User's Instructions

Standby Button:
When powering up for the first
time, press the “on/off switch” on
the fire. The default parameters of
the system are: the heating gear
position is “82°F/27°C”, the main
flame gear position is L1 (Orange),
no heating.
Changing Flame Effect:
In the power-on state, press this
button, the digital screen displays
the flame position and the flame
indicator is bright, and the main
flame position can be adjusted.
The flame brightness settings are:
F1, F2, F3, F4, Set as follows:
Button Display Flame Effect
1st
Press
F1 Full
2nd
Press
F2 Medium
3rd
Press
F3 Low
4th
Press
F4
Cycle
through
settings
Heating Operations:
1) Press the heater button to turn
the heating function on and off and
adjust the temperature setting.
Heater is divided into temperature
settings: 62°, 63°, 64°, 65°, 66°,
67F, 68°, 69°, 70°, 71°, 72, 73°,
74°, 75°, 76°, 77°, 78°, 79°, 80°,
81°, 82°F, ON. (Circular operation
control)
2) Press and hold the heater
button for 3 seconds to convert
the temperature unit from °C to °F.
The temperature display window
will flash. After the temperature is
set, the display unit will flash 5
times, then automatically saves
the settings and exits the setting
state. After the display unit is
turned on, if there is no operation
within 10 seconds, the setting
status is also exited.
3) Fan delay function: After the
appliance is turned off, the fan will
continue running for 15 seconds
then stop.
Open Window Detection function:
When the appliance is heating, the
ambient temperature suddenly
drops ≥–5°C within 10 minutes,
and the environment cannot be
warmed up within 30 minutes.
The appliance will automatically
display “OP”. The heating function
will be automatically turned off,
and when the “OP” is displayed, it
can be turned off and then
restarted by turning off and on the
appliance to clear the fault code.
4) This appliance has a non-self-
resetting overheat protection
device (thermal cut-out) which will
activate if the air inlets or outlets
are obstructed. For safety reasons
the fire will NOT switch on again
automatically, the following
procedure must be carried out
before the fire can be operated.
NOTE: The flame-effect will remain operational
if the cut-out is activated, only the fan heater is
prevented from working.
Switch OFF the appliance at the
wall socket or outlet. Leave the fire
OFF for a period of no less than 10
minutes, ensuring all obstructions
are removed. Switch the appliance
ON at the wall. Ensure the
appliance is turned ON at the
control switches. If the fire fails to
operate correctly, repeat the
above procedure.
Fuel Bed Options:
Once powered, press the “Fuel
Bed” button and the LCD screen
on the remote will display the fuel
bed icon. Now, the fuel bed colour
can be adjusted. The different
settings are: L1, L2, L3, L4; Fuel
bed light. Set as follows:
Button Display Flame Effect
1st
Press
L1 Orange
2nd
Press
L2 Blue
3rd
Press
L3
Orange +
Blue
4th
Press
L4
Cycle
through
settings
Setting Sleep Timer:
In the timed display, press the
“Sleep Timer” button to adjust the
time, plus one hour for each press.
(You can’t enter the weekly timing
selection, you can only set the
current automatic shutdown time.
This function is available when the
weekly timing function is turned on.
Will not operate). Timing range:
1H, 2H, 3H, 4H, 5H, 6H, 7H, 8H,
9H, OF, 1H (cycle adjustment).
Control Down Lighting:
Turns the down lighting lights on
and off.
Setting Clock and Timer:
Use the date button to choose
from Monday to Sunday or week
timer mode option. Option mode:
1-2-3-4-5-6-7-A-oF.
Clock setting:
1) At standby state (after the unit
is plugged in and before pressing
“main power”), press and hold the
Setting button on the remote for 3
seconds, the digital display will the
flash “00:00”.
2) Press on the remote control
to set the hour, press the remote
control to set the minutes.
3) Press “Setting” to enter the
setting of the week timer. Press
to select Sunday to Saturday,
The date symbol will be light up
after the day is selected. When
finished, press the button to
exit setting.
4) The current clock must be set
after the initial power-on or power-
off, otherwise the clock will remain
“00:00” status and you won’t be
able to set the week timer function.
// 12.0 OPERATING THE APPLIANCE
Continued
// 23
// 24© 2020 British Fires