Horizon Elite™ Ice Machine Models with RIDE™ Technology Installation Instructions for Cornelius PR150 HCD/HMD/HCF/HMF1010RPS, HCD/HMD/HCF/HMF1410RPS, HCD/HCF1010NPS, HMD1410NPS (See model number configurator on page 2 for details.) Order parts online www.follettice.com remote condensing 801 Church Lane • Easton, PA 18040, USA Toll free (877) 612-5086 • +1 (610) 252-7301 www.follettice.
Chewblet® Ice Machine Model Number Configurations HC Icemaker MC Maestro™ Chewblet® (400 Series) HC Horizon Chewblet (1000, 1400, 1650 Series) HM Horizon Micro Chewblet 2 Voltage C 1400 A Series 400 up to C 208-230/60/1 (icemaking head) Self-contained only. 454 lbs D 115/60/1 (icemaking head) (206kg) Self-contained and remote. If remote 1000/1010 unit, high side is 208-230/60/1. up to E 230/50/1 (icemaking head) 1036 lbs Self-contained only.
Read and complete the following 8 installation steps 1 3 5 7 Unpack Dispenser preparation Ice transport tube Internal connection 2 4 6 8 Cornelius • RIDE Technology remote condensing Site preparation Louvered docking assembly External connection Front cover 3
Carefully unpack and inspect the contents of your Follett ice machine. 1.
Site preparation Prepare the installation site. 2 Provide drainage, water supply and electrical power to within 6 feet (2m) of ice machine in accordance with local and national codes. Outdoor installation of low side is not recommended and will void warranty. 2.1 2.
Dispenser preparation Prepare the dispenser. 3.1 3 3.2 ➋ ➋ ➊ ➊ • Remove ice entry cover plate ➊ • Remove bin thermostat capillary tube from • Coil capillary tube and secure away from bin 3.3 3.4 bracket fill opening ➊ ➋ ➊ ➊ ➋ ➋ • Remove retaining clips ➊ and deflector nuts ➋ 6 • Remove capillary tube bracket ➊ and deflector (Fig. 4.
3.5 3.6 ➋ ➌ ➊ ➊ ➋ • Mount cover plate/transport tube assembly on outside of dispenser using screws, flat washers ➊, lock washers ➋ and nuts provided ❸ • Insert end of ice transport tube (with retaining holes) through hole in center of cover plate assembly ➊ • Secure ice transport tube (holes) to retaining tabs on bracket 3.7 ➋ 3.
3.9 3.
Louvered docking assembly Install the louvered docking assembly. Wall bracket accessory Machine stand accessory • Mount louvered docking assembly to wall bracket accessory 2.1 4.1 4 • Mount louvered docking assembly to machine stand accessory Louvered docking assembly 2" (50,8 mm) 1.88" (47,8 mm) ➋ ➊ 3/8˝ ∅ high pressure line 1" (25,4 mm) Stub Typ 3.
4.2 Undercounter installation requirements Top View ➌ CROSSBRACE Access panel/ door on counter ➊ 3.25" (83 mm) min. 22.25" min. (656 mm) 24" min. (609 mm No Lip ➋ DOCKING STATION • Position and screw louvered docking assembly to the bottom of counter inside of access panel/ door min. of 3.25" (83 mm) from the front edge of the cross brace ➊ • The mounting surface for the louvered docking assembly must be solid. Do not mount directly onto runners or channels.
Ice transport tube Install the ice transport tube. 5.1 5 Ice transport tube installation from dispenser to ice machine ➋ Hot Water 160 F (71 C) ➎ ➊ 1/4" ➌ 1' ➍ ➏ ➐ Ice transport tube tips • Insulate entire length of ice transport tube ➊ • Secure ice transport tube ➋ as needed to prevent dips and traps from forming. For long tube runs see guide on page 14. • Pitch ice transport tube at least 1/4" per foot (6,4mm/.
Bin signal Install the bin signal. 2.1 6.1 6 Bin Signal Installation ➏ ➎ ➐ Ground ➌ ➊ ➋ 16" (61 cm) ❹ • Mount the electrical box to the side of the Vision dispenser ➊ to establish a ground connection. Note: If a 4 x 4 box is mounted to a non-grounded surface, connect ground wire at an appropriate ground. • Connect the bin signal cord to the plug on the electrical box.
External connections Connect utilities to louvered docking assembly. 7.1 7.2 Water and drain 7 Refrigerant ➋ ➊ ➌ ➊ • Remove access panel if necessary. • Install drain line ➊. The rigid drain line from the ice machine must have at least 1/4" per foot pitch (6,4mm/0,3m). • Rough-in ice machine potable water supply ➋. 3/8" push-in connection will be made at shut-off valve inside machine • Apply Petrogel to barbed drain fitting ➌ • Replace access panel.
Connect louvered docking assembly to ice machine. 8.1 8.2 Ice transport tube installation Internal connections 8 Water line ➋ ➊ ➋ ➊ • Slide ice machine into louvered docking assembly ensuring that drain tube is fully seated on barbed drain fitting ➊ • Insert ice transport tube all the way into coupling and tighten nut firmly ➋ • Insert potable water line into valve 8.3 8.
8.6 Power cord TDS switch CLEAN POWER ON HIGH LOW BIN MAKING ICE SLEEP CYCLE TIME DELAY LOW WATER MAINT/CLEAN SERVICE HIGH AMPS HIGH PRES TDS DRAIN CLOG CLEANER FULL 8.
Front cover Install front cover to ice machine. 9.1 9.2 Install condensing unit 9 Install ice machine front cover ➋ ➊ • Slide ice machine cover over machine ensuring that tabs on back of cover slip under louvers on back of louvered docking assembly ➊ • Insert and tighten two screws through cover and into louvered docking assembly • Complete installation of condensing unit or connection to rack system. • Required rack system capacity at 0 F (-18 C) evaporator (EPR supplied by installer).
Long tube run recommendations max. 2 ft (.6m) ➋ ➊ 1/4" 1' • Pitch ice transport tube to allow melt water to drain towards ice machine ➊ • Secure insulated ice transport tube at least every 2 ft (.
remote condensing Cornelius • RIDE Technology
Cornelius • RIDE Technology remote condensing 19
Horizon, Horizon Elite, Maestro, Harmony, Ice Manager, SafeCLEAN, Sani-Sponge and Vision are trademarks of Follett Corporation. Chewblet, RIDE and Follett are registered trademarks of Follett Corporation, registered in the US. 801 Church Lane • Easton, PA 18040, USA Toll free (877) 612-5086 • +1 (610) 252-7301 www.follettice.
