WARNING: Read the ENTIRE instruction manual lo become familiar twilit the allure ol the product Galore operating, Allure to operate Hie product correctly can readily in damage fa ihe product, personal property and cause serious injury This isa sophisticated hobby product and NOT alloy li must be paralleled with ration and common sense snd requires some basic mechanical ability Allure to operate this Produced na safe and responsible manner could result in injury or damage La the protrude or other property, T
Table of Contents BOBBI .coouvmuim NE 3 Introduction and History 3 Contents of 4 Additional Required BMS. sss 5 Assembly Instructions... nnn 5 Generic Binding Instructions... 12 ESC min 12 Control Surfaces...cuumnunummmsssmsmsmsss sas 13 Final Assembly, Detailing, and Propeller 15 canter of Gravitation ee 17 Pr-flight Checklist... 18 I 18 Daily Flight 18 Spare parts list content...
Contents of Kit Before assembly, please inspect the contents of he kit The polo below details the contents of the kit and labels the major components "A Thea "07 Tor our convenience, | any parts are missing or decisive please identically the name or par number (refer to the state pars earnest ihe and of the manual. then contact the BMS Team: FMS Team Product Support AIF. Building B. 3rd Industry Zone, Mating, Tangshan Town, Guangdong City, FRC. Phone.
Connect the aileron control rod linkages 1 3) Shiva the provided piece df fuel Why aver the pontoon fod Linkage gai then nse the control rod linkage Thea the dosed idle in tie glean servo ian lg. 3) Mole: Fora single dale Paramilitary uae the fired hole to peaches a hind rate setting: Use the hind hole nearest Ihe sere ts lieutenant a ow tale sailing. i= A) Press the hole In the cavils over the end of the corolla rod linkage.
Install the Wing DT) Locate the fuselage C7 remove the dandelion Wr the fuselage over so the bot lam sides placings (io TL ZB) Begin th install the wing By guiding the Serbs leads hil the Deadpanning [0 the Gotta of the fuselage as vou lower the wing into position tho 8), in? fig 8 fn need the roger on the lading edo side of the Wind vita tha both I he fuselage dia Continue to guide the servo leads tha the opening in the fuselage by dulling on than om the canny side of the Juliana as vou fully seat the wing
iL ful By in Install the horizontal stabilizer © 11) Ovate the eft ball of the horizontal stabilizer 'E7. Align the notch the slenderize with the plastic lounge protruding from the fuselage.
0 48: Press the noel sie stabilizer nia place tha 1050 163 Tum the fuselage over Secure the horizontal stabilizer wile the two supped screws frat bag Hg 16 UT Conn act the 100 and rig elevator surfaces by ingraining the provided screw from bag "Has shown (fg.
Connect the elevator control rod linkages 1 18] Press the stickleback inked connectors over the corresponding ball end on the control Host located on the underside of the sleepwalker (Bg 18) Receiver Connection dO Connect he labeled leads pad tha red alias Connection diagram ig 18.
Install the battery C2 pine the balladry inch the ballet compartment as shown (lg.
Center of Gravity Before balancing your model, naked sire the i is completely assembled, the battery 1s installed, and the retractable landing bear sin the lowered position. The reprimanded cellar of gravy (CG) for your model is 45-50 mm from the wings leading edge (measured at point of contact with fuselage). Lightly mark he ideal center of gravity positioning he lop surface of the wing on each side of the fuselage.
BH 101 Fuselage Ei 102 Main wing set Eid 103 Horizontal stabilizer F104 Cockpit EH 105 Bonner EH 106 Propeller 1 10 577 Blade) EH 107 Ol Tank EH 108 Machine Gun FH 100 Spearhead Head FH 110 Exhaust Pipe EH 111 Motor Mount FH 112 Motor Board FH 113 Main banding Rear System (A whole set with retrace, strut and tires) FH 114 Hear Landing Gear Bel FHS The inner fairing door Eb 116 Motor Shalt EH 117 Linkage Hod EH 118 Borax Sel EH 1149 Decal Shes EH 120 Pigeon elevation) EH 121 LED BH I122 Lamp Cover ERS Motor
ESC instruction Wires Connection: The electronics speed controller can be connected to the motor by soldering directly or with high quality connectors Always use new connections, which should be soldered carefully 1o the cables and insulated with heat shrink tube. The maximum length of the battery pack wires shall be within 6 inches ® Solder controller to the motor wires, @ Solder appropriate connectors to the battery wires ® Insulate all spider connectors with heat shrink tubes.
Cur ESC allows vou to program parameters 1o fit your specific needs: User programmable brake selling we recommend using brake Tor only folding props applications) User programmable battery vos (Li Po or MINICAB} . User programmable low voltage cutoff selling : User programmable factory delay setting restore User programmable timing settings [lo enhance EGC efficiency and smoothness) User programmable doll acceleration sin ups Uor delicate gearbox and helicopter applications) .
* Automatic ESC electromagnetically the optimum motor timing Low (722 deg) ~ Renting far most 2 gale motors, 1 High 1230 insetting for motors withed spore poles; In most cases, automatic timing works well for all types of motors, However for high efficiency we recommend the Lew timing setting for 2 pole motors (general ins runners and high timing for poles and above (general outrunning, For higher speed. High timing can be set.
Using Your New ESC improper polarity or short circuit will damage the ESC therefore it is our responsibility to double called plugs for proper polarity and Hee fit BEFORE connecting the battery packs Aleut Tones The ESC is equipped with audible alert tones to indicate abnormal conditions al power up. 1 the ESC can't apter into working mode alter nonflowering ip. indicates that vou have not setup Throttle calibration 1.
of throttle signal for 2 second.
ch ever switch your transmitter OFF while the battery is connected to your £50. Duly connect our battery pack 1st before living and do not leave your battery pack connected tare dying: Candle your model with extreme care once t trey pack bs connected and keep away from the propeller at all times, Never stand in-line or directly in front of any rotating parts. s Monet immerse the BSC underwater while powered up. « Doff at a designated fling site and abide by the rules and guidelines set by our fling dub.
Motor does 1 work after powering up the EST ESC emits two Tong audible tones followed by two short beeps | fF) Reversed throttle channel calved the ESL to enter the programming mode, Enter the servo reverse menu on your transmitter and reverse the throttle channel Nate: Far Rutabaga radios set the throttle channel to Reverse, issue Possible Reason Action Mutilator vans in reverse rotation Motor steins running in flight Meany cables polarity between the £50 and the motor.
