Horizon Elite™ Ice Machine Models with RIDE™ Technology Installation Instructions for Cornelius PR150 HCD710APS, HCC1010APS, HCC1410APS, HCC1010WPS, HCC1410WPS, (See model number configurator on page 2 for details.) Order parts online www.follettice.com self-contained 801 Church Lane • Easton, PA 18040, USA Toll free (877) 612-5086 • +1 (610) 252-7301 www.follettice.
Chewblet® Ice Machine Model Number Configurations HC Icemaker MC Maestro™ Chewblet® (425 Series) HC Horizon Chewblet (710, 1010, 1410, 1810, 2110 Series) HM Horizon Micro Chewblet 2 Voltage D 1810 A Series V S Application Configuration Vision™ Harmony™ Ice storage bin Drop-in Ice Manager diverter valve system P Cornelius Profile PR150 S RIDE™ (RIDE remote ice delivery equipment) T Top-mount Condenser 425 up to C 208-230/60/1 (icemaking head) Self-contained only.
Read and complete the following 8 installation steps 1 3 5 7 Unpack Dispenser preparation Ice transport tube Internal connection Cornelius • RIDE Technology self-contained 2 4 6 8 Site preparation Louvered docking assembly External connection Front cover 3
Carefully unpack and inspect the contents of your Follett ice machine. 1.
Site preparation Prepare the installation site. 2 Provide drainage, water supply and electrical power to within 6 feet (2m) of ice machine in accordance with local and national codes. Outdoor installation is not recommended and will void warranty. 2.1 2.1 Installation site requirements H_C1010A/W NEMA 6-15 HCD710A NEMA 5-15 H_C1410A/W NEMA 6-20 2 ft.
Dispenser preparation Prepare the dispenser. 3.1 3 3.2 ➋ ➋ ➊ • Remove ice entry cover plate ➊ • Remove bin thermostat capillary tube from bracket ➊ • Coil capillary tube and secure away from bin fill opening ➊ ➋ 3.3 3.4 ➊ ➊ ➋ ➋ • Remove retaining clips ➊ and deflector nuts ➋ 6 • Remove capillary tube bracket ➊ and deflector (Fig. 4.
3.5 3.6 ➋ ➌ ➊ ➊ ➋ • Mount cover plate/transport tube assembly • Insert end of ice transport tube (with retaining on outside of dispenser using screws, flat washers ➊, lock washers ➋ and nuts provided ❸ holes) through hole in center of cover plate assembly ➊ • Secure ice transport tube (holes) to retaining tabs on bracket 3.7 ➋ 3.
3.9 3.10 ➊ ➊ ➋ • Route thermostat capillary tube through mounting bracket grommets as shown ➊ • Insulate entire length of ice transport tube ➊ and route to icemaker in accordance with directions in Horizon installation instructions • Route bin signal wire to icemaker ➋ BEFORE PROCEEDING Prior to installing the louvered docking assembly, ensure that the drain fitting is oriented (right or left) correctly for your installation. An optional straight drain fitting is also supplied.
Install the louvered docking assembly. Louvered docking assembly 4 WARNING • Docking station must be secured in accordance with these instructions to ensure ice machine stability. • Ventilation openings in the louvered docking station should be clear of obstruction Wall bracket accessory • Mount louvered docking assembly to wall bracket accessory 4.
Undercounter installation detail Front View Top View Access panel/ door on counter 2" (51 mm) ➌ ➊ 2.25" (57 mm) ➍ 2" (51 mm) 24" x 15" cutout (610 mm x 381 mm) bottom of ice machine side of ice machine CAUTION • Keep ventilation openings in the appliance enclosure clear of obstruction. • To ensure proper ventilation (if not using supplied grille) carefully review air circulation specifications on facing page (4.1) 3D Counter View 31.25" min. (794 mm) 23.5" min. (597 mm) 24" min.
