80 00 20 40 20 60 0 MPH Engine coolant temperature gauge Indicates the temperature of the engine coolant. At normal operating temperature, the needle remains within the normal area (the area between the “H” and “C”). If it enters the red section, the engine is overheating. Stop the vehicle as soon as safely possible, switch off the engine immediately and let the engine cool.
Instrumentation Trip odometer Registers the kilometers (miles) of individual journeys. Press and release the reset button until a “T” appears in the display (this represents the trip mode). Press and hold the button for three seconds to reset. Tachometer Indicates the engine speed in revolutions per minute. Driving with your tachometer pointer continuously at the top of the scale may damage the engine. Battery voltage gauge This shows the battery voltage when the ignition is in the ON position.
Instrumentation Engine oil pressure gauge This shows the engine oil pressure in the system. Sufficient pressure exists as long as the needle remains H in the normal range (the area between the “L” and “H”). If the gauge indicates low pressure, stop the vehicle as soon as safely L possible and switch off the engine immediately. Check the oil level. Add oil if needed (refer to Engine oil in the Maintenance and care chapter).
Instrumentation Mode control Each press of the MODE control will display a different feature as follows: Fuel range. This displays the approximate number of kilometers (miles) left to drive before the fuel tank is empty. The indicated distance to empty may be inaccurate: • with sustained, drastic changes in fuel economy (such as trailer towing), but will eventually recover. • if the vehicle is started while parked on an incline. • if less than 27 liters (6 gallons) of fuel is added to the fuel tank.
Controls and features HEADLAMP CONTROL Rotate the headlamp control to the first position to turn on the parking lamps. Rotate to the second position to also turn on the headlamps. A High beams Push forward to activate. Pull toward you to deactivate. Flash to pass Pull toward you to activate and release to deactivate. Daytime running lamps (DRL) (if equipped) Turns the headlamps on with a reduced output.
Controls and features Always remember to turn on your headlamps at dusk or during inclement weather. The Daytime Running Lamp (DRL) system does not activate with your tail lamps and generally may not provide adequate lighting during these conditions. Failure to activate your headlamps under these conditions may result in a collision. Foglamp control (if equipped) The headlamp control also operates the foglamps.
Controls and features AUTOLAMP CONTROL The autolamp system provides light sensitive automatic on-off control of A the exterior lights normally controlled by the headlamp control. The autolamp system also keeps the lights on for approximately 20 seconds after the ignition switch is turned to OFF. • To turn autolamps on, rotate the control counterclockwise. • To turn autolamps off, rotate the control clockwise to OFF. • Foglamps are not controlled by the autolamps.
Controls and features The ignition must be in the ON position to operate the rear window defroster. The defroster turns off automatically after 10 minutes or when the ignition is turned to the OFF position. To manually turn off the defroster before 10 minutes have passed, push the control again. 4WD CONTROL (IF EQUIPPED) This control operates the 4WD. Refer to the Driving chapter for more information.
Controls and features This system is not designed to prevent contact with small or moving objects. The system is designed to provide a warning to assist the driver in detecting large stationary objects to avoid damaging the vehicle. The system may not detect smaller objects, particularly those close to the ground. The RSS will assist the driver in detecting certain objects while the vehicle slowly moves in reverse at speeds less than 6 km/h (4 mph).
Controls and features The reverse sensing system is OFF automatically enabled when the gear selector is placed in R (Reverse) and the ignition is ON. A reverse sensing control allows the driver to disable the reverse sensing system only when the ignition is ON, and the gear selector is in R (Reverse). The OFF indicator remains illuminated when the system is disabled. The system defaults to ON every time the reverse gear is selected. Press the control to disable or enable the system.
Controls and features Power outlets are designed for accessory plugs only. Do not hang any type of accessory or accessory bracket from the plug. Improper use of the power outlet can cause damage not covered by your warranty. A second auxiliary power point is located on the lower rear side of the console. The power point is accessible from the rear seats. USING YOUR AUDIO SYSTEM Your audio system is equipped with selective lighting, a unique lighting strategy.
Controls and features Premium AM/FM Stereo/Cassette (CD Changer Compatible) BASS BAL SEL TREB VOL PUSH ON CD EJ TAPE FM TUNE SEEK MUTE AM FADE REW FF SIDE 1.2 1 2 3 RDS SCAN 4 AUTO COMP SHUFF 5 6 Audiophile AM/FM Stereo/Cassette (CD Changer Compatible) BASS BAL SEL TREB VOL PUSH ON CD EJ TAPE AM 28 FM TUNE SEEK MUTE REW FF SIDE 1.
Controls and features Volume/power control Press the control to turn the audio system on or off. VOL PUSH ON Turn the control to raise or lower volume. VOL PUSH ON If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on. Speed sensitive volume (if equipped) With this feature, radio volume automatically changes slightly with vehicle speed to compensate for road and wind noise.
Controls and features • to increase volume compensation to decrease or shut off the • volume compensation AM/FM select The AM/FM select control works in radio, tape and CD modes (if equipped). SEL AM FM AM/FM select in radio mode This control allows you to select AM or FM frequency bands. Press the control to switch between AM, FM1 or FM2 memory preset stations. AM/FM select in tape mode Press this control to stop tape play and begin radio play.
Controls and features Tune adjust for CD changer • Press to select the previous TUNE disc in the CD changer. (Play will begin on the first track of the disc unless the CD changer is in shuffle mode.) Refer to Shuffle feature for more information. Hold the control to continue reversing through the discs. to select the next disc in the CD changer. Hold the control • Press to fast-forward through the remaining discs. Seek function The seek function control works in radio, tape or CD mode (if equipped).
Controls and features Scan function The scan function works in radio, tape or CD mode (if equipped). SCAN Scan function in radio mode Press the SCAN control to hear a brief sampling of all listenable stations on the frequency band. Press the SCAN control again to stop the scan mode. Scan function in tape mode Press the SCAN control to hear a short sampling of all selections on the tape. (The tape scans in a forward direction.
Controls and features Autoset memory preset Autoset allows you to set strong radio stations without losing your original manually set preset stations. This feature is helpful on trips when you travel between cities with different radio stations. Starting autoset memory preset 1. Select a frequency using the AM/FM select controls. 2. Press the AUTO control. 3. When the first six strong stations AUTO are filled, the station stored in memory preset control 1 will start playing.
Controls and features Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers. Press the BAL control. Use the SEL control to adjust the sound between the speakers. Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers. Press the FADE control. Use the SEL control to adjust the sound between the front and rear speakers.
Controls and features Rewind The rewind control works in tape REW and CD modes. 1 • In tape mode, radio play will continue until rewind is stopped (with the TAPE control) or the beginning of the tape is reached. • In CD mode, pressing the REW control for less than three seconds results in slow rewind. Pressing the control for more than three seconds results in fast rewind. Fast forward The fast forward control works in FF tape and CD modes (if equipped).
Controls and features Dolby姞 noise reduction Dolby威 noise reduction operates only in tape mode. Dolby威 noise reduction reduces the amount of 4 hiss and static during tape playback. control to activate Press the (and deactivate) Dolby威 noise reduction. The Dolby威 noise reduction system is manufactured under license from Dolby Laboratories Licensing Corporation. Dolby威 and the double-D symbol are registered trademarks of Dolby威 Labratories Licensing Corporation.
Controls and features Setting the clock with radio data system (RDS) feature Press the RDS control until SELECT HOUR or SELECT MINS is DSP RDS displayed. Use the SEL control to manually set the time. to increase • Press hours/minutes. to decrease • Press hours/minutes. SEL Digital signal processing (if equipped) The digital signal processing (DSP) feature allows you to change the DSP RDS signal mode to suit your listening tastes.
Controls and features Use the SELECT control to change the equalization to the desired mode. SEL Radio data system (RDS) feature This feature allows your audio system to receive station DSP RDS identification or program type from RDS-equipped FM radio stations. The Federal Communications Commission (FCC) and the Canadian Radio and Telecommunications Commission (CRTC) recommend FM radio broadcasters to use RDS technology to transmit information.
Controls and features Program type • Press the RDS control until the FIND program type is displayed. RDS • Use the SEL control to select the program type. With the feature on, use the SEEK or SCAN control to find the desired program type from the following selections: • Classic • Country • Info • Jazz • Oldies • R&B • Religious • Rock • Soft • Top 40 Show • With RDS activated, press the RDS control until SHOW is displayed.
Controls and features Premium AM/FM Stereo/Single CD Radio BASS BAL SEL TREB VOL PUSH ON FADE EJ CD MUTE SCAN AM FM AUTO TUNE SEEK REW FF 1 2 3 4 RDS COMP SHUFF 5 6 Your audio system is equipped with selective lighting, a unique lighting strategy. This lighting feature is operable when the headlamps are illuminated. During the operation of any selected mode, lighting for the individual function controls will either illuminate or turn off.
Controls and features Turn the control to raise or lower volume. VOL PUSH ON If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on. Speed sensitive volume (if equipped) With this feature, radio volume changes automatically and slightly with vehicle speed to compensate for road and wind noise. The recommended level for speed sensitive volume is from level 1 through level 3.
Controls and features AM/FM select in radio mode This control allows you to select AM or FM frequency bands. Press the control to switch between AM, FM1 or FM2 memory preset stations. AM/FM select in CD or CD changer mode (if equipped) Press this control to stop CD play and begin radio play. CD select To begin CD play (if CD[s] are loaded), press the CD control. The first track of the disc will begin playing. After that, CD play will begin where it stopped last.
Controls and features Seek function The seek function control works in radio, CD and CD changer mode (if equipped). Seek function in radio mode to find the next • Press SEEK listenable station down the frequency band. to find the next listenable station up the frequency band. • Press Seek function for CD or CD changer (if equipped) to seek to the previous • Press SEEK track of the current disc.
Controls and features Setting memory preset stations 1. Select the frequency band with the AM/FM select control. 2. Select a station. Refer to Tune adjust or Seek function for more information on selecting a station. 3. Press and hold a memory preset control until the sound returns, indicating the station is held in memory on the control you selected.
Controls and features Treble adjust The treble adjust control allows you to increase or decrease the audio system’s treble output. BASS SEL TREB Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers. BAL SEL FADE Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers. BAL SEL FADE Rewind The rewind control works in CD REW mode. 1 • In CD mode, pressing the REW control for less than three seconds results in slow rewind.
Controls and features Fast forward The fast forward control works in FF CD mode. 2 • In CD mode, pressing the control for less than three seconds results in slow forward action. Pressing the control for more than three seconds results in fast forward action. Eject function Press the control to stop and eject a CD. Compression feature (if equipped) Compression adjust brings soft and loud CD passages together for a more consistent listening level.
Controls and features Radio data system (RDS) feature This feature allows your audio system to receive station RDS identification or program type from RDS-equipped FM radio station. The Federal Communications Commission (FCC) and the Canadian Radio and Telecommunications Commission (CRTC) recommend FM radio broadcasters to use RDS technology to transmit information. FM radio stations are independently operated and individually elect to use RDS technology to transmit station ID and program type as desired.
Controls and features • Use the SEL control to select the program type. With the feature on, use the SEEK or SCAN control to find the desired program type from the following selections: • Classic • Country • Info • Jazz • Oldies • R&B • Religious • Rock • Soft • Top 40 Show • With RDS activated, press the RDS control until SHOW is displayed. SEL RDS • Use the SEL control to select TYPE, NAME or NONE. SEL Mute mode Press the control to mute the playing media.
Controls and features Setting the clock Press the RDS control until SELECT HOUR or SELECT MINS is displayed. RDS Use the SEL control to manually set the time. to increase • Press hours/minutes. to decrease • Press hours/minutes. SEL Rear seat controls (if equipped) The Personal Audio System, allows front and middle seat passengers to listen to different media sources (radio, cassette or CD) simultaneously.
Controls and features To activate the Personal Audio System, press the speaker/headphone control. Press the MODE control to change audio sources (for headphone mode only). Use the SEEK, VOLUME and MEMORY controls to make adjustments to the playing media. Adjusting the volume Press the + control to increase volume. Press the - control to decrease volume.
