400MM P-40B 55.1 1400 1192 46.9 2500g 88 .2 33.7 522.3 74.2 0.17 6 Please visit both our facebook fan page and our homepage for updated product information heep://www.facebook.com/FMSmodel www.fmsmodel.
WARNING WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before operating. Failure to operate the product correctly can result in damage to the product. personal property and cause serious injury. This is a sophisticated hobby product and NOT a toy. It must be operated with caution and common sense and requires in injury or damage to the product or other property. This product is not intended for use by children without direct adult supervision.
Table of Contents Introductions..................................................................................................................................................3 Contents of Kit...............................................................................................................................................3 Assemble the plane.......................................................................................................................................
Assemble the plane 1. Unpack the parts bag for aileron, which includes screws and linage rods. Install the linkage rods as shown in Figure 1. See page 9 for close up of the installation and suggestions for the linkage rod and servo arm hook up. Do the same on Flap assemblies as shown in Figure 2 and 3. fig2 fig1 fig3 2. Slide the wing tube into the wing holes. Ensure the the connector wires pass through the hole to the top side of the wing.
PA2.6*15mm fig5 fig6 3. Unpack the elevator parts bag and assemble using screw PM3.0*32mm and PM3.0*40mm, attach the linkage on the control horn. PM3.0*32mm PM3.0*40mm fig8 fig7 4. Turn over the fuselage so the bottom faces up and feed the connector wires thorough the hole in the fuselage. Secure the wing in place using 4 wing screws. PM3.
a. Lower the throttle and throttle trim to the lowest setting. Power on the Transmitter, then wait 5 seconds. b. Connect the battery to ESC and let the rear landing gear down using your transmitter and receiver. c. Assemble the Vertical Tail to the fuselage using the screw PWA 2.6*15mm. fig10 fig11 PWA2.6*15mm Install the battery 1. Apply the hook tape to the cable end of the battery (fig12). 2.
Connectors Diagram CH4 Plug for wing serial plugs CH2 CH1 CH6 Plug for elevator servo Plug for landing gear bay doors CH5 CH4 CH2 CH5C CH5B Plug for worm-gear retract servo Plug for rudder servo Serial plug for the right wing Serial plug for the left wing CH5B CH5B CH5C CH5C CH1 CH1 CH6 CH6 LED LED Get your model ready to fly Important ESC and model information 1. The ESC included with the model has a safe start.
The transmitter and model setup Before getting started, bind your receiver with your transmitter. Please refer to your Transmitter Manual for proper operation CAUTION: To prevent personal injury, DO NOT install the propeller assembly onto the motor shaft while testing the control surfaces. DO NOT arm the ESC and do not turn on the transmitter until the Transmitter Manual instructs you to do so.
Check the control throws The suggested control throw setting for FMS MODEL are as follows (dual rate setting): 24 23 35 13 15 20 Tips: At first flight, fly the model in low rate. The first time you use high rates, be sure to fly at low to medium speeds. High rate as listed are only for EXTREME maneuvering. Check the motor rotating direction The motor should rotate clockwise when viewing the plane from the rear.
Install the propeller and spinner Assemble the spinner and propeller as shown below. c f e b a d g Check the C.G.(Center of Gravity) When balancing your model, adjust the motor battery as necessary so the model is level or slightly nose down. This is the correct balance point for your model. After the first flights, the CG position can be adjusted for your personal preference. 1.
Before flying the model Find a suitable flying site Find a flying site clear of buildings, trees, power lines and other obstructions. Until you know how much area will be required and have mastered flying your plane in confined spaces, choose a site which is at least the size of two to three football fields - a flying field specifically for R/C planes is best. Never fly near people especially children who can wander unpredictably.
Flying course Take off While applying power, slowly steer to keep the model straight. the model should accelerate quickly. As the model gains flight speed you will want to climb at a steady and even rate. P40 will climb out at a nice angle of attack (AOA). Flying Always choose a wide-open space for flying your plane. It is ideal for you to fly at a sanctioned flying field. If you are not flying at an approved site always avoid flying near houses, trees, wires and buildings.
Troubleshooting 13
Spare parts list content FMSPK101 Fuselage FMSPK102 Main Wing Set FMSPK103 Vertical Stabilizer FMSPK104 Horizontial Stabilizer FMSPK105 Cockpit FMSPK106 Oil Tank FMSPK107 Front Landing Gear Door FMSPK108 Rear Landing Gear Door FMSPK109 Air Speed Head,Gun Set And Gunsight FMSPK110 Wing Bolt Plate FMSPK111 Spinner FMSPK112 Main Landing Gear Strut FMSPK113 Main Landing Gear System FMSPK114 Rear Landing Gear System FMSPK115 Linkage Rod FMSPK116 Screw Set FMSPK117 Decal Sheet FMSPK118 Tire Set FMSPK119 Pipe FMSP
ESC instruction 15
