Spec Sheet

Double door Ice•DevIce
2320-201912 | © Follett LLC
Specification
Maximum bin capacity  see model table below
W1 Bin width 72.00" (182.9 cm)
D1 Bin depth  see model table below
D2 Bin depth with door fully
extended
add 18.50" (47.0 cm) to D1
H1 Bin height  (adjustable) see model table below
H2 Bin base height (adjustable) 24.75" (62.9 cm)
H3 Bin base clearance (adjustable) 21.62" (54.9 cm)
Required door access  see model table below
W2 Cart width 21.50" (54.6 cm)
D3 Cart depth 34.00" (86.4 cm)
H4 Cart height at front edge 20.50" (52.1 cm)
H5 Cart height with lid up 38.62" (98.1 cm)
L1 Drain  1.00" FPT, center of bin bottom
(drain elbow supplied)
Dispense rate up to 5 lb (2.3 kg) per second
Ice compatibility cube ice and Chewblet ice
Approximate ship weight see model table below
NOTE: For indoor use only
SHORT FORM SPECIFICATION:
Ice•DevIce system to be Follett model _________ elevated
bin, base and cart system with front ice chute and industry-exclusive SmartGATE ice shield. Bin to
hold approximately ______ lb (kg) of ice. Exterior finish of bin and base to be full stainless front,
sides, back and bottom. Bin liner on all models to be heavy-duty, non-corroding polyethylene.
Bin liner to have non-corroding polyethylene walls and stainless steel bottom. Bin insulation to
be CARB compliant non-HFC foam. Bin top to be stainless and custom-cut for ice machine(s) to
be used. Lower door assembly to include non-corroding polyethylene ice access door assembly,
polyethylene lift door with PowerHinge door hinge to eliminate gaskets and latches, and inner
SmartGATE ice shield to positively control ice flow into ice access door assembly area. Entire lower
door assembly to be easily removable for installation through narrow doors. Where used, upper
inspection windows to be molded double-wall plastic to increase durability while minimizing
meltage and condensation. All models to be equipped with flanged, adjustable feet, paddle and
rake tool set. NSF-listed.
Dimensional drawing
H5
D3
L1
C
L
C
L
H3
H4
H2
D2
H1
D1
W2
W1
DEV2100,
DEV2250,
DEV2650
DEV3200,
DEV3900,
DEV4600
Model
with
SC75
cart
with
SC125
cart
with
Cambro
cart
with
bagger kit
Maximum
bin capacity
lb (kg) 
Cubic volume
cu ft (m)
Depth  - D1
in (cm)
Height  - H1
in (cm)
Required door
access 
in (cm)
Approximate
ship weight
lb (kg)
DEV2100SG-72 -75 -125 -ICS125L
-BG
2110 ( 957) 67.1 (1.90)
40.00 (101.6) 75.50 (191.8) 41.00 (104.1) 841 (381)
DEV2250SG-72 -75 -125 -ICS125L
-BG
2250 (1021) 71.5 (2.02)
48.00 (121.9) 69.50 (176.5) 46.00 (116.8) 863 (344)
DEV2650SG-72 -75 -125 -ICS125L
-BG
2650 (1202) 84.0 (2.38)
40.00 (101.6) 85.50 (217.2) 41.00 (104.1) 943 (428)
DEV3200SG-72 -75 -125 -ICS125L
-BG
3240 (1470) 102.7 (2.90)
48.00 (121.9) 88.50 (224.8) 35.00 (88.9) 1144 (519)
DEV3900SG-72 -75 -125 -ICS125L
-BG
3940 (1787) 125.1 (3.54)
48.00 (121.9) 100.50 (255.3) 44.00 (111.8) 1263 (573)
DEV4600SG-72 -75 -125 -ICS125L
-BG
4640 (2105) 147.4 (4.17)
48.00 (121.9) 112.00 (284.5) 47.00 (119.4) 1276 (579)
Notes:
 Computed on cubic volume of bin. Does not reflect cart capacity or voids that can occur due to pyramiding.
 Add 8.00" (20.32 cm) to depth (D) for lower door assembly (easily removed for installation access).
 Special top required for ice machines weighing more than 1000 lb (454 kg). Add 2.12" (5.38 cm) to height. Contact factory.
 Required clearance for installation access through doors (may require removal of door assembly).
 Follett recommends installation of a floor drain with grate with all ice storage bins. Consider cart positioning when locating the drain.
Clearance required to pull cart from below bin — minimum 36.00" (91.4 cm), optimal 40.00" (101.6 cm).
Follett Europe Polska Sp. z o.o.
Mokry Dwór 26C 83-021 Wiślina, Poland
[phone] | Fax: [phone]
folletteurope.com
801 Church Lane | Easton, PA 18040, USA
1.610.252.7301 | Fax: [phone] | follettice.com
ICE•DEVICE, POWERHINGE, SMARTCART and TOTES are trademarks of Follett LLC.
CHEWBLET, FOLLETT and SMARTGATE are registered trademarks of Follett LLC, registered in the US.
Follett reserves the right to change specifications at any time without obligation. Certifications may vary
depending on country of origin.