Controls and features Using headphones/Personal Audio System Plug a 3.5 mm headphone (not included) into the jack. Press the speaker on/off control to operate the headphones. DUAL PLAY illuminates in the radio display and the fade control is disabled. The rear speakers will cut out once the speaker on/off control is pressed. The front speaker will remain playing for the front passengers. Press the control again to deactivate the headphones (Personal Audio System).
Controls and features Seek function • In radio mode, press to find the next listenable station down the frequency band. to find • In radio mode, press the next listenable station up the frequency band. • In tape mode, use the SEEK or function to access the next selection. previous • In CD mode (if equipped), use the SEEK function to access the next - VOLUME + MODE SEEK MEMORY or previous CD changer (if equipped) Your CD changer is located in the center console.
Controls and features 1. Pull the lever to remove a CD tray from the magazine. 2. Insert one disc into each CD tray of the magazine (up to 6 discs). Ensure that the label side is facing up. If you pull too hard on the disc holder, the disc holder may come completely out of the magazine. If this happens, reinsert the disc holder back into the magazine. 3. Insert each CD tray, with the disc loaded, all the way into the CD magazine. 4. Insert the CD magazine into the changer.
Controls and features 5. Slide the door to the left to close. Use only compact discs containing this mark. The magazine does not need to be full for the changer to operate. Radio power must be turned on to play the CDs in the changer. The magazine may be stored in the glove compartment when not being used. The CD magazine may be inserted or ejected with the radio power off. Keep the CD changer door closed. Coins and foreign objects will damage the CD player and void your audio system warranty.
Controls and features Cleaning compact discs Inspect all discs for contamination before playing. If necessary, clean discs only with an approved CD cleaner and wipe from the center out to the edge. Do not use circular motion. CD and CD changer care • Handle discs by their edges only. Never touch the playing surface. • Do not expose discs to direct sunlight or heat sources for extended periods of time. • Do not insert more than one disc into each slot of the CD changer magazine.
Controls and features Radio reception factors Three factors can affect radio reception: • Distance/strength.The further an FM signal travels, the weaker it is. The listenable range of the average FM station is approximately 40 km (24 miles). This range can be affected by “signal modulation.” Signal modulation is a process radio stations use to increase their strength/volume relative to other stations. • Terrain.
Controls and features Temperature control knob Controls the temperature of the airflow inside the vehicle. COOL Mode selector control Controls the direction of the airflow to the inside of the vehicle. PANEL A/C MAX A/C WARM OFF PANEL & FLOOR FLOOR FLR & DEF DEF The air conditioning compressor can operate in all modes except PANEL and FLOOR. However, the air conditioning will only function if the outside temperature is about 6°C (43°F) or higher.
Controls and features hot and full cold positions, the air distributed through the floor ducts will be slightly warmer than the air sent to the instrument panel registers. • FLOOR -Allows for maximum heating by distributing outside air through the floor ducts. However, the air will not be cooled below the outside temperature because the air conditioning does not operate in this mode. • FLR & DEF-Distributes outside air through the windshield defroster ducts and the floor ducts.
Controls and features • If your vehicle has been parked with the windows closed during warm weather conditions, the air conditioner will perform more efficiently in cooling the vehicle if driven for two or three minutes with the windows open. This will force most of the hot, stale air out of the vehicle. Once the vehicle has been “aired out”, operate the climate control system as desired. • Don’t put objects under the front seat that will interfere with the airflow to the back seats.
Controls and features Electronic Automatic Temperature Control (EATC) system (if equipped) The EATC system will maintain a selected temperature and AUTO automatically control airflow. You can override automatic operation with any of the override controls, the fan speed control or steering wheel controls (if equipped). F OUTSIDE TEMP MAX A/C Turning the EATC on Press AUTOMATIC, any of the override controls or the fan speed control. The EATC will only operate when the vehicle is running.
Controls and features windshield. In approximately 31⁄2 minutes or less, the fan speed will start to increase and the airflow location will change to the floor area. If unusual conditions exist (i.e.-window fogging, etc.), the manual override controls allow you to select airflow locations and the fan control allows you to adjust fan speed as necessary.
Controls and features Fan speed ( ) When AUTOMATIC is pressed, fan speed is adjusted automatically for existing conditions. You can override fan speed at any time. To control fan speed manually, use the thumbwheel or steering wheel control to cancel automatic fan speed operation. HI OFF AUTOMATIC FLR • DEF DEF LO • Rotate the thumbwheel up for higher fan speed or down for lower fan speed. • Press the steering wheel control up for higher fan speed or down for lower fan speed.
Controls and features • • • • • • economical and will cool the inside of the vehicle faster. Airflow is from the instrument panel registers. This mode can also be used to prevent undesirable odors from entering the vehicle. VENT-Distributes outside air through the instrument panel registers. However, the air cannot be cooled below the outside temperature because the air conditioning does not operate in this mode.
Controls and features Displaying outside temperature Press OUTSIDE TEMP to display the outside air temperature. It will be displayed until OUTSIDE TEMP is pressed again. OUTSIDE TEMP MAX A/C VENT PNL • FLR If the selected temperature is changed while the outside temperature is displayed, the new temperature will be displayed for four seconds after it is changed, then the outside temperature will return to the window.
Controls and features • Under snowy or dirty weather conditions, your vehicle’s climate control system should be left in the OFF position when the vehicle is parked. This allows the climate control system to be free from contamination of outside pollutants. • If your vehicle has been parked with the windows closed during warm weather conditions, the air conditioner will perform more efficiently in cooling the vehicle if driven for two or three minutes with the windows open.
Controls and features Auxiliary A/C-heater controls (if equipped) Depending on your equipment package, your vehicle may be equipped with auxiliary A/C-heater controls. The auxiliary A/C-heater feature provides increased capacity to quickly heat or cool the vehicle.
Controls and features In order for the auxiliary A/C-heater OFF REAR controls (if equipped) to function, the driver’s auxiliary A/C-heater HI control must be set to REAR, unless COOL WARM PANEL FLOOR your vehicle is equipped with a moonroof and a navigation system. In which case, the rear auxiliary A/C-heater control console serves as the main control for the auxiliary climate control system. LO The instrument panel climate controls must be on in order for the auxiliary A/C-heater to operate.
Controls and features POSITIONS OF THE IGNITION 1. ACCESSORY, allows the electrical 4 accessories such as the radio to 3 operate while the engine is not 5 running. 2. LOCK, locks the steering wheel, 2 automatic transmission gearshift lever and allows key removal. 1 3. OFF, shuts off the engine and all accessories without locking the steering wheel. 4. ON, all electrical circuits operational. Warning lights illuminated. Key position when driving. 5. START, cranks the engine.
Controls and features SPEED CONTROL To turn speed control on • Press ON. Vehicle speed cannot be controlled until the vehicle is traveling at or above 48 km/h (30 mph). Do not use the speed control in heavy traffic or on roads that are winding, slippery, or unpaved. ON OFF Do not shift the gearshift lever into N (Neutral) with the speed control on. To turn speed control off • Press OFF or • Turn off the vehicle ignition.
Controls and features To set a speed • Press SET ACCEL. For speed control to operate, the speed control must be ON and the vehicle speed must be greater than 48 km/h (30 mph). RES SET ACCEL COAST If you drive up or down a steep hill, your vehicle speed may vary momentarily slower or faster than the set speed. This is normal. Speed control cannot reduce the vehicle speed if it increases above the set speed on a downhill.
Controls and features To set a higher set speed • Press and hold SET ACCEL. Release the control when the desired vehicle speed is reached RES or • Press and release SET ACCEL to SET ACCEL operate the Tap-Up function. Each press will increase the set COAST speed by 1.6 km/h (1 mph) or • Accelerate with your accelerator pedal. When the desired vehicle speed is reached, press and release SET ACCEL. You can accelerate with the accelerator pedal at any time during speed control usage.
Controls and features To disengage speed control • Depress the brake pedal. Disengaging the speed control will not erase the previously programmed set speed. Pressing OFF will erase the previously programmed set speed. ON OFF To return to a previously set speed • Press RES. For RES to operate, the vehicle speed must be faster than 48 km/h (30 mph).
Controls and features Indicator light This light comes on when either the CRUISE SET ACCEL or RES controls are pressed. The vehicle speed must be at or above 48 km/h (30 mph). It turns off when the speed control OFF control is pressed, the brake or clutch is applied, or the ignition is turned to the OFF position. TILT STEERING Pull the tilt steering control toward you to move the steering wheel up or down. Hold the control while adjusting the wheel to the desired position, then release the control.
Controls and features WINDSHIELD WIPER/WASHER CONTROLS Rotate the windshield wiper control to the desired interval, low or high speed position. The bars of varying length are for intermittent wipers. When in this position rotate the control upward for fast intervals and downward for slow intervals. Push (tap) the end of the stalk briefly for a single swipe (no wash). Push and hold for three swipes with wash. Push and hold for a longer wash (up to ten seconds).
Controls and features OVERDRIVE CONTROL Activating overdrive (Overdrive) is the normal drive position for the best fuel economy. The overdrive function allows automatic upshifts and downshifts through all available gears. Deactivating overdrive Press the Transmission Control Switch (TCS) located on the end of OVERDRIVE the gearshift lever. The Transmission Control Indicator Light (TCIL) (the word OFF) will illuminate on the end of the gearshift lever.
Controls and features Forward storage bin (if equipped) Press the release control to open the storage compartment. The door will open slightly and can be moved to full open. The storage compartment may be used to secure sunglasses or a similar object. Installing a garage door opener (if equipped) The storage compartment can be converted to accommodate a variety of aftermarket garage door openers: • Place Velcro娂 hook onto back side of aftermarket transmitter opposite of actuator control.
Controls and features One-touch moon roof (if equipped) With trip computer VENT ROOF VENT Without trip computer AUTO ROOF • Press and release the rear portion of the moon roof control to open. • Press and hold (as desired) the front portion of the moon roof control to close. • To halt motion at any point during one-touch opening, press the control a second time. • The moon roof has a sliding shade that can be manually opened or closed when the glass panel is shut.
Controls and features Trip computer For information on the trip computer, refer to Trip computer in the Instrumentation chapter. Electronic compass (if equipped) The compass reading may be affected when you drive near large buildings, bridges, power lines and powerful broadcast antennas. Magnetic or metallic objects placed in, on or near the vehicle may also affect compass accuracy.
Controls and features Compass zone adjustment 1. Determine which magnetic zone you are in for your geographic location by referring to the zone map. 1 15 2 14 3 13 4 12 11 5 6 10 7 8 9 With trip computer 2. Locate the compass module mounted on the center rear view mirror post. 3. Turn ignition to the ON position. 4. Press and hold the RESET button on top of the compass module until the message display in the trip computer shows the current zone setting. 5. Release the RESET button. 6.
Controls and features Without trip computer 1. Press and hold the SELECT control until VAR appears in the display, then release. The display should show the current zone number. 2. Press the SELECT control until the desired zone number appears. The display will flash and then return to normal operation. The zone is now updated. AUTO ROOF CAL Compass calibration adjustment Perform this adjustment in an open area free from steel structures and high voltage lines.
Controls and features Without trip computer 1. Press and hold the SELECT control until CAL appears in the display (approximately eight seconds) and release. 2. Drive the vehicle slowly (less than 5 km/h [3 mph]) in circles until CAL indicator turns off in about 2–3 complete circles. 3. The compass is now calibrated.
Controls and features Press the portion of the VENT control to open the power rear quarter windows. portion of the VENT control to close the power rear Press the quarter windows. Interior Lamps Map lamps With trip computer VENT ROOF VENT Without trip computer AUTO ROOF To turn on the map lamps, press the control next to each lamp.
Controls and features Rear dome lamp The dome lamp lights when: • any door is opened. • the instrument panel dimmer switch is held up until the courtesy lamps come on. • any of the remote entry controls are pressed and the ignition is OFF. With the ignition key in the ACC or ON position, the rear dome lamp can be turned ON or OFF by sliding the control. AUTOMATIC DIMMING REAR VIEW MIRRORS (IF EQUIPPED) Your vehicle is equipped with an inside rear view mirror with an auto-dimming function.
