F200 PRO User Guide This product records videos while the vehicle is operating. Read and follow the instructions in this guide to properly use and maintain the product.
Before using the product About the product This product records videos while the vehicle is operating. Use this product only for reference when investigating incidents or road accidents. This product is not guaranteed to record and cloud service for ALL events. The device may not properly record accidents with small impacts that are too minor to activate the impact sensor or accidents with massive impacts that cause the vehicle’s battery voltage to deviate.
FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Avant d’utiliser le produit À propos de ce produit Ce produit enregistre des vidéos pendant le fonctionnement du véhicule. Utilisez cet appareil seulement à des fins de documentation pour les enquêtes d’incidents ou d’accidents de la route. Il n’existe aucune garantie que ce produit enregistrera ou effectuera le traitement des données en nuage pour tous les événements.
Cet équipement a été testé et déclaré conforme aux limites pour appareils numériques de classe B, selon la section 15 des Règles de la FCC. Ces limites sont destinées à assurer une protection raisonnable contre les interférences nuisibles dans une installation résidentielle. Cet équipement génère, utilise et émet de l’énergie de fréquences radio et peut, en cas d’installation ou d’utilisation non conforme aux instructions, engendrer des interférences nuisibles pour les communications radio.
Contents Safety information 5 1. Product overview 8 1.1 Included items 8 5. Using the PC viewer 21 5.1 System requirements 21 5.2 PC viewer for Windows 21 5.2.1 Installing the PC viewer (for Windows) 21 1.1.1 Standard items 8 5.2.2 PC viewer screen layout (for Windows) 22 1.1.2 Accessories (sold separately) 8 9 5.2.3 Playing recorded videos on the PC viewer (for Windows) 23 1.2.1 Front camera (main unit) - front view 9 5.2.4 PC viewer screen layout (for Mac) 24 1.2.
Safety information Read the following safety information to properly use the product. Safety symbols in this guide "Warning" - Indicates a potential hazard which, if not avoided, may result in injury or death. "Caution" - Indicates a potential hazard which, if not avoided, may result in minor injury or property damage. "Note" - Provides useful information to help users better utilize the product's features.
Power supply • Do not operate or handle the power cable with wet hands. Doing so may result in electrocution. • Do not use damaged power cables. Doing so may result in electrical fire or electrocution. • Keep the power cable away from all heat sources. Failure to do so may cause the power cord insulation to melt, resulting in electrical fire or electrocution. • Use the power cable with the correct connector and make sure the power cable is connected securely and is firmly in place.
Other information about the product Product management and operation • Do not expose the product to direct sunlight or intense light. The lens or internal circuitry may fail otherwise. • Use the product at a temperature between 14°F and 140°F (-10°C to 60°C) and store the product at a temperature between -4°F and 158°F (-20°C to 70°C). The product may not function as designed and some permanent physical damages may result if it is operated or stored out of the specified temperature ranges.
1. Product overview 1.1 Included items Ensure that all the items are included when you open the product box. 1.1.1 Standard items Front camera (main unit) Mount Car charger Adhesive cable holder MicroSD memory card with adapter (consumable) Quick start guide & Warranty / CS information / User guide (stored in the microSD card) The standard items may change without prior notice. 1.1.
Product overview 1.2 Part names 1.2.1 Front camera (main unit) - front view Mount connector Used to connect the mount. DC-IN power port Used to connect the power cable. GPS port Used to connect the external GPS receiver (optional). Front camera lens Records the front view. V-IN input port Used to connect the rear camera (optional). Speaker Outputs the voice guide and buzzer sounds to indicate the product’s status. 1.2.
Product overview 1.2.3 Rear camera (optional) Adhesive mount Used to fix the rear camera in the vehicle. Connection port Used to connect the rear camera to the front camera using a rear camera cable. Rear camera lens Records the rear view. Security LED Indicates that the video is being recorded. 1.3 Removing and inserting the memory card Follow the instructions to remove the memory card from the product or to insert the memory card into the product.
