Ice•DevIce™ Ice Management Systems Order parts online www.follettice.com Installation, Operation & Parts Manual Ice•DevIce with SmartCART™ 75 801 Church Lane • Easton, PA 18040, USA Toll free (877) 612-5086 • +1 (610) 252-7301 www.follettice.
Contents Welcome to Follett. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Before you begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Product descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Welcome to Follett Follett ice storage bins enjoy a well-deserved reputation for excellent performance, long-term reliability and outstanding labor-saving and sanitation benefits. To ensure that your ice management system delivers this same degree of service, please read this manual carefully before installing or operating the system. If you have any questions or require technical help at any point, please call our technical service group at (877) 612-5086, or +1 (610) 252-7301.
DEV _ _ _ _ SG-_ _-75 Ice•DevIce with SmartCART 75: • Ice storage bin • 24" (610mm) high base • 8" (203mm) plastic ice chute • Ice cart with three Totes ice carriers • Ice probe and rake tools ! DEV _ _ _ _ SG-_ _-125 Ice•DevIce with SmartCART 125: • Ice storage bin • 24" (610mm) high base • 4" (102mm) plastic ice chute • Insulated plastic ice transport cart with hinged lid • Ice probe and rake tools DEV _ _ _ _ SG-_ _-ICS125 Ice•DevIce with Cambro ICS125L: • Ice storage bin • 24" (610mm) high base • 4"
Installation If unit does not fit through door, lower door assembly can be removed (see steps A and B below). If door removal is not necessary, proceed to step C. A. Removing lower door assembly (if needed) 1. With lower access door closed remove Phillips head screw and washer from hinge on each side of lower access door. 2. Insert screwdriver between door and hinge bracket on one side of door and gently push against bracket to provide room for door stud to clear bracket. 3. Remove access door. 4.
C. Installing base section (Ice•DevIce models with SmartCART 75, 125, Cambro* ICS125, bagger accessory or correctional package) 1. Remove screws holding base to skid and remove skid. 2. Position base in intended position and adjust feet to level in both directions. 3. For models with SmartCART 75: Adjust feet and level base so that there is no interference between base and cart when cart is rolled under base with lid closed. 4. Mark position of each flanged foot anchoring hole. 5.
! 11. 12. 13. 14. 15. Follow Steps 11 - 15 to anchor upper and lower sections of all two-section upright bins. Brackets must be installed to avoid possible injury should unit move. Lower upper section onto lower section, taking care not to disturb gasketing material and sealant beads. Remove protective covering from stainless steel surfaces. Install icemaker according to manufacturer’s instructions.
G. Installing 8" (204mm) plastic chute Fig. 4 (for Ice•DevIce models with SmartCART 75, COR package) 1. Orient stainless chute bracket with open end of bracket tabs facing down. 2. Insert supplied 1/2" 1/4-20 carriage head bolts through bracket and base and hand tighten only. 3. Gently push on sides of plastic chute to fit inside bracket, inserting bracket tabs into slots in plastic chute. 4. Push up on plastic chute to align holes and secure with supplied thumbscrew. 5.
Bin operation General operation of unit Ice in the hopper section of the ice management system falls through the ice chute in front of the bin and into the cart, Totes ice carrier or bag when the chute gate is pulled up. The flow of ice is stopped by pushing down on the chute gate. The SmartGATE restricts the flow of ice into the hopper area and can be adjusted and locked at one of several levels to accommodate the flow characteristics of different types of ice.
Using tools Two tools — a paddle and a rake — ship with the Ice•DevIce and should be mounted for easy access on either side of the bin in the bracket provided. Using paddle If there is adequate ice in Ice•DevIce but hopper is not filled with ice, it may be that ice has congealed behind SmartGATE and cannot flow into hopper. This can often be remedied by simply opening and closing SmartGATE several times (see adjusting SmartGATE, above.
Assembly, operation and cleaning of Ice•DevIce carts and accessories The following assembly, operation and cleaning instructions have been divided into five parts. Use the section pertaining to the carts and accessories purchased with your Ice•DevIce unit. SmartCART 75 Assembly 1. Remove installation hardware from poly bag taped to Totes ice carrier. 2. Place cart handle ends along holes at the back of cart base. Align handle end holes with small holes in sides of cart. 3. Tighten bolts securely. 4.
Filling Totes ice carriers 1. Lift lid. Position ice carrier closest to cart handle under ice chute. 2. Open lift door and confirm there is ample ice in hopper area. If not, see previous sections on adjusting SmartGATE and using tools.) 3. Pull chute gate up to start flow of ice into ice carrier. 4. When ice carrier is almost full, push chute gate down to stop flow. (Some ice will continue to fall as chute gate closes. Leave room in ice carrier for this in-flight ice to avoid spillage.) 5.
SmartCART 125 Assembly The cart will arrive to you fully assembled. Check that the drip shelf inside the cart is horizontal, with the hole oriented toward the front. Operation 1. The cart is highly maneuverable with two swivel casters in front. 2. The polyethylene construction is resistant to damage from normal use, and prevents it from marring walls and fixtures. 3. A hand valve at the front of the cart allows melt water or cleaning solutions to be easily drained from the cart.