Controls and features HOMELINK姞 UNIVERSAL TRANSCEIVER (IF EQUIPPED) The HomeLink威 Universal Transceiver, located on the driver’s visor, provides a convenient way to replace up to three hand-held transmitters with a single built-in device. This feature will learn the radio frequency codes of most current transmitters to operate garage doors, entry gates, security systems, entry door locks, and home or office lighting.
Controls and features 3. Using both hands simultaneously press and hold the hand-held transmitter button and the desired HomeLink威 button. Do not release the buttons until step 4 has been completed. Some entry gates and garage door openers may require you to replace step 3 with the procedure in the “Canadian Programing” section. 4. The red light will flash slowly and then rapidly. Release both buttons when the red light flashes rapidly. 5. Follow steps 2 through 4 to program the remaining two buttons.
Controls and features Operating the HomeLink姞 Universal Transceiver Once programmed, the HomeLink威 Universal Transceiver can be used in place of hand-held transmitters. To operate, simply press and release the appropriate HomeLink威 button (the red light will illuminate, indicating the signal is being transmitted).
Controls and features 3. Press and release the programmed HomeLink威 button. Press and release the HomeLink威 button a second time to complete the training process. (Some garage door openers may require this procedure to be done a third time to complete the training). The 2nd or 3rd press from step 3 will activate the door. The HomeLink威 Universal Transceiver has now been trained to the receiver. The remaining two buttons may now be programmed if this has not previously been done.
Controls and features POWER WINDOWS Press and hold the rocker switches to open and close windows. • Press the top portion of the rocker switch to close. AUTO • Press the bottom portion of the rocker switch to open. AUTO One touch down • Press AUTO completely down and release quickly. The driver’s window will open fully. Depress again to stop window operation. One touch down can be deactivated during operation by pushing down on the top part of the driver power window control.
Controls and features Window lock The window lock feature allows only the driver to operate the power windows. To lock out all the window controls WINDOW LOCK except for the driver’s press the left side of the control. Press the right side to restore the window controls. Accessory delay With accessory delay, the window switches may be used for up to ten minutes after the ignition switch is turned to the OFF position or until any door is opened.
Controls and features POWER SIDE VIEW MIRRORS The ignition can be in any position to adjust the power side view mirrors. To adjust your mirrors: 1. Select L to adjust the left mirror or R to adjust the right mirror. MIRRORS L 2. Move the control in the direction you wish to tilt the mirror. MIRRORS L R 3. Return to the center position to lock mirrors in place. 4. Adjust spotter mirrors (if equipped) manually.
Controls and features Signal mirrors (if equipped) When the turn signal is activated, the outer portion of the appropriate mirror housing will blink red. This provides an additional warning to other drivers that your vehicle is about to turn. Fold-away mirrors Pull the side mirrors in carefully when driving through a narrow space, like an automatic car wash. CENTER CONSOLE Your vehicle may be equipped with a variety of console features.
Controls and features POSITIVE RETENTION FLOOR MAT (IF EQUIPPED) Position the floor mat so that the eyelet is over the pointed end of the retention post and rotate forward to lock in. Make sure that the mat does not interfere with the operation of the accelerator or the brake pedal. To remove the floor mat, reverse the installation procedure. LIFTGATE To open the rear window, turn the liftgate handle to the right. To open the liftgate, turn the liftgate handle to the left.
Controls and features SECURILOCK姟 PASSIVE ANTI-THEFT SYSTEM SecuriLock娂 passive anti-theft system is an engine immobilization system. This system prevents the engine from being started unless a coded key programmed to your vehicle is used. The SecuriLock娂 passive anti-theft system is not compatible with non-Ford aftermarket remote start systems. Use of these systems may result in vehicle starting problems and a loss of security protection.
Controls and features Large metallic objects, electronic devices on the key chain that can be used to purchase gasoline or similar items, or a second key on the same key ring as the coded key may cause vehicle starting issues. If present, you need to keep these objects from touching the coded key while starting the engine. These objects and devices cannot damage the coded key, but can cause a NO—START condition if they are too close to the key during engine start.
Controls and features Programming spare keys A maximum of eight keys can be coded to your vehicle. Only SecuriLock娂 keys can be used. To program a coded key yourself, you will need two previously programmed coded keys (keys that already operate your vehicle’s engine) and the new unprogrammed key(s) readily accessible for timely implementation of each step in the procedure.
Controls and features REMOTE ENTRY SYSTEM This device complies with part 15 of the FCC rules and with RS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Controls and features Locking the doors Press this control to lock all doors. The doors will lock and the lamps will flash. To confirm doors are closed and locked, press this control a second time within three seconds. The door(s) will lock again, the horn will chirp once and the lamps will flash. If any of the doors are open or ajar, the horn will make two quick chirps, reminding you to properly close the doors. Sounding a panic alarm Press this control to activate the alarm.
Controls and features To replace the battery: 1. Twist a thin coin between the two halves of the transmitter near the key ring. DO NOT TAKE THE FRONT PART OF THE TRANSMITTER APART. 2. Place the positive (+) side of new battery in the same orientation. Refer to the diagram inside the transmitter unit. 3. Snap the two halves back together. Replacement of the battery will not cause the remote transmitter to become deprogrammed from your vehicle.
Controls and features Programming remote transmitters It is necessary to have all (maximum of four — original and/or new) of your remote transmitters available prior to beginning this procedure. To program the transmitters yourself: • Place the key in the ignition and turn from 2 (LOCK) to 3 (OFF) 4 and cycle between 3 (OFF) and 3 4(ON) eight times in rapid 5 succession (within 10 seconds) with the eighth turn ending in the 2 4 (ON) position.
Controls and features The battery save feature will turn off the interior lights 45 minutes after the last door is closed, even if the dimmer control is on. Memory seat/mirrors/adjustable pedal feature (if equipped) The memory feature allows automatic positioning of the driver seat, side mirrors and adjustable pedals to three programmable positions. • To program position one, move the driver seat, both side mirrors, and adjustable pedals to the desired positions. Press the SET control.
Controls and features 7. Turn ignition to OFF. The horn will chirp once to confirm the procedure is complete. Autolock (if equipped) This feature automatically locks all vehicle doors when: • all doors, liftgate and liftgate window are closed • the engine is running • you shift into any gear putting the vehicle in motion. Relock The autolock feature repeats when: • any door, except the drivers, is opened then closed while the engine is running and • you put the vehicle in motion.
Controls and features 2. Press 1/2 control within five seconds of step 1. 1 2 3 4 5 6 7 8 9 0 3. Enter your personal 5 digit code. Enter each digit within five seconds of previous one. Do not set a code that includes five of the same number or presents them in sequential order. Thieves can easily figure out these types of codes. Your personal code does not replace the permanent code that the dealership gave you. You can use either code to unlock your vehicle.
Controls and features Locking the doors with the keyless entry system It is not necessary to enter the factory or personal code prior to locking all doors. To lock the doors: • Press the 7/8 control and the 9/0 control at the same time. Activating/deactivating autolock with the keyless entry system Before following the activation or deactivation procedures, make sure that the anti-theft system (if equipped) is not armed, ignition is off, and all vehicle doors and liftgate window are closed. 1.
Seating and safety restraints SEATING Adjustable head restraints (if equipped) Your vehicle’s seats may be equipped with head restraints which are vertically adjustable. The purpose of these head restraints is to help limit head motion in the event of a rear collision. To properly adjust your head restraints, lift the head restraint so that it is located directly behind your head or as close to that position as possible. Refer to the following to raise and lower the head restraints.
Seating and safety restraints Lift handle to move seat forward or backward. Pull lever up to adjust seatback. 60/40 split bench seat (if equipped) • Lift the release bar to move the seat forward or backward. Ensure the seat is relatched into place. • Pull the seatback handle up to recline the seat.
Seating and safety restraints Using the armrest (if equipped) Push the release control to move the armrest up or down. Using the manual lumbar support Turn the lumbar support control toward the front of vehicle to move the lumbar support forward for more direct support. Turn the lumbar support control toward the rear of vehicle to move the lumbar support back for less direct support. Adjusting the front power seat (if equipped) Never adjust the driver’s seat or seatback when the vehicle is moving.
Seating and safety restraints Reclining the seatback can reduce the effectiveness of the seat’s safety belt in the event of a collision. The control is located on the outboard side of the seat cushion. Press to raise or lower the front portion of the seat cushion. Press to raise or lower the rear portion of the seat cushion. Press the control to move the seat forward, backward, up or down.
Seating and safety restraints Memory seats/rearview mirrors/adjustable pedals (if equipped) This system allows automatic positioning of the driver seat, outside rearview mirrors, and SET adjustable pedals to three programmable positions. The memory seat control is located on the driver door. 1 2 • To program position one, move the driver seat to the desired position using the seat controls. Press the SET control. The SET control indicator light will briefly illuminate.
Seating and safety restraints REAR SEATS Adjustable head restraints Your vehicle’s seats may be equipped with head restraints which are vertically adjustable. The purpose of these head restraints is to help limit head motion in the event of a rear collision. To properly adjust your head restraints, lift the head restraint so that it is located directly behind your head or as close to that position as possible. Refer to the following to raise and lower the head restraints.
Seating and safety restraints 3. Press the green control on the seatback to release the closeout panel. Rotate the panel to closeout the space in the floor. 4. Once the second row seats are in the down position, the front seats may be readjusted. Returning the seat to upright Always latch the vehicle seat to the floor, whether the seat is occupied or empty. If not latched, the seat may cause injury during a sudden stop. 1.
Seating and safety restraints Reclining the seatback Locate the lever at the bottom of the seatback that reads “FOLD FLAT OR RECLINE”. Pull the lever upwards to recline the seatback. Third row seat The third row seat is equipped with combination lap and shoulder belts in the outboard seating positions and a manual adjust tongue lap belt in the center seating position. For information on the proper operation of the safety restraints, refer to Safety Restraints in this chapter.
Seating and safety restraints Ensure that the second row seat is in the upright position in order to achieve optimum access to the third row. To minimize the risk of personal injury, the third row seat should not be left in the forward, stowed position while the vehicle is in motion. Please ensure that the seat is in the upright, fully latched position before putting the vehicle in motion. 1. Locate and lift seat control “3RD ROW ENTRY” to release seatback and cushion to flip toward the front seat. 2.
Seating and safety restraints 2. Before removing the seat, be sure that the detachable anchor tongue is stowed flat into the vehicle floor. 3. Use the black plastic clip (located just above the detachable anchor) to stow the loose seat belt. • Pull the seat release lever located on the lower right side of the seatback while pushing the seatback down into the seat cushion. • The seatback will latch into place. 4.
Seating and safety restraints Installing the third row seat Always latch the vehicle seat to the floor, whether the seat is occupied or empty. If not latched, the seat may cause injury during a sudden stop. When reinstalling a rear seat in your vehicle it must be placed in its original position. Improper installation of the seat will prevent correct use of the safety belts and could increase the risk of injury. Refer to the warning label on the seat belt.
Seating and safety restraints 3rd row tip/stow feature The 3rd row seat has a tip/stow feature to increase cargo space without removing the seat from the vehicle. To put seat in tip/stow position: 1. Pull the seat release lever located on the lower right side of the seatback while pushing the seatback down into the seat cushion. 2. The seatback will latch into place. 3.
Seating and safety restraints 6. Pull down support bar and push into floor latch. To return seat to seating position: 1. Hold seat and pull support bar from floor latch. 2. Rotate support bar up under seat. 3. Rotate floor latch down into floor tub. 4. Lower the seat. When the rear of the seat is 10–13 cm (4–5 in) above the rear pins, let the seat drop. This will ensure that the seat will properly latch into the floor.
Seating and safety restraints It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts. Be sure everyone in your vehicle is in a seat and using a safety belt properly. In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a safety belt.
Seating and safety restraints • Rear seats (if equipped) 2. To unfasten, push the release button and remove the tongue from the buckle.