2. Installing the product 2.1 Installing the front camera (main unit) Follow the instructions to properly install the product. 2.1.1 Selecting an installation location Select an installation location that can record the entire view in front of the vehicle without obstructing the driver’s vision. Ensure that the front camera lens is located in the center of the windshield.
Installing the product 3 Remove the protective film from the adhesive mount, and then press the mount to the installation location. ➊ 1 2 ➋ 4 1 ➊ 5 ➋2 Remove the product from the mount and push the mount against the windshield to ensure that the mount is firmly fixed. Align the product to the mount, and then slide it into the locking position until you hear a click. • The product may fall and be damaged during vehicle operation if it is not firmly fixed to the mount.
Installing the product 2.1.3 Connecting the power cable When the engine and electrical accessories are turned off, connect the car charger. Connect the cigar socket power cable to the product’s DC-IN power connector and insert the cigar jack into the vehicle’s power socket. ➊ • The hardwiring cable (optional) must be professionally installed to the vehicle by a trained mechanic. • The location and specifications of the power socket may differ by vehicle make and model.
Installing the product 2.2.2 Securing the rear camera Refer to the following instructions to secure the product to the installation location. 1 After determining the installation location, wipe the installation surface of the windshield with a dry cloth. Check the installation location before you secure the rear camera to the rear windshield. After securing the rear camera to the windshield, it is hard to remove the camera or change the installation location due to the strong adhesive.
Installing the product 2.2.3 Connecting the rear camera cable Power off the product and connect the rear camera cable to the front camera (main unit). 1 Connect one end of the rear camera cable to the front camera’s V-IN port. 2 Connect the other end of the rear camera cable to the rear camera's connection port. For safe driving, arrange the cables to prevent the driver's vision from being obstructed or interfering with driving.
3. Using recording features 3.1 Turning the product on or off The product is turned on automatically and continuous recording starts when you turn on the ACC or start the engine. Wait until the product is completely booted up after turning it on, and then begin operating the vehicle. The video recording does not begin until the product is completely turned on (booted up). 3.2 Learning about file storage locations Videos are stored in the following folders according to their recording mode.
Using recording features 3.3 Using the continuous recording feature Connect the power cable to the product’s DC-IN power port and then turn on the vehicle’s electrical accessories or start the engine. The status LED and the voice guide are turned on, and the continuous recording starts. During continuous recording, the product operates as follows. Mode Operation description STATUS LED Continuous recording During driving, videos are recorded in 1 minute segments and stored in the "cont_rec" folder.
Using recording features • Parking mode operates only when the hardwiring cable is connected. The hardwiring cable (optional) must be professionally installed to the vehicle by a trained mechanic. • To use all recording modes, insert a memory card into the product. • Depending on the battery charging status of the vehicle, the duration of parking mode may differ. If you want to use parking mode for an extended period, check the battery level to prevent battery depletion.
Using recording features 3.6 Using the Super Night Vision 2.0 With the Super Night Vision 2.0 feature, you can record videos that are much brighter than videos recorded without this feature. This feature is enabled by real-time image signal processing (ISP) to improve the brightness of recorded videos while parking at night. 3.
4. Using the mobile viewer You can view and manage recorded videos and configure various product features on your smartphone. • One of the following environments is required to use the THINKWARE DASH CAM LINK application: - Android 7.0 (Nougat) or higher - iOS 11.4 or higher • The Wi-Fi password is required when you connect the product to a smartphone for the first time. Enter “123456789” in the password input field. 4.
5. Using the PC viewer You can view and manage the recorded videos and configure various product features on your PC. 5.1 System requirements The following are the system requirements for running the PC viewer. • Processor: Intel Core i5, or higher • Memory: 4 GB or more • Operating system: Windows 7 or later (64-bit is recommended), macOS X10.8 Mountain Lion or later • Other: DirectX 9.0 or higher / Microsoft Explorer version 7.
Using the PC viewer 5.2.2 PC viewer screen layout (for Windows) The following provides brief information about the PC viewer's screen layout. ➋ ➍ ➌ ➎ ➊ ➏ ➐ ➑ ➒ ➓ Number ➊ ➋ ➌ ➍ ➎ ➏ ➐ ➑ ➒ ➓ 22 Description Open a file, or save a video with a different name. View or configure the dash cam settings, and set the language for the PC viewer. Display the current video in full screen. Tap the Back ( ) button to return to the previous screen.
