Horizon Elite™ Ice Machine Models with RIDE™ Technology Installation Instructions for Ice Storage Bins HMD/HCD710ABS, HCC1010ABS, HMC1010ABS, HCC1410ABS, HMC1410ABS, HCC1010WBS, HMC1010WBS, HCC1410WBS, HMC1410WBS, HCE1010ABS, HME1010ABS, HCE1410ABS, HME1410ABS, HCE1010WBS, HME1010WBS, HCE1410WBS, HME1410WBS (See model number configurator on page 2 for details.) Order parts online www.follettice.com self-contained 801 Church Lane • Easton, PA 18040, USA Toll free (877) 612-5086 • +1 (610) 252-7301 www.
Chewblet® Ice Machine Model Number Configurations HC Icemaker MC Maestro™ Chewblet® (425 Series) HC Horizon Chewblet (710, 1010, 1410, 1810, 2110 Series) HM Horizon Micro Chewblet Voltage D 1810 A V Series 425 up to C 208-230/60/1 (icemaking head) Self-contained only. 425 lbs D 115/60/1 (icemaking head) (193 kg) Self-contained and remote. If remote 710 up to unit, high side is 208-230/60/1. 675 lbs E 230/50/1 (icemaking head) (306 kg) Self-contained only.
Read and complete the following 8 installation steps 1 3 5 7 Unpack 2 Bin preparation 4 Ice transport tube 6 Internal connection BIN • RIDE Technology 8 self-contained Site preparation Louvered docking assembly External connection Front cover 3
Unpack Carefully unpack and inspect the contents of your Follett ice machine. 1.
Site preparation Prepare the installation site. 2 Provide drainage, water supply and electrical power to within 6 feet (2m) of ice machine in accordance with local and national codes. Outdoor installation is not recommended and will void warranty. 2.1 2.1 Installation site requirements H_C1010A/W NEMA 6-15 H_C1010A/W* 2 ft. x 1" OD silicone tubing and fittings provided requires 15A circuit, 1.50 mm2 wire ➊ H_E1410A/W‡ requires 20A circuit, 4.
Bin preparation Prepare the bin 3.1 Bin top preparation 3.
Install the louvered docking assembly. Louvered docking assembly 4 BEFORE PROCEEDING Prior to installing the louvered docking assembly, ensure that the drain fitting is oriented (right or left) correctly for your installation. An optional straight drain fitting is also supplied. You may need to remove the back panel of the docking assembly in order to re-orient or change the drain fitting. Replace back panel prior to mounting the docking assembly.
Ice transport tube 5 Install the ice transport tube. 5.1 Ice transport tube installation ➍ ➏ ➐ ➋ Hot Water 160 F (71 C) ➎ ➑ ➊ 1/4˝ (6,4mm) ➌ ➒ ➓ 1' (0,3m) Ice transport tube tips • Insulate entire length of ice transport tube ➊ • Secure ice transport tube ➋ as needed to prevent dips and traps from forming. For long tube runs see guide on page 14. • Pitch ice transport tube at least 1/4" per foot (6,4mm/.
External connections Connect utilities to louvered docking assembly. 6.1 Air-cooled ice machines only 6.2 6 Water-cooled ice machines only ➊ ➊ ➏ ➋ ➐ ➌ Minimum 8" radius ➏ ➋ ➌ Minimum 8" radius ➑ 2 ft. x 1" OD silicone tubing 2 ft. x 1" OD silicone tubing 3/4" barb x 3/4" FPT ➍ 3/4" MPT x 1" slip ➎1" Stand pipe/Drain • Rough-in ice machine potable water supply ➊. 3/8” push-in connection will be made at shut-off valve inside machine • Remove access panel if necessary ➋.
Internal connections Connect louvered docking assembly to ice machine. 7 CAUTION • Plug must be accessible after final installation. • H_E1410A/W 230/50/1 requires a 20A circuit (4.00 mm2 wire) Air-cooled ice machines – follow steps 7.1 through 7.5. 7.1 7.
Water-cooled ice machines – follow steps 7.6 through 7.12. 7.6 Set TDS switch Cooling lines CLEAN POWER ON HIGH LOW BIN MAKING ICE SLEEP CYCLE TIME DELAY LOW WATER MAINT/CLEAN SERVICE HIGH AMPS HIGH PRES TDS DRAIN CLOG CLEANER FULL 7.5 In Out LOW • Set the TDS switch on the electrical box: HIGH: for extended service life LOW: for low-scale water 7.7 • Install ice machine cooling water lines to louvered docking assembly 7.
7.9 7.10 Cooling lines and power Power cord ➋ ➊ • Remove twist tie • Carefully pass cord thru opening and plug into wall outlet • For H_E units, install a suitable plug • Connect cooling water lines to ice machine ➊ • Water valve is set at the factory. DO NOT remove seal or adjust water valve ➋ 7.12 Power cord TDS switch CLEAN POWER ON HIGH LOW BIN MAKING ICE SLEEP CYCLE TIME DELAY LOW WATER MAINT/CLEAN SERVICE HIGH AMPS HIGH PRES TDS DRAIN CLOG CLEANER FULL 7.
Front cover Install front cover to ice machine. 8 Install front cover Front cover installation – air-cooled undercounter only ➊ ➋ ➋ ➌ ➌ ➊ • Slide ice machine cover over machine ensuring that tabs on back of cover slip under louvers on back of louvered docking assembly ➊ • Insert and tighten two screws through cover and into louvered docking assembly CAUTION • Keep ventilation openings in the appliance enclosure clear of obstruction.
Long tube run recommendations max.
BIN • RIDE Technology self-contained 15
Horizon, Horizon Elite, Maestro, Harmony, Ice Manager, SafeCLEAN, Sani-Sponge, RIDE and Vision are trademarks of Follett LLC. Chewblet is a registered trademark of Follett LLC, registered in the US. 801 Church Lane • Easton, PA 18040, USA Toll free (877) 612-5086 • +1 (610) 252-7301 www.follettice.
