A WARNING: Read the ENTIRE Instruction manual to become familiar with the features of the product before operating, Allure to operate the product correctly can result in damage lo the product, personal property and cause serious injury, This is a sophisticated hobby product and NOT a toy. bemusement operated with caution and common sense and enquirers some basic mechanical ability. Failure lo operate is Product in a sale and responsible manner could result In inlurvordamage to the product brother property.
1: The plastic control surface horns for the rudder and elevator are stapled to the bags containing the rudder and ale valor, lotion accidentally discard them. 2. install the elevator control surface horns with the screws provided in the small plastic bag on the bottom of the elevator surface, the side with a slide slots tha top. wn 3. Always make sure In halt lhe screws are seated info the back plates of the control ohms, Hs ver i that these are tight during flight in © 4.
1. Puttee Z-bend end of the linkage into . 4. There are three glass fiber fuses in the desired servo control horn hole. : different lengths for the main wing Hisatightftendshouidaliow the : connection. linkage to move just slightly within the © A: Horticulture hole to avoid binding up. : 8: intermediate lube : C: Long tube o 2.8nap clavicles into the surface control horn. : §. When sliding the tubes info the wings, : they should go in easily.
8. Use tubes ASB lo connective two lower | wing halves. Tube A is used for the : tarting doe (aft) tuba B ls used for the leading edge (front) of the wing. @ 8. Use small tantamount to attach the rear lower wing boll plate. Make sure that vou place the plate into 7. Use a brush grackle to apply a thin : the notch correctly. coat of glue where the two wing halves: The plate only fits right in one direction. fit together : Refer to pictures 10811 forth right . placement. 8.
10. Plate mounted the wrong way round. Mate that one side of the plate ls wider than the other and ihe plate wiliness it into the notch you try to mount i as shown in the picture. 43 Uses small amount of glue to secure the : upper wing bolt plates, There is no difference In between these two plates and they can be mounted dither way. 11. This is how the plate should be mounted. ei ian 12. Repeal sips 6-8 for the top wing. Use tube C instead ol ABB lo connect tha two wing halves.
Installing the elevator and rudder to the fuselage 4. Make sure there is no gap in between the rudder and the stabilizer. 1. Install the stabilizer to the aft part of the : fuselage and make sure that the notch faces up: (Screws: PA 2.6x35, PCS) no & Apply a thin coal of glue on both sides of the rudder hinge and slide the rudder 2. Makesure brotherliness of tha stabilizer forward into place. aligns with the center line of the fuselage. ame aac sas wid eae 3.
Selfie the provided machine screw lo lock rudder to the fuselage the rudder binge. Make sure toot secure © designated hides. the screw too tight 28 50 does not cattle the movement of the rudder. Wiggle the rudder control surface several times to make sure halt there [8 no excessive drag which might prevent the surface from moving freely. (Screw: PM3.0x30, Too) 7 8, Snap the elevator support rods lino place. There ars two rods in the kit, one for each side. install the nyl illustrated in has : #8.
Installing 1. Install the red gr landing gear with the provided self tapping screw. (Screw: PA 2 6x15, PCS) : 4, Align the tail wheel with the rudder as Zi Insert the Z-bend ends of the provided shown in the picture. Use a screwdriver linkage rods info the belle rank on the : to tighten the control connectors. rudder. : 3.
the fuselage 1. Position therewith as so the nose in front © 2. Allah the lower maid wing and the of the lower wing fits into the notch in the : landing singeing six of the provided forward part of the fuselage’s lower wing machine screws Two screws are used bay : forth rear wing boll plate, two for the Guide the two aileron servo cables : front wing plate {landing gear rear base} through the holes in the bottom of the ; and two for the landing gear front base. fuselage.
Installing the Part 1: install the inter plane strut and cabana 1. The way to identify and install the strut, First the strut base are designed fit the notch properly when the installation complete, there is no gap reveal between the base and the strut If not Irv fo fit the other end of the strut into the notch.
and rigging &.Before we mounted the top wing on the gaberdine and struts we must finish the netting work of the flying wires, 6. Thread the two end of the in stored nylon wire through the pre drilled bolthole middies two of the four hole}, the recommend length of the wire is 900mm, EEE a 4. Apothecary lino place as show and make sure tha cabana properly il into place with no slot reveal between the combination. ERR 7.