Using the PC viewer 5.2.3 Playing recorded videos on the PC viewer (for Windows) Follow the instructions to play recorded videos. 1 Turn off the product and remove the memory card. 2 Insert the memory card into a memory card reader connected to your PC. 3 Double-click the shortcut to the PC viewer ( ) to open the program. The video files in the memory card will be automatically added to the playlist in the bottom-right corner of the PC viewer screen. The playlist section layout is as follows.
Using the PC viewer 5.2.4 PC viewer screen layout (for Mac) The following provides brief information about the PC viewer's screen layout. ➊ ➋ ➌ ➍ ➎ ➏ ➐ ➑ ➒ Number ➊ ➋ ➌ ➍ ➎ ➏ ➐ ➑ ➒ ➓ 24 ➓ Description Set the language for the PC viewer. Set the speed unit. Switch between the front and rear videos. View or configure the dash cam settings. Save the current scene. Print the current scene. Displays the current rear video. Displays the map screen.
Using the PC viewer 5.2.5 Playing recorded videos on the PC viewer (for Mac) Follow the instructions to play recorded videos. 1 Turn off the product and remove the memory card. 2 Insert the memory card into your Mac using a SD card reader or SD card adapter provided. 3 Open the PC viewer. 4 Click and locate the memory card. The video files in the memory card will be automatically added to the playlist in the bottom-right corner of the PC viewer screen. The playlist section layout is as follows.
6. Settings You can set the product features according to your needs and preferences using the mobile viewer or the PC viewer. The following procedures are based on the mobile viewer. The product will stop recording while configuring settings on the mobile viewer. 6.1 Managing the memory card From the mobile viewer, tap Dash Cam settings > Memory Card Settings to manage the memory card settings.
Settings Options Description Motion Detection Sensitivity Select from Lowest/Low/Mid/High/ Highest for the motion detection mode sensitivity. Record Timer Select from Disabled/3hrs/6hrs/12hrs/24hrs/48hrs/72hrs for the record time. Battery Protection Select from Enabled/Disabled for the battery protection. Battery cutoff voltage Select from 12V (11.6-12.3)/24V (23.2-24.6) for the battery cutoff voltage. Wintertime Battery Protection Select the month(s) to apply the battery protection feature.
Settings 6.5 Configuring the system settings From the mobile viewer, tap Dash Cam Settings > System Settings to configure the hardware system settings. Options Description Language Select the desired language. Volume Select the desired volume level for each feature (Safety Cameras/ADAS/System). Time Zone Select the desired time zone. Date / Time Select the date and time. To apply the current date and time on your smartphone to the dash cam, tap Get Current Time.
7. Accessing the product information New users may benefit from the basic product information that can be accessed from the Menu screen. 7.1 Viewing the product information From the mobile viewer, tap Dash Cam Info to view product information. The following product information will be displayed on the screen. • Model Name • Firmware Ver. • Safety Camera Ver. • Memory Size • LOCAL ID • GPS Info 7.
8. Upgrading the firmware A firmware upgrade is provided to enhance the product's features, operation or to increase stability. For optimal operation of the product, ensure that you keep the firmware up to date. Follow the instructions to upgrade the firmware. 1 On your PC, open a web browser and go to http://www.thinkware.com/Support/Download. 2 Select the product and download the latest firmware upgrade file. 3 Unzip the downloaded file. 4 Disconnect power to the product and remove the memory card.
9. Troubleshooting The following table lists the problems users may encounter while using the product and measures to resolve them. If the problem persists after taking the measures provided in the table, contact the customer service center. Problems Cannot power on the product Solution • Make sure the power cable (the car charger or the hardwiring cable) is connected to the vehicle and the product properly. • Check the vehicle’s battery level. The voice guide and/or buzzer do not sound.
10. Specifications To see the product specifications, refer to the following table. Item Specification Remarks Model name F200 PRO Dimensions / Weight 98.
http://www.thinkware.com Ver. 1.0 (July.