Seating and safety restraints The front and rear outboard safety restraints in the vehicle are combination lap and shoulder belts. The front passenger and rear seat outboard safety belts have two types of locking modes described below: Vehicle sensitive mode The vehicle sensitive mode is the normal retractor mode, allowing free shoulder belt length adjustment to your movements and locking in response to vehicle movement.
Seating and safety restraints • Rear seats (if equipped) 2. Grasp the shoulder portion and pull downward until the entire belt is extracted. 3. Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the automatic locking mode. How to disengage the automatic locking mode Ford recommends that all safety belt assemblies and attaching hardware should be inspected by a qualified technician after any collision.
Seating and safety restraints Disconnect the combination lap/shoulder belt and allow it to retract completely to disengage the automatic locking mode and activate the vehicle sensitive (emergency) locking mode. After any vehicle collision, the front passenger outboard seat belt system must be checked by a qualified technician to verify that the “automatic locking retractor” feature for child seats is still functioning properly. In addition, all seat belts should be checked for proper function.
Seating and safety restraints Lap belts Adjusting the lap belt The lap belt should fit snugly and as low as possible around the hips, not across the waist. • 1st row and 3rd row (if equipped) center seating positions The lap belt does not adjust automatically. Insert the tongue into the correct buckle (the buckle closest to the direction the tongue is coming from). To lengthen the belt, turn the tongue at a right angle to the belt and pull across your lap until it reaches the buckle.
Seating and safety restraints Front and second row safety belt height adjustment Your vehicle has safety belt height adjustments for the driver, front passenger and second row passengers. Adjust the height of the shoulder belt so the belt rests across the middle of your shoulder. To lower the shoulder belt height, push the button down and slide the height adjuster down. To raise the height of the shoulder belt, slide the height adjuster up.
Seating and safety restraints Conditions of operation If... The driver’s safety belt is not buckled before the ignition switch is turned to the ON position... Then... The safety belt warning light illuminates 1-2 minutes and the warning chime sounds 4-8 seconds. The safety belt warning light and warning chime turn off. The driver’s safety belt is buckled while the indicator light is illuminated and the warning chime is sounding...
Seating and safety restraints The following are reasons most often given for not wearing safety belts: (All statistics based on U.S. data) Reasons given... “Crashes are rare events” Consider... 36 700 crashes occur every day. The more we drive, the more we are exposed to “rare” events, even for good drivers. 1 in 4 of us will be seriously injured in a crash during our lifetime. “I’m not going far” 3 of 4 fatal crashes occur within 25 miles of home.
Seating and safety restraints Do not sit on top of a buckled safety belt to avoid the Belt Minder chime. Sitting on the safety belt will increase the risk of injury in an accident. To disable (one-time) or deactivate the Belt Minder feature please follow the directions stated below. One time disable Any time the safety belt is buckled and then unbuckled during an ignition ON cycle, Belt Minder will be disabled for that ignition cycle only.
Seating and safety restraints 4. Turn on the parklamps/headlamps, turn off the parklamps/headlamps. 5. Buckle then unbuckle the safety belt three times, ending with the safety belt unbuckled. • After step 5 the safety belt warning light will be turned on for three seconds. 6. Within seven seconds of the safety belt warning light turning off, buckle then unbuckle the safety belt. • This will disable Belt Minder if it is currently enabled, or enable Belt Minder if it is currently disabled. 7.
Seating and safety restraints Failure to inspect and if necessary replace the safety belt assembly under the above conditions could result in severe personal injuries in the event of a collision. Refer to Cleaning and maintaining the safety belts in the Maintenacne and Care section.
Seating and safety restraints Important supplemental restraint system (SRS) precautions The supplemental restraint system is designed to work with the safety belt to help protect the driver and right front passenger from certain upper body injuries. Air bags DO NOT inflate slowly or gently and the risk of injury from a deploying air bag is greatest close to the trim covering the air bag module.
Seating and safety restraints Do not put anything on or over the air bag module. Placing objects on or over the air bag inflation area may cause those objects to be propelled by the air bag into your face and torso causing serious injury. Do not attempt to service, repair, or modify the Air Bag Supplemental Restraint System or its fuses. See your Ford or Lincoln Mercury dealer.
Seating and safety restraints Children and air bags For additional important safety information, read all information on safety restraints in this guide. Children must always be properly restrained. Accident statistics suggest that children are safer when properly restrained in the rear seating positions than in the front seating position. Failure to follow these instructions may increase the risk of injury in a collision. Air bags can kill or injure a child in a child seat.
Seating and safety restraints The air bags inflate and deflate rapidly upon activation. After air bag deployment, it is normal to notice a smoke-like, powdery residue or smell the burnt propellant. This may consist of cornstarch, talcum powder (to lubricate the bag) or sodium compounds (e.g., baking soda) that result from the combustion process that inflates the air bag. Small amounts of sodium hydroxide may be present which may irritate the skin and eyes, but none of the residue is toxic.
Seating and safety restraints The RCM (restraints control module) monitors its own internal circuits and the supplemental air bag electrical system warning (including the impact sensors, the system wiring, the air bag system readiness light, the air bag back up power and the air bag ignitors). Determining if the system is operational The SRS uses a readiness light in the instrument cluster or a tone to indicate the condition of the system.
Seating and safety restraints SIDE AIR BAG SYSTEM (IF EQUIPPED) Do not place objects or mount equipment on or near the air bag cover on the side of the seatbacks of the front seats or in front seat areas that may come into contact with a deploying air bag. Failure to follow these instructions may increase the risk of personal injury in the event of a collision. Do not use accessory seat covers.
Seating and safety restraints How does the side air bag system work? The side air bag system consists of the following: • An inflatable nylon bag (air bag) with a gas generator concealed behind the outboard bolster of the driver and front passenger seatbacks. • A special seat cover designed to allow airbag deployment. • The same warning light, electronic control and diagnostic unit as used for the front air bags. • Two crash sensors located under the outboard side of the front seats, attached to the floor.
Seating and safety restraints Several air bag system components get hot after inflation. Do not touch them after inflation. If the side air bag has deployed, the air bag will not function again. The side air bag system (including the seat) must be inspected and serviced by a qualified technician in accordance with the vehicle service manual. If the air bag is not replaced, the unrepaired area will increase the risk of injury in a collision.
Seating and safety restraints Disposal of air bags and air bag equipped vehicles For disposal of air bags or air bag equipped vehicles, see your local dealership or qualified technician. Air bags MUST BE disposed of by qualified personnel. SAFETY RESTRAINTS FOR CHILDREN See the following sections for directions on how to properly use safety restraints for children. Also see Air Bag Supplemental Restraint System (SRS) in this chapter for special instructions about using air bags.
Seating and safety restraints Do not leave children, unreliable adults, or pets unattended in your vehicle. To improve the fit of lap and shoulder belts on children who have outgrown child safety seats, Ford recommends use of a belt-positioning booster seat that is labelled as conforming to all applicable Federal motor vehicle safety standards.
Seating and safety restraints When installing a child safety seat: • Review and follow the information presented in the Air Bag Supplemental Restraint System (SRS) section in this chapter. • Use the correct safety belt buckle for that seating position (the buckle closest to the direction the tongue is coming from). • Insert the belt tongue into the proper buckle until you hear a snap and feel it latch. Make sure the tongue is securely fastened in the buckle.
Seating and safety restraints Installing child safety seats in combination lap and shoulder belt seating positions Air bags can kill or injure a child in a child seat. NEVER place a rear-facing child seat in front of an active air bag. If you must use a forward-facing child seat in the front seat, move the seat all the way back. 1. Position the child safety seat in a seat with a combination lap and shoulder belt. Children 12 and under should be properly restrained in the rear seat whenever possible. 2.
Seating and safety restraints 3. While holding the shoulder and lap belt portions together, route the tongue through the child seat according to the child seat manufacturer’s instructions. Be sure the belt webbing is not twisted. 4. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) for that seating position until you hear a snap and feel the latch engage. Make sure the tongue is latched securely by pulling on it. 5.
Seating and safety restraints 7. Pull the lap belt portion across the child seat toward the buckle and pull up on the shoulder belt while pushing down with your knee on the child seat. 8. Allow the safety belt to retract to remove any slack in the belt. 9. Before placing the child in the seat, forcibly tilt the seat forward and back to make sure the seat is securely held in place. 10.
Seating and safety restraints 5. If you have not pulled out enough webbing to reach, allow the webbing to fully retract before attempting to pull it out again and repeat steps 2 through 4. 6. Pull the webbing through the child seat toward the buckle while pushing down with your knee on the child seat. 7. Allow the safety belt to retract to remove any slack in the belt. It will make a clicking noise while doing this. 8.
Seating and safety restraints Tether anchorage hardware All second row and one third row seating position have a fabric strap installed near the bottom of the rear face of the seatback. These straps have a loop at the top, and are to be used for child seat tether anchorages. A tethered seat can be installed in the front passenger seat. Put the tether strap over the seatback and attach it to an anchor bracket. Anchor brackets can be bolted to the rear edge of the front passenger seat cushion.
Seating and safety restraints The tether strap anchors in your vehicle are in the following positions (shown from top view): Attach the tether strap only to the appropriate tether anchor as shown. The tether strap may not work properly if attached somewhere other than the correct tether anchor. 1. Position the child safety seat on the seat cushion. 2. Route the child safety seat tether strap over the back of the seat. 3. Locate the correct anchor for the selected seating position.
Seating and safety restraints • You may need to pull the seatback forward to access the tether anchors. Make sure the seat is locked in the upright position before installing the child seat. Refer to the Folding Down The Rear Seats section in this chapter for information on how to operate the rear seats. 4. Clip the tether strap to the anchor as shown. If the tether strap is clipped incorrectly, the child safety seat may not be retained properly in the event of a collision. 5.
Starting PREPARING TO START YOUR VEHICLE Engine starting is controlled by the powertrain control system. This system meets all Canadian Interference-Causing Equipment standard requirements regulating the impulse electrical field strength of radio noise. When starting a fuel-injected engine, avoid pressing the accelerator before or during starting. Only use the accelerator when you have difficulty starting the engine. For more information on starting the vehicle, refer to Starting the engine in this chapter.
Starting Important safety precautions A computer system controls the engine’s idle revolutions per minute (RPM). When the engine starts, the idle RPM runs faster to warm the engine. If the engine idle speed does not slow down automatically, have the vehicle checked. Do not allow the vehicle to idle for more than 10 minutes at the higher engine RPM. Before starting the vehicle: 1. Make sure all vehicle occupants have buckled their safety belts.
Starting 5. Turn the key to 4 (ON) without turning the key to 5 (START). 4 If there is difficulty in turning the 3 key, firmly rotate the steering wheel 5 left and right until the key turns freely. This condition may occur 2 when: • front wheels are turned 1 • front wheel is against the curb • steering wheel is turned when getting in or out of the vehicle Make sure the corresponding lights illuminate or illuminate briefly. If a light fails to illuminate, have the vehicle serviced. light may not illuminate.
Starting 3. If the temperature is below -12° C (10° F) and the engine does not start in 15 seconds on the first try, turn the key OFF and wait 10 seconds and try again. If the engine does not start in two attempts, press the accelerator pedal all the way to floor and hold. Turn the key to START position. 4. When the engine starts, release the key, then release the accelerator pedal gradually as the engine speeds up. 5. After idling for a few seconds, apply the brake and release the parking brake.
Starting WARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. In addition, certain fluids contained in vehicles and certain products of component wear contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
Driving BRAKES Your service brakes are self-adjusting. Refer to the scheduled maintenance guide for scheduled maintenance. Occasional brake noise is normal and often does not indicate a performance concern with the vehicle’s brake system. In normal operation, automotive brake systems may emit occasional or intermittent squeal or groan noises when the brakes are applied.
Driving ABS warning lamp ABS The ABS warning lamp in the instrument cluster momentarily illuminates when the ignition is turned to the ON position. If the light does not illuminate momentarily at start up, remains on or continues to flash, the ABS needs to be serviced. With the ABS light on, the anti-lock brake system is disabled and normal BRAKE braking is still effective unless the ! brake warning light also remains illuminated with parking brake released.
