Spec Sheet

3
Form# 7015
Maestro Plus top mount foodservice Maestro Plus top mount foodservice
Dimensional drawing
8.03"
(20.4 cm)
5.03"
(12.8 cm)
2.34"
(5.94 cm)
15.22"
(38.65 cm)
2.324" (5.90 cm)
4.409" (11.20 cm)
2.123" (10.78 cm)
11.03"
(28.0 cm)
Back view – air-cooled, top mount
Back view – water-cooled, top mount
H2
H1
D1
D3
C3
W2
W1
C1
C1
C2
C4
C5
H1
H3
W1
5.03"
(12.8 cm)
15.22"
(38.65 cm)
2.34"
(5.94 cm)
2.324" (5.90 cm)
4.409" (11.20 cm)
2.123" (10.78 cm)
C3
C1
C2
W1
C1
D2
H1
Specification for bin top mount ice machines
W1 Width 22.70" (57.6 cm)
fits on 22.00" wide dispensers orbins
D1 Depth, ice machine 24.25" (61.6 cm)
D2 Depth, bin 31.50" (80.0 cm)
H1 Height 21.25" (54.0 cm)
Service clearance 12.00" (30.5 cm) top -
no frontobstructions
6.00" (15.24 cm) on exhaust side (left,
right and rear)
C1 Electrical
115 V/60/1
11 amps, 0.8 kW
15 amp circuit
7' (2 m) cord, NEMA 5-15 plug
C2 Water inlet 3/8" FPT, installation of an in line water
filtration system is recommended
C3 Drain  3/4" MPT
water-cooled models require separate
condenser drains
Water-cooled ice machine
connections
C4 – 3/8" FPT condenser inlet
C5 – 3/8" FPT condenser drain
Refrigerant R404a
Air temperature 50 -100 F (10 - 38 C)
Water temperature 45 - 90 F (7 - 32 C)
Potable water pressure 10 - 70 psi (69 - 483 kPa)
Condenser water pressure 10 - 125 psi (69 - 861 kPa)
Chewblet, ice production at
70 F (21 C) air, 50 F (10 C) water
air-cooled models – 425 lb (193.0 kg)
water-cooled models – 443 lb (201.1 kg)
Chewblet ice production at
90 F (32 C) air, 70 F (21 C) water
air-cooled models – 325 lb (147.6 kg)
water-cooled models – 372 lb (169.0 kg)
Flake ice production at
90 F (32 C) air, 70 F (21 C) water
water-cooled models – 515 lb (234 kg)
Chewblet energy consumption
90 F (32 C) air, 70 F (21C) water
air-cooled models – 5.4 kWh
water-cooled models – 5.0 kWh
per 100lb(45 kg) ice
Flake energy consumption
90 F (32 C) air, 70 F (21C) water
water-cooled models – 6.2 kWh
per 100lb(45 kg) ice
Heat rejection air-cooled models – 5,000 BTU/hr
water-cooled models – 1,400 BTU/hr
to air, 3,600 BTU/hr to water
Water consumption,
Chewblet and flake ice
12.0 gal (45.4 L) of potable water per
100lb (45.4 kg) of ice. 12.5 gal (47.3 L)
at standard flush setting.
Water flow requirement for
water-cooled condensers
0.25 gpm at 50 F (10 C)
0.5 gpm at 70 F (21 C)
1.25 gpm at 90 F (32 C)
Approximate ship weight 160 lb (73 kg)
NOTE: For indoor use only
Configure your ice machine with the following bin models
Slope front bin model
Maximum bin
capacity lb (kg)
Cubic Volume
cu ft (m)
Width - W2
in (cm)
Depth - D3
in (cm)
Height - H2
in (cm)
Door Sill Height- H3
in (cm)
Required door
access in (cm)
Approx. ship
weight lb (kg)
300-22 300 (136) 9.6 (0.27) 22.00 (55.9) 29.50 (74.9) 40.00 (101.6) 26.00 (66.0) 23.00 (58.4) 128 (58)
425-30 430 (195) 13.8 (0.39) 30.00 (76.2) 29.50 (74.9) 40.00 (101.6) 26.00 (66.0) 31.00 (78.7) 144 (65)
650-44 660 (299) 20.8 (0.59) 44.00 (111.8) 29.50 (74.9) 40.00 (101.6) 26.00 (66.0) 32.00 (81.3) 178 (81)
950-48 950 (431) 30.1 (0.85) 48.00 (121.9) 28.25 (71.8) 50.00 (127.0) 36.00 (91.4) 32.00 (81.3) 207 (94)
1025-52 1030 (468) 32.6 (0.92) 52.00 (132.1) 28.25 (71.8) 50.00 (127.0) 36.00 (91.4) 32.00 (81.3) 217 (98 )
 Follett recommends installation of floor drain with grate with all ice storage bins.
 Model 300-22 only for use with Follett Maestro Plus 425, air-cooled, ice machines.
SHORT FORM SPECIFICATION: Ice machine to be
Follett model number _________. Ice machine to be
_____air- or ______water-cooled. Ice machine production
to be approximately 425 lb (193.0 kg) per day of
______Chewblet ice or ______ flake ice. Ice machine
to use environmentally responsible R404a refrigerant.
Icemachine to have stainless steel evaporator, auger and
top bearings, heavy-duty tapered roller bearing, and low-
water safety circuit. NSF and ETL listed.