Installing the to 8. Well-distributed the glue on the struts © 10. Use screwdriver to tighten the four and top wing where the struts and top : machine screws to secure the wing to wing fitting together. : the cabana PCS) 1, Connect the other cluster of cross strain rapes with two siring hook gl each end of the ropes. Make sure the two lines are parallel connected, Tha strain connection on starboard and port side are the same. ® Peeves. : 9. Mount the top wing to the cabana and struts. 0.
SIS’ and strain rope Install install the propeller set 13. Adjust the control surface, make sure the trailing doe of the surface align : 1: Pul three propeller blades rightly onto with the wing root thralling edge. . the buck plate. Make sure the teller with This step are critical for the max : FMS 14X8" on the propeller face up. performance of aerobatic characteristic. 2. Cover the spinner middle part on the propeller.
step-8. propeller 3. Secure it using the provided screws in spinner package (PCs) 4, Verily the flatus of the propeller installation completed. 8. Slide the propeller assembly onto the motor shaft, Make sure the back plate I8 properly keyed into the hex on tha shaft, po &. Fit the front spinner in to place using the screw driver to secure the front spinner with one machine screw, 1PC) . Remove the canopy hatch from the fuselage by lifting the hatch at the rear band. 2.
ms Specification Of 68 UMBEL: 1. Switch Mode 2. Output: 5 0V/6A , 5. SVALBARD or 6. OVA switchable (Changeable with a blue jumper) 3. (2-65 Lip, 5-185 NiMH/NiCd) 4. Output Current: Continuous Current 64 Burst Cu rent 10A 5. Size:45. Omm*23. Ommx*10. Omm (Length*Width*Height) 6. Weight: 18. 0g Mote: We recommend use the jumper cap to connect the two middle pins in four for your safety flying. Allures: 1.
Specification Center Of Wingspan 400mm 58.1 in Length Di28TmmiBi hn Weight : 3300g/11640z CG Position. 90mm ; | Battery : 22.2V3300mAh Li-Po Battery 1 T ESC 1 BBA : Motor : 5060.KV360 Wing Area | 80 2am? Wing load : RC System : 4 Channel, 4 Servos And 1 Brush less ESC Cantor of Gravity When balance your model, adjust the motor gallery as necessary so the model is level or slightly nose down.
Problem Possible Cause Solution Aircraft will not respond to the throttle but responds to other controls, ESC snot armed. Throttle channel is reversed Lower throttle stick and throttle rim fo lowest settings. Hearse (throttle channel on frontiersman. Extra propelling or extra Vibration. Damaged spinner, propeller. motor or motor mount Loose propeller and spinner pairs. Propeller installed backwards. Replaced damaged pairs. Tighten parts for propeller adapter, propeller and spinner.
Range Check Your Radio System After final assembly, range check the radio system with the FMS PITTS. Refer {o your specific transmitter instruction manual for range test information. Take off and landing tips 1 Take off using Tull power. 2 Ensure that vou seat timer and land with plenty of battery power in reserve, 3. Never exceed 3 minutes to fiy with the maximum power others, 4. Never exceed the limited flying weight. First Flight Preparation 1. Remove and inspect contents.
AMA If you arena already a member of the AMA please join, The AMA ls the governing body of model aviation and membership provided Shabbily insurance coverage, protects modelers rights and interests and is required to fly al most RIC sites. Academy ol Model Aeronautics A 5151 East Memorial Drive ag wy Munchie, IN473D2-8252 Mae, § eons? SS Or via the Internet at: SEAR BURG Rs Academy of Model Aeronautics National Model Aircraft Safety Code Effective January 1, 2011 A.
Exceptions: #® Fred Flight fuses or devices that burn producing smoke and are securely attached to the model aircraft during flight. # Officially designated AMA Air Show Teams (AST) are authorized {o use devices and practices as defined within the Team AMA Program Document (AMA Document #718). 3.