Driving Parking brake Apply the parking brake whenever the vehicle is parked. To set the parking brake, press the parking brake pedal down until the pedal stops. HOOD BRAKE The BRAKE warning lamp in the instrument cluster illuminates and remains illuminated (when the ignition is turned ON) until the parking brake is released. BRAKE ! Always set the parking brake fully and make sure that the gearshift is securely latched in P (Park). The parking brake is not recommended to stop a moving vehicle.
Driving Pull the release lever to release the brake. Driving with the parking brake on will cause the brakes to wear out quickly and reduce fuel economy. HOOD BRAKE STEERING Your vehicle is equipped with power steering. Power steering uses energy from the engine to help steer the vehicle. To prevent damage to the power steering pump: • Never hold the steering wheel to the extreme right or the extreme left for more than a few seconds when the engine is running.
Driving Speed sensitive steering The steering in your vehicle is speed sensitive. At high speeds, steering assist will decrease to improve steering feel. If the amount of effort required to steer your vehicle changes while driving at a constant vehicle speed, have the power steering system checked by your dealer or a qualified service technician.
Driving The air suspension shut-off switch is located behind an access panel underneath the passenger side instrument panel. On vehicles equipped with Air Suspension, turn OFF the Air Suspension switch prior to jacking, hoisting or towing your vehicle. OFF Normal vehicle operation does not require any action by the driver.
Driving To avoid injury, never run the engine with one wheel off the ground, such as when changing a tire. PREPARING TO DRIVE YOUR VEHICLE Utility vehicles have a significantly higher rollover rate than other types of vehicles. In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt. Your vehicle has special design and equipment features to make it capable of performing in a wide variety of circumstances.
Driving AUTOMATIC TRANSMISSION OPERATION Brake-shift interlock This vehicle is equipped with a brake-shift interlock feature that prevents the gearshift lever from being moved from P (Park) when the ignition is in the ON position unless brake pedal is depressed. If you cannot move the gearshift lever out of P (Park) with ignition in the ON position and the brake pedal depressed: 1. Apply the parking brake, turn ignition key to LOCK, then remove the key. 2. Insert the key and turn it to OFF.
Driving Driving with a 4–speed automatic transmission Your vehicle’s automatic transmission is equipped with a special shift strategy that insures maximum heater performance during cold weather operation. When ambient temperature is –5° C (23° F) or below and the engine coolant temperature is below 38° C (100° F), light throttle upshifts may be slightly delayed. Once the engine coolant temperature reaches 71° C (160° F) the normal shift strategy will resume.
Driving R (Reverse) With the gearshift lever in R (Reverse), the vehicle will move backward. Always come to a complete stop before shifting into and out of R (Reverse). N (Neutral) With the gearshift lever in N (Neutral), the vehicle can be started and is free to roll. Hold the brake pedal down while in this gear. (Overdrive) The normal driving position for the best fuel economy. Transmission operates in gears one through four.
Driving Each time the vehicle is started, the transmission will automatically return to normal overdrive mode. Every time the vehicle is shut off and restarted, you must press the transmission control switch to cancel overdrive operation if driving in overdrive is not desired. 2 (Second) Use 2 (Second) to start-up on slippery roads or to provide additional engine braking on downgrades. 1 (First) Use 1 (Low) to provide maximum engine braking on steep downgrades.
Driving FOUR-WHEEL DRIVE (4WD) OPERATION (IF EQUIPPED) For important information regarding safe operation of this type of vehicle, see Preparing to drive your vehicle in this chapter. When Four–wheel drive (4WD) is engaged, power is supplied to all four wheels through a transfer case. 4WD power can be selected when additional driving power is desired.
Driving Positions of the Control-Trac system The Control-Trac A4WD system 4H functions in three modes: A4WD 4L • A4WD position delivers power to the rear axle. If the rear wheels lose traction, power will be automatically delivered to the front axle to maintain traction throughout the slippery condition. • 4H position provides mechanically locked four-wheel drive power delivery to front and rear axles.
Driving Shifting from 4H to 4L (and 4L to 4H) 1. Bring the vehicle to a stop. 2. Depress the brake. 3. Place the gearshift in N (Neutral). 4. Move the 4WD control to the 4H (or 4L) position. Shifting to A4WD Move the 4WD control back to A4WD at a stop or at speeds up to 88 km/h (55 mph).
Driving If your vehicle gets stuck If the vehicle is stuck in mud or snow it may be rocked out by shifting from forward and reverse gears, stopping between shifts, in a steady pattern. Press lightly on the accelerator in each gear. Do not rock the vehicle if the engine is not at normal operating temperature or damage to the transmission may occur. Do not rock the vehicle for more than a few minutes or damage to the transmission and tires may occur or the engine may overheat.
Driving synthetic lubricant and does not normally require a lubricant change for the life of the vehicle. Rear axle lubricant quantities should not need to be checked unless a leak is suspected. Driving on hilly or sloping terrain When driving on a hill, avoid driving crosswise or turning on steep slopes. You could lose traction and slip sideways. Drive straight up, straight down or avoid the hill completely. Know the conditions on the other side of a hill before driving over the crest.
Driving DRIVING THROUGH WATER Do not drive quickly through standing water, especially if the depth is unknown. Traction or brake capability may be limited and if the ignition system gets wet, your engine may stall. Water may also enter your engine’s air intake and severely damage your engine. If driving through deep or standing water is unavoidable, proceed very slowly. Never drive through water that is higher than the bottom of the hubs (for trucks) or the bottom of the wheel rims (for cars).
Driving • GCWR (Gross Combined Weight Rating): Maximum combined weight of towing vehicle (including passengers and cargo) and the trailer. The GCWR indicates the maximum loaded weight that the vehicle is designed to tow. • Maximum Trailer Weight Rating: Maximum weight of a trailer the vehicle is permitted to tow.
Driving Special loading instructions for owners of pickup trucks and utility-type vehicles For important information regarding safe operation of this type of vehicle, see the Preparing to drive your vehicle section inthe Driving chapter of this owner guide. Loaded vehicles, with a higher center of gravity, may handle differently than unloaded vehicles. Extra precautions, such as slower speeds and increased stopping distance, should be taken when driving a heavily loaded vehicle.
Driving TRAILER TOWING Trailer towing with your vehicle may require the use of a trailer tow option package. Trailer towing puts additional loads on your vehicle’s engine, transmission, axle, brakes, tires, and suspension. For your safety and to maximize vehicle performance, be sure to use the proper equipment while towing. Follow these guidelines to ensure safe towing procedure: • Stay within your vehicle’s load limits.
Driving Engine Rear axle ratio Tire size cm (inches) Maximum GCWR - kg (lbs.) 4x2 4.6L 3.31 40.6 (16) 4 990 (11 000) 4.6L 3.31 40.6 (17) 4 990 (11 000) 5.4L 3.31 40.6 (16) 5 443 (12 000) 5.4L 3.55 40.6 (16) 5 897 (13 000) 5.4L 3.55 43.2 (17) 5 897 (13 000) 5.4L 3.73 40.6 (16) 6 123 (13 500) 5.4L 3.73 43.2 (17) 6 124 (13 500) Trailer weight range (0 - maximum) kg (lbs.
Driving Towing trailers beyond the maximum recommended gross trailer weight exceeds the limit of the vehicle and could result in engine damage, transmission damage, structural damage, loss of control and personal injury. Preparing to tow Use the proper equipment for towing a trailer, and make sure it is properly attached to your vehicle. See your dealer or a reliable trailer dealer if you require assistance.
Driving Adjusting an equalizing hitch so the rear bumper of the vehicle is lower or higher than it was unloaded will defeat the function of the load equalizing hitch and may cause unpredictable handling. Safety chains Always connect the trailer’s safety chains to the frame or hook retainers of the vehicle hitch. To connect the trailer’s safety chains, cross the chains under the trailer tongue and allow slack for turning corners.
Driving Driving while you tow When towing a trailer: • Ensure that you turn off your speed control. The speed control may shut off automatically when you are towing on long, steep grades. • Consult your local motor vehicle speed regulations for towing a trailer. • Use a lower gear when towing up or down steep hills. This will eliminate excessive downshifting and upshifting for optimum fuel economy and transmission cooling. • Anticipate stops and brake gradually.
Driving 4WD vehicles electronic shift transfer case (with automatic transmissions) 4x4 vehicles with electronic shift on the fly cannot be towed with any wheels on the ground. Trailer towing tips • Practice turning, stopping and backing up before starting on a trip to get the feel of the vehicle trailer combination. When turning, make wider turns so the trailer wheels will clear curbs and other obstacles. • Allow more distance for stopping with a trailer attached.
Driving LUGGAGE RACK (IF EQUIPPED) The rear cross-bar can be adjusted to fit the item being carried. The front cross-bar does not move. To adjust the luggage rack, push the adjustment lever forward (toward the front of the vehicle), then slide the cross-bar forward and lock the adjusting levers by pushing them down (toward the back of the vehicle). Pull the cross-bar rearward to ensure that it is locked in place. Load luggage at the front cross-bar and adjust the rearcross-bar as necessary.
Roadside emergencies GETTING ROADSIDE ASSISTANCE To fully assist you should you have a vehicle concern, Ford offers a complimentary roadside assistance program. This program is separate from the New Vehicle Limited Warranty. The service is available: • 24–hours, seven days a week • for the Basic warranty period (Canada) or New Vehicle Limited Warranty period (U.S.
Roadside emergencies Roadside coverage beyond basic warranty In the United States, you may purchase additional roadside assistance coverage beyond this period through the Ford Auto Club by contacting your Ford or Lincoln Mercury dealer. Similarly in Canada, for uninterrupted Roadside Assistance coverage, you may purchase extended coverage prior to your Basic Warranty’s Roadside Assistance expiring. For more information and enrollment, contact 1–877–294–2582 or visit our website at www.ford.ca.
Roadside emergencies The fuel pump shut-off switch is located in the passenger’s foot well, by the kick panel. Use the following procedure to reset the fuel pump shut-off switch. 1. Turn the ignition to the OFF position. 2. Check the fuel system for leaks. 3. If no fuel leak is apparent, reset the fuel pump shut-off switch by pushing in on the reset button. 4. Turn the ignition to the ON position. Pause for a few seconds and return the key to the OFF position. 5.
Roadside emergencies FUSES AND RELAYS Fuses If electrical components in the vehicle are not working, a fuse may have blown. Blown fuses are identified by a broken wire within 15 the fuse. Check the appropriate fuses before replacing any electrical components. NOTE: Always replace a fuse with one that has the specified amperage rating. Using a fuse with a higher amperage rating can cause severe wire damage and could start a fire.
Roadside emergencies 20 21 10 11 31 30 9 RELAY 5 29 19 8 28 18 7 RELAY 4 RELAY 3 RELAY 2 RELAY 1 6 17 27 26 16 5 25 15 4 24 14 3 13 2 23 12 FUSE1 22 Passenger compartment fuse panel The fuse panel is located below and to the left of the steering wheel by the brake pedal. Remove the panel cover to access the fuses. To remove a fuse use the fuse puller tool provided on the fuse panel cover. The fuses are coded as follows.
Roadside emergencies Fuse/Relay Location 4 Fuse Amp Rating 7.
Roadside emergencies Fuse/Relay Location 16 Fuse Amp Rating 20A 17 10A 18 5A 19 20 — 5A 21 15A 22 10A 23 10A 24 10A 25 26 27 28 29 — 10A 5A 10A 5A 30 30A 31 10A 184 Passenger Compartment Fuse Panel Description Headlamps (Hi Beams), Cluster (Hi Beam Indicator) Heated Mirrors, Heated Grid Switch Indicator Instrument Illumination (Dimmer Switch Power) Not Used Audio, Air Suspension Module, GEM Module, Memory Module Starter Relay, Fuse 20, Transmission Range Switch Air Bag Module, Intelli
Roadside emergencies Fuse/Relay Location Relay 1 Relay 2 Relay 3 Relay 4 Relay 5 Fuse Amp Rating — — — — — Passenger Compartment Fuse Panel Description Interior Lamp Relay Battery Saver Relay Rear Window Defroster Relay One Touch Down Window Relay ACC Delay Relay Power distribution box The power distribution box is located in the engine compartment. The power distribution box contains high-current fuses that protect your vehicle’s main electrical systems from overloads.
