Horizon Elite™ Ice Machine Models with RIDE™ Technology Installation Instructions for Ice Storage Bins HCD/HMD/HCF/HMF1010RBS, HCD/HMD/HCF/HMF1410RBS HCD/HMD1010NBS, HCD/HMD1410NBS (See model number configurator on page 2 for details.) Order parts online www.follettice.com remote condensing 801 Church Lane • Easton, PA 18040, USA Toll free (877) 612-5086 • +1 (610) 252-7301 www.follettice.
Chewblet® Ice Machine Model Number Configurations HC Icemaker MC Maestro™ Chewblet® (400 Series) HC Horizon Chewblet (1000, 1400, 1650 Series) HM Horizon Micro Chewblet Voltage C 1400 A Series V S Condenser 400 up to C 208-230/60/1 (icemaking head) Self-contained only. 454 lbs D 115/60/1 (icemaking head) (206kg) Self-contained and remote. If remote 1000/1010 unit, high side is 208-230/60/1. up to E 230/50/1 (icemaking head) 1036 lbs Self-contained only.
Read and complete the following 8 installation steps 1 3 5 7 Unpack 2 Bin preparation 4 Ice transport tube 6 Internal connection BIN • RIDE Technology 8 self-contained Site preparation Louvered docking assembly External connection Front cover 3
Carefully unpack and inspect the contents of your Follett ice machine. 1.
Site preparation Prepare the installation site. 2 Provide drainage, water supply and electrical power to within 6 feet (2m) of ice machine in accordance with local and national codes. Outdoor installation of low side is not recommended and will void warranty. 2.1 2.
Bin preparation Prepare the bin. 3.1 3.2 Bin top preparation 3 Bin top preparation 3" ∅ (76,2mm) CL CL • Locate center of bin top • Cut 3" (77,2mm) diameter hole in bin top 3.
Louvered docking assembly Install the louvered docking assembly. Wall bracket accessory Machine stand accessory • Mount louvered docking assembly to wall bracket accessory 2.1 4.1 4 • Mount louvered docking assembly to machine stand accessory Louvered docking assembly 2" (50,8 mm) 1.88" (47,8 mm) ➋ ➊ 3/8˝ ∅ high pressure line 1" (25,4 mm) Stub Typ 3.
Transport tube Install the ice transport tube. 5.1 5 Ice transport tube installation ➍ ➏ ➐ ➋ Hot Water 160 F (71 C) ➊ ➑ ➎ ➒ ➓ 1/4" ➌ 1' Ice transport tube tips • Insulate entire length of ice transport tube ➊ • Secure ice transport tube ➋ as needed to prevent dips and traps from forming. For long tube runs see guide on page 13. • Pitch ice transport tube at least 1/4" per foot (6,4mm/.
External connections Connect utilities to louvered docking assembly. 6.1 6.2 Water and drain 6 Refrigerant ➋ ➊ ➌ ➊ • Remove access panel if necessary. • Install drain line ➊. The rigid drain line from the ice machine must have at least 1/4" per foot pitch (6,4mm/0,3m). • Rough-in ice machine potable water supply ➋. 3/8" push-in connection will be made at shut-off valve inside machine • Apply Petrogel to barbed drain fitting ➌ • Replace access panel.
Connect louvered docking assembly to ice machine. 7.1 7.2 Ice transport tube installation Internal connections 7 Water line ➋ ➊ ➋ ➊ • Slide ice machine into louvered docking assembly ensuring that drain tube is fully seated on barbed drain fitting ➊ • Insert ice transport tube all the way into coupling and tighten nut firmly ➋ • Insert potable water line into valve 7.3 7.
7.6 Power cord TDS switch CLEAN POWER ON HIGH LOW BIN MAKING ICE SLEEP CYCLE TIME DELAY LOW WATER MAINT/CLEAN SERVICE HIGH AMPS HIGH PRES TDS DRAIN CLOG CLEANER FULL 7.
Front cover Install front cover to ice machine. 8.1 8.2 Install condensing unit 8 Install ice machine front cover ➋ ➊ • Slide ice machine cover over machine ensuring that tabs on back of cover slip under louvers on back of louvered docking assembly ➊ • Insert and tighten two screws through cover and into louvered docking assembly • Complete installation of condensing unit or connection to rack system. • Required rack system capacity at 0 F (-18 C) evaporator (EPR supplied by installer).
Long tube run recommendations max. 2 ft (.6m) ➋ ➊ 1/4" 1' • Pitch ice transport tube to allow melt water to drain towards ice machine ➊ • Secure insulated ice transport tube at least every 2 ft (.
self-contained BIN • RIDE Technology
BIN • RIDE Technology self-contained 15
Horizon, Horizon Elite, Maestro, Harmony, Ice Manager, SafeCLEAN, Sani-Sponge, RIDE and Vision are trademarks of Follett Corporation. Chewblet is a registered trademark of Follett Corporation, registered in the US. 801 Church Lane • Easton, PA 18040, USA Toll free (877) 612-5086 • +1 (610) 252-7301 www.follettice.