Cambro ICS125L Cart Assembly The cart will arrive to you fully assembled. Check that the drip shelf inside the cart is horizontal, with the hole oriented toward the front. Operation 1. The cart is highly maneuverable with two swivel casters in front. 2. The polyethylene construction is resistant to damage from normal use, and prevents it from marring walls and fixtures. 3. A hand valve at the front of the cart allows melt water or cleaning solutions to be easily drained from the cart.
Bagger Accessory Assembly 1. Attach tape dispenser to left side of bagger assembly for right-handed users using two screws provided. For left-handed users, attach to right side. 2. Center tape roll on tape drum Fig. 7, as shown, to dispense tape with adhesive side up. 3. Place tape drum with tape in slot Fig. 8 and pull tape lead end forward to front edge of bag sealer. Fig.
Totes ice carrier for low-profile Ice•DevIce unit Assembly The Totes ice carrier requires no assembly. Operation 1. The polyethylene construction of the ice carrier makes it light and very resistant to damage from normal use. 2. The handle makes it convenient to transport up to 25 lbs (11.34kg) of ice and the shape of the ice carrier makes pouring easy. Filling Totes ice carrier 1. Position ice carrier under ice chute. 2. Open lift door and confirm there is enough ice in hopper area.
Replacement parts Bin replacement parts 4 1 3 2 5 7 8 6 9 Part # 502176 502177 502180 502218 502237 502264 501100 502373 502554 502374 502555 502281 502556 502196 502639 502952 502872 502557 502064 00109538 Description Door, outer lift, 28" (686mm), (includes door hinges and hardware) Door, outer lift, 45" (1067mm), (includes door hinges and hardware) Hinges, pair (includes mounting hardware) Retainer, SmartGATE (includes shoulder screw) (2) Inspection windows 21.125" x 8.
Bin door replacement parts 5 2 1 3 8 7 4 Part # Description Reference number 502178 Hinge assembly, left-hand (mounts to lift door) 1 502179 Hinge assembly, right-hand (mounts to lift door) Not shown 502185 Locking catch, SmartGATE (includes shoulder screw) 2 01161074 Ice chute gate, 28" (712mm) wide door 3 01161082 Ice chute gate, 45" (1143mm) wide door 3 502367 SmartGATE, 28" (712mm) wide door 4 502363 SmartGATE, 45" (1143mm) wide door 4 502176 Lift door, 28" (712mm) wide (includes 502178
COR accessory package replacement parts – Ice•DevIce with elevated base for correctional facilities Part # Description Reference number 00111377 45” poly door prison package Not shown 00111385 28” poly door prison package Not shown 00111393 Door, upper lock bracket (left and right set) Not shown 00111401 End panel prison package (left and right set) Not shown SmartCART 75 replacement parts (stainless drain tray base) 1 5 4 2 3 8 7 6 Part # Description Reference number 502197 Handle, ca
New SmartCART 75 replacement parts (roto-molded drain tray base) 2 1 10 9 3 4 7 5 6 8 Part # Description Reference number 00115634 Handle with hardware 1 00115642 Lid with hardware 2 502204 Stud, pivot (1 pair), cart lid 3 00115659 Drain assembly, cart 4 00115667 Axle with cotter pins and washers 5 00115683 Plate, axle (2 required) 6 00134908 6" wheel with cotter pin and washer 7 502569 Wheel, front of cart 8 502263 Totes ice carrier, non draining (one) 9 502097 Handle, Totes ice carrier 1
Rejestracja gwarancji i ocena sprzętu Dziękujemy za zakup urządzenia firmy Follett. Mamy nadzieję, że nasze urządzenia spełniają i przekraczają Państwa oczekiwania, gdyż naszym celem jest dostarczenie klientom wysoce wartościowych produktów i usług, zasługujących na ich pełne uznanie. Prosimy zapoznać się z załączoną instrukcją instalacji i obsługi. Istotne jest przeprowadzenie instalacji zgodnie z wymogami producenta, co zapewni działanie urządzenia z maksymalną wydajnością.
Garantieregistrierung und Produktbeurteilung sind wichtig, damit wir einen Überblick über unsere Produkte behalten und ihre Effizienz bewerten können. Wir möchten Sie bitten, Garantien für Follett-Produkte auf unserer Website www.follettice.com/support zu registrieren und den Punkt „Garantieregistrierung und Produktbeurteilung” zu wählen. Es ist ganz einfach. Nehmen Sie sich bitte einen Moment Zeit, um die Registrierung heute vorzunehmen.
Registratie van garanties en beoordeling van apparatuur Gefeliciteerd met uw aankoop van Follett ®-apparatuur. We hopen dat onze apparatuur uw verwachtingen invult of zelfs overstijgt, omdat we ernaar streven om hoogwaardige producten en diensten te leveren die u uitermate tevreden stellen! Lees de bijgevoegde installatie- en bedieningshandleiding zorgvuldig door. Het is belangrijk dat de installatie uitgevoerd wordt volgens de fabrieksspecificaties, zodat uw apparatuur zo efficiënt mogelijk werkt.