Fuse/Relay Location 1 2 3 4 5 6 Fuse Amp Rating 20A * 30A* 30A* 20A* 20A* 15A* 7 8 9 20A* 30A* 15A* 10 11 12 13 14 15 20A* 20A* 10A* 15A* — 10A* FUSE 1 FUSE 2 FUSE 3 FUSE 4 FUSE 5 FUSE 6 FUSE 7 FUSE 8 FUSE 9 FUSE 10 FUSE 11 FUSE 12 FUSE 13 FUSE 14 FUSE 15 FUSE 16 FUSE 17 FUSE 18 FULL RELAY 301 MAXI FUSE 108 MAXI FUSE 107 MAXI FUSE 104 MAXI FUSE 112 MAXI FUSE 111 MAXI FUSE 103 MAXI FUSE 116 HALF RELAY 202 MAXI FUSE 102 MAXI FUSE 101 MAXI FUSE 110 MAXI FUSE 114 MAXI FUSE 118 MAXI
Roadside emergencies Fuse/Relay Location 16 17 18 Fuse Amp Rating — 10A* 15A* 19 20 21 22 23 10A* 10A* — — 15A* 24 101 102 103 104 105 106 107 108 109 110 111 — 30A** 50A** 50A** 30A** 40A** — — 30A** 50A** 30A** 40A** 112 30A** 113 40A** 114 115 116 117 30A** — 40A** — Power Distribution Box Description Not Used Flip Windows Powertrain Control Module, Fuel Injectors, Fuel Pump, Mass Air Flow Sensor Trailer Tow Stop and Right Turn Lamp Trailer Tow Stop and Left Turn Lamp Not Used Not Used HEGO S
Roadside emergencies Fuse/Relay Location 118 201 202 203 204 205 206 207 208 209 301 302 303 304 401 501 502 503 601 Fuse Amp Rating — — — — — — — — — — — — — — — — — — 30A 602 — *Mini fuses **Maxi fuses Power Distribution Box Description Not Used Trailer Tow Park Lamp Relay Front Wiper Run/Park Relay Trailer Tow Backup Lamp Relay A/C Clutch Relay Rear Wiper Down Foglamp Relay Front Washer Pump Relay Rear Washer Pump Relay Rear Wiper Up Fuel Pump Relay Trailer Tow Battery Charge Relay Wiper Hi/Lo Relay P
Roadside emergencies Spare tire information Your vehicle is equipped with a spare tire that may be used as a spare or a regular tire. The spare is identical to the other tires on your vehicle, although the wheel trim may not match.
Roadside emergencies • To assemble, screw the parts together. To disassemble, unscrew. Removing the spare tire 1. Open the liftgate. 2. Twist counterclockwise and remove access plug (if equipped) from guide tube located just above the rear bumper. 3. Insert the straight end of the jack handle into the guide tube. Forward motion will stop and resistance to turning will be felt when properly engaged. 4. Turn the handle counterclockwise until tire is lowered to the ground and the cable is slightly slack. 5.
Roadside emergencies Tire change procedure To prevent the vehicle from moving when you change a tire, be sure the parking brake is set, then block (in both directions) the wheel that is diagonally opposite (other side and end of the vehicle) to the tire being changed. If the vehicle slips off the jack, you or someone else could be seriously injured. On vehicles equipped with Air Suspension, turn OFF the Air Suspension switch prior to jacking, hoisting or towing your vehicle.
Roadside emergencies 6. Loosen each wheel lug nut one-half turn counterclockwise but do not remove them until the wheel is raised off the ground. 7. Turn OFF the air suspension switch (if equipped). 8. Position the jack according to the following guides and turn the jack handle clockwise until the wheel is completely off the ground.
Roadside emergencies • Front (4x2) • Front (4x4) • Rear 193
Roadside emergencies To lessen the risk of personal injury, do not put any part of your body under the vehicle while changing a tire. Do not start the engine when your vehicle is on the jack. The jack is only meant for changing the tire. • Never use the front or rear differential as a jacking point. 9. Remove the lug nuts with the lug wrench. 10. Replace the flat tire with the spare tire, making sure the valve stem is facing outward. Reinstall the lug nuts until the wheel is snug against the hub.
Roadside emergencies Batteries contain sulfuric acid which can burn skin, eyes, and clothing, if contacted. Do not attempt to push-start your vehicle. Automatic transmissions do not have push-start capability. Preparing your vehicle When the battery is disconnected or a new battery is installed, the transmission must relearn its adaptive strategy. As a result of this, the transmission may shift firmly. This operation is considered normal and will not effect function or durability of the transmission.
Roadside emergencies Connecting the jumper cables + + – – 1. Connect the positive (+) booster cable to the positive (+) terminal of the discharged battery. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. + + – – 2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery.
Roadside emergencies + + – – 3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery. + + – – 4. Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle’s engine, away from the battery and the carburetor/fuel injection system. Do not use fuel lines, engine rocker covers or the intake manifold as grounding points. Do not connect the end of the second cable to the negative (-) terminal of the battery to be jumped.
Roadside emergencies Jump starting 1. Start the engine of the booster vehicle and run the engine at moderately increased speed. 2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both engines for an additional three minutes before disconnecting the jumper cables. Removing the jumper cables + + – – Remove the jumper cables in the reverse order that they were connected. 1. Remove the jumper cable from the ground metal surface.
Roadside emergencies + + – – 3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’s battery. + + – – 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’s battery. After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn its idle conditions.
Roadside emergencies WRECKER TOWING If you need to have your vehicle towed, contact a professional towing service or, if you are a member, your roadside assistance center. It is recommended that your vehicle be towed with a wheel lift or flatbed equipment. Do not tow with a slingbelt. Ford Motor Company has not approved a slingbelt towing procedure. If equipped with air suspension, the air suspension control must be turned to the OFF position.
Maintenance and care SERVICE RECOMMENDATIONS To help you service your vehicle: • We highlight do-it-yourself items in the engine compartment for easy location. • We provide a scheduled maintenance guide which makes tracking routine service easy. If your vehicle requires professional service, your dealership can provide the necessary parts and service. Check your Warranty Guide to find out which parts and services are covered.
Maintenance and care Do not start your engine with the air cleaner removed and do not remove it while the engine is running. OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located under the bottom of the instrument panel. 2. Go to the front of the vehicle and release the auxiliary latch that is located under the front center of the hood. 3. Lift the hood until the lift cylinders hold it open.
Maintenance and care IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 4.6L V8 and 5.4L V8 engines 1. Battery 2. Automatic transmission fluid dipstick 3. Engine oil filler cap 4. Engine oil dipstick 5. Power steering fluid reservoir 6. Brake fluid reservoir 7. Power distribution box 8. Air filter assembly 9. Engine coolant reservoir 10. Windshield washer fluid reservoir ENGINE OIL Checking the engine oil Refer to the scheduled maintenance guide for the appropriate intervals for checking the engine oil. 1.
Maintenance and care 2. Turn the engine off and wait a few minutes for the oil to drain into the oil pan. 3. Set the parking brake and ensure the gearshift is securely latched in P (Park). 4. Open the hood. Protect yourself from engine heat. 5. Locate and carefully remove the engine oil level indicator (dipstick). MIN MAX 6. Wipe the indicator clean. Insert the indicator fully, then remove it again. • If the oil level is between the MIN and MAX marks, the oil level is acceptable. DO NOT ADD OIL.
Maintenance and care • Oil levels above the MAX mark may cause engine damage. Some oil must be removed from the engine by a service technician. 7. Put the indicator back in and ensure it is fully seated. Adding engine oil 1. Check the engine oil. For instructions, refer to Checking the engine oil in this chapter. 2. If the engine oil level is not within the normal range, add only certified engine oil of the recommended viscosity.
Maintenance and care Change your engine oil and filter according to the appropriate schedule listed in the scheduled maintenance guide. Ford production and aftermarket (Motorcraft) oil filters are designed for added engine protection and long life. If a replacement oil filter is used that does not meet Ford material and design specifications, start-up engine noises or knock may be experienced.
Maintenance and care If you use a brake fluid that is not DOT 3, you will cause permanent damage to your brakes. Do not let the fluid level in the reservoir for the master cylinder fall below the MIN mark. If master cylinder runs dry, this may cause the brakes to fail. WINDSHIELD WASHER FLUID Washer fluid Check the washer fluid whenever you stop for fuel. The reservoir is symbol. highlighted with a If the level is low, add enough fluid to fill the reservoir.
Maintenance and care ENGINE COOLANT Checking engine coolant The concentration and level of engine coolant should be checked at the mileage intervals listed in the scheduled maintenance guide. The coolant concentration should be maintained at 50/50 coolant and water, which equates to a freeze point of -36° C (-34° F). Coolant concentration testing is possible with a hydrometer or antifreeze tester (such as the Rotunda Battery and Antifreeze Tester, 014–R1060).
Maintenance and care • Refer to the Scheduled Maintenance Guide for service interval schedules. • Be sure to read and understand Precautions when servicing your vehicle in this chapter. If the engine coolant has not been checked at the recommended interval, the engine coolant reservoir may become low or empty. If the reservoir is low or empty, add engine coolant to the reservoir. Refer to Adding engine coolant in this chapter.
Maintenance and care • Do not add/mix an orange-colored, extended life coolant such as Motorcraft Speciality Orange Engine Coolant, VC-2 (US) or CXC-209 (Canada), meeting Ford specification WSS-M97B44–D with the factory-filled coolant. Mixing Motorcraft Speciality Orange Engine Coolant or any orange-colored extended life product with your factory filled coolant can result in degraded corrosion protection.
Maintenance and care 4. When you are sure that all the pressure has been released, use the cloth to turn it counterclockwise and remove the cap. 5. Fill the coolant reservoir slowly with the proper coolant mixture (see above), to within the “cold fill range” or the “cold full” level on the reservoir. If you removed the radiator cap in an overflow system, fill the radiator until the coolant is visible and radiator is almost full. 6. Replace the cap. Turn until tightly installed.
Maintenance and care Coolant refill capacity To find out how much fluid your vehicle’s cooling system can hold, refer to Refill capacities in the Capacities and specifications chapter. Fill your engine coolant reservoir as outlined in Adding engine coolant in this chapter. Severe climates If you drive in extremely cold climates (less than –36° C [–34° F]): • it may be necessary to increase the coolant concentration above 50%. • NEVER increase the coolant concentration above 60%.
Maintenance and care What you should know about fail-safe cooling If the engine coolant supply is depleted, this feature allows the vehicle to be driven temporarily before incremental component damage is incurred. The “fail-safe” distance depends on ambient temperatures, vehicle load and terrain. How fail-safe cooling works If the engine begins to overheat: • the engine coolant temperature gauge will move to the red (hot) area. and the symbol • the will illuminate.
Maintenance and care 3. If this is not possible, wait a short period for the engine to cool. 4. Check the coolant level and replenish if low. Never remove the coolant reservoir cap while the engine is running or hot. 5. Restart the engine and take your vehicle to a service facility. Driving the vehicle without repairing the engine problem increases the chance of engine damage. Take your vehicle to a service facility as soon as possible.
Maintenance and care 4. Check the fluid level in the reservoir. It should be between the MIN and MAX lines. Do not add fluid if the level is in this range. 5. If the fluid is low, add fluid in small amounts, continuously checking the level until it reaches the range between the MIN and MAX lines. Be sure to put the cap back on the reservoir.
Maintenance and care 5. Remove the dipstick, wiping it clean with a clean, dry lint free rag. If necessary, refer to Identifying components in the engine compartment in this chapter for the location of the dipstick. 6. Install the dipstick making sure it is fully seated in the filler tube. 7. Remove the dipstick and inspect the fluid level. The fluid should be in the designated area for normal operating temperature or ambient temperature.
