64MM F-15 V2 SIMPLE Easy assembly RIGID STRONG DURABLE EPO STABLE SMOOTH FLYING PERFORMANCE FMSMODEL.
WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before operating. Failure to operate the product correctly can result in damage to the product, personal property and cause serious injury. This is a sophisticated hobby product and NOT a toy. It must be operated with caution and common sense and failure to do so could result in injury or damage to the product or other property. This product is not intended for use by children without direct adult supervision.
Table of Contents Introduction ····························································································································3 Contents of Kit ························································································································4 Model Assembly ······················································································································5 Important ESC and model information ··············································
Wingspan: 715mm (28.1in) Overall Length: 980mm (38.6in) Flying Weight: Around 1025g (36.2 oz) Motor Size: Brushless 2840-KV3150 Wing Load: 66.5g/dm² (0.15oz/in²) Wing Area: 15.4dm² (238.7sq.in) ESC: 40A Servo: 9g Servo x 5 Contents of Kit Before assembly, please inspect the contents of the kit. The photo below details the contents of the kit and labels.
Model Assembly Main Wing Installation 1.Slide the wing tube into the fuselage (fig1). 2.Install the left and right wing over the wing tube and into the wing slot of the fuselage (fig1). fig1 3.Secure the left and right wing to the fuselage using the 4 screws included (fig2) HKM3.
Model Assembly Horizontal Stabilizer Installation: Carefully apply CA to the base and the side of the rear fuselage slot. Install the stabilizer into place. Ensure the control horn faces down as shown (fig3). Note: Ensure the stabilizer horizontal axis is parallel to the wing. Adjust any misalignment before the glue dries thoroughly. fig3 Vertical Stabilizer Installation: Carefully apply CA to the top rear fuselage slots. Install the vertical stabilizer into place (fig4).
Model Assembly Clevis Installation: Install the clevis. (fig5) Refer to the Clevis Installation on page 12. fig5 Landing Gear Installation: 1. Install the main landing gear with the included screws (fig6). 2. Install the front landing gear and then tighten the screw (fig7). KA2.
Model Assembly Missile Installation: 1. Apply glue on the missile with CA and slide the whole missile set into the rails on each wing (fig8/fig9). fig9 Required Adhesives: fig8 Foam Safe Medium CA Nose Cone Installation: Apply the nose cone to the front fuselage as diagram shows. Ensure the nose cone is on the correct side.
Battery and radio installation 1. Apply the hook tape to the cable end of the battery (fig 11). 2. Slide the battery into the battery compartment with the power supply cable toward the fore-end of the plane. Note: you may need to relocate the battery position to achieve the correct CG for your model. fig11 3. Check the connection diagram below for more information (fig12.
Get your model ready to fly Important ESC and model information 1. The ESC included with the model has a safe start. If the motor battery is connected to the ESC and the throttle stick is not in the low throttle or off position, the motor will not start until the throttle stick is moved to the low throttle or off position. Once the throttle stick is moved to the low throttle or off position, the motor will emit a series of beeps.
Check the control throws The suggested control throw setting for FMS MODEL are as follows (dual rate setting): 14 12 10 8 Tips: On first flight, fly the model in low rate. The first time you use high rates, be sure to fly at low to medium speeds. High rate, as listed, is only for EXTREME maneuvering.
Clevis Installation a. Pull the tube from the clevis to the linkage. b. Carefully spread the clevis, then insert the clevis pin into the desired hole in the control horn. c. Move the tube to hold the clevis on the control horn. a. d. b. e. c. f. Control Horn and Servo Arm Settings The table shows the factory settings for the control horns and servo arms. Fly the aircraft at the factory settings before making changes.
Check the C.G. (Center of Gravity) When balancing your model, adjust the motor battery as necessary so the model is level or slightly nose down. This is the correct balance point for your model. After the first flights, the CG position can be adjusted for your personal preference. 1. The recommended Center of Gravity (CG) location for your model is (85-90mm) forward from the leading edge of the main wing (as shown) with the battery pack installed. Mark the location of the CG on top of the wing. 2.
Before flying the model Find a suitable flying site Find a flying site clear of buildings, trees, power lines and other obstructions. Until you know how much area will be required and have mastered flying your plane in confined spaces, choose a site which is at least the size of two to three football fields - a flying field specifically for R/C planes is best. Never fly near people - especially children, who can wander unpredictably.
Flying course Take off While applying power, slowly steer to keep the model straight. The model should accelerate quickly. As the model gains flight speed you will want to climb at a steady and even rate. It will climb out at a nice angle of attack (AOA). Flying Always choose a wide-open space for flying your plane. It is ideal for you to fly at a sanctioned flying field. If you are not flying at an approved site always avoid flying near houses, trees, wires and buildings.
Troubleshooting 16
Spare parts list content FMSPZ101 FMSPZ102 FMSPZ103 FMSPZ104 FMSPZ105 FMSPZ106 FMSPZ107 FMSPZ108 FMSPZ109 FMSPZ110 FMSPZ111 FMS64MM11B FMSKV3150 PRESC009 FMSSER9GP FMSSER9GR FMSSER9G54 Fuselage Main Wing Set Rudder Elevator Missle & Oil Tank Canopy Cowl Landing Gear Set Linkage Rod Pipe Decal Sheet 64mm Ducted Fan 2840-KV3150 Motor 40A ESC (With 430mm length input cable) 9g Servo Positive 9g Servo Reverse 9g Servo 54 Degree Visit our website to see photos of this product: www.fmsmodel.
ESC instruction Brushless Speed Controller Battery Pack A quality connector is essential ESC Motor Brushless Controller Receiver 18
