Horizon Elite™ Ice Machine Installation Instructions to Ice Storage Bin Top-mount Applications HCD/HMD710ABT, H_C1010ABT, H_C1010WBT, H_C1410ABT, H_C1410WBT, (See model number configurator on page 2 for details.) Order parts online www.follettice.com self-contained 801 Church Lane • Easton, PA 18040, USA Toll free (877) 612-5086 • +1 (610) 252-7301 www.follettice.
Chewblet® Ice Machine Model Number Configurations HC Icemaker MC Maestro™ Chewblet® (425 Series) HC Horizon Chewblet (710, 1010, 1410, 1810, 2110 Series) HM Horizon Micro Chewblet Voltage D 1810 A Series V S Application Configuration Vision™ Harmony™ Ice storage bin Drop-in Ice Manager diverter valve system P Cornelius Profile PR150 S RIDE™ (RIDE remote ice delivery equipment) T Top-mount Condenser 425 up to C 208-230/60/1 (icemaking head) Self-contained only.
Contents Unpack.............................................................................................................................................................................4 Unpack Ice Machine...................................................................................................................................................4 Site Preparation...........................................................................................................................................
1. Unpack Carefully unpack and inspect the contents of your Follett ice machine. 1.
2. Site Preparation Provide drainage, potable water supply and electrical power to within 6 feet (2m) of ice machine in accordance with local and national codes. Outdoor installation is not recommended and will void warranty. 2.1 Installation site requirements Minimum 8" radius 2 ft.
3. Louvered Docking Assembly Installation WARNING! §§ Prior to installing the louvered docking assembly, ensure that the drain fitting is oriented (right or left) correctly for your installation. An optional straight drain fitting is also supplied. You may need to remove the back panel of the docking assembly in order to re-orient or change the drain fitting. Replace back panel prior to mounting the docking assembly.
4. External Connections 4.1 Ice Transport Tube Installation Hot Water 160 F (71 C) ➋ ➊ ➌ §§ Install supplied ice transport tube insulation. §§ Heat end of transport tube in cup of 160 F (71 C) hot water to soften and spread with pliers ➊ before making connection to ease assembly. §§ Connect ice transport tube to coupling on louvered docking station ➋. §§ Connect ice transport tube to shuttle actuator ➌.
4.2 Air-cooled ice machines only 4.3 Water-cooled ice machines only ➊ ➊ ➏ ➋ ➋ ➐ ➌ ➌ ➏ Minimum 8" radius 2 ft. x 1" OD silicone tubing 2 ft. x 1" OD silicone tubing 3/4" barb x 3/4" FPT 3/4" barb x 3/4" FPT ➍ ➍ 3/4" MPT x 1" slip 3/4" MPT x 1" slip ➎ 1" Stand pipe/Drain ➎ 1" Stand pipe/Drain §§ Rough-in ice machine potable water supply ➊. 3/8" push-in connection will be made at shut-off valve inside machine §§ Remove access panel if necessary ➋.
5. Internal Connections Air-cooled ice machines – follow steps 5.1 and 5.5. Water-cooled ice machines – follow steps 5.6 through 5.12. 5.1 Ice transport tube 5.2 Potable water lines ➋ ➊ ➊ §§ Slide ice machine into louvered docking assembly ensuring that drain tube is fully seated on barbed drain fitting ➊. §§ Insert potable water line into valve ➊. §§ Insert ice transport tube all the way into coupling and tighten nut firmly ➋. 5.3 Power cord 5.4 Power cord §§ Remove twist tie.
5.5 TDS switch 5.6 Cooling Lines CLEAN POWER ON LOW BIN MAKING ICE SLEEP CYCLE TIME DELAY LOW WATER MAINT/CLEAN SERVICE HIGH AMPS HIGH PRES DRAIN CLOG TDS HIGH In LOW §§ Set the TDS switch on the elctrical box. –– HIGH: for extended service life –– LOW: for low-scale water 5.7 Ice transport tube Out §§ Install ice machine cooling water lines to louvered docking assembly. 5.
5.9 Cooling lines and power 5.10 Power cord ➋ ➊ §§ Remove twist tie. §§ Carefully pass plug thru opening and plug into wall outlet. §§ For H_E units, install a suitable plug. §§ Connect cooling water lines to ice machine ➊. (Water "Out" connects to water regulator.) §§ Water valve is set at the factory. DO NOT remove seal or adjust water valve ➋. 5.
6. Front Cover Install front cover to ice machine. ➊ ➋ §§ Slide ice machine cover over machine, ensuring that tabs on back of cover slip under louvers on back of louvered docking assembly ➊, then tighten two screws through cover. §§ Place louvered front cover on machine ➋. 7. Ice machine start up procedure The start-up procedure below is intended to ensure that ice machine is operating properly after installation has been made.