Maintenance and care Adjusting automatic transmission fluid levels Before adding any fluid, make sure the correct type is used. The type of fluid used is normally indicated on the dipstick and also in the Lubricant specifications section in the Capacities and specifications chapter. Use of a non-approved automatic transmission fluid may cause internal transmission component damage. If necessary, add fluid in 250 mL (1/2 pint) increments through the filler tube until the level is correct.
Maintenance and care If the electrolyte level in the battery is low, you can add plain tap water to the battery, as long as you do not use hard water (water with a high mineral or alkali content). If possible, however, try to only fill the battery cells with distilled water. If the battery needs water often, have the charging system checked. If your battery has a cover/shield, make sure it is reinstalled after the battery has been cleaned or replaced.
Maintenance and care Battery posts, terminals and related accessories contain lead and lead compunds. Wash hands after handling. For information on transmission operation after the battery has been disconnected see “Shift strategy” in the driving section. To account for customer driving habits and conditions, your automatic transmission (4R100) electronically controls the shift quality by using an adaptive learning strategy. The adaptive learning strategy is maintained by power from the battery.
Maintenance and care RN LE A TU D RE If the battery has been disconnected or a new battery has been installed, the clock and the preset radio stations must be reset once the battery is reconnected. • Always dispose of automotive batteries in a responsible manner. Follow your local authorized standards for disposal. Call your local authorized recycling center to find out more about recycling automotive batteries.
Maintenance and care Changing the air filter element 1. Loosen the clamp that secures the air inlet tube to the engine air filter cover and disconnect the tube from the cover. 2. Loosen the clamp that secures the air filter cover to the air filter housing and carefully separate the cover from housing. 3. Remove the air filter element from the air filter housing.
Maintenance and care 4. Install a new air filter element. Be careful not to crimp the filter element edges between the air filter housing and cover. This could cause filter damage and allow unmetered air to enter the engine if not properly seated. 5. Replace the air filter cover and secure the clamp. 6. Replace the air inlet tube and secure the clamp. WINDSHIELD WIPER BLADES Check the wiper blades at least twice a year or when they seem less effective.
Maintenance and care INFORMATION ABOUT UNIFORM TIRE QUALITY GRADING New vehicles are fitted with tires that have a rating on them called Tire Quality Grades. The Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width. For example: • Treadwear 200 Traction AA Temperature A These Tire Quality Grades are determined by standards that the United States Department of Transportation has set.
Maintenance and care The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning or peak traction characteristics. Temperature A B C The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel.
Maintenance and care Tire rotation Because your vehicle’s tires perform different jobs, they often wear differently. To make sure your tires wear evenly and last longer, rotate them as indicated in the scheduled maintenance guide. If you notice that the tires wear unevenly, have them checked. • Four tire rotation Replacing the tires Replace the tires when the wear band is visible through the tire treads. When replacing full size tires, never mix radial bias-belted, or bias-type tires.
Maintenance and care Make sure that all replacement tires are of the same size, type, load-carrying capacity and tread design (e.g., “All Terrain”, etc.), as originally offered by Ford. Do not replace your tires with “high performance” tires or larger size tires. Failure to follow these precautions may adversely affect the handling of the vehicle and make it easier for the driver to lose control and roll over.
Maintenance and care WHAT YOU SHOULD KNOW ABOUT AUTOMOTIVE FUELS Important safety precautions Do not overfill the fuel tank. The pressure in an overfilled tank may cause leakage and lead to fuel spray and fire. The fuel system may be under pressure. If the fuel filler cap is venting vapor or if you hear a hissing sound, wait until it stops before completely removing the fuel filler cap. Otherwise, fuel may spray out and injure you or others.
Maintenance and care Observe the following guidelines when handling automotive fuel: • Extinguish all smoking materials and any open flames before fueling your vehicle. • Always turn off the vehicle before fueling. • Automotive fuels can be harmful or fatal if swallowed. Fuel such as gasoline is highly toxic and if swallowed can cause death or permanent injury. If fuel is swallowed, call a physician immediately, even if no symptoms are immediately apparent.
Maintenance and care The flow of fuel through a fuel pump nozzle can produce static electricity, which can cause a fire if fuel is pumped into an ungrounded fuel container. Use the following guidelines to avoid static build-up when filling an ungrounded fuel container: • Place approved fuel container on the ground. • DO NOT fill a fuel container while it is in the vehicle. • Keep the fuel pump nozzle in contact with the fuel container while filling.
Maintenance and care Fuel quality If you are experiencing starting, rough idle or hesitation driveability problems during a cold start, try a different brand of “Regular” unleaded gasoline. “Premium” unleaded gasoline is not recommended (particularly in the United States) because it may cause these problems to become more pronounced. If the problems persist, see your dealer or a qualified service technician.
Maintenance and care Fuel Filler Cap Your fuel tank filler cap has an indexed design with a 1/8 turn on/off feature. When fueling your vehicle: 1. Turn the engine off. 2. Carefully turn the filler cap counterclockwise 1/8 of a turn until it stops. 3. Pull to remove the cap from the fuel filler pipe. 4. To install the cap, align the tabs on the cap with the notches on the filler pipe. 5. Turn the filler cap clockwise 1/8 of a turn until it stops.
Maintenance and care ESSENTIALS OF GOOD FUEL ECONOMY Measuring techniques Your best source of information about actual fuel economy is you, the driver. You must gather information as accurately and consistently as possible. Fuel expense, frequency of fillups or fuel gauge readings are NOT accurate as a measure of fuel economy. We do not recommend taking fuel economy measurements during the first 1 600 km (1 000 miles) of driving (engine break-in period).
Maintenance and care Calculating fuel economy 1. Fill the fuel tank completely and record the initial odometer reading (in kilometers or miles). 2. Each time you fill the tank, record the amount of fuel added (in liters or gallons). 3. After at least three to five tank fill-ups, fill the fuel tank and record the current odometer reading. 4. Subtract your initial odometer reading from the current odometer reading. 5.
Maintenance and care • Using the air conditioner or defroster may reduce fuel economy. • You may want to turn off the speed control in hilly terrain if unnecessary shifting between third and fourth gear occurs. Unnecessary shifting of this type could result in reduced fuel economy. • Warming up a vehicle on cold mornings is not required and may reduce fuel economy. • Resting your foot on the brake pedal while driving may reduce fuel economy. • Combine errands and minimize stop-and-go driving.
Maintenance and care EPA window sticker Every new vehicle should have the EPA window sticker. Contact your dealer if the window sticker is not supplied with your vehicle. The EPA window sticker should be your guide for the fuel economy comparisons with other vehicles. It is important to note the box in the lower left corner of the window sticker. These numbers represent the Range of L/100 km (MPG) expected on the vehicle under optimum conditions.
Maintenance and care Exhaust leaks may result in entry of harmful and potentially lethal fumes into the passenger compartment. Do not make any unauthorized changes to your vehicle or engine. By law, vehicle owners and anyone who manufactures, repairs, services, sells, leases, trades vehicles, or supervises a fleet of vehicles are not permitted to intentionally remove an emission control device or prevent it from working.
Maintenance and care • Foglamps • High-mount brakelamp • Brakelamps • Parking lamps • Turn signals • License plate lamp • Tail lamps • Back-up lamps Do not remove lamp bulbs unless they can be replaced immediately with new ones. If a bulb is removed for an extended period of time, contaminants may enter the lamp housings and affect lamp performance. Replacing headlamp bulbs 1. Make sure that the headlamp control is in the OFF position. 2. Open the hood. 3.
Maintenance and care Handle a halogen headlamp bulb carefully and keep out of children’s reach. Grasp the bulb only by its plastic base and do not touch the glass. The oil from your hand could cause the bulb to break the next time the headlamps are operated. 8. Insert the glass end of the new bulb into the headlamp assembly. When the grooves in the plastic base are aligned, push the bulb into the lamp assembly until the plastic base contacts the rear of the lamp assembly. 9.
Maintenance and care 4. Rotate the bulb socket counterclockwise and remove from the lamp assembly. 5. Carefully pull the bulb out of the socket and push in the new bulb. 6. Install the bulb socket into the lamp assembly and rotate clockwise. 7. Install parking lamp assembly on vehicle. 8. Push gently until parking lamp assembly seats. 9. Install screw on the lamp assembly.
Maintenance and care Replacing foglamp bulbs 1. Remove the bulb socket from the foglamp by turning counterclockwise. 2. Disconnect the electrical connector from the foglamp bulb. 3. Connect the new foglamp bulb to the electrical connector. 4. Install the bulb socket in the foglamp turning clockwise. Replacing running board lamp bulbs For bulb replacement, see a dealer or qualified technician. High-mount brakelamp To change the high-mount brakelamp bulbs: 1.
Maintenance and care Replacing license plate lamp bulbs The license plate bulbs are located behind the rear bumper. To change the license plate lamp bulbs: 1. Reach behind the rear bumper to locate the bulb. 2. Twist the bulb socket counterclockwise and carefully pull to remove it from the lamp assembly. 3. Pull out the old bulb from the socket and push in the new bulb. 4. Install the bulb socket in lamp assembly by turning it clockwise.
Maintenance and care REPLACING THE INTERIOR BULBS Check the operation of the following interior bulbs frequently: • interior overhead lamp • map lamp For bulb replacement, see a dealer or qualified technician. Map lamps To change the map lamp bulbs: 1. Use a small screwdriver to remove the map lamp lens. 2. To remove the old bulb, twist 1⁄4 turn and pull it out. 3. Twist in a new bulb. 4. Align and press the map lamp lens back on and test the lamp operation.
Maintenance and care Washing your vehicle Wash your vehicle regularly with cold or lukewarm water. Never use strong detergents or soap. If your vehicle is particularly dirty, use a quality car wash detergent. Always use a clean sponge, washing glove or similar device and plenty of water for best results. To avoid spots, avoid washing when the hood is still warm, immediately after or during exposure to strong sunlight. During winter months, it is especially important to wash the vehicle on a regular basis.
Maintenance and care Avoid getting wax on the windshield, or on any surfaces which appear coarse or bumpy. If you have wax applied at a commercial car wash, it is recommended that you clean the wiper blades and windshield as described in Cleaning the wiper blades and windshield.
Maintenance and care • Cover the highlighted areas to prevent water damage when cleaning the engine. • Never wash or rinse the engine while it is running; water in the running engine may cause internal damage. Cleaning non-painted plastic exterior parts Use vinyl cleaner for routine cleaning. Clean with a tar remover if necessary. Do not clean plastic parts with thinners, solvents or petroleum-based cleaners. Cleaning the exterior lamps Wash with the same detergent as the exterior of your vehicle.
Maintenance and care the windshield or rear window with a non-abrasive cleaner such as Ford Ultra-Clear Spray Glass Cleaner, (E4AZ-19C507–AA), available from your Ford Dealer. Do not use abrasive cleansers on glass as they may cause scratches. The windshield or rear window is clean if beads do not form when you rinse it with water. The windshield, rear window and wiper blades should be cleaned on a regular basis, and blades or rubber elements replaced when worn.
Maintenance and care Woodtone trim Wipe stains with a soft cloth and a multi-purpose cleaning solution. Cleaning leather seats (if equipped) To clean, simply use a soft cloth dampened with water and a mild soap. Wipe the leather again with a damp cloth to remove soap residue. Dry with a soft cloth. For tougher soiling concerns, Ford recommends using the Deluxe Leather Care Kit F8AZ-19G253–AA, which is available from your Ford Dealer.
Capacities and specifications MOTORCRAFT PART NUMBERS Component Air filter element Battery Fuel filter Oil filter PCV valve Spark plugs* 4.6L V8 engine FA-1634 BTX-65-650 FG-986B FL-820-S EV-233 AWSF-32P 5.4L V8 engine FA-1634 BTX-65-650 FG-986B FL-820-S EV-233 AWSF-22W * Refer to Vehicle Emissions Control Information (VECI) decal for spark plug gap information.
