Horizon Elite™ Ice Machine Models with RIDE™ Technology Installation Instructions for Ice Manager™ Diverter Valve HCC1010AMS, HCC1410AMS, HCC1010WMS, HCC1410WMS, (See model number configurator on page 2 for details.) Order parts online www.follettice.
Chewblet® Ice Machine Model Number Configurations HC Icemaker MC Maestro™ Chewblet® (400 Series) HC Horizon Chewblet (1000, 1400, 1650 Series) HM Horizon Micro Chewblet 2 Voltage C 1400 A Series 400 up to C 208-230/60/1 (icemaking head) Self-contained only. 454 lbs D 115/60/1 (icemaking head) (206kg) Self-contained and remote. If remote 1000/1010 unit, high side is 208-230/60/1. up to E 230/50/1 (icemaking head) 1036 lbs Self-contained only.
Horizon ice machine for use with Ice Manager diverter valve system The Ice Manager diverter valve system delivers ice to two ice storage units enabling a single Follett Horizon ice machine to meet demand for ice at two locations. The system’s sensors monitor ice levels in each storage unit and automatically switch ice delivery to the appropriate location. After thorough review of Ice Manager site survey, read and complete Horizon ice machine installation sections 1 through 6.
Carefully unpack and inspect the contents of your Follett ice machine. 1.
Site preparation Prepare the installation site. 2 Provide drainage, water supply and electrical power to within 6 feet (2m) of ice machine in accordance with local and national codes. Outdoor installation is not recommended and will void warranty. 2.1 2.
Install the louvered docking assembly. Louvered docking assembly 3 WARNING • Docking station must be secured in accordance with these instructions to ensure ice machine stability. • Ventilation openings in the louvered docking station should be clear of obstruction Wall bracket accessory • Mount louvered docking assembly to wall bracket accessory 3.
Undercounter installation detail – Horizon 1010 & 1410 series Front View Top View Access panel/ door on counter 2" (51 mm) ➌ ➊ 2.25" (57 mm) ➍ 2" (51 mm) 24" x 15" cutout (610 mm x 381 mm) bottom of ice machine side of ice machine CAUTION • Keep ventilation openings in the appliance enclosure clear of obstruction. • To ensure proper ventilation (if not using supplied grille) carefully review air circulation specifications on facing page (4.1) 3D Counter View 31.25" min. (794 mm) 23.5" min.
Ice transport tube Install the ice transport tube. 4.2 4 Ice transport tube installation. ➋ Hot Water 160 F (71 C) ➍ ➏ ➎ ➐ ➊ 1/4" ➌ 1' Ice transport tube tips • Insulate entire length of ice transport tube ➊ • Secure ice transport tube ➋ as needed to prevent dips and traps from forming. For long tube runs see guide on page 15. • Pitch ice transport tube at least 1/4" per foot (6,4mm/.
External connections Connect utilities to louvered docking assembly. 5.1 Air-cooled ice machines only 5.2 5 Water-cooled ice machines only ➋ ➋ ➌ ➍ ➊ ➌ ➎ • Remove access panel if necessary • Install drain line ➊. The rigid drain line from the ice machine must have at least 1/4" per foot pitch (6,4mm/0,3m). • Rough-in ice machine potable water supply ➋. 3/8” push-in connection will be made at shut-off valve inside machine.
Internal connections Connect louvered docking assembly to ice machine. 6 CAUTION • Plug must be accessible after final installation. Air-cooled ice machines – follow steps 6.1 through 6.5. 6.1 6.2 Ice transport tube Potable water and drain lines ➋ ➊ ➊ • Slide ice machine into louvered docking assembly ensuring that drain tube is fully seated on barbed drain fitting ➊ • Insert ice transport tube all the way into coupling and tighten nut firmly ➋ • Insert potable water line into valve 6.3 6.
Water-cooled ice machines – follow steps 6.6 through 6.12. 6.6 TDS switch Cooling lines CLEAN POWER ON HIGH LOW BIN MAKING ICE SLEEP CYCLE TIME DELAY LOW WATER MAINT/CLEAN SERVICE HIGH AMPS HIGH PRES TDS DRAIN CLOG CLEANER FULL 6.5 In Out LOW • Set the TDS switch on the electrical box: HIGH: for extended service life LOW: for low-scale water 6.7 • Install ice machine cooling water lines to louvered docking assembly 6.
6.9 6.10 Cooling lines and power Power cord ➋ ➊ • Remove twist tie • Carefully pass cord thru opening and plug into wall outlet • For H_E units, install a suitable plug • Connect cooling water lines to ice machine ➊ • Water valve is set at the factory. DO NOT remove seal or adjust water valve ➋ 6.12 Power cord TDS switch CLEAN POWER ON HIGH LOW BIN MAKING ICE SLEEP CYCLE TIME DELAY LOW WATER MAINT/CLEAN SERVICE HIGH AMPS HIGH PRES TDS DRAIN CLOG CLEANER FULL 6.
Front cover Install front cover to ice machine. 7 Install front cover Front cover installation – air-cooled undercounter only ➊ ➋ ➋ ➌ ➌ CAUTION • Keep ventilation openings in the appliance enclosure clear of obstruction. • To ensure proper ventilation (if not using supplied grille) carefully review air circulation specifications in section 4.
Long tube run recommendations max. 2 ft (.6m) ➋ ➊ 1/4" 1' • Pitch ice transport tube to allow melt water to drain towards ice machine ➊ • Secure insulated ice transport tube at least every 2 ft (.
ICE MANAGER self-contained 15
Horizon, Horizon Elite, Maestro, Harmony, Ice Manager, SafeCLEAN, Sani-Sponge, RIDE and Vision are trademarks of Follett Corporation. Chewblet is a registered trademark of Follett Corporation, registered in the US. 801 Church Lane • Easton, PA 18040, USA Toll free (877) 612-5086 • +1 (610) 252-7301 www.follettice.