Ice transport tube Install the ice transport tube. 5.1 5 Ice transport tube installation. ➋ Hot Water 160 F (71 C) ➎ ➊ 1/4" ➌ 1' ➍ ➏ ➐ Ice transport tube tips • Insulate entire length of ice transport tube ➊ • Secure ice transport tube ➋ as needed to prevent dips and traps from forming. For long tube runs see guide on page 16. • Pitch tube at least 1/4" per foot (6,4mm/.
Bin signal Install the bin signal. 2.1 6.1 6 Bin Signal Installation ➏ ➎ ➐ Ground ➌ ➊ ➋ 16" (61 cm) ❹ • Mount the electrical box to the side of the dispenser ➊ to establish a ground connection. Note: If a 4 x 4 box is mounted to a non-grounded surface, connect ground wire at an appropriate ground. • Connect the bin signal cord to the plug on the electrical box.
External connections Connect utilities to louvered docking assembly. 7.1 Air-cooled ice machines only 7.2 7 Water-cooled ice machines only ➊ ➊ ➏ ➋ ➋ ➐ ➌ ➌ Minimum 8" radius ➏ Minimum 8" radius ➑ 2 ft. x 1" OD silicone tubing 2 ft. x 1" OD silicone tubing 3/4" barb x 3/4" FPT 3/4" barb x 3/4" FPT ➍ ➍ 3/4" MPT x 1" slip 3/4" MPT x 1" slip ➎1" Stand pipe/Drain • Rough-in ice machine potable water supply ➊.
Connect louvered docking assembly to ice machine. Internal connections 8 CAUTION • Plug must be accessible after final installation. Air-cooled ice machines – follow steps 8.1 through 8.5. 8.1 8.2 Ice transport tube Potable water and drain lines ➋ ➊ ➊ • Slide ice machine into louvered docking assembly ensuring that drain tube is fully seated on barbed drain fitting ➊ • Insert ice transport tube all the way into coupling and tighten nut firmly ➋ • Insert potable water line into valve 8.3 8.
Water-cooled ice machines – follow steps 8.6 through 8.12. 8.6 TDS switch Cooling lines CLEAN POWER ON HIGH LOW BIN MAKING ICE SLEEP CYCLE TIME DELAY LOW WATER MAINT/CLEAN SERVICE HIGH AMPS HIGH PRES TDS DRAIN CLOG CLEANER FULL 8.5 In LOW • Set the TDS switch on the electrical box: HIGH: for extended service life LOW: for low-scale water 8.7 • Install ice machine cooling water lines to louvered docking assembly 8.
8.9 8.10 Cooling lines and power Power cord ➋ ➊ • Remove twist tie • Carefully pass cord thru opening and plug into wall outlet • Connect cooling water lines to ice machine (Water "Out" connects to water regulator.) ➊ • Water valve is set at the factory. DO NOT remove seal or adjust water valve ➋ 8.12 Power cord TDS switch CLEAN POWER ON HIGH LOW BIN MAKING ICE SLEEP CYCLE TIME DELAY LOW WATER MAINT/CLEAN SERVICE HIGH AMPS HIGH PRES TDS DRAIN CLOG CLEANER FULL 8.
Front cover Install front cover to ice machine. 9 Install front cover Front cover installation – air-cooled undercounter only ➊ ➋ ➋ ➌ ➌ CAUTION • Keep ventilation openings in the appliance enclosure clear of obstruction. • To ensure proper ventilation (if not using supplied grille) carefully review air circulation specifications in section 4.
Long tube run recommendations max. 2 ft (.6m) ➋ ➊ 1/4" 1' • Pitch ice transport tube to allow melt water to drain towards ice machine ➊ • Secure insulated ice transport tube at least every 2 ft (.
Cornelius • RIDE Technology self-contained 19
801 Church Lane • Easton, PA 18040, USA Toll free (877) 612-5086 • +1 (610) 252-7301 www.follettice.