Capacities and specifications Fluid Ford Part Name Motorcraft MERCON威V ATF Motorcraft MERCON威 ATF Transmission fluid 1 Application Capacity 4R70W 13.1L (13.9 quarts) 2 4R100 (4x2) 15.0L (15.9 quarts) 2 15.5L (16.4 quarts) 2 1.9L (2.0 quarts) 20.5 L (21.7 quarts) 4R100 (4x4) Transfer case fluid Engine coolant 3 Motorcraft MERCON威 ATF Motorcraft Premium Engine Coolant (green-colored) or Motorcraft Premium Gold Engine Coolant (yellow-colored) 4x4 vehicles 4.6L V8 engine with 1 row radiator 4.
Capacities and specifications Fluid Front axle lubricant Rear axle lubricant 4 Windshield washer fluid Ford Part Name Motorcraft SAE 75W-90 Premium 4x4 Front Axle Lubricant Motorcraft SAE 75W-140 Synthetic Rear Axle Lubricant Ultra-Clear Windshield Washer Concentrate Application Capacity 5.4L V8 engine 26.4L (27.9 with 2 row quarts) radiator and aux rear heat 4x4 vehicles 1.8-2.0L (3.5-3.7 pints) All 2.9-3.1L (5.5-5.8 pints) All 4.1L (4.
Capacities and specifications 2 Indicates only approximate dry-fill capacity. Some applications may vary based on cooler size and if equipped with an in-tank cooler. The amount of transmission fluid and fluid level should be set by the indication on the dipstick’s normal operating range. 3 Add the coolant type originally equipped in your vehicle. 4 Your vehicle’s rear axle is filled with a synthetic rear axle lubricant and is considered lubricated for life.
Capacities and specifications Item Driveshaft, slip spline, double Cardan joint center ball Engine coolant Ford part name Premium Long Life Grease Motorcraft Premium Engine Coolant (green-colored) Motorcraft Premium Gold Engin Coolant (yellow-colored) Engine oil Motorcraft SAE 5W20 Super Premium Motor Oil 4x4 front wheel High Temperature bearings, 4x4 4x4 Front Axle spindle needle bearings, spindle & Wheel Bearing thrust bearings Grease & front drive axle u-joint/slip spline Motorcraft Automatic MERCON威 A
Capacities and specifications Item Rear axle2 Front axle (4X4) Transfer case (4X4) Windshield washer fluid Ford part name Motorcraft SAE 75W-140 High Performance Synthetic Rear Axle Lube Motorcraft SAE 75W-90 Premium 4x4 Front Axle Lubricant Motorcraft MERCON威 ATF Ultra-clear Windshield Washer Concentrate Ford part number F1TZ-19580-B Ford specification WSL-M2C192-A XY-75W90-TQL WSP-M2C201-A XT-2-QDX MERCON威 C9AZ-19550-AC ESR-M17P5-A 1 Ensure the correct automatic transmission fluid is used.
Capacities and specifications ENGINE DATA Engine Cubic inches Required fuel Firing order Spark plug gap Ignition system Compression ratio 4.6L V8 engine 281 87 octane 1-3-7-2-6-5-4-8 1.3-1.4 mm (0.052-0.056 inch) Coil on plug 9.37:1 5.4L V8 engine 330 87 octane 1-3-7-2-6-5-4-8 1.3-1.4 mm (0.052-0.056 inch) Coil on plug 9.0:1 VEHICLE DIMENSIONS Vehicle dimensions 4x2 mm (in) (1) Overall length 5 196.0 (204.6) (2) Vehicle width 2 000.0 (78.7)1 *width including 2 293 mirrors (90.
Capacities and specifications 2 Vehicle equipped with 16” tires and base suspension 4 1 3 5 2 255
Capacities and specifications IDENTIFYING YOUR VEHICLE Certification label The National Highway Traffic Safety Administration Regulations require that a Certification label be affixed to a vehicle and prescribe where the Certification label may be located. The Certification label is located on the front door latch pillar on the driver’s side. Vehicle identification number The vehicle identification number is attached to a metal tag and is located on the driver side instrument panel.
Customer assistance Ford Extended Service Plan You can get more protection for your new car or light truck by purchasing Ford Extended Service Plan (Ford ESP) coverage. Ford ESP is an optional service contract which is backed by Ford Motor Company or Ford Motor Service Company (in the U.S.) and Ford of Canada (in Canada).
Customer assistance taken to another dealer. If a particular dealership can not assist you, then contact the Customer Relationship Center. If you have questions or concerns, or are unsatisfied with the service you are receiving, follow these steps: 1. Contact your Sales Representative or Service Advisor at your selling/servicing dealership. 2. If your inquiry or concern remains unresolved, contact the Sales Manager or Service Manager at the dealership. 3.
Customer assistance In the United States: Ford Motor Company Customer Relationship Center 16800 Executive Plaza Drive P.O. Box 6248 Dearborn, Michigan 48121 1-800-521-4140 (TDD for the hearing impaired: 1-800-232-5952) In Canada: Customer Relationship Centre Ford Motor Company of Canada, Limited P.O.
Customer assistance THE DISPUTE SETTLEMENT BOARD (U.S. only) The Dispute Settlement Board is: • an independent, third-party arbitration program for warranty disputes • available free to owners and lessees of qualifying Ford Motor Company vehicles The Dispute Settlement Board may not be available in all states. Ford Motor Company reserves the right to change eligibility limitations, modify procedures and/or to discontinue this service without notice and without incurring obligations per applicable state law.
Customer assistance Board membership The Board consists of: • three consumer representatives • a Ford or Lincoln Mercury dealership representative Consumer candidates for Board membership are recruited and trained by an independent consulting firm. The dealership Board member is chosen from Ford and Lincoln Mercury dealership management, recognized for their business leadership qualities.
Customer assistance You will receive a letter of explanation if your application does not qualify for Board review. Oral presentations If you would like to make an oral presentation, indicate YES to question 6 on the application. While it is your right to make an oral presentation before the Board, this is not a requirement and the Board will decide the case whether or not an oral presentation is made. An oral presentation may be requested by the Board as well.
Customer assistance UTILIZING THE MEDIATION/ARBITRATION PROGRAM (CANADA ONLY) In those cases where you continue to feel that the efforts by Ford and the dealer to resolve a factory-related vehicle service concern have been unsatisfactory, Ford of Canada participates in an impartial third party mediation/arbitration program administered by the Canadian Motor Vehicle Arbitration Plan (CAMVAP).
Customer assistance If your vehicle must be serviced while you are traveling or living in Central or South America, the Caribbean, or the Middle East, contact the nearest Ford dealership. If the dealership cannot help you, write or call: FORD MOTOR COMPANY WORLDWIDE DIRECT MARKET OPERATIONS 1555 Fairlane Drive Fairlane Business Park #3 Allen Park, Michigan 48101 U.S.A. Telephone: (313) 594-4857 FAX: (313) 390-0804 If you are in another foreign country, contact the nearest Ford dealership.
Customer assistance Ford Multi-Purpose Cleaner* Motorcraft Car Wash Concentrate Motorcraft Carlite Glass Cleaner Ford Spot and Stain Remover* Ford Super Premium Tire and Trim Dressing Ford Triple Clean Ford Ultra-Clear Spray Glass Cleaner (not available in Canada) * May be sold with the Motorcraft name FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of Ford accessories are available for your vehicle through your local authorized Ford, Lincoln Mercury or Ford of Canada dealer.
Customer assistance Carpeted cargo mat Dash trim (wood grain) Engine block heaters Tire step Travel equipment Auto headlamps with DRL Bike rack Bumper mount bike carrier Canoe carrier Cell phone holder Daytime running lights (DRL) Factory luggage rack adaptors Fog lights Framed luggage covers Hard side luggage box Hard side ski box Heavy-duty battery Kayak carrier Luggage/cargo basket Removable luggage rack (Track rider bars) Removable luggage rack adapters Running boards (Molded and tubular) Seatback organ
Customer assistance Protection and appearance equipment Air bag anti-theft locks Cargo liners, interior Carpet floor mats Door edge guards Fender flares Flat splash guards Front end covers (full and sport) Hood deflectors Inside mirror with compass display Inside mirror with compass and temperature display Leather steering wheel Locking gas cap Molded splash guards Molded vinyl floor mats Moonroof deflector Outside signal mirror (requires power mirrors) Rear air deflectors Side window air deflectors Spare t
Customer assistance • The Federal Communications Commission (FCC) and Canadian Radio Telecommunications Commission (CRTC) regulate the use of mobile communications systems - such as two-way radios, telephones and theft alarms - that are equipped with radio transmitters. Any such equipment installed in your vehicle should comply with FCC or CRTC regulations and should be installed only by a qualified service technician.
Customer assistance IN CALIFORNIA (U.S. ONLY) California Civil Code Section 1793.
Reporting safety defects REPORTING SAFETY DEFECTS (U.S. ONLY) If you believe that your vehicle has a defect that could cause a crash, or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Ford Motor Company. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.
Index A Accessory delay ..........................89 Air bag supplemental restraint system ........................128–129, 134 and child safety seats ............131 description ......................129, 134 disposal ............................133, 137 driver air bag ..................131, 135 indicator light ...........11, 133, 136 operation .........................131, 135 passenger air bag ...........131, 135 side air bag ..............................134 Air cleaner filter .......
Index Cassette tape player ...................28 CD changer .................................52 Certification Label ....................256 Child safety restraints ..............137 child safety belts ....................137 Child safety seats ......................138 attaching with tether straps ...............................143–144 in front seat ............................140 in rear seat ..............140, 142–143 Cleaning your vehicle ...............242 engine compartment ..............244 exterior .
Index Driving under special conditions ..................................167 mud ..........................................166 sand .........................................166 snow and ice ...........................167 through water .................166, 168 E Emergencies, roadside jump-starting ..........................194 Emission control system ..........235 Engine ........................................254 check engine/service engine soon light ..................................10 cleaning .........
Index Gas mileage (see Fuel economy) ...................................232 Gauges .........................................16 battery voltage gauge ...............18 engine coolant temperature gauge .........................................17 engine oil pressure gauge ........19 fuel gauge ..................................16 odometer ...................................17 speedometer .............................17 tachometer ................................18 trip odometer ............................
Index L Lamps autolamp system .......................23 bulb replacement specifications chart ................241 cargo lamps ...............................22 daytime running light ...............21 fog lamps ...................................22 headlamps .................................21 headlamps, flash to pass ..........21 instrument panel, dimming .....22 interior lamps .............82–83, 242 replacing bulbs ...............236–241 Lane change indicator (see Turn signal) ............................
Index Power distribution box (see Fuses) ........................................185 Power door locks ................89, 101 Power steering ..................155–156 fluid, checking and adding ....214 fluid, refill capacity ................248 fluid, specifications .........251, 254 Preparing to drive your vehicle 158 R Radio ............................................27 Rear window defroster ...............23 Relays ................................181, 188 Remote entry system ...........
Index replacing ..................................225 rotating ....................................225 snow tires and chains ............226 tire grades ...............................224 treadwear ................................223 Towing .......................................171 recreational towing .................175 trailer towing ..........................171 wrecker ....................................200 Traction-lok rear axle ...............157 Transmission .............................
Filling station information Item Required fuel Fuel tank capacity-4x2 without air suspension Fuel tank capacity-4x4 vehicles and 4x2 vehicles with rear load level suspension Engine oil (includes filter change) Tire size and pressure Hood release Coolant capacity 1 Power steering fluid capacity Automatic transmission fluid capacity-4R70W 2 Automatic transmission fluid capacity-4R100 (4x2) 2 Automatic transmission fluid capacity-4R100 (4x4) 2 Information Unleaded fuel only - 87 octane 98.6L (26.
Filling station information Some transmission fluids may be labeled as dual usage, such as MERCON威 and MERCON威 V. These dual usage fluids are not to be used in an automatic transmission that requires use of the MERCON威 type fluid. However, these dual usage fluids may be used in transmissions that require the MERCON威 V type fluid. MERCON威 and MERCON威 V type fluids are not interchangeable. DO NOT mix MERCON威 and MERCON威 V.
